Soler & Palau SWF-100, SWF-100x, SWF-150, SWF-150x, SWF-200 Installation Instructions Manual
Model SWF
Installation Instructions
U.S. Distribution Center
Soler & Palau USA
5985 Richard Street
Jacksonville, FL 32216
Phone:
Fax:
Important Notice: Read and Save these instructions for future reference.
800.961.7370
800.961.7379
www.solerpalau-usa.com
Installation Instructions for Model SWF
Dimensional Data
Model A B C C1 C2 D
SWF-100 13 ¼ 13 ¼ 9 3 2
SWF-100x 13 ¼ 13 ¼ 9 3 2
SWF-150 15 ½ 13 ¼ 10
SWF-150x 15 ½ 16
SWF-200 15 ½ 16
WARNING
Soler and Palau designs the highest quality products available in the industry and meets stringent manufacturing
requirements. These units are not designed however to be utilized as the primary devices used in a life support
ventilation systems where failure could result in loss or injury, the user should provide adequate backup ventilation, supplementary natural ventilation, failure alarm system, or acknowledge willingness to accept the risk of
such loss or injury
1
/
16 10 3
1
/
16 11
3
/
16 3 2
3
/
16 2
7
/
16 3
3
/
8 2
7
/
16 4
7
/
16 4
7
/
16 6
7
/
16 6
7
/
16 8
Installation Instructions for Model SWF
Fan Installation
WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY,
OBSERVE THE FOLLOWING:
(a) Use this unit only in the manner intended by the manufacturer. If you have any
questions contact the manufacturer.
(b) Before servicing or cleaning the unit, switch the power off at the service panel
and lock the service disconnecting means to prevent power from being
switched on accidentally. When the service disconnecting means cannot
be locked; securely fasten a prominent warning device such as a tag to the
service panel.
(c) Installation work and electrical wiring must be done by qualified
person(s) in accordance with all applicable codes & standards including related
construction.
(d) When cutting or drilling into wall or roof, do not damage electrical wiring and
other hidden utilities.
(e) CAUTION: For General Ventilating Use Only. Do Not Use To Exhaust
Hazardous Or Explosive Materials And Vapors.
(f) DO NOT USE with heated air in excess 140˚F (60˚C).
Select Fan Location
When selecting a location to install the SWF fan that has been chosen, take into
consideration the application of the product, the locations of fresh air intakes, and
sound generated by the SWF unit.
The fan should be located a minimum of 6 feet horizontally and 8 feet vertically
from any fresh air intakes for HVAC systems, heat recovery systems, etc. to prevent exhaust air streams from being re-introduced into the occupied space. Doors
or windows that are frequently opened during pleasant seasons may also be considered fresh air intakes so keep this in mind when selecting the location of the SWF.
Installation Instructions for Model SWF
Fan Installation Con’t
Mark and Introduce Required Holes
Once the location on the exterior wall where the fan is to be mounted has been
selected, mark all screw and hole locations utilizing the included template. Cut the
holes through the wall for the duct connection and for the electrical conduit. Measure the thickness of the wall and the length of the duct connection that is supplied
on the SWF fan. Cut a length of duct so that once connected to the fan, will extend
2” through the wall.
If mounting the fan on a masonry wall, drill four holes and insert wall anchors. If
mounting to wooden structure, you will utilize wood screws to secure the SWF to
the wall.
If the fan is to be mounted on a wall surface which is not flush such as lapped siding,
a mounting plate to provide for a flush fit needs to be made.
Mount the Fan
Insert electrical supply through the wall. Attach the duct extension to the SWF
making sure that the connection is secure. Apply a generous amount of exterior
silicone caulk to backplate of the fan to ensure an airtight/waterproof connection
between the fan and the wall surface. If a mounting frame is used in conjunction
with lapped siding, be certain to apply a generous amount of caulk between the
frame and the wall as well as the fan backplate and the frame. Mount the fan to the
wall.
Note: Be certain to make an airtight seal around all interior wall penetrations before attaching duct work.
Electrical Connection
All SWF series fans operate from a standard 120V 60Hz A.C electrical supply. All
wiring must be carried out in accordance with National Electrical Code, and all applicable state and local buildings codes.
Installation Instructions for Model SWF
WIRING INSTRUCTIONS
WARNING! Make sure that power supply is disconnected and locked to
prevent accidental activation.
1. Remove the screws securing the terminal box cover plate located on the fan
motor mounting bracket. All fan motor and capacitor connections are pre-wired
to the electrical terminal strip. A 3/8” romex type cable restraint connector will
be needed to secure the wiring through the knockout provided on the side of the
terminal box.
2. Bring incoming electrical service through the romex connector and the fan
electrical service opening. Using a small regular screwdriver, tighten the neutral
(white) wire of the incoming 115V power supply under the open terminal strip port
opposing the motor Blue wire. Tighten the line (black) wire of the incoming supply
under the open terminal opposing the motor Black wire. Now, secure the source
ground to the open terminal strip opposing the Green/Yellow Wire.
3. Secure the romex connector. Secure the incoming supply with the romex connector. Replace the fan terminal box cover.
4. Apply a generous bead of silicone caulk around the electrical provision hole in
the backplate of the fan to provide for a secure seal.
MAINTENANCE INSTRUCTIONS
1. Since fan bearings are sealed and provided with an internal lubricating material,
no additional lubrication is necessary.
2. It is recommended that the cover is screen is checked on a regular basis to
check for any obstructions and the cover is removed and the motor and wheel are
inspected and cleaned as necessary.
No other maintenance is necessary.
Installation Instructions for Model SWF
WIRING DIAGRAMS
Installation Instructions for Model SWF
WIRING DIAGRAMS
Motor without speed controller
Motor with speed controller
Installation Instructions for Model SWF
FIVE (5) YEAR WARRANTY
Soler & Palau warrants that the POWERVENT series exhaust fan will be free from
defective materials and workmanship for the period of (5) years from the date of
original purchase. In the event that we and any part defective the product will be
repaired or, in the Company’s discretion, replaced without charge provided that the
product has been installed in accordance with the enclosed instructions and all applicable EPA Standards and state and local building codes.
IF CLAIMING UNDER WARRANTY
Please return the complete product, freight paid, to your local authorized distributor.
All returns must be accompanied by a valid Bill Of Sale. All returns must be clearly
marked “Warranty Claim,” with an accompanying description stating the nature of
the fault.
THE FOLLOWING WARRANTIES DO NO APPLY
Damages from shipping, either concealed or visible. Claim must be filed with the
carrier. Damages resulting from improper wiring or installation
Damages caused by acts of nature, or resulting from improper consumer procedures
such as: Improper Maintenance; Misuse; Negligence; Alteration; Abuse; Abnormal
Use; or Accident or Incorrect Electrical Voltage and Current.
Removal or alteration to the Soler & Palau data plate label.
WARRANTY VALIDATION
The end user must keep a copy of the Bill of Sale to verify purchase date.
THE ABOVE FIVE (5) YEAR WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER
WARRANTIES, EXPRESSED, WRITTEN OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR USE. IN NO EVENT
SHALL SOLER & PALAU BE LIABLE FOR ANY SPECIAL, CONSEQUENTIAL, OR
INCIDENTAL DAMAGES, INCLUDING LOSS OF PROPERTY, REVENUES, LOST
PROFITS, and COSTS OF REMOVAL, INSTALLATION OR REINSTALLATION.
Loading...