Snapper P/N 7078273, Z-Vac, 7078273, 7078274, 7063375 Operator's Manual

Actual product may differ from product pictured above
Blower Kit Bagger Kit
Weight Kit
Modelscovered:
P/N 7078273 PIN 0-50576 P/N 7078274
Manual No. 7100056 (I.R. 03/31/05)
Complete Kit
P/N 7063375
CllnutlnJllflln$!
You have just purchased one of the finest pieces of outdoor power equipment on the market today. If properly cared for, your new Z-Vac Grass Catcher Kit will provide years of dependable service. Please read and follow this instruction man- ual carefully in order to get the most out of your new equipment.
As you carefully unpack your unit, you will find the following items:
1 Blower Kit 1 Bagger Kit
1 Weight Kit 1 Package containing operating manuals and warranty registration
Each product leaves our factory in excellent condition; occasionally, however, some damage may occur during shipment. If any such damage is found upon initial inspection, immediately notify the transport carrier who delivered your machine, as they are solely responsible for such damage, as well as any subsequent adjustments necessary.
Before assembly, please take a moment and record your model number and serial number below for future reference (both numbers are located on the serial tag attached to the blower):
Model number
Serial number
Also be sure to promptly fill out and return the warranty registration enclosed in your manual packet.
Your new unit requires very little assembly. Simply follow the instructions contained within this manual to begin enjoying the benefits of your new unit.
ImPS#TMTI7## CBgJl! Y mttSWl#8 #JIB BgS#f
J$$EmBĀ£1N88R8PELq77N8
TRAINING
-- Read, understand, and follow all instructions in the man-
ual and on the unit before starting. If the operator(s) or mechanic(s) can not read English it is the owner's responsi- bility to explain this material to them.
-- Become familiar with the safe operation of the equipment, operator controls, and safety signs.
--All operators and mechanics should be trained. The owner is responsible for training the users.
-- Only allow responsible adults, who are familiar with the instructions, to operate the unit.
-- Never let children or untrained people operate or service the equipment. Local regulations may restrict the age of the
operator.
-- The owner/user can prevent and is responsible for acci- dents or injuries occurring to themselves, other people or
property.
PREPARATION
-- Evaluate the terrain to determine what accessories and
attachments are needed to properly and safely perform the
job. Use only accessories and attachments approved by
the manufacturer.
-- Wear appropriate clothing including safety shoes, safety glasses and ear protection. Long hair, loose clothing or jew- elry may get tangled in moving parts.
-- Inspect the area where the equipment is to be used and remove all objects such as rocks, toys and wire, which can be thrown by the machine.
-- Use extra care when handling gasoline and other fuels. They are flammable and vapors are explosive. a) Use only an approved container. b) Never remove fuel cap or add fuel with the engine run- ning. Allow engine to cool before refueling. Do not smoke. c) Never refuel or drain the machine indoors.
-- Check that operator's presence controls, safety switches and shields are attached and functioning properly. Do not operate unless they are functioning properly.
OPERATION
-- Never run an engine in an enclosed area.
-- Operate only in the daylight or with good artificial light, keeping away from holes and hidden hazards.
-- Be sure of your footing while using pedestrian controlled equipment, especially when backing up. Walk, don't run.
-- Do not operate in reverse unless absolutely necessary.
Always look down and behind before and while traveling in
reverse.
-- Be aware of the blower discharge direction and do not point it at anyone. Do not operate the blower without hose and bagger hood in place.
-- Never leave a running unit unattended. Always stop
engine before leaving unit.
-- Never operate with guards not securely in place. Be sure all safety features are attached, adjusted properly and func- tioning properly.
-- Never operate with the hose or hood removed or altered.
-- Do not change the engine governor setting or over speed the engine.
-- Stop on level ground, shut off engine before leaving the operator's position for any reason.
-- Stop equipment and inspect impeller blades after striking objects or abnormal vibration occurs. Make necessary repairs before resuming operations.
-- Keep hands and feet away intake and discharge areas.
-- Keep pets and bystanders away.
