SolaHD GLS60 Series, GLS60-M Series Instruction Sheet

GLS60 Series, GLS60-M Series Installation & Operating Instructions

M1

M2

To comply with the published safety standards, the following must be observed when using
this power supply:

1. Maximum ambient temperature for the power supply must not exceed 50°C.

2. When installing the power supply in the end-use equipment, special attention is
required to ensure safety compliance with the following safety standards: UL60950-1,
EN60950-1, IEC60950-1, and CSA22.2 No. 60950-1-03 for GLS62, GLS63, GLS64,
and GLS65; UL60601-1, EN60601-1, IEC60601-1, and CSA22.2 No. 60601-1-M90
for GLS63-M, GLS64-M, and GLS65-M. The safety requirements include creepage
distances, clearances, and distance through insulation between primary wiring and
earth or secondary (SELV) wiring.

3. The power supply’s rated input voltage is automatically selected for GLS62, GLS63,

GLS64, and GLS65. Please refer to the specication sheet for the input voltage range.
GLS63-M, GLS64-M, and GLS65-M are approved and certied for the rated voltage

range of 100 V ac to 250 V ac and/or 140 V dc to 300 V dc.

4. The maximum output power of the supply must not exceed the rating indicated in the

specication sheet.

5. The earth ground wire must be connected only to the point marked with the earth
ground symbol (on the unit).

6. The disconnection from the line must be in the end system.

7. Hazardous voltages exist in the primary circuits. Disconnect the power supply before
servicing.

8. When operating with a dc input voltage range, the unit input must be protected by a dc
rated fuse in the end-use installation system.

9. The internal fuse should only be replaced with a 3.15 A, 250 V ac, type SP0001.1009
manufactured by Schurter AG, type 2163.15 manufactured by Littelfuse, or type S501
manufactured by Cooper.

10. This power supply is not suitable for direct contact to the patient.

11. This equipment is considered Class I according to protection against electrick shock.

12. This power supply is

marked following the provisions of the Low Voltage Directive,

2006/95/EC.

13. For technical assistance, contact SolaHD Technical Support at (800) 377- 4384 or
send an e-mail to [e-mail]. Please visit our Web site at www.solahd.com for

additional product information and specication sheets.

Mechanical Outline

SK1

GND

R16

C32

C33

W6

R31

IC4

R32

C21

IC1

D1

1

T1

FB1

W4

3

D15

C27

J8

D16A

W2

SK201

V Adj. Pot

W3

1

SK2

6

Connector PIN Designation

Input Connector PIN GLS62 GLS63 (-M) GLS64 (-M) GLS65 (-M)

SK1

Output Connector PIN GLS62 GLS63 (-M) GLS64 (-M) GLS65 (-M)

SK2

SK201

NOte: Mounting holes M1 and M2 should be grounded for EMI purposes. Mounting hole M1 is a safety ground connection.

1 Neutral
3 Line

1

+5 V +12 V +15 V +24 V2
3
4

Common5
6
1 +Sense
2 -Sense

Output Ratings

Model

GLS62 +5 12.0
GLS63 (-M) +12 5.0 6.7
GLS64 (-M) +15 4.0 5.3
GLS65 (-M) +24 2.5 3.3

Output

Voltage (V)

Convection Cooling 30 CFM Forced Air Cooling

Max. Output

Current (A)

Max. Output

Power (W)

60

Max. Output

Current (A)

16.0

Max. Output

Power (W)

80

Visit our Web site at www.solahd.com or contact Technical Support at (800) 377- 4384 with any questions P/N: A272-198 Rev 0 5/12/09 Ref: 03361001333/03366200541

GLS60 Series, GLS60-M Series Installation & Operating Instructions

.22 [5.6]

2.55 [64.8]

3.00 [76.2]

.22 [5.6]

Mechanical Dimensions

Bottom View

4.55 [115.6]

5.00 [127.0]

Side View

6.69 [170.0]

1.57 [40.0]

Typical Ventilation Setup

Top View

AIR FLOW

FAN

7.28 [185.0] 4.33 [110.0]

Side View

T1

UNIT

1.08 [27.5] MAX

.06 [1.6]

All dimensions are in inches [mm]

Mounting hole diameter (4X): 0.15″ [3.81 mm]

.12 [3.0] MAX

Visit our Web site at www.solahd.com or contact Technical Support at (800) 377- 4384 with any questions.
GLS62, GLS63, GLS64, and GLS65 are commercial designations of model numbers LPS62, LPS63, LPS64, and LPS65 respectively.
GLS63-M, GLS64-M, and GLS65-M are commercial designations of model numbers LPS63-M, LPS64-M, and LPS65-M respectively.

