SOMFY ALTUS User Manual
Altus 6 Step Visual Reference Guide
Remain clear of moving products when performing these operations.
STEP 1
Initiate programming by pressing
both the UP and DOWN buttons
at the same time until the motor jogs.*
NOTE: After every command the motor will jog
to confirm.
STEP 3
Bring the motor to your desired upper
limit. Press and hold the MY and
DOWN buttons until the motor moves
DOWN, then release. Stop the motor where
the LOWER limit should be set, you can
adjust by pressing the or buttons.
For larger units, set limit at ½ down or out
position initially. Finalize programming and
allow motor to rest for 10 minutes. Then
follow steps below to adjust to final outer
limit.
my
STEP 5
Press and hold the MY (stop) button until
the shade jogs to confirm the limit setting.
my
STEP 2
my
Check the direction of operation. Press and
hold the DOWN button and confirm it
moves the motor down or out (the motor
will be in momentary mode). To change
the direction, press and hold the MY
my
(stop) button until the motor jogs.
my
STEP 4
Press and hold the MY (stop) and UP
my
buttons until the motor starts to move up,
then release. The motor will stop at the
original upper point.
my
my
my
STEP 6
my
Press and hold the Program button on the
back of the transmitter until the motor jogs.
It will now operate in a maintained fashion.
Double check the limits as a precaution.
Programming
Button
*Jog - Brief back and forth or up and down movement from the motor.
To Adjust Limits
my
To change a limit: Move the motor to its current limit position to be changed and let it stop. Press the
UP and DOWN buttons simultaneously until the motor jogs, then release. Adjust to a new limit
position. Press the MY (stop) button until the motor jogs, then release. Check the new limit.
my
To add a remote/channel or sun or wind sensor: First select the remote/channel that is already
programmed to the motor and press the program button on the back until the motor jogs. Then select the
remote/channel/sun or wind sensor that you would like to add and press the program button on that
until the motor jogs.
To reset a previously programmed motor: you will need to disconnect power (120V AC) for 2 seconds,
reconnect for 10 seconds, disconnect for another 2 seconds and reconnect. The motor should start to
move/jog and then stop on its own (if this does not happen, continue to perform the disconnects until
Programming
Button
it does). Once the motor stops, press and hold the programming button on the back of the remote and
count to ten without letting go. The motor should jog twice.
my
If using a multi-channel remote, begin by selecting channel to be changed.
Please contact SOMFY at for detailed installation instructions.877-22SOMFY or www.somfypro.com
© SOMFY SYSTEMS, INC. 11/2013
S-0027
RTS CMO Visual Reference Guide
Remain clear of moving products when performing these operations.
STEP 1 STEP 2
Make sure the limit setting
buttons are depressed
into the RTS CMO motor.
Initiate programming by pressing both
the UP and DOWN buttons at the
same time until the motor jogs.*
my
STEP 3
Check the direction of operation.
Press and hold the DOWN button
and confirm it moves the motor
down or out (the motor will be in
momentary fashion). To change the
direction press and hold the MY
my
my
my
STEP 4
SET UPPER LIMIT
Press and hold the UP button
of the remote to move the motor
to the desired UPPER limit position,
then release. Press and release
the UPPER limit button on the motor.
(stop) button until the motor jogs.
STEP 5 STEP 6
SET LOWER LIMIT
Press and hold the DOWN button of the
my
remote to move the motor to the desired lower
limit position, then release. Press and release
the lower limit button on the motor.
For larger
units, set limit at ½ down or out position
initially. Finalize programming and allow motor
to rest for 10 minutes. Then follow steps below
to adjust to final outer limit.
*Jog - Brief back and forth or up and down movement from the motor.
USER MODE
Once the desired limits are set, press
and hold the Program button on the
back of the transmitter until the motor
jogs, then release. The motor will now
operate in maintained fashion.
Double check the limits as a precaution.
my
Programming
Button
my
Programming
Button
my
© SOMFY SYSTEMS, INC. 11/2013
To change the limit settings: ensure corresponding limit
Press the MY (stop) button on the remote then
my
button is depressed. Next, repeat steps 4 or 5 keeping in mind that the motor may be operating in a
maintained mode. Therefore you may only need to press the UP or DOWN buttons momentarily to
move the motor, and the MY (stop) button must be pressed in order to stop it.
my
To add a remote/channel or sun or wind sensor: First select the remote/channel that is already programmed to
the motor and press the program button on the back until the motor jogs. Then select the remote/channel/sun or
wind sensor that you would like to add and press the program button on that until the motor jogs.
To reset a previously programmed motor: you will need to disconnect power (120V AC) for 2 seconds,
reconnect for 10 seconds, disconnect for another 2 seconds and reconnect. The motor should start to move/jog
and then stop on its own (if this does not happen, continue to perform the disconnects until it does). Once the
motor stops, press and hold the programming button on the back of the remote until the motor jogs one time.
If using a multi-channel remote, begin by selecting channel to be changed.
Please contact SOMFY at for detailed installation instructions.877-22SOMFY or www.somfypro.com
S-0027
Loading...