-- Do not operate the unit while under the influence of alco- hol or drugs.
-- Use caution when crossing roads and sidewalks. Stop engine if not blowing.
-- Use care when loading or unloading the machine into a trailer or truck.
-- Use care when approaching blind corners, shrubs, trees or other objects that may obscure vision.
SLOPE OPERATION
Slopes are a major factor related to loss-of-control and tip- over accidents, which can result in severe injury or death. All slopes require extra caution. If you cannot back up the slope, or if you feel uneasy on it, do not drive on it.
Do
-- Mow up and down slopes, never across face.
-- Remove obstacles such as rocks, tree limbs, etc.
-- Watch for holes, ruts, or bumps. Uneven terrain could overturn the unit. Tall grass can hide obstacles.
-- Keep all movement on the slopes slow and gradual. Do not make sudden changes in speed or direction.
Do Not
-- Do not start or stop on a slope. If tires lose traction, pro- ceed slowly straight down the slope.
-- Do not turn on slopes unless necessary, and then, turn slowly and gradually downhill, if possible.
-- Do not use near drop-offs, ditches, or embankments. The operator could lose footing or balance or blower could sud- denly turn over if a wheel is over the edge of a cliff or ditch, or if an edge caves in.
-- Do not operate on slopes with wet grass. Reduced foot- ing or traction could cause sliding.
-- Do not operate machine on slopes in excess of 10 degrees (18% grade) when equiped with a grass catcher.
-- Do not operate machine without weight kit installed when equiped with a grass catcher.
CHILDREN
Tragic accidents can occur if the operator is not alert to the presence of children. Children are often attracted to the unit
and its activity. Never assume that children will remain where you last saw them.
-- Keep children out of the mowing area and under the watchful care of another responsible adult.
-- Do not allow children or others to ride on the machine, attachment, or towed equipment (even with the blades off).
-- Be alert and turn unit off if children enter the area.
-- Before and during reverse operation, look behind and down for small children.
-- Never allow children to operate the unit.
-- Use extra care when approaching blind corners, shrubs, trees, or other objects that may obscure vision.
EMISSIONS
-- Engine exhaust from this product contains chemicals known, in certain quantities, to cause cancer, birth defects, or other reproductive harm.
-- Look for the relevant Emissions Durability Period and Air Index information on the engine emissions label.
MAINTENANCE AND STORAGE
--Always observe safe refueling and fuel handling practices when refueling the unit after transportation or storage.
-- Always follow the engine manual instructions for storage preparations before storing the unit for both short and long term periods.
--Always follow the engine manual instructions for proper start-up procedures when returning the unit to service.
-- Never store the machine or fuel container inside where there is an open flame, such as in a water heater. Allow unit
to cool before storing.
-- Shut off fuel while storing or transporting. Do not store fuel near flames or drain indoors.
-- Keep all hardware tight and keep all parts in good work- ing condition. Replace all worn or damaged decals.
-- Never tamper with safety devices. Check their proper operation regularly.
-- Clean leaves and debris from mufflers and engine to pre- vent fires. Clean up oil or fuel spillage.
-- Stop and inspect the equipment if you strike an object. Repair, if necessary, before restarting.
-- Never make adjustments or repairs with the engine run- ning unless specified otherwise.
-- Park machine on level ground. Never allow untrained per- sonnel to service machine.
-- Carefully release pressure from components with stored energy. (e.g. springs)
-- Only replace impellers. Never straighten or weld them.
-- Keep hands and feet away from moving parts.
-- Frequently check components and replace with manufac- turer's recommended parts, when necessary.
-- Use only factory authorized replacement parts when mak- ing repairs.
-- Always comply with factory specifications on all settings and adjustments.
-- Only authorized service locations should be utilized for major service and repair requirements.
-- Never attempt to make major repairs on this unit unless you have been properly trained. Improper service proce- dures can result in hazardous operation, equipment dam- age and voiding of manufacturer's warranty.
