How it Works
SOLTEK
Loading...
SL-75DRV-X
User Manual
99 pgs2.61 Mb0

SOLTEK SL-75DRV-X User Manual

Download
Page 1
R
The Soul Of Computer Technology
SL-75DRV/75DRV-X
USER MANUAL v1.4
Page 2
NOTICE
Product Model : SL-75DRV/75DRV-X Manual Revision : V1.4 Release Date : August 2001
• AMD Athlon ThunderbirdTM, and DuronTM processors are trademarks of AMD Corporation.
• VIA, KT-133, VT8363 and VT82C686A are trademarks of VIA Corporation.
• Norton AntiVirus, Norton Ghost are trademarks of Symantec Corporation.
T
his Users Guide & Technical Reference is to help system manu­ facturers and end-users set up and install the mainboard. Every effort has been made to ensure that the information in this manual is accurate. Soltek Computer Inc. is not responsible for print­ing or clerical errors. Information in this document is subject to change without notice and does not represent a commitment on the part of Soltek Computer Inc. No part of this manual may be reproduced, transmitted, translated into any language in any form or by any means, electronic or mechanical, including photocopying and recording, for any purpose without the express written permission of Soltek Computer Inc. Companies and products mentioned in this manual are for identifi­cation purpose only. Product names appearing in this manual may or may not be registered trademarks or copyrights of their respec­tive companies.
Soltek Computer Inc. provides this manual “As is “ without warranty of any kind, either express or implied, including but not limited to the implied warranties or conditions of merchantability or fitness for a particular purpose. In no event shall Soltek Computer Inc. be liable for any loss or profits, loss of business, loss of use or data, interruption of business, or for indirect, special, incidental, or consequential damages of any kind, even if Soltek Computer Inc. has been advised of the possibility of such damages arising from any defect or error in this manual or product.
Copyright © 2001 Soltek Computer Inc. All Rights Reserved.
Page 3
SOLTEK AROUND THE WORLD
SOLTEK COMPUTER INC.
Address : 7F, No. 306-3, Ta-Tung Rd, Sec.1, Hsi-Chih, Taipei-
Hsien, Taiwan, R.O.C.
Telephone : 886-2-2642-9060 Fax : 886-2-2642-9065 E-mail : sales@soltek.com.tw Web site : http://www.soltek.com.tw
SOUL TECHNOLOGY EUROPE B.V.
Address : Hongkongstraat 55, 3047 BP Rotterdam. The Neth-
erlands
Telephone : 31-10-2457492 Fax : 31-10-2457493 E-mail : sales@soultech-europe.com Web site : http://www.soultech-europe.com
Page 4
75DRV/75DRV-X
4
CONTENT
CHAPTER 1 INTRODUCTION ................................................. 9
1-1 MAINBOARD SPECIFICATION ............................................... 10
1-1.1 PROCESSOR ................................................................................. 10
1-1.2 CHIPSET ......................................................................................... 10
1-1.3 AWARD BIOS V6.0 SUPPORTING................................................. 10
1-1.4 SOUND CONTROLLER .................................................................. 10
1-1.5 POWER MANAGEMENT ................................................................ 10
1-1.6 FULL FEATURED ACCELERATED GRAPHICS PORTS (AGP)
CONTROLLER ................................................................................ 11
1-1.7 MULTI-I/O FUNCTION .................................................................... 11
1-1.8 EXPANSION SLOTS ....................................................................... 11
1-1.9 ADVANCED HIGH PERFORMANCE SDR/DDR DRAM
CONTROLLER ............................................................................... 11
1-1.10 FORM FACTOR ............................................................................ 12
1-1.11 HARDWARE MONITOR ................................................................ 12
1-1.12 OTHERS ....................................................................................... 12
1-2 MAINBOARD LAYOUT ............................................................ 13
1-2.1 Mainboard Layout --- 75DRV .......................................................... 13
1-2.2 Mainboard Layout --- 75DRV-X ....................................................... 14
1-3 CHIPSET DIAGRAM--- 75DRV/75DRV-X ............................... 15
CHAPTER 2 HARDWARE SETUP......................................... 17
2-1 CPU INSTALLATION ............................................................... 18
2-2 MEMORY INSTALLATION....................................................... 19
2-3 ACCELERATED GRAPHICS PORT(AGP) PRO INSTALLATION ... 21
Page 5
5
2-4 HDD/FDD INSTALLATION ....................................................... 22
2-5 SWITCH SETTING FOR CPU FREQUENCY AND VOLTAGE 24
2-5.1 Information On AMD Socket 462 Processor (Model4, 5 Products) . 24 2-5.2 Information On AMD Socket 462 Processor (Model6, 7 Products) . 25
2-5.3 Frequency Ratio Select (By SW1 DIP1-DIP5) ................................ 26
2-5.4 Processor Core Voltage Select (By SW2 DIP1-DIP6)..................... 27
2-5.5 CPU External Frequency Setting (By SW3) .................................... 28
2-6 JUMPER SETTING FOR DEVICES ON BOARD .................... 29
2-6.1 JP1/JP2 Memory Module Voltage Select ........................................ 29
2-6.2 JP17 Power Lost Resume ............................................................... 30
2-6.3 JP18/19 AGP Voltage Select ........................................................... 30
2-6.4 JBAT1 For Clear CMOS Data ......................................................... 31
2-7 CONNECTORS CONFIGURATIONS ...................................... 32
2-7.1 On Board FAN Connector (FAN1, FAN2, FAN3, FAN4) .................. 32
2-7.2 WOL1 Wake On LAN ...................................................................... 33
2-7.3 CD-ROM Audio Connector (JCD_IN1) ............................................ 33
2-7.4 Thermal Sensor Connector (RT2) ................................................... 34
2-7.5 Complex Header CON1 .................................................................. 35
2-7.6 ATX Power Supply Connector ......................................................... 36
2-7.7 Chassis Panel Connector ............................................................... 37
2-7.8 Smart Card Reader Connector (SCR1) .......................................... 38
2-7.9 Communication And Networking Riser Slot (CNR) ......................... 39
2-7.10 USB Header (USB2/USB3 Header) .............................................. 40
2-7.11 PS/2 Mouse And PS/2 Keyboard .................................................. 40
2-8 VOICE DIAGNOSTIC FUNCTION FOR 75DRV-X ONLY ....... 41
2-8.1 JP10 VD-Tech II Language Select .................................................. 42
Page 6
75DRV/75DRV-X
6
CHAPTER 3 SOFTWARE SETUP ......................................... 44
3-1 VIA CHIPSET DRIVER INSTALLATION (4-IN-1 DRIVER) ...... 45
3-2 HARDWARE MONITOR INSTALLATION ................................ 48
3-3 AC’97 AUDIO CODEC DRIVER INSTALLATION .................... 50
CHAPTER 4 BIOS SETUP ..................................................... 52
4-1 WHAT IS BIOS SETUP............................................................ 53
4-2 HOW TO RUN BIOS SETUP ................................................... 53
4-3 WHAT IS CMOS ...................................................................... 53
4-4 WHAT IS POST ....................................................................... 53
4-5 BIOS UPGRADE ..................................................................... 53
4-5.1 BEFORE UPGRADING BIOS ......................................................... 54
4-5.2 UPGRADE PROCESS .................................................................... 54
4-6 BIOS SETUP --- CMOS SETUP UTILITY................................ 58
4-6.1 CMOS SETUP UTILITY .................................................................. 58
4-6.2 STANDARD CMOS SETUP ............................................................ 59
4-6.3 ADVANCED BIOS FEATURES ....................................................... 62
4-6.4 ADVANCED CHIPSET FEATURES ................................................ 66
4-6.5 INTEGRATED PERIPHERALS ....................................................... 71
4-6.6 POWER MANAGEMENT SETUP ................................................... 77
4-6.7 PNP / PCI CONFIGURATION ......................................................... 83
4-6.8 SMARTDOC ANTI-BURN SHIELD ................................................. 86
4-6.9 FREQUENCY/VOLTAGE CONTROL.............................................. 88
4-6.10 LOAD OPTIMIZED DEFAULTS..................................................... 91
4-6.11 SET SUPERVISOR / USER PASSWORD .................................... 91
4-6.12 SAVE & EXIT SETUP.................................................................... 92
4-6.13 EXIT WITHOUT SAVING .............................................................. 92
Page 7
7
APPENDICES ......................................................................... 94
APPENDIX-1 TECHNICAL TERMS .............................................. 95
APPENDIX-2 IDENTIFYING BIOS VERSION AND BIOS ............ 96
PART NUMBER ..................................................... 96
APPENDIX-3 IDENTIFYING MAINBOARD MODEL NUMBER .... 98
Page 8
75DRV/75DRV-X
8
Mainboard
====Support CD ====User’s Manual ====Bundled Bonus Pack CD ====Bundled Bonus Pack Manual ====Temperature Sensor Cable ====ATA66/100 IDE Cable ====RS232 Cable
FDD Cable
ITEM LIST CHECKUP
Page 9
Chapter 1 Introduction
9
CHAPTER 1
INTRODUCTION
This chapter contains the following topics :
1-1 MAINBOARD SPECIFICATION 1-2 MAINBOARD LAYOUT 1-3 CHIPSET DIAGRAM
• This chapter briefly introduces the characteristics of the mainboards. It includes the information regarding the chipset, CPU types, built-in functions and layout. Users will have more ideas about mainboards after reading this chapter.
Page 10
75DRV/75DRV-X
10
1-1 MAINBOARD SPECIFICATION
1-1.1 PROCESSOR
• Supporting AMD Athlon Thunderbird processor up to 1.5GHz or above.
• Supporting AMD Athlon Duron
processor up to 1.2GHz or above.
• Supporting 200MHz & 266MHz FSB bus.
• Supporting Processor VID(voltage ID) and FID(Frequency ID) auto detection.
• Supporting Atholon 4 Processors.
1-1.2 CHIPSET
• North Bridge VIA VT8366 KT-266 AMD ATHLONTM NORTH BRIDGE.
• South Bridge VIA VT8233 VLINK CLIENT HIGHLY INTEGRATED SOUTH BRIDGE.
• LPC I/O ITE 8705.
1-1.3 AWARD BIOS V6.0 SUPPORTING
• Plug & Play V1.0.
• Flash Memory for easy upgrade.
• Year 2000 compliant.
• BIOS writing protection.
• SmartDOC Anti-Burn shield.
1-1.4 SOUND CONTROLLER
• SoundBlaster Pro Hardware and Direct Sound Ready AC97 Digital Audio Controller with Codec onboard.
1-1.5 POWER MANAGEMENT
• ACPI 1.0 compliant (Advanced Configuration and Power Interface).
• APM V1.2 compliant (legacy power management).
• Supporting ACPI suspend STR mode (Suspend To DRAM) and POS mode (Power On Suspend).
• System event monitoring with two event classes.
• Supporting PS/2 Keyboard & Mouse power on.
• Supporting Wake On LAN (WOL) & Wake On Modem.
• Supporting real time clock (RTC) with date alarm, month alarm, and century field.
• USB boot-up Function.
Page 11
Chapter 1 Introduction
11
1-1.6 FULL FEATURED ACCELERATED GRAPHICS PORTS (AGP) CONTROLLER
• AGP v2.0 compliant.
• Supports Side Band Addressing(SBA) mode (non-multiplexed address / data).
• Supporting 66MHz 1x, 2x, and 4x modes for AD and SBA signaling.
1-1.7 MULTI-I/O FUNCTION
• Two UltraDMA-33/66/100 Master Mode PCI EIDE ports.
• Two UARTs for complete Serial Ports.
• One dedicated IR connector:
--At third serial port dedicated to IR function either through the two complete serial ports or the third dedicated port Infrared-IrDA (HPSIR) and ASK( Amplitude Shift Keyed) IR.
• Multi-mode parallel connector supporting:
--Standard mode, ECP and EPP.
• Floppy Disk connector supporting:
--One FDDs with drive swap function.
• Universal Serial Bus connector supporting:
-- USB v1.1 and Intel Universal HCI v1.1 compatible.
-- 2 built-in USB connectors, in addition to one internal USB header which requires
a USB cable to support 2 more optional USB ports.
• PS/2 keyboard connector.
• PS/2 Mouse connector.
1-1.8 EXPANSION SLOTS
• Five PCI bus Master slots.
• One CNR slot.
• One AGP PRO 4x mode slot.
• Three 184-pin DIMM slots.
• One SCR (Smart Card Reader) slot.
1-1.9 ADVANCED HIGH PERFORMANCE SDR/DDR DRAM CONTROLLER
• Supporting memory size up to 3GB.
• Supporting 184-pin DDR SDRAM type only.
• Supporting PC1600 and PC2100 DDR SDRAM.
Page 12
75DRV/75DRV-X
12
1-1.10 FORM FACTOR
• ATX form factor, 4- layer PCB.
• Mainboard size 22.0cm x 30.5cm.
1-1.11 HARDWARE MONITOR
• Programmable control, status to provide, monitoring and alarm for flexible desktop management (software include).
• 5 positive voltage statuses monitoring.
• 2 temperatures statuses monitoring.
• 2 Fan-speeds statuses monitoring.
1-1.12 OTHERS
• Supporting VD-Tech II function (For 75DRV-X only).
