Soleus Air PA1-12R-32, PA1-14R-32 User Manual

Portable Air Conditioner, Heat Pump Heater,

Dehumidifier, Fan, & HEPA Air Purifier

PA1-12R-32 / PA1-14R-32

Operating Instructions

3046364

Model No. PA1-12R-32 / PA1-14R-32

Thank you for choosing a Soleus Air Portable Air Conditioner. This owner’s manual will provide you with valuable information necessary for the proper care and maintenance of your new product. Please take a few moments to thoroughly read the instructions and familiarize yourself with all the operational aspects of your new Soleus Air Portable Air Conditioner.

For your own records, please attach a copy of your sales receipt to this manual. Also, write the store name/location, date purchased, and serial number below:

Store Name: ____________________________________________________

Location: ______________________________________________________

Date Purchased: _________________________________________________

Serial Number (located on back of unit): ______________________________

IMPORTANT INSTRUCTIONS

Before installing and using your portable air conditioner, please read this owner’s manual carefully. Store this manual in a safe place for future reference.

1) Always place the unit on a level surface.

2) Never use or store gasoline or other flammable vapor or liquid near this unit unless instructed by this

manual.

3) Maintain at least 10 inches (25 cm) clearance space around this unit. Do not block or cover air inlet or

outlet grilles.

4) The unit must be connected to a correctly grounded power supply.

5) Do not start or stop the unit by inserting or pulling out the power plug.

6) Do not use an adapter plug or extension cord.

7) Do not use the unit in the immediate surroundings of a bath, a shower or a swimming pool.

8) Do not insert anything into the air outlet. Do not obstruct air inlet or outlet grills unless instructed by this

manual.

9) Do not let children play near this unit.

10) Always inspect the cord for signs of damage before use. If the power cord is damaged, it must be replaced

by the manufacturer or a qualified service technician.

11) When cleaning the unit, always turn the unit off and unplug the power cord.

PACKAGE CONTENTS

Portable Air Conditioner Exhaust Hoses (1) Hose Adapters (1) Window Kit Adapter (1) HEPA Filter (1) Remote Control AAA Batteries (2) Window Kit - 3 Sliding Panels (1 single hose panel, 2 extension panels) Owner’s Manual

SPECIFICATIONS

• The cooling capacity is measured at an ambient temperature of DB 86 °F, WB 78 °F.

• Noise level is measured at a distance of 3.28 ft away from the front of the unit, when the unit is in cooling mode.

• Power consumption is measured when the fan runs at the highest speed setting.

• These specifications are for reference only. For actual data, please refer to the rating label on the back of the unit.

• If the environment temperature is higher than the max operating temperature or lower than the minimum operating temperature,

the air conditioner may not work properly.

MODEL PA1-12R-32

Cooling Capacity 12,000 BTU/Hr Heating Capacity 12,500 BTU/Hr

Dehumidifying Capacity 63 pts/day

Air Purifier Capacity Removes 99.97% Microns

Cooling 1387 Watts

Power Consumption

Air Flow Volume 265 CFM

Power Source 115 V / 60 HZ

Rated Current

Sound Pressure Level <50db(A)

Weight 86.9 lbs

Dimensions (WxDxH) 17.87”x14.3”x32.1”

Refrigerant R22

Heating 1180 Watts

Cooling 12.7 A Heating 10.8 A

PA1-14R-32

14,000 BTU/Hr 14,500 BTU/Hr

63 pts/day

Removes 99.97% Microns

1485 watts

1200 Watts

265 CFM

115 V / 60 HZ

13.6 A 11 A

<50db(A)

86.9 lbs

17.87”x14.3”x32.1”

R22

DISCLAIMER

ALL INFORMATION AND THE TECHNICAL SPECIFICATIONS PRESENTED IN THIS USER’S MANUAL ARE THE PRESENTATION OF THE MANUFACTURER. SOLEUS INTERNATIONAL HAS NOT CONDUCTED INDEPENDENT TEST TO THE INFORMATION AND THE SPECIFICATIONS PRESENTED HEREWITHIN.

PRODUCT DIAGRAM (Actual product design may differ slightly from images below)

FRONT

A. Control panel

B. Air outlet C. Casters D. Power Cord & Plug E. Drain Plug F. HEPA Air Purifier Storage

BACK

A. Hot air outlet grill B. Lower air inlet grill C. HEPA Air Purifier Holder D. HEPA Air Purifier

ACCESSORIES

Flexible exhaust hose with 2 adapters

• 3-piece set

• stretches from 14 1/4” to 60 5/8” (36cm to 150cm)

Adjustable window slider kit

• 3-piece set

• adjusts 33 1/2” to 81” Drain tube Drain pan

INSTALLATION

SELECTING THE LOCATION

Place the unit in a flat location where the air outlets are not obstructed. Place the unit at least 20” (50cm) away from a wall or other obstacle.

MOUNTING THE EXHAUST HOSE

Slide the square end of the exhaust duct over the hot air outlet on the back of the unit.

The exhaust hose should be kept as short and straight as possible. Prevent any sharp bends in the exhaust hose, as this will trap hot exhaust air.

The hot exhaust air can be vented through the wall or out a window. If mounting in the wall, the height of the hole should be 16 to 50 inches (40cm to 130cm).

Soleus Air does not provide a venting kit for through the wall ventilation. Venting through the wall requires a custom installation.

NOTE: The Portable Air Conditioner above may differ from the unit described in this manual. The above directions and images show general

directions for all Soleus Air single hose portable air conditioners.

LCDI POWER CORD AND PLUG

This air conditioner is equipped with an LCDI (Leakage Current Detection and Interruption) power cord and plug as required by US National Electric Code 440.65. This cord consists of a length of shielded flexible cord with no termination on the load side and a LCDI attachment plug on the line side.

The LCDI power cord and plug will remove the supply source via electrical disconnect (circuit trip) if the nominal current leakage between the cord shield and either load conductor exceeds a predetermined value. The cord will remain de-energized until the devise has been manually reset. This is intended to reduce the risk of a fire in the power cord or combustible materials nearby. The cord shields are not grounded and they must be considered a shock hazards if exposed. The cord shield must not be connected to ground or to any exposed metal.

The test and reset buttons on the LCDI Plug are used to check if the plug is functioning properly. To test:

1. Plug power cord into wall outlet

2. Press TEST Button, circuit should trip, cutting power to the air conditioner

3. Press RESET button for use

If a test is performed and the indicator light remains ON, current leakage has been detected. Do not use the air conditioner or attempt to reset the LCDI Plug. Contact Soleus Air Customer Service for troubleshooting recommendations.

WARNING:

1. DO NOT press the TEST button while the air conditioner is operating.

2. The TEST and RESET buttons should not be used as “ON” and “OFF” switches.

3. The cord and plug are not intended to offer protection to externally connected loads or supply circuits.

4. The cord and plug are intended for indoor use only.

RESET TEST

+ 12 hidden pages