BLOWER KIT INSTALLATION
STEP 1: Remove pin, rod and spring securing dis-
charge deflector to mower deck, and remove deflector. Store deflector for future use. IMPOR-
TANT: Never operate any mower without a dis- charge deflector or grass catcher securely in
place.
STEP 2: Remove two bolts securing right deck pul- ley guard to mower deck and remove guard. Set bolts aside for future assembly step. Store guard for future use. IMPORTANT: Never operate any mower without a pulley guard securely in place.
STEP 3: Loosen both nuts all the way to end of rod. NOTE: Deck belt tension rod is located under
foor rest of machine. Removing foot rest will aid in accessing rod.
REMOVE
STEP 4: Remove belt from right deck pulley.
Remove nut securing pulley to blade spindle, and remove pulley, replacing with supplied replace- ment pulley. Replace nut, and torque to 70-80 ft- Ibs. NOTE: Nut secures blade bolt in place. Support bolt from beneath while replacing pulley. IMPORTANT: Use gloves when working under deck. Sharp blades can cause injury.
Replace deck belt onto bottom groove of pulley. With deck in lowest cutting position, retighten nuts on deck tension rod until spring length measures
2-5/16".
STEP 5: Set blower against deck discharge. Align holes in blower mount with holes in deck discharge tabs, and secure with rod and pin removed in Step
1. NOTE: Do not include deflector spring in rod
installation.
STEP 6: Pull back on idler tension release handle, and install blower belt around top groove of deck
pulley. NOTE: Make sure belt is not rolled or twisted when installing.
5
REMOVE BOLTS,
HEN REMOVE
OVER
STEP 6a: Remove bolts securing impeller pulley
cover to blower, and remove cover.
STEP 6b: Check to see that blower belt is routed around impeller pulley and idler pulleys after belt is
installed onto deck pulley. Then replace cover. Tighten bolts securely. IMPORTANT: Never oper- ate any mower without a pulley guard securely in
place.
STEP 7: Slip tube of locking pin bracket into blow- er mount, and secure with T-handle pin, making sure pin goes through both upper and lower part of blower mount. Then align base of pin bracket par- allel with rear of deck, and, using bracket as a tem- plate, drill two 7/16" holes through deck. Insert two 3/8-16 x 1" bolts up through deck and bracket, securing with hex flange nuts. Tighten securely. IMPORTANT: Use gloves when working under deck. Sharp blades can cause injury.
STEP 8: Lay supplied pulley guard onto deck.
Align hole in front flange with front mounting hole
in deck, and secure with one of the two bolts securing original guard. Do not tighten yet.
Align side flange of guard with side of deck, and,
using other hole in guard as a template, drill one 9/32" hole in deck and install other bolt. (NOTE: Bolt is self-tapping.) Tighten both bolts securely.
6
STEP9: Installbeltguardbetweenpulleyguard andbeltguardsupportcliponfrontpartofblower mount.Securewith two 5/16nylonwingnuts. Tightennutssecurely.
WEIGHT KIT INSTALLATION
!! Warning: Weight kit must be installed prior to
installing bagger unit. Failure to do so may result in Iongitudal tipping of unit.
STEP 10: Insert the four narrow weight bars
through opening in side of foot rest. Be sure holes in weights are all aligned. Next, insert the two 1/2-
13 x 5 bolts through the five wide weight bars, and lay the wide bars against front of footrest, inserting bolts through holes in narrow bars. Secure with
1/2" split lock washers and nuts. Tighten securely.
I
BAGGER KIT INSTALLATION
STEP 11: Install bumper mount standoffs onto rear
bumper of machine, utilizing existing hardware on machine. NOTE: Invert hardware when installing standoffs, installing bolts out through bumper with nuts facing out.
NOTE: When installing standoffs, be sure that the bumper mount plate mounting holes along the
back bar of the standoffs are located towards the right side of the machine. Refer to the Parts List
section of the manual.
STEP 12: Install bumper mount plate onto stand- offs with four 5/16-18 x 3/4 hex cap screws, secur- ing with four 5/16-18 flange lock nuts. Tighten securely.