Page 13
Chapter 1 Introduction
13
1-2 MAINBOARD LAYOUT
1-2.1 Mainboard Layout --- 75DRV
USB2
1
16
1
16
USB3
CNR 1
FLASH BIOS
USB0
USB1
PS/2
MOUSE
PS/2
K/B
LPT1
COM1COM2
GAME/MIDI PORT
MIC
SW1
ON
DIP
5 4 3 2 1
SW2
ON
DIP
6 5 4 3 2 1
CN1
ON
DIP
1 2 3 4 5
SW3
FAN1
1 3
FAN3
1 3
CON1
SAPK RST PLED SLED
HDD/LED IR PWR SUSPEND
++
--
+
-
16 30
1 15
RT2
SCR1
JBAT1
1 3
JP1
JP2
1 3
1 3
WOL1
1 3
4
1
JCD_IN1
1 3
JP17
PCI 1
PCI 2
PCI 3
PCI 4
PCI 5
SSF1
ZD1
DDR 266
AGP PRO 4X
FDC1
IDE1
IDE2
VIA
VT8233
AC'97 Codec
LPC I/O
Controller
VIA
VT8366
Li
Battery
FAN2
1 3
Clock
Generator
FAN4
1 3
LINE
OUT
LINE
IN
JP18
JP19
1 3
1 3
SOCKET A
RT1
Using non-compliant memory with higher bus clock (over clocking) may severely compromise the integrity of system.
Page 14
75DRV/75DRV-X
14
USB2
1
16
1
16
USB3
CNR 1
FLASH BIOS
USB0
USB1
PS/2
MOUSE
PS/2
K/B
LPT1
COM1COM2
GAME/MIDI PORT
MIC
SW1
ON
DIP
5 4 3 2 1
SW2
ON
DIP
6 5 4 3 2 1
CN1
ON
DIP
1 2 3 4 5
SW3
FAN1
1 3
FAN3
1 3
CON1
SAPK RST PLED SLED
HDD/LED IR PWR SUSPEND
++
--
+
-
16 30
1 15
RT2
SCR1
JBAT1
1 3
JP1
JP2
1 3
1 3
WOL1
1 3
4
1
JCD_IN1
1 3
JP17
PCI 1
PCI 2
PCI 3
PCI 4
PCI 5
SSF1
ZD1
DDR 266
AGP PRO 4X
FDC1
IDE1
IDE2
VIA
VT8233
AC'97 Codec
LPC I/O
Controller
VIA
VT8366
Li
Battery
FAN2
1 3
Clock
Generator
FAN4
1 3
LINE
OUT
LINE
IN
JP18
JP19
1 3
1 3
SOCKET A
RT1
VD-¤ TECH
JP10
1 3
1-2.2 Mainboard Layout --- 75DRV-X
Using non-compliant memory with higher bus clock (over clocking) may severely compromise the integrity of system.
Page 15
Chapter 1 Introduction
15
1-3 CHIPSET DIAGRAM--- 75DRV/75DRV-X
• The VT8366 and VT8233 chipset is a high performance, cost-effective and energy efficient system controller for the implementation of AGP / PCI / ISA desktop personal computer system based on 64-bit Socket-A (AMD Athlon) processors.
DDR Vlink
Host North
552 BGA
VT8233
Vlink
Client South
352 BGA
3D
Graphics
Controller
Athlon
Host CPU
SDR/VCM
& DDR
SDRAM
Clock
Buffer
Clock
Generator
SDR/DDR Memory Bus
AGP Bus
SYSCLK, SYSCLK# INTR, NMI, SM#, STPCLK#, IGNNE#, FERR#, A20M#, PWROK, INIT#, RESET#
GCLK
PCLK
PCKRUN#
ATA33/66/100
MII/LAN
6x USB
LPC
SMBus
Power Plan & Peripheral Control
GPIO and ACPI Events
PCI Bus
CKE#
MCLK
HCLK
PCLK
CPUSTP#
PCISTP#
SUSCLK, SUSST1#
GCKRUN#
Address
Out
CFWDRST
CONNECT
PROCRDY
In
Data
VT8366
Diagram of Apollo Pro266 System Block Using the VT8233 V-Link
South Bridge
Page 16
16
75DRV/75DRV-X
MEMO
MEM
O
Page 17
17
Chapter 2 Hardware Setup
CHAPTER 2
HARDWARE SETUP
2-1 CPU INSTALLATION 2-2 MEMORY INSTALLATION 2-3 AGP PRO INSTALLATION 2-4 HDD/FDD INSTALLATION 2-5 SWITCH SETTING FOR CPU FREQUENCY AND VOLTAGE 2-6 JUMPER SETTING FOR DEVICES ON BOARD 2-7 CONNECTORS CONFIGURATION 2-8 VOICE DIAGNOSTIC FUNCTION FOR 75DRV-X ONLY
This chapter contains the following topics :
ATTENTION !!!
1. Please refer to your processor installation or other documentation attached to your CPU for detailed in­stalling instruction.
2. Installing a heat sink and cooling fan is necessary for proper heat dissipation from your CPU. Incorrect installation may result in overheating and damage of your CPU.
3. Before changing the setting of CPU Vcore from BIOS program, user SHOULD make sure of correct speci­fication both of CPU CLOCK and RATIO. Incorrect setting may cause damage to your CPU.
Page 18
18
75DRV/75DRV-X
WARNING !!!
• Make sure that +5V DCV and +3.3 DCV capabilities of your power supply are suitable for the processor.
• Any attempt to operate the AMD Athlon or Duron processor without a suitable cooling Fan will damage processor and other component.
2-1 CPU INSTALLATION
SOCKET 462
SOCKET 462
A
M
D
Take notice of the red circles as shown below. While insert­ing the CPU into the socket, you can find out there is a definite pin orientation for CPU and socket.
2
Pull out the lever from the socket, and then raise the le­ver up to a 90-degree angle.
1
A
M
D
S
O
C
K
E
T
4
6
2
Make sure that the CPU is
placed into the socket tightly. Then lower down the level to complete the CPU installation.
3
Page 19
19
Chapter 2 Hardware Setup
Installing DIMM
• Make sure you have the correct memory module type for your mainboard.
• Insert the module(s) as shown below, DIMMs have 184-pins and one notch that will be matched by the onboard DIMM socket. Memory modules are installed by inserting them straight into the slot until they “click” in the right place. They only fit in one direction, so do not force them in by a wrong direction.
184-Pin DIMM Notch Key Definitions(2.5V)
DRAM Key Position Voltage Key Position
2.5V
2-2 MEMORY INSTALLATION
Removing DIMM
• Press down the holding clips on both sides of a DIMM socket and the module will be released from it.
WARNING!!!
• Make sure to unplug your power supply before adding or removing memory modules or other system components. Failure to do so may cause severe damage to both your mainboard and expansion cards.
• Be careful when inserting or removing DIMM. Forcing a DIMM in or out of a socket improperly may damage the memory module or the socket. Some DIMMs which contain EDO or FTP DRAM are incompliant with the mainboard. The M/B supports 2.5V true SDRAM DIMMs only.
Page 20
20
75DRV/75DRV-X
USB2
1
16
1
16
USB3
CNR 1
FLASH BIOS
USB0
USB1
PS/2
MOUSE
PS/2
K/B
LPT1
COM1COM2
GAME/MIDI PORT
MIC
SW1
ON
DIP
5 4 3 2 1
SW2
ON
DIP
6 5 4 3 2 1
CN1
ON
DIP
1 2 3 4 5
SW3
FAN1
1 3
FAN3
1 3
CON1
SAPK RST PLED SLED
HDD/LED IR PWR SUSPEND
++
--
+
-
16 30
1 15
RT2
SCR1
JBAT1
1 3
JP1
JP2
1 3
1 3
WOL1
1 3
4
1
JCD_IN1
1 3
JP17
PCI 1
PCI 2
PCI 3
PCI 4
PCI 5
SSF1
ZD1
DDR 266
AGP PRO 4X
FDC1
IDE1
IDE2
VIA
VT8233
AC'97
Codec
LPC I/O
Controller
VIA
VT8366
Li
Battery
FAN2
1 3
Clock
Generator
FAN4
1 3
LINE
OUT
LINE
IN
JP18
JP19
1 3
1 3
SOCKET A
RT1
VD-¤ TECH
JP10
1 3
NOTICE : When LED “ZD1” is on, meaning that
2.5V is operating and flowing into DIMM slots, please do not add or remove memory modules .
Page 21
21
Chapter 2 Hardware Setup
2-3 ACCELERATED GRAPHICS PORT(AGP) PRO INSTALLATION
• The AGP Pro connector is an extension of the existing AGP connector and it is compatible with existing AGP cards.
Accelerated Graphics Port (AGP) Pro Slot
Rib(inside slot)
20-pin bay
Rib(inside slot) 28-pin bay
AGP Accelerator
AGP Pro slot
blockader
Warning this section is only for AGP Pro
Red Label
CAUTION!!
The AGP Pro slot comes with a warning label over the 20-pin bay. Do not remove this label and the safety tab underneath if you use an AGP card without a retention notch. Without the labels, AGP cards may be placed into the wrong place, which certainly will damage your card, slot, and mainboard. Remove the label ONLY if you will be using an AGP Pro card.
Page 22
22
75DRV/75DRV-X
USB2
1
16
1
16
USB3
CNR 1
FLASH BIOS
USB0
USB1
PS/2
MOUSE
PS/2
K/B
LPT1
COM1COM2
GAME/MIDI PORT
MIC
SW1
ON
DIP
5 4 3 2 1
SW2
ON
DIP
6 5 4 3 2 1
CN1
ON
DIP
1 2 3 4 5
SW3
FAN1
1 3
FAN3
1 3
CON1
SAPK RST PLED SLED
HDD/LED IR PWR SUSPEND
++
--
+
-
16 30
1 15
RT2
SCR1
JBAT1
1 3
JP1
JP2
1 3
1 3
WOL1
1 3
4
1
JCD_IN1
1 3
JP17
PCI 1
PCI 2
PCI 3
PCI 4
PCI 5
SSF1
ZD1
DDR 266
AGP PRO 4X
FDC1
IDE1
IDE2
VIA
VT8233
AC'97 Codec
LPC I/O
Controller
VIA
VT8366
Li
Battery
FAN2
1 3
Clock
Generator
FAN4
1 3
LINE
OUT
LINE
IN
JP18
JP19
1 3
1 3
SOCKET A
RT1
VD-¤ TECH
JP10
1 3
• To install HDD (Hard Disk Drive), you may connect the cable’s blue con­ nector to the mainboard’s primary (IDE1) or secondary (IDE2) connector, and then connect the gray connector to your slave device and the black connector to your master device. If you install two hard disks, you must configure the second drive to Slave mode by setting its jumper accordingly. Please refer to your hard disk documentation for the jumper settings.
Hard Disk Drive Connector: Orient the red line on the IDE ribbon cable to Pin1.
2-4 HDD/FDD INSTALLATION
Gray connector
Blue connector
IDE Cable
Black connector
red line
Page 23
23
Chapter 2 Hardware Setup
USB2
1
16
1
16
USB3
CNR 1
FLASH BIOS
USB0
USB1
PS/2
MOUSE
PS/2
K/B
LPT1
COM1COM2
GAME/MIDI PORT
MIC
SW1
ON
DIP
5 4 3 2 1
SW2
ON
DIP
6 5 4 3 2 1
CN1
ON
DIP
1 2 3 4 5
SW3
FAN1
1 3
FAN3
1 3
CON1
SAPK RST PLED SLED HDD/LED IR PWR SUSPEND
++
--
+
-
16 30
1 15
RT2
SCR1
JBAT1
1 3
JP1
JP2
1 3
1 3
WOL1
1 3
4
1
JCD_IN1
1 3
JP17
PCI 1
PCI 2
PCI 3
PCI 4
PCI 5
SSF1
ZD1
DDR 266
AGP PRO 4X
FDC1
IDE1
IDE2
VIA
VT8233
AC'97 Codec
LPC I/O
Controller
VIA
VT8366
Li
Battery
FAN2
1 3
Clock
Generator
FAN4
1 3
LINE
OUT
LINE
IN
JP18
JP19
1 3
1 3
SOCKET A
RT1
VD-¤ TECH
JP10
1 3
• To install FDD (Floppy Disk Drive), you may connect the single end to the board , and connect two plugs on the other end to the floppy drives.
Floppy Disk Drive Connector: Orient the red line on the floppy ribbon cable to Pin1.
FDD Cable
To 1st Floppy Drive
To mainboard
To 2nd Floppy Drive
red line
Page 24
24
75DRV/75DRV-X
2-5.1 Information On AMD Socket 462 Processor (Model4, 5 Products)
• On the AMD Socket 462 Processor, you can find a codified identification marking which is to provide useful information about the CPU. The marking is interpreted as below.
2-5 SWITCH SETTING FOR CPU FREQUENCY AND VOLTAGE
AMD
XXXXXXXXXXX XXXXXXXXXXXX XXXXXXX XXXXXXXXX XXXXXXXXXXX XXXX
AMD XXXX
A 0850
0850
A P T 3 B
T 3 B
Speed: 0850= 850MHz, 0900= 900MHz, 1000= 1000MHz, 1100= 1100MHz, etc.
Package Type: M= Card Module, A= PGA.
Operating Voltage: S= 1.5V, U= 1.6V, P= 1.7V, M= 1.75V, N= 1.8V.
Case Temperature: Q= 60
0
C, X= 650C, R= 700C, Y= 750C,
T= 90
0
C, S=950C.
Size of L2 Cache: 1= 64Kbyte, 2= 128Kbyte, 3= 256Kbyte.
