Soleus Air PH4-10R-01 User Manual

Portable Air Conditioner with

Heat Pump Technology

PH4-10R-01, PH4-12R-01, & PH4-14R-01

Operating Instructions

3092402

Thank you for choosing a Soleus Air Portable Air Conditioner with Heat Pump Technology. This owner’s manual will provide you with valuable information necessary for the proper care and maintenance of your new product. Please take a few moments to thoroughly read the instructions and familiarize yourself with all the operational aspects of your new Soleus Air Portable Air Conditioner with Heat Pump technology.

For your own records, please attach a copy of your sales receipt to this manual. Also, write the store name/location, date purchased, and serial number below:

Store Name: ____________________________________________________

Location: ______________________________________________________

Date Purchased: _________________________________________________

Serial Number (located on back of unit): ______________________________

IMPORTANT INSTRUCTIONS

Before installing and using your portable air conditioner, please read this owner’s manual carefully. Store this manual in a safe place for future reference.

1) Always place the unit on a level surface.

2) Never use or store gasoline or other flammable vapor or liquid near this unit unless instructed by this

manual.

3) Maintain at least 10 inches (25 cm) clearance space around this unit. Do not block or cover air inlet or

outlet grilles.

4) The unit must be connected to a correctly grounded power supply.

5) Do not start or stop the unit by inserting or pulling out the power plug.

6) Do not use an adapter plug or extension cord.

7) Do not use the unit in the immediate surroundings of a bath, a shower or a swimming pool.

8) Do not insert anything into the air outlet. Do not obstruct air inlet or outlet grills unless instructed by this

manual.

9) Do not let children play near this unit.

10) Always inspect the cord for signs of damage before use. If the power cord is damaged, it must be replaced

by the manufacturer or a qualified service technician.

11) When cleaning the unit, always turn the unit off and unplug the power cord.

PACKAGE CONTENTS

Portable Air Conditioner Exhaust Hoses (2) Hose Adapters (2) Window Kit Adapter (2) Remote Control AAA Batteries (2) Window Kit - 4 Sliding Panels (1 dual hose panel, 1 single hose panel, 2 extension panels) Air Intake and Outlet Covers (2) Air Intake Vent for Single Hose Installation (Additional Accessory) (1) Owner’s Manual

SPECIFICATIONS

• The cooling capacity is measured at an ambient temperature of DB 86 °F, WB 78 °F.

• Noise level is measured at a distance of 3.28 ft away from the front of the unit, when the unit is in cooling mode.

• Power consumption is measured when the fan runs at the highest speed setting.

• These specifications are for reference only. For actual data, please refer to the rating label on the back of the unit.

• If the environment temperature is higher than the max operating temperature or lower than the minimum operating temperature,

the air conditioner may not work properly.

MODEL PH4-10R-01

COOLING CAPACITY 10,000 BTU/H

HEATING CAPACITY 10,000 BTU/H

DEHUMIDIFIER CAPACITY 50 pts/Day

POWER

AIR FLOW VOLUME 225 CFM

POWER SOURCE

SOUND PRESSURE LEVEL 42 dB(A)

NET WEIGHT 76 Lbs

OPERATING

TEMP

DIMENSIONS

REFRIGERANT R22

COOLING 1200W

HEATING 950W

115 V~ 60 HZ

8.6 AND 10.5 AMP

HEATING/COOLING

COOLING

HEATING

UNIT

PACKAGE

60.8℉-107.6℉

23℉-89.6℉

19” W ×32.25” H ×

18.5” D

22.6” W ×34.3” H ×

21.4” D

PH4-12R-01

12,000 BTU/H

60 pts/Day

1350W 1160W

225 CFM

115 V~ 60 HZ

10.8 AND 12 AMP

HEATING/COOLING

46 dB(A)

82 Lbs

60.8℉-107.6℉

23℉-89.6℉

19” W ×32.25” H ×

18.5” D

22.6” W ×34.3” H ×

21.4” D

R22

PH4-14R-01

14,000 BTU/H

14,200 BTU/H

65 pts/Day

1390W 1180W

225 CFM

115 V~ 60 HZ

11 AND 12.5 AMP

HEATING/COOLING

46 dB(A)

82 Lbs

60.8℉-107.6℉

23℉-89.6℉

19” W ×32.25” H ×

18.5” D

22.6” W

×34.3” H ×

21.4” D

R22

LCDI POWER CORD AND PLUG

This air conditioner is equipped with an LCDI (Leakage Current Detection and Interruption) power cord and plug as required by US National Electric Code 440.65. This cord consists of a length of shielded flexible cord with no termination on the load side and a LCDI attachment plug on the line side.

The LCDI power cord and plug will remove the supply source via electrical disconnect (circuit trip) if the nominal current leakage between the cord shield and either load conductor exceeds a predetermined value. The cord will remain de-energized until the devise has been manually reset. This is intended to reduce the risk of a fire in the power cord or combustible materials nearby. The cord shields are not grounded and they must be considered a shock hazards if exposed. The cord shield must not be connected to ground or to any exposed metal.

The test and reset buttons on the LCDI Plug are used to check if the plug is functioning properly. To test:

1. Plug power cord into wall outlet

2. Press TEST Button, circuit should trip, cutting power to the air conditioner

3. Press RESET button for use

If a test is performed and the indicator light remains ON, current leakage has been detected. Do not use the air conditioner or attempt to reset the LCDI Plug. Contact Soleus Air Customer Service for troubleshooting recommendations.

WARNING:

1. DO NOT press the TEST button while the air conditioner is operating.

2. The TEST and RESET buttons should not be used as “ON” and “OFF” switches.

3. The cord and plug are not intended to offer protection to externally connected loads or supply circuits.

4. The cord and plug are intended for indoor use only.

RESET TEST

PARTS & ASSEMBLY

PARTS

EXHAUST HOSES

WINDOW KIT

ASSEMBLY & INSTALLATION

INSTALLATION

When the unit is operating as an air conditioner, heater, or dehumidifier, the unit draws in fresh outdoor air and exhausts hot air (in AC or dehumidifier mode) or cool air (in Heat mode) out of the room to complete the air exchange. When the unit is operating in fan mode, no outdoor air exchange takes place. The window kit and exhaust hose do not need to be installed when the unit is used as a fan.

NOTE: The supplied window kit can be installed in sliding windows and sliding glass doors up to 8 ft. long (approximate length).

MOUNTING THE EXHAUST HOSES

• Choose a suitable location, near a grounded electrical outlet and suitable window or door. Remove

• Extend both ends of the exhaust hoses approximately 6 inches.

• Screw the window kit adapter onto one end of the exhaust hose clockwise. Screw the hose adapter onto

• Remove outlet covers from the back of the unit by screwing them counter-clockwise, then lifting up.

• Mount the exhaust hoses onto the back of the unit by locking the hose adapters into place.

packaging and locate components.

the other end of the exhaust hose clockwise. Repeat on the other exhaust hose.

+ 11 hidden pages