4.33 [110.0]

FAN

AIR FLOW

UNIT

Fan: MINEBEA 3110NL-04W-B30
Fan Input: 12 V dc
NOTE: Dimensions and fan used are for reference only

While every precaution has been taken to ensure accuracy and completeness in this manual, EGS Electrical Group, LLC.

assumes no responsibility, and disclaims all liability for damages resulting from use of this information or for any errors or omissions.

©2009 EGS Electrical Group, LLC. All rights reserved. Specications subject to change without notice.

GLS60 Series Specifications

Electrical Specifications

Input

Input ra nge 85-264 Vac (wide range); 120-300 Vdc

Frequency 47-440 Hz

Inrush current <18 A peak @ 115 Vac, <36 A peak @ 230 Vac, cold start @ 25°C

Input current 1.5 A max. (RMS) @ 115 Vac

Efficiency 70% typical at full load

EMI filter

Safety ground
leakage current

Output

Maximum power 60 W convection; 80 W with 30 CFM forced air

Adjustment range -5, 10% min.

Hold-up time 20 ms @ 60 W load, 115 Vac nominal line

Overload protection

Overvoltage protection 5 V output; 5.7 to 6.7 Vdc; Other outputs 10% to 25% above nominal output

FCC Class B conducted; CISPR 22 Class B conducted;

EN55022 Class B conducted; VDE 0878 PT3 Class B conducted

<0.5 mA @ 50/60 Hz, 264 Vac input

Short circuit protection on all outputs.

Case overload protected @ 110-145% above peak rating

Remote sense Compensates for 0.5 V lead drop minimum, will operate without remote sense connected. Reverse connection protected

Environmental Specifications

Operating temperature

Storage temperature -40°C to 85°C
Temperature coefficient ±0.04% per °C

Electromagnetic
susceptibility

Humidity Operating; non-condensing 5% to 95% RH

Vibration Three orthogonal axes, sweep at 1 oct/min, 5 min. dwell at four major resonances 0.75G peak 5 Hz to 500 Hz, operational

MTBF demonstrated >550,000 hours at full load and 25°C ambient conditions

Mating Connectors

AC Input Molex 09-50-8031 (USA) Not required for (-T) option

09-91-0300 (UK); PINS: 08-58-0111

DC Outputs Molex 09-50-8061 (USA) Not required for (-T) option

09-91-0600 (UK); PINS: 08-58-0113

Remote Sense

Molex 22-01-2025
PINS: 08-52-0113

Connector Kit #70-841-006, includes all of the above

1. Specifications subject to change without notice.

2. All dimensions in inches (mm), tolerance is ±0.02” (±0.5mm).

3. Mounting holes M1 and M2 should be grounded for EMI purposes.

4. Mounting hole M1 is safety ground connection.

5. Specifications are for convection rating at factory settings at 115 Vac input, 25°C unless otherwise stated.

6. Warranty: 2 year

7. Weight: 0.75 lb/0.34 kg

0° to 50°C ambient. Derate each output 2.5% per degree from 50° to 70°C, -20°C startup

Designed to meet IEC 801, -2, -3, -4, -5, -6, Level 3

Power Derating Curve

80W

30 CFM Forced Air Cooling

60W

Output

Power

(Watts)

40W

20W

0W

0°C

10°C 20°C 30°C 40°C 50°C 60°C 70°C

Natural

Convection

Cooling

TA – Ambient Temperature – °C

40W

30W

Phone: [phone]
Email: [e-mail]
www.solahd.com