Max FSB: A= B= 200MHz, C or others= 266MHz. (For correct FSB setting, please refer to next chapter)
Family/Architecture: A= AMD Athlon™Model 4 Processor Architure. D= AMD Duron™Processor Architecture.
1
2
3
4567
1
2
3
4
5
6
7
Page 25
25
Chapter 2 Hardware Setup
Speed: 0900= 900MHz, 1000= 1000MHz, 1100= 1100MHz, 1133=1133MHz, 1200=1200MHz, 1300=1300MHz, 1333=1333MHz, 1400=1400MHz, 1500=1500MHz, 1533=1533MHz etc.
Package Type: A= PGA.
Operating Voltage: M= 1.75V, N= 1.8V.
Case Temperature: T= 90
0
C, S=950C.
Size of L2 Cache: 1= 64Kbyte, 3= 256Kbyte.
Max FSB: B= 200MHz, C= 266MHz.
Family/Architecture: A= AMD Athlon™Model 4 Processor Architure. D= AMD Duron™ Model 7 Processor Architecture.
Generation: HD=Desktop Processor.
1
2
3
4
5
6
7
8
AMD
XXXXXXXXXXX XXXXXXXXXXXX XXXXXXX XXXXXXXXX XXXXXXXXXXX XXXX
AMD XXXX
A HD 1533 A N S 3 C
1
2
3
4 5
6
7 8
2-5.2 Information On AMD Socket 462 Processor (Model6, 7 Products)
Page 26
26
75DRV/75DRV-X
USB0
USB1
PS/2
MOUSE
PS/2
K/B
LPT1
COM1COM2
GAME/MIDI PORT
MIC
SW1
ON
DIP
5 4 3 2 1
SW2
ON
DIP
6 5 4 3 2 1
CN1
ON
DIP
1 2 3 4 5
SW3
FAN1
1 3
JP1
JP2
3
3
SSF1
ZD1
DDR 266
AGP PRO 4X
VIA
VT8366
FAN2
1 3
Clock
Generator
FAN4
1 3
LINE
OUT
LINE
IN
SOCKET A
RT1
2-5.3 Frequency Ratio Select (By SW1 DIP1-DIP5)
• The AMD Athlon and Duron processors provides four Frequency ID signals (FID) for the system controller to indicate the SYSTCLK multiplier at which the processor core operates. Normally, multiplier (or bus ratio) is detected automatically. Therefore, if the processor does not support the function, then “Bus Ratio” can not be selected.
• When DIP5 of SW1 is on, LED “SSF1” will be on, and light is on, it means that Bus Ratio Select Function is enabled. So as long as your CPU supports Bus Ratio Select function, then Bus Ratio can be selected by users.
SSF1
NOTICE : Setting of multiplier
12.5x or above will depend on the type of CPU on board .
* Setting of will depend on the type of CPU on board Multiplier 12.5x or
above.
SW1 DIP1 ~ DIP4 SETTING SW1 DIP5
5.5x
ONDIP
5 4 3 2 1
ONDIP
5 4 3 2 1
ONDIP
5 4 3 2 1
ONDIP
5 4 3 2 1
ONDIP
5 4 3 2 1
6.5x
7.0x
7.5x
ONDIP
5 4 3 2 1
ONDIP
5 4 3 2 1
8.0x
8.5x
ONDIP
5 4 3 2 1
ONDIP
5 4 3 2 1
9.0x
9.5x
ONDIP
5 4 3 2 1
ONDIP
5 4 3 2 1
10.0x
10.5x
ONDIP
5 4 3 2 1
ONDIP
5 4 3 2 1
11.0x
11.5x
ONDIP
5 4 3 2 1
ONDIP
5 4 3 2 1
12.0x
12.5x or
13.0x
6.0x
ONDIP
5 4 3 2 1
ONDIP
5 4 3 2 1
Bus ratio detected by FID (Auto)
Bus ratio selected by SW1 DIP 1-4
SW1 DIP 5 allows
you to enable or disable the "Frequency Ratio Select" function.
14.0x
5 4 3 2 1
ONDIP
*
(Default)
Page 27
27
Chapter 2 Hardware Setup
2-5.4 Processor Core Voltage Select (By SW2 DIP1-DIP6)
• DIP1-DIP6 SW2 allow you to adjust processor core voltage manually. We recommend to leave SW2 DIP1 at default, the default means the
correct processor core voltage is generated according to VID of CPU.
SW2 DIP2 ~ DIP6 SETTING
SW2 DIP1
Auto
(Default)
By DIP 2-6
1.475v
1.550v
1.625v
1.375v
1.325v
1.175v
0.0v
ONDIP
6 5 4 3 2 1
ONDIP
6 5 4 3 2 1
ONDIP
6 5 4 3 2 1
ONDIP
6 5 4 3 2 1
ONDIP
6 5 4 3 2 1
ONDIP
6 5 4 3 2 1
ONDIP
6 5 4 3 2 1
ONDIP
6 5 4 3 2 1
ONDIP
6 5 4 3 2 1
ONDIP
6 5 4 3 2 1
ONDIP
6 5 4 3 2 1
ONDIP
6 5 4 3 2 1
ONDIP
6 5 4 3 2 1
ONDIP
6 5 4 3 2 1
ONDIP
6 5 4 3 2 1
ONDIP
6 5 4 3 2 1
ONDIP
6 5 4 3 2 1
ONDIP
6 5 4 3 2 1
ONDIP
6 5 4 3 2 1
ONDIP
6 5 4 3 2 1
ONDIP
6 5 4 3 2 1
ONDIP
6 5 4 3 2 1
ONDIP
6 5 4 3 2 1
ONDIP
6 5 4 3 2 1
ONDIP
6 5 4 3 2 1
ONDIP
6 5 4 3 2 1
ONDIP
6 5 4 3 2 1
ONDIP
6 5 4 3 2 1
ONDIP
6 5 4 3 2 1
ONDIP
6 5 4 3 2 1
ONDIP
6 5 4 3 2 1
ONDIP
6 5 4 3 2 1
1.450v
1.525v
1.600v
1.675v 1.700v
1.775v
1.850v
1.750v
1.825v
1.400v
1.350v
1.300v
1.250v
1.200v
1.150v
1.100v 1.125v
1.225v
1.275v
1.425v
1.500v
1.575v
1.650v
1.725v
1.800v
ONDIP
6 5 4 3 2 1
ONDIP
6 5 4 3 2 1
(Default)
SW2 DIP 1 allows you to enable or disable "Processor Core Voltage Select" function.
Page 28
28
75DRV/75DRV-X
2-5.5 CPU External Frequency Setting (By SW3)
33.3MHz
200MHz
SW3 CPU EXTERNAL CLOCK PCI CLOCK FSB CLOCK
ON DIP
1 2 3 4 5
30.0MHz
120MHz
240MHz
ON DIP
1 2 3 4 5
33.3MHz
133.3MHz
266MHz
ON DIP
1 2 3 4 5
35.0MHz
140MHz
280MHz
ON DIP
1 2 3 4 5
37.5MHz
150MHz
300MHz
ON DIP
1 2 3 4 5
(Default)
100MHz
IMPORTANT:
• Do figure out the correct processor type by processor’s OPN (Ordering Part Numbers). Correct CPU external frequency is key to ensure reliability of your system.
• Incorrect CPU external frequency or overclocking might cause unstable performance, so we strongly recommend to leave “SW1” at default setting or legal operation.
Page 29
29
Chapter 2 Hardware Setup
2-6 JUMPER SETTING FOR DEVICES ON BOARD
• The following diagrams show the location for jumper blocks on the mainboard.
CAUTION !!
• Do not remove the jumper when power is on. Always make sure the power is off before changing any jumpers. Otherwise, mainboard could be damaged.
• All jumper pins covered with black marks are closed pins.
2-6.1 JP1/JP2 Memory Module Voltage Select
USB2
1
16
1
16
USB3
CNR 1
FLASH BIOS
USB0
USB1
PS/2
MOUSE
PS/2
K/B
LPT1
COM1COM2
GAME/MIDI PORT
MIC
SW1
ON
DIP
5 4 3 2 1
SW2
ON
DIP
6 5 4 3 2 1
CN1
ON
DIP
1 2 3 4 5
SW3
FAN1
1 3
FAN3
1 3
CON1
SAPK RST PLED SLED
HDD/LED IR PWR SUSPEND
++
--
+
-
16 30
1 15
RT2
SCR1
JBAT1
1 3
JP1
JP2
1 3
1 3
WOL1
1 3
4
1
JCD_IN1
1 3
JP17
PCI 1
PCI 2
PCI 3
PCI 4
PCI 5
SSF1
ZD1
DDR 266
AGP PRO 4X
FDC1
IDE1
IDE2
VIA
VT8233
AC'97 Codec
LPC I/O
Controller
VIA
VT8366
Li
Battery
FAN2
1 3
Clock
Generator
FAN4
1 3
LINE
OUT
LINE
IN
JP18
JP19
1 3
1 3
SOCKET A
RT1
VD-¤ TECH
JP10
1 3
13
13
13
13
13
13
JP1
JP2
JP1
JP2
JP1
JP2
2.5V (default)
2.6V
2.7V
This function allows you to select the voltage supplied to the DRAM. The default voltage (2.5V) should be used unless processor overclocking requires a higher voltage.
Memory Module Voltage Select:
NOTE: Using a higher voltage may boost the overclocking performance
but this may result in the shortening of your computer components’s life. It is strongly recommended that you leave the voltage setting default.
Page 30
30
75DRV/75DRV-X
2-6.2 JP17 Power Lost Resume
USB2
1
16116
USB3
CNR 1
FLASH BIOS
USB0
USB1
PS/2
MOUSE
PS/2
K/B
LPT1
COM1COM2
GAME/MIDI PORT
MIC
SW1
ON
DIP
5 4 3 2 1
SW2
ON
DIP
6 5 4 3 2 1
CN1
ON
DIP
1 2 3 4 5
SW3
FAN1
1 3
FAN3
1 3
CON1
SAPK RST PLED SLED
HDD/LED IR PWR SUSPEND
++
--
+
-
16 30
1 15
RT2
SCR1
JBAT1
1 3
JP1
JP2
1 3
1 3
WOL1
1 3
4
1
JCD_IN1
1 3
JP17
PCI 1
PCI 2
PCI 3
PCI 4
PCI 5
SSF1
ZD1
DDR 266
AGP PRO 4X
FDC1
IDE1
IDE2
VIA
VT8233
AC'97 Codec
LPC I/O
Controller
VIA
VT8366
Li
Battery
FAN2
1 3
Clock
Generator
FAN4
1 3
LINE
OUT
LINE
IN
JP18
JP19
1 3
1 3
SOCKET A
RT1
VD-¤ TECH
JP10
1 3
Normal (default)
13
13
JP17
JP17
Enabled
13
13
13
13
13
13
JP18
JP19
JP18
JP19
JP18
JP19
1.5V (default)
1.6V
1.7V
2-6.3 JP18/19 AGP Voltage Select
USB2
1
16116
USB3
CNR 1
FLASH BIOS
USB0
USB1
PS/2
MOUSE
PS/2
K/B
LPT1
COM1COM2
GAME/MIDI PORT
MIC
SW1
ON
DIP
5 4 3 2 1
SW2
ON
DIP
6 5 4 3 2 1
CN1
ON
DIP
1 2 3 4 5
SW3
FAN1
1 3
FAN3
1 3
CON1
SAPK RST PLED SLED
HDD/LED IR PWR SUSPEND
++
--
+
-
16 30
1 15
RT2
SCR1
JBAT1
1 3
JP1
JP2
1 3
1 3
WOL1
1 3
4
1
JCD_IN1
1 3
JP17
PCI 1
PCI 2
PCI 3
PCI 4
PCI 5
SSF1
ZD1
DDR 266
AGP PRO 4X
FDC1
IDE1
IDE2
VIA
VT8233
AC'97 Codec
LPC I/O
Controller
VIA
VT8366
Li
Battery
FAN2
1 3
Clock
Generator
FAN4
1 3
LINE
OUT
LINE
IN
JP18
JP19
1 3
1 3
SOCKET A
RT1
VD-¤ TECH
JP10
1 3
NOTE: This jumper allows user to use the switch of ATX power supply to
control ON/OFF switch directly instead of using the power switch on the mainboard.
Power Lost Resume:
AGP Voltage Select:
Page 31
31
Chapter 2 Hardware Setup
USB2
1
16116
USB3
CNR 1
FLASH BIOS
USB0
USB1
PS/2
MOUSE
PS/2
K/B
LPT1
COM1COM2
GAME/MIDI PORT
MIC
SW1
ON
DIP
5 4 3 2 1
SW2
ON
DIP
6 5 4 3 2 1
CN1
ON
DIP
1 2 3 4 5
SW3
FAN1
1 3
FAN3
1 3
CON1
SAPK RST PLED SLED
HDD/LED IR PWR SUSPEND
++
--
+
-
16 30
1 15
RT2
SCR1
JBAT1
1 3
JP1
JP2
1 3
1 3
WOL1
1 3
4
1
JCD_IN1
1 3
JP17
PCI 1
PCI 2
PCI 3
PCI 4
PCI 5
SSF1
ZD1
DDR 266
AGP PRO 4X
FDC1
IDE1
IDE2
VIA
VT8233
AC'97 Codec
LPC I/O
Controller
VIA
VT8366
Li
Battery
FAN2
1 3
Clock
Generator
FAN4
1 3
LINE
OUT
LINE
IN
JP18
JP19
1 3
1 3
SOCKET A
RT1
VD-¤ TECH
JP10
1 3
Clear CMOS Data
Retain Data (default)
JBAT1
JBAT1
1 3
1 3
2-6.4 JBAT1 For Clear CMOS Data
A battery must be used to retain the mainboard configuration in CMOS RAM.
JBAT1 For Clear CMOS Data:
NOTE: You can clear CMOS by 2-3 pin closed when the system is POWER
OFF. Then, return to 1-2 pin closed position (default). You may damage the mainboard if clearing the CMOS with POWER ON. Unplugging the power cord from power supply before clearing CMOS will be a safest bet for user.
Page 32
32
75DRV/75DRV-X
2-7.1 On Board FAN Connector (FAN1, FAN2, FAN3, FAN4)
CPU FAN1
SYSTEM FAN
CHASSIS FAN
CPU FAN2
FAN4
FAN3
FAN2
FAN1
USB2
1
16116
USB3
CNR 1
FLASH BIOS
USB0
USB1
PS/2
MOUSE
PS/2
K/B
LPT1
COM1COM2
GAME/MIDI PORT
MIC
SW1
ON
DIP
5 4 3 2 1
SW2
ON
DIP
6 5 4 3 2 1
CN1
ON
DIP
1 2 3 4 5
SW3
FAN1
1 3
FAN3
1 3
CON1
SAPK RST PLED SLED
HDD/LED IR PWR SUSPEND
++
--
+
-
16 30
1 15
RT2
SCR1
JBAT1
1 3
JP1
JP2
1 3
1 3
WOL1
1 3
4
1
JCD_IN1
1 3
JP17
PCI 1
PCI 2
PCI 3
PCI 4
PCI 5
SSF1
ZD1
DDR 266
AGP PRO 4X
FDC1
IDE1
IDE2
VIA
VT8233
AC'97 Codec
LPC I/O
Controller
VIA
VT8366
Li
Battery
FAN2
1 3
Clock
Generator
FAN4
1 3
LINE
OUT
LINE
IN
JP18
JP19
1 3
1 3
SOCKET A
RT1
VD-¤ TECH
JP10
1 3
GND +12V SENSOR
On Board FAN Connector (FAN 1:
2-7 CONNECTORS CONFIGURATIONS
• This section lists out all connectors configurations for users’ reference.
On Board FAN Connector (FAN 2):
On Board FAN Connector (FAN 4):
On Board FAN Connector (FAN 3):
These fan connectors support CPU/System chassis cooling fan with +12V. When connecting wire to FAN connectors, users should pay attention that the red wire is for the positive current and should be connected to pin +12V, and the black wire is Ground and should be connected to pin GND. If your mainboard has Hardware Monitor chipset on-board, you must use a specially designed fan with speed sensor to take advantage of this function. For fans with speed sensors, each rotation of the fan blades will send out 2 electric pulses, by which System Hardware Monitor will work out the fan rotation speed by counting the pulses.
NOTE 1: Always consult vendor for proper CPU cooling fan.
NOTE 2: CPU FAN is supported by Hardware Monitor, with a warning
will be given out to high CPU temperature.
Page 33
33
Chapter 2 Hardware Setup
GND
+5V standby
PME
2-7.2 WOL1 Wake On LAN
USB2
1
16116
USB3
CNR 1
FLASH BIOS
USB0
USB1
PS/2
MOUSE
PS/2
K/B
LPT1
COM1COM2
GAME/MIDI PORT
MIC
SW1
ON
DIP
5 4 3 2 1
SW2
ON
DIP
6 5 4 3 2 1
CN1
ON
DIP
1 2 3 4 5
SW3
FAN1
1 3
FAN3
1 3
CON1
SAPK RST PLED SLED
HDD/LED IR PWR SUSPEND
++
--
+
-
16 30
1 15
RT2
SCR1
JBAT1
1 3
JP1
JP2
1 3
1 3
WOL1
1 3
4
1
JCD_IN1
1 3
JP17
PCI 1
PCI 2
PCI 3
PCI 4
PCI 5
SSF1
ZD1
DDR 266
AGP PRO 4X
FDC1
IDE1
IDE2
VIA
VT8233
AC'97 Codec
LPC I/O
Controller
VIA
VT8366
Li
Battery
FAN2
1 3
Clock
Generator
FAN4
1 3
LINE
OUT
LINE
IN
JP18
JP19
1 3
1 3
SOCKET A
RT1
VD-¤ TECH
JP10
1 3
Connect the Wake On LAN signal from LAN card to WOL1
WOL1
This connector connects to a LAN card with a Wake On LAN output. The connector powers up the system when it receives a wake-up packet or signal through the LAN card. This feature requires that Wake On LAN feature is enabled in the BIOS setting called “Power Management Setup” and that your system must be on ATX power supply with at least 720mA / +5V standby power.
Wake On LAN:
2-7.3 CD-ROM Audio Connector (JCD_IN1)
USB2
1
16
1
16
USB3
CNR 1
FLASH BIOS
USB0
USB1
PS/2
MOUSE
PS/2
K/B
LPT1
COM1COM2
GAME/MIDI PORT
MIC
SW1
ON
DIP
5 4 3 2 1
SW2
ON
DIP
6 5 4 3 2 1
CN1
ON
DIP
1 2 3 4 5
SW3
FAN1
1 3
FAN3
1 3
CON1
SAPK RST PLED SLED
HDD/LED IR PWR SUSPEND
++
--
+
-
16 30
1 15
RT2
SCR1
JBAT1
1 3
JP1
JP2
1 3
1 3
WOL1
1 3
4
1
JCD_IN1
1 3
JP17
PCI 1
PCI 2
PCI 3
PCI 4
PCI 5
SSF1
ZD1
DDR 266
AGP PRO 4X
FDC1
IDE1
IDE2
VIA
VT8233
AC'97 Codec
LPC I/O
Controller
VIA
VT8366
Li
Battery
FAN2
1 3
Clock
Generator
FAN4
1 3
LINE
OUT
LINE
IN
JP18
JP19
1 3
1 3
SOCKET A
RT1
VD-¤ TECH
JP10
1 3
PIN NO.
PIN 1
GND
PIN 2
GND
PIN 3
Right Channel
PIN 4
Left Channel
JCD_IN1
4
1
JCD_IN1
CD-ROM Audio Connector:
Page 34
34
75DRV/75DRV-X
2-7.4 Thermal Sensor Connector (RT2)
USB2
1
16116
USB3
CNR 1
FLASH BIOS
USB0
USB1
PS/2
MOUSE
PS/2
K/B
LPT1
COM1COM2
GAME/MIDI PORT
MIC
SW1
ON
DIP
5 4 3 2 1
SW2
ON
DIP
6 5 4 3 2 1
CN1
ON
DIP
1 2 3 4 5
SW3
FAN1
1 3
FAN3
1 3
CON1
SAPK RST PLED SLED
HDD/LED IR PWR SUSPEND
++
--
+
-
16 30
1 15
RT2
SCR1
JBAT1
1 3
JP1
JP2
1 3
1 3
WOL1
1 3
4
1
JCD_IN1
1 3
JP17
PCI 1
PCI 2
PCI 3
PCI 4
PCI 5
SSF1
ZD1
DDR 266
AGP PRO 4X
FDC1
IDE1
IDE2
VIA
VT8233
AC'97 Codec
LPC I/O
Controller
VIA
VT8366
Li
Battery
FAN2
1 3
Clock
Generator
FAN4
1 3
LINE
OUT
LINE
IN
JP18
JP19
1 3
1 3
SOCKET A
RT1
VD-¤ TECH
JP10
1 3
We provide a thermal cable in the mainboard package. This thermal cable is to monitor device which will generates a lot of heat, such as HDD, Graphics card etc. Please connect one end of the thermal cable (A) to mainboard RT2 header, and tape another end of thermal cable (B) on to the device which you want to monitor. After you have finished the thermal cable installation, you will see the detected temperature in BIOS setup
or Hardware monitor utility.
Thermal Sensor Connector (RT2):
RT2
Page 35
35
Chapter 2 Hardware Setup
2-7.5 Complex Header CON1
11
15 15
(+)
(+)
(-)
(-)
(+)
(-)
Logic High
Logic High
SPEAKER SIGNAL
NO CONNECTION
GND
RESET SIGNAL
GND
Vcc
NO CONNECTION
GND
NO CONNECTION
NO CONNECTION
SUSPEND LED SIGNAL
GND
Vcc
Vcc
ATX POWER SWITCH
Vcc
SMI SIGNAL
GND
HDD LED SIGNAL
HDD LED SIGNAL
GND
NO CONNECTION
INFRARED TRANSMIT SIGNAL
INFRARED TRANSMIT SIGNAL
1st HDD LED
2nd HDD LED
INFRARED(IR)
POWER SWITCH
SMI
SPEAKER
RESET SWITCH
POWER LED
NO CONNECTION
SUSPEND LED
CON1
1
2
3
4
4
5
6
7
8
6
• This complex Header consists of 9 connectors providing various supports:
1. SMI Connector (System Management Interrupt): CONNECTION: This 2-pin connector is connected to the case-mounted
Suspend Switch or to the “Turbo Switch”. FUNCTION: Manually placing the system into a Suspend mode or “Green” mode.
2. Power Switch Connector: CONNECTION: Connected to a momentary button or switch. FUNCTION: Manually switching the system between “On” and “Soft Off”.
Pressing the momentary button for more than 4 seconds will also turn the system off.
3. IR Connector (Infrared Connector): CONNECTION: Connected to Connector IR on board. FUNCTION: Supporting wireless transmitting and receiving module on
board.
4. 1st HDD LED Connector / J2 2nd HDD LED Connector: CONNECTION: Connected to HDD LED. FUNCTION: To supply power to HDD LED.
5. Suspend LED Connector: CONNECTION: Connected to Suspend indicator. FUNCTION: To supply power to “Suspend indicator”.
Page 36
36
75DRV/75DRV-X
2-7.6 ATX Power Supply Connector
• This connector connects to an ATX power supply. The plug from the power supply should only be inserted to ATX Power connector in a specific orientation. Find the proper orientation and push it down firmly to make sure that all pins are aligned.
• Your power supply should support at least 10mA on the 5V standby voltage. It may cause difficulty to turn on the system power if the power supply does not support the load.
• For Wake On LAN function, the power supply should support at least 720mA current.
VCC VCC
-5V GND GND GND Power Supply on GND
-12V VCC3
+12V
+5V Standby
Power Good
GND
VCC
GND
VCC
GND VCC3 VCC3
6. Power LED Connector: CONNECTION: Connected to System Power LED. FUNCTION: To supply power to “System Power LED”.
7. Reset Switch Connector: CONNECTION: Connected to the case-mounted “Reset Switch”. FUNCTION: To supply power to “Reset Switch” and support system
reboot function.
8. Speaker Connector: CONNECTION: Connected to the case-mounted Speaker. FUNCTION: To supply power to the case-mounted Speaker.
Page 37
37
Chapter 2 Hardware Setup
2-7.7 Chassis Panel Connector
A.
E. F. G. H. I. J. K.
B. C. D.
A : PS/2 MOUSE PORT B : USB 0 PORT C : LPT1 PORT D : GAME/MIDI PORT E : PS/2 KEYBOARD PORT F : USB 1 PORT G : COM 1 PORT H : COM 2 PORT I : LINE OUT / SPEAKER OUT PORT J : LINE IN K : MICROPHONE
Page 38
38
75DRV/75DRV-X
USB2
1
16
1
16
USB3
CNR 1
FLASH BIOS
USB0
USB1
PS/2
MOUSE
PS/2
K/B
LPT1
COM1COM2
GAME/MIDI PORT
MIC
SW1
ON
DIP
5 4 3 2 1
SW2
ON
DIP
6 5 4 3 2 1
CN1
ON
DIP
1 2 3 4 5
SW3
FAN1
1 3
FAN3
1 3
CON1
SAPK RST PLED SLED
HDD/LED IR PWR SUSPEND
++
--
+
-
16 30
1 15
RT2
SCR1
JBAT1
1 3
JP1
JP2
1 3
1 3
WOL1
1 3
4
1
JCD_IN1
1 3
JP17
PCI 1
PCI 2
PCI 3
PCI 4
PCI 5
SSF1
ZD1
DDR 266
AGP PRO 4X
FDC1
IDE1
IDE2
VIA
VT8233
AC'97
Codec
LPC I/O
Controller
VIA
VT8366
Li
Battery
FAN2
1 3
Clock
Generator
FAN4
1 3
LINE
OUT
LINE
IN
JP18
JP19
1 3
1 3
SOCKET A
RT1
VD-¤ TECH
JP10
1 3
SCR1 pin assignment
14
1
VCC
LED
RFU
SCRIO
RFU
NC
NC
SCRFET#
SCRPRES#
SCRREST
NCNCSCRCLK GND
2-7.8 Smart Card Reader Connector (SCR1)
• The connector “SCR1” allows you to use Smart Card Reader. It is compliant with Personal Computer Smart Card (PC/SC) working group standard and smart card (ISO 7816) protocols.
Page 39
39
Chapter 2 Hardware Setup
USB2
1
16
1
16
USB3
CNR 1
FLASH BIOS
USB0
USB1
PS/2
MOUSE
PS/2
K/B
LPT1
COM1COM2
GAME/MIDI PORT
MIC
SW1
ON
DIP
5 4 3 2 1
SW2
ON
DIP
6 5 4 3 2 1
CN1
ON
DIP
1 2 3 4 5
SW3
FAN1
1 3
FAN3
1 3
CON1
SAPK RST PLED SLED
HDD/LED IR PWR SUSPEND
++
--
+
-
16 30
1 15
RT2
SCR1
JBAT1
1 3
JP1
JP2
1 3
1 3
WOL1
1 3
4
1
JCD_IN1
1 3
JP17
PCI 1
PCI 2
PCI 3
PCI 4
PCI 5
SSF1
ZD1
DDR 266
AGP PRO 4X
FDC1
IDE1
IDE2
VIA
VT8233
AC'97 Codec
LPC I/O
Controller
VIA
VT8366
Li
Battery
FAN2
1 3
Clock
Generator
FAN4
1 3
LINE
OUT
LINE
IN
JP18
JP19
1 3
1 3
SOCKET A
RT1
VD-¤ TECH
JP10
1 3
2-7.9 Communication And Networking Riser Slot (CNR)
• This connector allows you to use network, modem or audio riser cards.
Note:
1. If modem CNR is installed, the modem CNR must be set as primary.
2. Only one LAN CNR can be supported.
3. The audio CNR must be set as secondary, if on-chip AC 97 is enabled.
4. CNR devices are not provided with this mainboard.
CNR slot
Page 40
40
75DRV/75DRV-X
PIN 6 : None PIN 5 : Mouse Clock PIN 4 : Vcc PIN 3 : GND PIN 2 : None PIN 1 : Mouse Data
PS/2 MOUSE
PIN 6 : None PIN 5 : Keyboard Clock PIN 4 : Vcc PIN 3 : GND PIN 2 : None PIN 1 : Keyboard Data
PS/2 KEYBOARD
• When plugging the USB cable into USB2/USB3 HEADER, users must make sure the red wire is connected to the first pin.
1
16
Red VCC
Green
DO+
Green
DO+
White
DO-
White
DO-
Black
GND
Black
GND
Red VCC
GND Black
GND Black
USB 2 / USB3 Header
1
16
USB 2 / USB 3 Header
1
Additional USB Cable (Optional)
red wire
2-7.10 USB Header (USB2/USB3 Header)
• This header is for connecting the additional USB cable to provides you additional two USB ports. User can order the additional USB cable from your mainboard dealer and vender.
2-7.11 PS/2 Mouse And PS/2 Keyboard
Page 41
41
Chapter 2 Hardware Setup
2-8 VOICE DIAGNOSTIC FUNCTION FOR 75DRV-X ONLY
• A Voice Diagnostic Function is incorporated in “Advanced BIOS Features” of the “Award BIOS Setup” as “VD-Tech II Function”. With this function enabled in “Advanced BIOS Features”, it will voice out the problems or conflicts whenever user configures the components or boots up the PC system.
• The voice can be in chinese or English, depending on the setting of Jumper JP10. Change the setting of JP10 will change the language of the voice.
1. The Processor might be damaged or not installed properly.
2. The memory module might be damaged or not installed properly.
3. The VGA card might be damaged or not installed properly.
4. The IDE cable might be damaged or not installed properly.
5. Please clear CMOS setting.
6. System available.
Page 42
42
75DRV/75DRV-X
2-8.1 JP10 VD-Tech II Language Select
Voice Diagnostic Language Select:
USB2
1
16116
USB3
CNR 1
FLASH BIOS
USB0
USB1
PS/2
MOUSE
PS/2
K/B
LPT1
COM1COM2
GAME/MIDI PORT
MIC
SW1
ON
DIP
5 4 3 2 1
SW2
ON
DIP
6 5 4 3 2 1
CN1
ON
DIP
1 2 3 4 5
SW3
FAN1
1 3
FAN3
1 3
CON1
SAPK RST PLED SLED
HDD/LED IR PWR SUSPEND
++
--
+
-
16 30
1 15
RT2
SCR1
JBAT1
1 3
JP1
JP2
1 3
1 3
WOL1
1 3
4
1
JCD_IN1
1 3
JP17
PCI 1
PCI 2
PCI 3
PCI 4
PCI 5
SSF1
ZD1
DDR 266
AGP PRO 4X
FDC1
IDE1
IDE2
VIA
VT8233
AC'97 Codec
LPC I/O
Controller
VIA
VT8366
Li
Battery
FAN2
1 3
Clock
Generator
FAN4
1 3
LINE
OUT
LINE
IN
JP18
JP19
1 3
1 3
SOCKET A
RT1
VD-¤ TECH
JP10
1 3
With “VD-Tech II Function” enabled in “Advanced BIOS Features” of Award BIOS Setup, you can choose either Chinese or English as the language of the VD-Tech II Function.
English (default)
1 3
JP10
1 3
JP10
Chinese
Page 43
43
Chapter 2 Hardware Setup
MEMO
MEM
O
Page 44
44
75DRV/75DRV-X
CHAPTER 3
SOFTWARE SETUP
3-1 VIA CHIPSET DRIVER INSTALLATION (4-IN-1 DRIVER) 3-2 HARDWARE MONITOR INSTALLATION 3-3 AC’97 AUDIO CODEC INSTALLATION
ABOUT SUPPORT CD
• In Support CD, it contains most informations for user’s requirement, such as Acrobat Reader, BIOS, User’s full version Manual, Driver, Hardware Monitor (if mainboard supports this function), Patch, and Utilities etc. User can browse the CD and get further details in regard of our mainboard. Of course, welcome to vendor’s website for the newest release.
This chapter contains the following topics :
Page 45
45
Chapter 3 Software Setup
3-1 VIA CHIPSET DRIVER INSTALLATION (4-IN-1 DRIVER)
• Click on the “Install via 4-in-1 driver” to continue.
5
• “VIA Service Pack README” screen will appear, please click the “Yes” button to continue.
7
Yes
• Click on the “VIA Chipset Driver(2)”.
3
• Click on the “4-in-1 driver”.
4
• Please put the Support CD provided in your mainboard package into the CD-ROM drive.
1
• When a welcome window appears on the screen, users should choose “Install Driver”.
2
• When the welcome screen appears, press “Next” button to continue.
6
Next
Page 46
46
75DRV/75DRV-X
Bus Master PCI IDE Driver AGP VxD Driver VIA Chipset Function’s Registry IRQ Routing Miniport Driver
• Press select the checkbox as below:
8
Next
Note: For user who are upgrading VIA Drivers, we recommend to install
the 4-in-1 as it will automatically detect and update the necessary drivers.
• Click on “Click to enable DMA Mode” checkbox to
enable DMA function, then click the “Next” button to continue.
10
Next
• Select “Install VIA ATAPI Vendor Support Driver”
checkbox, then click the “Next” button to continue.
9
Next
Page 47
47
Chapter 3 Software Setup
11
• Select “Install VIA AGP VxD” in turbo mode and press Next button to continue.
Next
• Select “Install VIA IRQ Routing Miniport Driver”
checkbox, then click the “Next” button to continue.
12
Next
• After all these setup proce­ dures have finished, please restart your computer by clicking on “Finish”.
13
Finish
Page 48
48
75DRV/75DRV-X
3-2 HARDWARE MONITOR INSTALLATION
• Please put the Support CD provided in your mainboard package into the CD-ROM drive.
1
• When a welcome window appears on the screen, users should choose “Install Driver”.
2
• Click on the “Hardware Monitor Utility”.
4
• Click on the “VIA Chipset Driver(2)”.
3
• After which Follow the instruction on screen to complete the installation.
7
Install
• When “Exploring-ITE 8705” window appears, please click on the file “Install”.
6
• Click on the “Explore CD” or user can install it through directory CD-ROM \hardware monitor utility\ITE\install.exe.
5
Page 49
49
Chapter 3 Software Setup
• Click on the “OK” button.
8
OK
• The following screen shows the ITE SMARTGUARDIAM, which shows the information about system temperatures, voltages and Fan speed. You can also change some Value settings for your system to optimize its performance.
9
Page 50
50
75DRV/75DRV-X
3-3 AC’97 AUDIO CODEC DRIVER INSTALLATION
• Please put the Support CD provided in your mainboard package into the CD-ROM drive.
1
• When a welcome window appears on the screen, users should choose “Install Driver”.
2
Next
• Press “Next” button to continue.
5
• When asking you install or remove the audio driver, please select “Install” and press “Next” button to continue.
6
Next
7
• After all the setup process is finished, please restart your computer by clicking on
“Finish”.
Finish
• Click on the “VIA Chipset Driver(2)”.
3
• Click on the “AC’97 driver”.
4
Page 51
51
Chapter 3 Software Setup
MEMO
MEM
O
Page 52
75DRV/75DRV-X
52
CHAPTER 4
BIOS SETUP
4-1 WHAT IS BIOS SETUP 4-2 HOW TO RUN BIOS SETUP 4-3 WHAT IS CMOS 4-4 WHAT IS POST 4-5 BIOS UPGRADE 4-6 BIOS SETUP
THE BIOS
• BIOS stands for Basic Input and Output System. It is sometimes called ROM BIOS because it is stored in a Read-Only Memory(ROM) chip on the mainboard. BIOS is the first program to run when you turn on your computer.
• BIOS performs the following functions:
1. Initializing and testing hardware in your computer (a process called “POST”, for Power On Self Test).
2. Loading and running your operating system.
3. Helping your operating system and application programs to manage your PC hardware by means of a set of routines called BIOS Run-Time Service.
This chapter contains the following topics :
Page 53
Chapter 4 BIOS Setup
53
4-1 WHAT IS BIOS SETUP
• BIOS setup is an interactive BIOS program that you need to run when:
1. Changing the hardware of your system. (For example: installing a new Hard Disk etc.)
2. Modifying the behavior of your computer. (For example: changing the system time or date, or turning special features on or off etc.)
3. Enhancing your computer’s behavior. (For example: speeding up perfor­ mance by turning on shadowing or cache)
4-2 HOW TO RUN BIOS SETUP
• To access BIOS setup menu, press < DEL > key after “POST”, and before the OS is loaded. The BIOS usually display the following message:
Press DEL to enter SETUP
4-3 WHAT IS CMOS
• CMOS is the memory maintained by a battery. The BIOS uses CMOS to store the settings you have selected in SETUP. The CMOS also maintains the internal clock. Every time you turn on your computer, the BIOS Looks into CMOS for the settings you have selected and configures your computer accordingly. If the battery is out of power, the CMOS data will be lost and POST will issue a “CMOS invalid” or “CMOS checksum invalid” message. If this happens, you have to replace the battery and do some proper settings in SETUP.
4-4 WHAT IS POST
• POST is an acronym for Power On Self Test. POST will test all things the BIOS does before the operating system is started. Each of POST routines is assigned a POST code, a unique number which is sent to I/O port 080h before the routine is executed.
4-5 BIOS UPGRADE
• System BIOS is incorporated into a Flash memory component of the mainboard. Flash BIOS allows user to upgrade BIOS without the need to replace an EPROM component.
Page 54
75DRV/75DRV-X
54
• The upgrade utility can be loaded on a floppy diskette and used to provides the capability to save, verify, and update the system BIOS. The upgrade utility can be run from a hard disk drive or a network drive.
4-5.1 BEFORE UPGRADING BIOS
• It is highly recommended that you save a copy of the original mainboard BIOS along with a Flash EPROM Programming utility (AWDFLASH.EXE) to a bootable floppy disk in case you need to reinstall the BIOS later.
4-5.2 UPGRADE PROCESS
“AWDFLASH.EXE” is a Flash EPROM Programming utility that updates the BIOS by uploading a new BIOS file to the programmable flash ROM on the mainboard, This program only works in DOS environment only, the utility
can not be executed in win95/98, ME, NT or WINDOWS 2000 environment.
Upgrading the system BIOS
Step 1. Please visit the board maker’s website, download latest BIOS file and award flash utility “AWDFLASH.EXE”. The BIOS file format will be *.bin, of which “*” stands for the specific file name.
Step 2. Create a bootable diskette. Then copy the BIOS file and award flash utility “AWDFLASH.EXE” into the diskette.
Step 3. Insert the diskette into drive A, reboot your system and boot form the diskette.
Note: Normally, to upgrade BIOS is unnecessary if the system is working
fine without any problem. Users should not upgrade the BIOS unless you experience incompatible problems or need to create new features. However, please read all information in this section before upgrading.
Page 55
Chapter 4 BIOS Setup
55
Step 4. Type awdflash *.bin /sn/py/cc and then press <Enter> to run BIOS upgrade program. (*.bin depends on your mainboard model and version code. Instead of typing “*”, you should type specific file name for your specific mainboard).
Step 5. Please press <F1> or <F10> to exit or reset your system, Warning ! If the message “Write Fail” appears while Award “FLASH MEMORY WRITER” is verifying Flash memory, just repeat the process. Please DO NOT reset or turn off the system. If the award memory flash utility is not able to update the BIOS successfully, your system may not be able to boot up.
Step 6. You will need a message “CMOS checksum error-Default loaded” during booting the system. Press <Del> to run CMOS setup utility, then reload “LOAD SETUP DEFAULTS” or “Load Optimized Defaults” and save
this change.
Page 56
75DRV/75DRV-X
56
Award Flash Memory Writer Start Screen
Award Flash Memory Writer Complete Screen
Page 57
Chapter 4 BIOS Setup
57
The parameters of AWDFLASH.EXE
/sn: No original BIOS backup /py: Program flash memory /cc: Clear CMOS data (and update data automatically) after pro­ gramming
NOTE: Users can type AWDFLASH /? to get further details about the
parameters. Incorrect usage of the parameter will damage the BIOS information, so we strongly recommend user to leave parameters alone unless you fully understand their function.
Page 58
75DRV/75DRV-X
58
4-6 BIOS SETUP --- CMOS SETUP UTILITY
• This mainboard comes with the AWARD BIOS from AWARD Software Inc. Enter the CMOS Setup Utility Main Menu by:
1. Turn on or reboot your system. After a series of diagnostic checks, the following message will appear:
PRESS <DEL> TO ENTER SETUP
2. Press the <DEL> key and the main program screen will appear as follows.
3. Use the arrow keys on your keyboard to select an option, and press
<Enter>. Modify the system parameters to reflect the options installed in your system.
4. You may return to the Main Menu anytime by pressing <ESC>.
5. In the Main Menu, “SAVE AND EXIT SETUP” saves your changes and
reboots the system, and “EXIT WITHOUT SAVING” ignores your changes and exits the program.
4-6.1 CMOS SETUP UTILITY
Time, Date, Hard Disk Type...
CMOS Setup Utility - Copyright (C) 1984 - 2001 Award Software
Standard CMOS Features
Advanced BIOS Features
Advanced Chipset Features
Integrated Peripherals
Power Management Setup
PnP/PCI Configurations
SmartDoc Anti-Burn shield
Frequeny/Voltage Control
Load Optimized Defaults
Set Supervisor Password
Set User Password
SAVE & EXIT SETUP
EXIT WITHOUT SAVING
Esc : Quit F10 : Save & Exit Setup
: Select Item
Page 59
Chapter 4 BIOS Setup
59
• Standard CMOS Setup records some basic system hardware configuration
and sets the system clock and error handling. You only need to modify the configuration values of this option if you want to change your system hard­ ware configuration or when the data stored in the CMOS memory gets lost or damaged.
Run the STANDARD CMOS SETUP as follows:
1. Choose “STANDARD CMOS SETUP” from the Main Menu and a screen
with a list of options will appear:
2. Use one of the arrow keys to move between options and modify the
selected options by using PgUp / PgDn / + / - keys.
4-6.2 STANDARD CMOS SETUP
Date (mm:dd:yy) Mon, January 15 2001 Time (hh:mm:ss) 9 : 52 : 15
IDE Primary Master None IDE Primary Slave CREATIVEDVD1240E IDE Secondary Master IBM-DTLA-307045 IDE Secondary Slave None
Drive A 1.44M, 3.5 in Drive B None
Video EGA/VGA Halt On All,But Keyboard
Base Memory 640K Extended Memory 31744K Total Memory 32768K
Item Help
Menu Level
CMOS Setup Utility - Copyright (C) 1984-2001 Award Software
Standard CMOS Features
:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults
Page 60
75DRV/75DRV-X
60
Primary / Secondary
Master / Slave
This field records the specifications for all non-SCSI hard disk drives installed in your system. Refer to the respective documentation on how to install the drives.
Time (hh:mm:ss) The time format is based on the 24-hour military-time
clock. For example, 1 p.m. is 13:00:00. Press the left or right arrow key to move to desired field. Press the PgUp or PgDn key to increment the setting, or type the desired value into the field.
Date (mm:dd:yy) The BIOS determines the day of the week from the
other date information. This field is for information only. Press the left or right arrow key to move to the desired field (date, month, year). Press the PgUp or PgDn key to increment the setting, or type the desired value into the field.
IDE HDD Auto-Detection Press Enter
IDE Primary Master Auto Access Mode  Auto
Capacity 13022 MB
Cylinder 25232 Head 16 Precomp 0 Landing Zone 25231 Sector 63
Item Help
Menu Level
CMOS Setup Utility - Copyright (C) 1984-2001 Award Software
IDE Primary Master
:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults
Page 61
Chapter 4 BIOS Setup
61
3. Press <ESC> to return to the Main Menu when you finish setting up all
items.
Base Memory Typically 640KB. Also called conventional memory.
The DOS operating system and conventional appli­cations use this area.
Extended Memory Above the 1MB boundary. Early IBM personal
computers could not use memory above 1MB, but current PCs and their software can use extended memory.
Total Memory This option shows system memory capacity.
Drive A / Drive B Select this field to the type(s) of floppy disk drive(s)
installed in your system. The choices are: 360KB, 5.25in;
1.2MB, 5.25in; 720KB, 3.5in;
1.44MB, 3.5in;
2.88MB, 3.5in; None.
Video Select the type of primary video subsystem in your
computer. The BIOS usually detects the correct video type automatically. The BIOS supports a secondary video subsystem, but you do not select it in setup.
Halt On During the power-on self-test (POST), the computer
stops if the BIOS detects a hardware error. You can tell the BIOS to ignore certain errors during POST and continue the boot-up process.
Page 62
75DRV/75DRV-X
62
VD-Tech II Virus Warning CPU Internal Cache External Cache CPU L2 Cache ECC Checking Quick Power On Self Test First Boot Device Second Boot Device Third Boot Device Boot Other Device Swap Floppy Drive Boot Up Floppy Seek Boot Up NumLock Status Gate A20 Option Typematic Rate Setting Typematic Rate (Chars/Sec) Typematic Delay (Msec) Security Option OS Select For DRAM > 64MB Video BIOS Shadow
Item Help
CMOS Setup Utility - Copyright (C) 1984-2001 Award Software
Advanced BIOS Features
:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults
Menu Level
Enabled Disabled Enabled Enabled Enabled Enabled CDROM HDD-0 LS120 Enabled Disabled Disabled On Fast Disabled 6 250 Setup Non-OS2 Enabled
4-6.3 ADVANCED BIOS FEATURES
• ADVANCED BIOS FEATURES improves your system performance or sets
up system features according to your preference.
Run the ADVANCED BIOS FEATURES as follows:
1. Choose “ADVANCED BIOS FEATURES” from the Main Menu and a
screen with a list of options will appear:
Page 63
Chapter 4 BIOS Setup
63
2. Use one of the arrow keys to move between options and modify the
selected options by using PgUp / PgDn / + / - keys. An explanation of the <F> keys follows:
<F1>: “Help” gives options available for each item. <F5>: Get the previous values. These values are the values with which the
user starts the current session. <F6>: Load all options with the BIOS default values. <F7>: Load all options with the Setup default values.
CPU Internal Cache/
External Cache
Cache memory is additional memory that is much faster than conventional DRAM (system memory). CPUs from 486-type up contain internal cache memory, and most, but not all, modern PCs have additional (external) cache memory. When the CPU requests data, the system transfers the requested data from the main DRAM into cache memory, for faster access by the CPU.
Virus Warning When enabled, you receive a warning message if a
program (specifically, a virus) attempts to write to the boot sector or the partition table of the hard disk drive. You should then run an antivirus program. Keep in mind that this feature protects only the boot sector, not the entire hard drive.
NOTE: Many disk diagnostic programs that access the boot sector table
can trigger the virus warning message. If you plan to run such a program, we recommend that you disable the virus warning.
VD-Tech II This item allows users to enabled or disabled Voice
Diagnostic function.
Page 64
75DRV/75DRV-X
64
Boot Up NumLock
Status
Toggle between On or Off to control the state of the NumLock key when the system boots. If On, the numeric keypad is in numeric mode. If off, the numeric keypad is in cursor control mode.
Gate A20 Option Gate A20 refers to the way the system addresses
memory above 1 MB (extended memory). When set to Fast, the system chipset controls Gate A20. When set to Normal, a pin in the keyboard control­ler controls Gate A20. Setting Gate A20 to Fast improves system speed, particularly with OS/2 and Windows.
Boot Up Floppy Seek When enabled, the BIOS tests (seeks) floppy drives
to determine whether they have 40 or 80 tracks. Only 360-KB floppy drives have 40 tracks; drives with 270KB, 1.2MB, and 1.44MB capacity all have 80 tracks. Because very few modern PCs have 40-track floppy drives, we recommend that you set this field to a disabled to save time.
Swap Floppy Drive When enabled, floppy drives A and B will be exchanging
without any physical connection and modification on the cables.
Quick Power On Self
Test
Select Enabled to reduce the amount of time required to run the power-on self-test (POST). A quick POST skips certain steps. We recommend that you normally enable quick POST.
First/Second/Third/
Other Boot Device
The BIOS attempts to load the operating system from the devices in the sequence selected in these items. The choices: Floppy; LS/ZIP; HDD; SCSI; CDROM; Disabled.
CPU L2 Cache ECC
Checking
When you select Enabled, it will speed up memory checking when the external cache contains ECC SRAMs. The choices: Enabled; Disabled.
Page 65
Chapter 4 BIOS Setup
65
Typematic Rate Setting When Disabled, the following two items (Typematic Rate
and Typematic Delay) are irrelevant. Keystroke repeats at a rate determined by the keyboard controller in your system. When Enabled, you can select a typematic rate and typematic delay.
Typematic Rate (Chars
/ Sec)
When the typematic rate setting is enabled, you can select a typematic rate (the rate at which character repeats when you hold down a key) of 6, 8, 10, 12, 15, 20, 24, or 30 characters per second.
OS Select For DRAM >
64MB
Select OS2 only if you are running OS/2 operating system with greater than 64MB of RAM on your system.
Security Option If you have set a password, select whether the
password is required every time the System boots, or only when you enter setup. The choices: system; setup.
Video BIOS Shadow Performance will be improved by copying Video
BIOS to Shadow RAM.
Typematic Delay
(Msec)
Choices: 250; 500; 750; 1000. This option sets the time interval for displaying the first and the second characters. If enabled, the time interval is optional.
3. Press <ESC> to return to the Main Menu when you finish setting up all
items.
Page 66
75DRV/75DRV-X
66
• ADVANCED CHIPSET FEATURES is used to modify the values of chipset buffers. These buffers control the system options.
Run the ADVANCED CHIPSET FEATURES as follows:
1. Choose “ADVANCED CHIPSET FEATURES” from the Main Menu and a list of option will appear:
2. Use one of the arrow keys to move between options and modify the
selected options by using PgUp / PgDn / + / - keys. An explanation of the <F> keys follows:
<F1>: “Help” gives options available for each item. <F5>: Get the previous values. These values are the values with which the user starts the current session. <F6>: Load all options with the BIOS default values. <F7>: Load all options with the Setup default values.
4-6.4 ADVANCED CHIPSET FEATURES
DRAM Colck/Drive Control AGP & P2P Bridge Control CPU & PCI Bus Control Memory Hole System BIOS Cacheable Video RAM Cacheable
Item Help
Menu Level
CMOS Setup Utility - Copyright (C) 1984-2001 Award Software
Advanced Chipset Features
:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults
Press Enter Press Enter Press Enter Disabled Disabled Disabled
Page 67
Chapter 4 BIOS Setup
67
* Current FSB Fre-
quency
This item allows you to control the FSB Frequency.
DRAM CLOCK/DRIVE CONTROL
Current FSB Frequency DRAM Clock DRAM Timing SDRAM Cycle Length Bank Interleave DRAM Command Rate
Item Help
Menu Level
CMOS Setup Utility - Copyright (C) 1984-2001 Award Software
DRAM Clock/Drive Control
:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults
100MHz 100MHz By SPD
2.5 Disabled 1T Command
* DRAM Clock The value represents the performance parameters
of the installed memory chips (DRAM). Do not change the value from the factory setting unless you install new memory that has a different performance rating.
* DRAM Timing When this item Enabled, DRAM Timing is set by
SPD. SPD (Serial Presence Detect) is located on the memory modules, BIOS reads information coded in SPD during system boot up.
* SDRAM Cycle Length Select CAS latency time in HCLKs of 2 or 3. The
system designer already set the values. Do not change the default value unless you change speci­fications of the installed DRAM or the installed CPU.
* Bank Interleave
The choices: Disabled; 2 Bank; 4 Bank.
Page 68
75DRV/75DRV-X
68
* AGP Aperture Size Series of options are available: 4, 8, 16, 32, 64, 128
or 256 MB. Memory mapped and graphics data structures can reside in a Graphics Aperture. This area is like a linear buffer. BIOS will automatically report the starting address of this buffer to the O.S. The default setting is 64MB.
* AGP Driving Control This item allows you to adjust the AGP driving force.
Choose Manual to key in a AGP Driving Value in the next selection. This field is recommended to set in Auto for avoiding any error in your system. The choice: Manual, Auto.
* AGP Mode This item allows you to select AGP Mode.
The choice: 1x, 2x, 4x.
AGP & P2P BRIDGE CONTROL
AGP Aperture Size AGP Mode AGP Driving Control AGP Driving Value AGP Fast Write AGP Master 1 WS Write AGP Master 1 WS Read
Item Help
Menu Level
CMOS Setup Utility - Copyright (C) 1984-2001 Award Software
AGP & P2P Bridge Control
:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults
64M 4X Auto DA Disabled Disabled Disabled
* DRAM Command
Rate
The choices: Disabled; 2 Bank; 4 Bank.
Page 69
Chapter 4 BIOS Setup
69
* AGP Driving Value This item allows you to adjust the AGP driving force.
The choice: Min=0000 ~ Max=00FF.
* AGP Fast Write This item will enable the AGP model into fast write
mode. If your graphics card does not support this function, please do not enable this function.
* AGP Master 1 ws
write
Leave this field at default.
* AGP Master 1 ws
read
Leave this field at default.
CPU & PCI BUS CONTROL
* PCI1 Master 0 WS
Write
When Enabled, writes to the PCI bus are executed with zero wait states. The choice: Enabled, Disabled.
PCI1 Master 0 WS Writer PCI2 Master 0 WS Write PCI1 Post Write PCI2 Post Write PCI Delay Transaction
Item Help
Menu Level
CMOS Setup Utility - Copyright (C) 1984-2001 Award Software
CPU & PCI Bus Control
:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults
Enabled Enabled Enabled Enabled Disabled
* PCI2 Master 0 WS
Write
Leave this field at default.
Page 70
75DRV/75DRV-X
70
3. Press <ESC> to return to the Main Menu when you finish setting up all
items.
System BIOS
Cacheable
Selecting Enabled allows caching of the system BIOS ROM at F0000h-FFFFFh, resulting in better system performance.
Video RAM Cacheable Selecting Enabled allows caching of the video memory
(RAM) at A0000h-AFFFFh, resulting in better video performance. However, check your AGP manual to find out if any compatibility problem exists.
Memory Hole In order to improve performance, certain space in
memory is reserved for ISA cards. This memory must be mapped into the memory space below 16MB. The choices: 15M-16M; Disabled.
* PCI Delay Transac-
tion
Leave this field at default.
* PCI2 Post Write Leave this field at default.
* PCI1 Post Write Leave this field at default.
Page 71
Chapter 4 BIOS Setup
71
• INTEGRATED PERIPHERALS option allows you to get some information inside your system when it is working.
Run the INTEGRATED PERIPHERALS as follows:
1. Choose “INTEGRATED PERIPHERALS” from the Main Menu and a list
of options will appear:
2. Use one of the arrow keys to move between options and modify the
selected options by using PgUp / PgDn / + / - keys. An explanation of the <F> keys follows:
<F1>: “Help” gives options available for each item. <F5>: Get the previous values. These values are the values with which the
user starts the current session. <F6>: Load all options with the BIOS default values. <F7>: Load all options with the Setup default values.
4-6.5 INTEGRATED PERIPHERALS
Item Help
Menu Level
VIA OnChip IDE Device VIA OnChip PCI Device VIA SuperIO Device Init Display First OnChip USB Controller USB keyboard Support IDE HDD Block Mode
CMOS Setup Utility - Copyright (C) 1984-2001 Award Software
Integrated Peripherals
:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults
Press Enter Press Enter Press Enter PCI Slot All Enabled Disabled Enabled
Page 72
75DRV/75DRV-X
72
* Primary
Master / Slave PIO
Secondary
Master / Slave PIO
Choose Auto or Mode 0~4. The BIOS will detect the HDD mode type automatically when you choose Auto. You need to set to a lower mode than Auto when your hard disk becomes unstable. The choices: Auto; Mode 0; Mode 1; Mode 2; Mode 3; Mode 4.
* On-Chip IDE channel
0/1
The chipset contains a PCI IDE interface with support from two IDE channels. Select Enabled to activate the first and/or the second IDE interface. Select Disabled to inactivate an inter­face if you install a primary and/or second add­on IDE interface. The choices: Enabled; Disabled.
VIA ONCHIP IDE DEVICE
* IDE Prefetch Mode The on-board IDE drive supports IDE perfecting for
faster drive accesses. If the IDE device doesn’t sup­port perfecting, set this field to Disabled. The choices: Enabled; Disabled.
Item Help
Menu Level
OnChip IDE Channel0 OnChip IDE Channel1 IDE Prefetch Mode Primary Master PIO Primary Slave PIO Secondary Master PIO Secondary Slave PIO Primary Master UDMA Primary Slave UDMA Secondary Master UDMA Secondary Slave UDMA
CMOS Setup Utility - Copyright (C) 1984-2001 Award Software
VIA OnChip IDE Device
:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults
Enabled Enabled Enabled Auto Auto Auto Auto Auto Auto Auto Auto
Page 73
Chapter 4 BIOS Setup
73
* Primary
Master / Slave UDMA
Secondary
Master / Slave UDMA
Ultra DMA33/66/100 implementation is possible only if your IDE hard drive supports it, if the operating environment includes a DMA drive, and if your sys­tem software both support Ultra DMA33/66/100. Select “Auto” to enable BIOS support. The choices: Auto; Disabled.
VIA ONCHIP PCI DEVICE
* VIA-3058 AC’97
Audio
Select “Disabled” to use the on-chip audio capability of your system. Most of the field do not appear when this field is “Disabled”, for user who wants to use add-on sound card, this tiled must be disabled.
* VIA-3068 MC97
Modem
This option allows you to decide to enable/disable the Onchip Modem. The choices: Auto; Disabled.
VIA-3058 AC'97 Audio VIA-3068 MC97 Modem
Item Help
Menu Level
CMOS Setup Utility - Copyright (C) 1984-2001 Award Software
VIA OnChip PCI Device
:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults
Disabled Auto
Page 74
75DRV/75DRV-X
74
* Onboard Serial
Port 1 / Port 2
Select a logical COM port name and matching address for the first and second serial ports. Select an address and corresponding interrupt for the first and second serial ports.
* UART Mode Select The second serial port on your system may offer
a variety of infrared port modes. Click here for a description of various modes. (Click your browser’s Back button, or your right mouse button, to return to this page.) The choices: Standard; HPSIR; ASKIR
VIA SUPERIO DEVICE
* Onboard FDC
Controller
Select Enabled if your system has a floppy drive controller (FDC) installing in the system board and you want to use it. If you install add-in FDC or the system has no floppy drive, select Disabled in this field. The choices: Enabled; Disabled.
Item Help
Menu Level
Onboard FDC Controller Onboard Serial Port 1 Onboard Serial Port 2 UART Mode Select UR2 Duplex Mode Onboard Parallel Port Parallel Port Mode ECP Mode Use DMA Game Port Address Midi Port Address Midi Port IRQ
CMOS Setup Utility - Copyright (C) 1984-2001 Award Software
VIA SuperIO Device
:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults
Enabled 3F8/IRQ4 2F8/IRQ3 Normal Half 378/IRQ7 SPP 3
Disabled Disabled
10
Page 75
Chapter 4 BIOS Setup
75
* Game Port Address This item allows you to select the onboard game
port I/O address.
* ECP Mode Use DMA Select a DMA channel for the port.
* Parallel Mode Select an operating mode for the on-board parallel
(printer) port. Select Normal, Compatible, or SPP unless you are certain your hardware and software both support one of the other available modes.
* Onboard Parallel Port This item allows you to determine onboard parallel
port controller I/O address setting. The choices: 378H/IRQ7; 278H/IRQ5; 3BC/IRQ7; Disabled.
* UR2 Duplex Mode This item allows you to select the IR half / full
duplex function. The choices: Half; Full.
* Midi Port Address This item allows you to select the onboard Midi port
I/O address.
* Midi Port IRQ This item allows you to select the Midi port IRQ.
Init Display First Initialize the AGP video display before initializing any
other display device on the system. Thus the AGP display becomes the primary display.
OnChip USB Control-
ler
Select Enabled if your system contains a Universal Serial Bus (USB) controller and you have USB peripherals.
Page 76
75DRV/75DRV-X
76
IDE HDD Block Mode Block mode is also called block transfer, multiple
commands, or multiple sector read/write. If your IDE hard drive supports block mode (most new drives do), select Enabled for automatic detection of the optimal number of block read/write per sector the drive can support. The choices: Enabled; Disabled.
USB Keyboard Sup-
port
Select Enabled if your system contains a Universal Serial Bus (USB) controller and you have a USB keyboard.
3. Press <ESC> to return to the Main Menu when you finish setting up all
items.
Page 77
Chapter 4 BIOS Setup
77
• POWER MANAGEMENT SETUP allows you to set the system’s power saving functions.
Run the POWER MANAGEMENT SETUP as follows:
1. Choose “POWER MANAGEMENT SETUP” from the Main Menu and a
list of options will appear:
2. Use one of the arrow keys to move between options and modify the
selected options by using PgUp / PgDn / + / - keys. An explanation of the <F> keys follows:
<F1>: “Help” gives options available for each item. <F5>: Get the previous values. These values are the values with which the
user starts the current session. <F6>: Load all options with the BIOS default values. <F7>: Load all options with the Setup default values.
4-6.6 POWER MANAGEMENT SETUP
ACPI Function ACPI Suspend Type Power Management Option HDD Power Down Suspend Mode Video Off Option Video Off Method MODEM Use IRQ Soft-Off by PWRBTN State After Power Failure IRQ/Event Activity Detect
Item Help
Menu Level
CMOS Setup Utility - Copyright (C) 1984-2001 Award Software
Power Management Setup
:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults
Enabled S1(POS) User Define Disabled Disabled Suspend->Off V/H SYNC+Blank 3 Instant-Off Auto Press Enter
Page 78
75DRV/75DRV-X
78
HDD Power Down When enabled and after the set time of system
inactivity, the hard disk drive will be powered down while all other devices remain active.
ACPI Suspend Type This item allows you to select the ACPI suspend
type. You can select S3(STR) for suspending to DRAM or S1(POS) for power on suspend under Windows 98 ACPI mode. The choice: S1(POS), S3(STR).
ACPI Function Select Enabled only if your computer’s operating
system supports the Advanced Configuration and Power Interface (ACPI) specification. Currently, Windows NT 5.0 support ACPI.
Suspend Mode After the selected period of system inactivity, the
chipset enters a hardware suspend mode, stopping the CPU clock and possibly causing other system devices to enter power management modes.
Video Off Option When enabled, this feature allows the VGA adapter
to operate in a power saving mode.
Power Management
Option
This option allows you to select the type (or degree) of power saving for Doze, Standby, and Suspend modes. This table describes each power management mode:
Max Saving
User Define
Min Saving
Maximum power savings. Only Available for SL CPUs. Inactivity period is 1 minute in each mode.
Set each mode individually. Select time-out period in the section for each mode stated below.
Minimum power savings. Inactivity period is 1 hour in each mode (except the hard drive).
Page 79
Chapter 4 BIOS Setup
79
State After Power
Failure
This field lets you determine the state that your PC returns to after a power failure. The choices: On; Off; Auto.
MODEM Use IRQ Name the interrupt request (IRQ) line assigned to
the modem (if any) on your system. Activity of the selected IRQ always awakens the system. The choices: 3; 4; 5; 7; 9; 10; 11; NA.
Soft-Off by PWRBTN When Enabled, turning the system off by pressing
the on/off button places the system in a very low­power-usage state.
Video Off Method This determines the manner by which the monitor is
blanked.
V/H SYNC + Blank
DPMS Supports
Blank Screen
This selection will cause the system to turn off the vertical and horizontal synchronization ports and write blanks to the video buffer.
This option only writes blanks to the video buffer.
Select this option if you monitor supports the Display Power Management Signaling (DPMS) standard of the Video Electronics Standards to select video power management values.
All Modes -->Off
Suspend -->Off
Monitor will remain on during power saving modes.
Monitor blanked when the systems enters the Suspend mode.
Monitor blanked when the system enters either Suspend or Standby modes.
Always On
Page 80
75DRV/75DRV-X
80
IRQ/EVENT ACTIVITY DETECT
* VGA When Enabled, you can set the VGA awakens the
system.
* LPT & COM When LPT & COM is ON, any activity from one of
the listed system peripheral devices or IRQs wakes up the system.
* HDD & FDD When HDD & FDD is ON, any activity from one of
the listed system peripheral devices wakes up the system.
* PCI Master When PCI Master is ON, any activity from one of
the listed system peripheral devices wakes up the system.
Item Help
Menu Level
:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults
Disabled OFF LPT/COM ON OFF Disabled Disabled Disabled 0 0 0 0 Press Enter
USB Resume from S3 VGA LPT & COM HDD & FDD PCI Master PowerOn by PCI Card Wake Up On LAN/Ring RTC Alarm Resume Date (of Month) Resume (hh:mm:ss) IRQs Activity Monitoring
CMOS Setup Utility - Copyright (C) 1984-2001 Award Software
IRQ/Event Activity Detect
* USB Resume from S3 This item will enable you to wake-up the system by
use keyboard when you shut down the computer in S3 mode. The choices: Enabled, Disabled.
Page 81
Chapter 4 BIOS Setup
81
* RTC Alarm Resume When Enabled, you can set the data and time at
which the RTC (Real Time Clock) alarm awakens the system from suspend mode. The choices: Disabled (default); Enabled.
* Date (of Month) Set a certain date when RTC Alarm Resume
option is Enabled to awaken the system. This option is concurrent with Resume Time option.
* Resume Time (hh:
mm:ss)
Set a certain time when RTC Alarm Resume option is Enabled to awaken the system. This option is concurrent with Date option.
* Wake Up On LAN/
Ring
An input signal on the serial Ring Indicator (RI) line (in other words, an incoming call on the modem) awakens the system from a soft off state. The choices: Enabled; Disabled.
* PowerOn by PCI Card This item allows system wake up by PCI Device.
Page 82
75DRV/75DRV-X
82
3. Press <ESC> to return to the Main Menu when you finish setting up all
items.
IRQ Activity Monitor-
ing
The following is a list of IRQ’s (Interrupt Requests), which can be exempted much as the COM ports and LPT ports above can. When an I/O device wants to gain the attention of the operating system, it sig­nals this by causing an IRQ to occur. When the op­erating system is ready to respond to the request, it interrupts itself and performs the service. When set On, activity will neither prevent the system from go­ing into a power management mode nor awaken it.
* IRQ ACTIVITY MONITORING
Primary INTR IRQ-3 (COM2) IRQ-4 (COM1) IRQ-5 (LPT2) IRQ-6 (Floppy Disk) IRQ-7 (LPT1) IRQ-8 (RTC Alarm) IRQ-9 (IRQ2 Redir) IRQ-10 (Reserved) IRQ-11 (Reserved) IRQ-12 (PS/2 Mouse) IRQ 13 (Coprocessor) IRQ 14 (Hard Disk) IRQ 15 (Reserved)
Item Help
Menu Level
CMOS Setup Utility - Copyright (C) 1984-2001 Award Software
IRQ Activity Monitoring
:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults
ON Enabled Enabled Enabled Enabled Enabled Disabled Disabled Disabled Disabled Enabled Enabled Enabled Disabled
Page 83
Chapter 4 BIOS Setup
83
• PNP/PCI CONFIGURATION allows you to modify the system’s power saving functions.
Run the PNP/PCI CONFIGURATION as follows:
1. Choose “PNP/PCI CONFIGURATION” from the Main Menu and a screen
with a list of options will appear:
2. Use one of the arrow keys to move between options and modify the
selected options by using PgUp / PgDn / + / - keys. An explanation of the <F> keys follows:
<F1>: “Help” gives options available for each item. <F5>: Get the previous values. These values are the values with which the
user starts the current session. <F6>: Load all options with the BIOS default values. <F7>: Load all options with the Setup default values.
4-6.7 PNP / PCI CONFIGURATION
PNP OS Installed Reset Configuration Data
Resources Controlled By IRQ Resources
PCI/VGA Palette Snoop Assign IRQ For VGA Assign IRQ For USB PCI SLOT1/5 IRQ Assigned PCI SLOT2 IRQ Assigned PCI SLOT3 IRQ Assigned PCI SLOT4 IRQ Assigned
Item Help
Menu Level
CMOS Setup Utility - Copyright (C) 1984-2001 Award Software
PnP/PCI Configurations
:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults
No Disabled
Auto(ESCD) Press Enter
Disabled Enabled Enabled Auto Auto Auto Auto
Page 84
75DRV/75DRV-X
84
Reset Configuration
Data
Normally, you leave this Disabled. Select Enabled to reset Extended System Configuration Data (ESCD), when you exit Setup if you have installed a new add-on and the system reconfiguration has caused such a serious conflict that the operating system cannot boot.
Resource ControlledByThe Plug and Play AwardBIOS can automatically
configure all the boot and Plug and Play-compat­ible devices. If you select Auto, all the interrupt re­quest (IRQ) and DMA assignment fields disappear, as the BIOS automatically assigns them.
PCI/VGA Palette Snoop This option allows the BIOS to preview VGA status,
and to modify the information delivered form the fea­ture Connector of the VGA card to MPEG card. This option can solve the display inversion to black after you have used MPEG card.
Assign IRQ for USB Select Enabled if you system has a USB controller
and you have one or more USB devices connected. If you are not using your system’s USB controller, select Disabled to free the IRQ resource.
Assign IRQ for VGA Select Enabled if you system has a VGA controller
and you have one or more VGA devices connected. If you are not using your system’s VGA controller, select Disabled to free the IRQ resource.
NOTE: BIOS will automatically disable all PnP resources except the boot
device card when you select Yes on Non-PnP operating system.
PNP OS Installed Select Yes if the system operating environment is
Plug-and-Play aware (e.g., Windows95).
Page 85
Chapter 4 BIOS Setup
85
3. Press <ESC> to return to the Main Menu when you finish setting up all
items.
PCI SLOT1/5, 2, 3, 4
IRQ Assigned
These options allow you to assign an IRQ for each PCI SLOT and this is a useful function when you want to clear the IRQ conflict for a specific device. The options are available : Auto; 3; 4; 7; 9; 10; 11.
IRQ RESOURCES Press Enter. Please refer to the list below:
IRQ-3 assigned to PCI/ISA PnP IRQ-4 assigned to PCI/ISA PnP IRQ-5 assigned to PCI/ISA PnP IRQ-7 assigned to PCI/ISA PnP IRQ-9 assigned to PCI/ISA PnP IRQ-10 assigned to PCI/ISA PnP IRQ-11 assigned to PCI/ISA PnP IRQ-12 assigned to PCI/ISA PnP IRQ-14 assigned to PCI/ISA PnP IRQ-15 assigned to PCI/ISA PnP
Item Help
Menu Level
CMOS Setup Utility - Copyright (C) 1984-2001 Award Software
IRQ Resources
:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults
Page 86
75DRV/75DRV-X
86
• This section helps you to get more information about your system including CPU temperature, FAN speed and voltage. It is recommended that you contact with your mainboard supplier to get proper values about the setting of the CPU temperature.
Run the “SMARTDOC ANTI-BURN SHIELD” as follows:
1. Choose “SMARTDOC ANTI-BURN SHIELD” from the Main Menu and a
screen with a list of options will appear:
2. Use one of the arrow keys to move between options and modify the
selected options by using PgUp / PgDn / + / - keys.
<F1>: “Help” gives options available for each item. <F5>: Get the previous values. These values are the values with which the
user starts the current session. <F6>: Load all options with the BIOS default values. <F7>: Load all options with the Setup default values.
4-6.8 SMARTDOC ANTI-BURN SHIELD
Shutdown Temperature 60˚C/140˚F CPU Vcore DDR DIMM
3.3V +5V +12V
-12V
-5V 5VSB Voltage Battery Temperature 1 Temperature 2 Fan 1 Speed Fan 2 Speed
Item Help
Menu Level
CMOS Setup Utility - Copyright (C) 1984-2001 Award Software
SmartDOC Anti-Burn shield
:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults
0 1
3
2
4 5 6 7
Page 87
Chapter 4 BIOS Setup
87
Shutdown Tempera-
ture
This feature prevents your CPU from damage by over heat. If the CPU’s temperature is higher than “CPU warning temperature” that you select in this field, the BIOS will shut down your system within 3 seconds.
CPU Vcore Shows CPU core actual voltage value.
DDR DIMM Shows DDR DIMM actual voltage value.
3. Press <ESC> to return to the Main Menu when you finish setting up all items.
FAN 1/2 Speed These fields display the current speed of up to three
CPU fans, if your computer contains a monitoring system.
Temperature 1/2/3 This field displays the current CPU temperature, if
your computer contains a monitoring system.
Page 88
75DRV/75DRV-X
88
Run the “FREQUENCY/VOLTAGE CONTROL” as following:
1. Choose “FREQUENCY/VOLTAGE CONTROL” from the Main Menu and
a screen with a list of options will appear:
2. Use one of the arrow keys to move between options and modify the
selected options by using PgUp / PgDn / + / - keys.
<F1>: “Help” gives options available for each item. <F5>: Get the previous values. These values are the values with which the
user starts the current session. <F6>: Load all options with the BIOS default values. <F7>: Load all options with the Setup default values.
4-6.9 FREQUENCY/VOLTAGE CONTROL
Red Storm Overclocking CPU Vcore Select Auto Detect DIMM/PCI CIK Spread Spectrum CPU Skew Adjust CHIP Skew Adjust PCI Skew Adjust AGP Skew Adjust Use CPU Linear Freq CPU Clock
Item Help
Menu Level
CMOS Setup Utility - Copyright (C) 1984-2001 Award Software
Frequency/Voltage Control
:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults
Press Enter Default Enabled Disabled Disabled Disabled Disabled Disabled Use Linear 100
Page 89
Chapter 4 BIOS Setup
89
CPU Skew
Adjust
Leave this field at default.
Auto Detect
DIMM/PCI CLK
This item allows you to enable/disable detect DIMM/ PCI Clock. The choice: Enabled, Disabled.
Spread Spec-
trum
This item allows you to enable/disable the spread spectrum modulate. The choice: Enabled, Disabled.
Redstorm
Overclocking
Tech
Please press <Enter> to start RED STORM OVER­CLOCKING TECH, this option helps user an easy
way to overclocking, it will increase CPU external clock automatically, when CPU external clock in­creasing to unacceptable value, BIOS will restart your system, then running at acceptable CPU ex­ternal clock.
CPU Vcore
Select
This item allows users to adjust the CPU Vcore voltage. The instant damage of CPU is due to the wrong Vcore voltage setting, so we highly recom­mend that user should leave this item to Default setting unless you fully understand it.
CHIP Skew
Adjust
Leave this field at default.
AGP Skew
Adjust
Leave this field at default.
PCI Skew Adjust Leave this field at default.
Page 90
75DRV/75DRV-X
90
Use CPU Linear
Freq
If users would like to adjust CPU clock, this items must be “Linear”. The choices: Default; Linear.
CPU Clock These items allows users to adjust CPU frequency.
3. Press <ESC> to return to the Main Menu when you finish setting up all items.
Page 91
Chapter 4 BIOS Setup
91
4-6.11 SET SUPERVISOR / USER PASSWORD
• These two options allow you to set your system passwords. Normally, the supervisor has a higher priority to change the CMOS setup option than the users. The way to set up the passwords for both Supervisor and Users are as follows:
1. Choose “Change Password” in the Main Menu and press <Enter>. Then
following message appears:
“Enter Password : “
2. The first time you run this option, enter your password up to 8 characters
and press <Enter>. (The screen does not display the entered characters.)
3. After you enter the password, the following message appears prompting
you to confirm the password:
“Confirm Password : “
4. Enter the same password “exactly” the same as you have just typed to
confirm the password and press <Enter>.
5. Move the cursor to Save & Exit Setup to save the password.
6. If you need to delete the password entered before, choose the Supervi-
sor Password and press <Enter>. It will delete the password that you have entered before.
• When you press <Enter> on this item, you will get a confirmation dialog box with a message similar to:
“ Load Optimized Defaults (Y / N) ? N ”
Pressing “Y” loads the BIOS default values that are factor settings for opti­mal performance of system operations.
4-6.10 LOAD OPTIMIZED DEFAULTS
Page 92
75DRV/75DRV-X
92
NOTE: If you forget or lose the password, the only way to access the
system is to clear the CMOS RAM. All setup informations will be lost and you need to run the BIOS setup program again.
7. Move the cursor to Save & Exit Setup to save the option you have just configured; otherwise the old password will still be there the next time
you turn your system on.
8. Press <Enter> to exit to the Main Menu.
4-6.12 SAVE & EXIT SETUP
• SAVE & EXIT SETUP allows you to save all modifications you have speci­fied into the CMOS memory. Highlight this option on the Main Menu and the following message appears:
“SAVE to CMOS and EXIT (Y/N) ? Y “
“Y” is for “Yes”, and “N” is for “No”. Press <Enter> key to save the configuration changes.
4-6.13 EXIT WITHOUT SAVING
• EXIT WITHOUT SAVING option allows you to exit the Setup Utility with­out saving the modifications that you have specified. Highlight this option on the Main Menu and the following message appears:
“Quit Without Saving (Y/N) ? N “
“Y” is for “Yes”, and “N” is for “No”. You may change the prompt to “Y” and press <Enter> key to leave this option .
Page 93
Chapter 4 BIOS Setup
93
MEMO
MEM
O
Page 94
75DRV75DRV-X
94
APPENDICES
APPENDIX-1 TECHNICAL TERMS APPENDIX-2 IDENTIFYING BIOS VERSION/ BIOS PART NUMBER APPENDIX-3 IDENTIFYING MAINBOARD MODEL NUMBER
Page 95
APPENDIX
95
Technical Terms Introduction
Tech Term
AGP
AMR
ACR
CPU Central Processing Unit
CMOS Complementary Metal Oxide Semiconductor
CRIMM Continuity RIMM
CNR Communication and Networking Riser
Advanced Communication Riser
Audio Modem Riser
Accelerated Graphic Port
Meaning
DMA Direct Memory Access
DMI Desktop Management Interface
DIMM Dual Inline Memory Module
DRAM Dynamic Random Access Memory
DDR Double Data Rate
ECP Extended Capabilities Port
ESCD Extended System Configuration Data
ECC Error Check and Correct
EPP Exhanced Parallel Port
FDD Floppy Disk Device
IDE Integrated Dual Channel Enhanced
IRQ Interrupt ReQuest
I/O Input/Output
LAN Local Area Network
LBA Logical Block Addressing
LED Local Emitting Diode
MHz Megahertz
PNP
Plug & Play
USB
Universal Serial Bus
VCM
Virtual Channel Memory
APPENDIX-1 TECHNICAL TERMS
Page 96
75DRV75DRV-X
96
APPENDIX-2 IDENTIFYING BIOS VERSION AND BIOS PART NUMBER
• When you boot up your computer, you may see a screen which shows your computer is phoenixnet™ enabled. Please see Picture-1 below for an illustration.
• When the screen shows up press “Tab” key for BIOS information.
Picture-1
Page 97
APPENDIX
97
• See Picture-2 below for BIOS version and BIOS part number identification.
Picture-2
1
2
1. BIOS VERSION
example: REV T2.1
2. BIOS ID STRING
example: 6A69RSNCC
Page 98
75DRV75DRV-X
98
APPENDIX-3 IDENTIFYING MAINBOARD MODEL NUMBER
• Usually the mainboard model number is labeled on the side of ISA side of slot or PCI slot. Please see the picture below as an illustration:
2
1
1. MAINBOARD MODEL NUMBER
example: SL-65KV2
2. MAINBOARD SERIAL NUMBER
example: 0012000T005679
Page 99
APPENDIX
99
Loading...
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use