Also, install muffler deflector (see inset) onto muf- fler, making sure deflector directs exhaust off to the side of the mower. Fasten with clamp.
IMPORTANT: FAILURE TO INSTALL MUFFLER DEFLECTOR MAY RESULT IN A FIRE.
7
INSERT PIN INTO ROD
HOOK BAGGER FRAME ONTO BUMPER MOUNT
PLATE PINS
STEP 13: Hook bottom of bagger frame onto pins
in bottom of bumper mount plate. Then slide lock- ing rod through aligned holes in bagger flame and bumper mount plate, securing with bridge pin.
CROSS ASSEMBLY
STEP 14: Install cross assembly onto bagger
frame with four 3/8-16 x 3/4 bolts and hex flange lock nuts, tightening securely. Insert bolts back through bagger frame and into cross assembly.
STEP 15: Insert two 5/16-18 x 3/4 bolts through reinforcement plate (not shown; refer to Parts List
- Catcher Mount Group), then through holes in bagger frame. Install cover latch arm onto bolts and secure with hex flange lock nuts, tightening securely. NOTE: Use the leftmost set of holes in the bagger frame when installing arm.
STEP 16: Lay cover assembly on cross assembly.
Align hinges on cross assembly with hinges on
cover, and install one round head pin through each set of hinge holes, securing with a hair pin.
ROUND IHEAD PIN
STEP 17: Slip looped end of cover support cord onto threaded stud on hose adapter assembly.
Secure end of cord with one 3/16" flat washer and
10-32 nyloc nut (not shown). Run nut all the way in
on thread, but leave cord loose enough to swivel.
8
STEP18: Installbagsontocrossassemblyby hookingslotin baghangerontotabsin channel assembly.
STEP19:Closecoverandlockinplacebyhook- inglockknobintoslotincoverlatcharm.
STEP20:Sliponehoseclampontoeachendof hose(usetheclampwiththeblackquick-release knobattheblowerend),andinstallhosebetween blowerandbagger.Makesuretofit hosesfirmly ontoadapters.Tightenclampssecurely.
9
INTRODUCTION
Follow operation and maintenance instructions in the Operator's Manual provided with the Snapper CZT/HZT.
GRASS CATCHER OPERATION
1. Select desired cutting height. Choose a setting that will
not attempt to cut off too much at once, overloading the machine.
2. After starting engine and allowing a brief warm up peri- od, move engine speed control to highest setting.
3. Drive machine to cutting area. Engage blades.
4. Select a slow forward ground speed until familiar with conditions. Do not select a speed that is too fast, caus- ing the machine to become overloaded.
5. The weight of the grass catcher and contents will affect the stability and handling of the machine. Avoid sudden starts and sharp turns. Reduce speed on slopes, and DO NOT operate machine on slopes exceeding 10 degrees (18% grade). Operate machine up and down slopes. DO NOT operate machine across the face of slopes. Turn blades off when traveling up slope.
6. Empty grass catcher bags often to minimize effect on stability and handling. Over filling the catcher bags will reduce performance and cause clogging of the hose,
blower and deck.
7. Do not operate the machine with the Grass Catcher cover open. The entire Grass Catcher must be installed, the cover closed and latched properly before operating.
EMPTYING GRASS CATCHER
1. Empty Grass Catcher bags often to avoid overfilling.
Overfilling reduces performance and causes clogging of hose, blower and deck.
2. Turn blades off. Drive machine to location the clippings are to be dumped. DO NOT operate blades in reverse. If you must back machine to dump clippings in desired
location, LOOK and SEE behind and down for children, pets and hazards before and while backing.
3. Stop motion of machine by returning Motion Control(s) to Neutral (N). Set Park Brake. Stop engine.
4. Unlatch cover and lift. Remove bags and dump debris in desired location.
5. After dumping, to maintain peak performance, check the catcher screen located on the inside of the Cover
Assembly to make sure it is clean and free of any build
up. Clean as required with brush or broom.
6. Close catcher cover and latch.
7. Re-start engine and drive machine to cutting area. Set engine speed to highest setting, engage blades and resume operation.
WARNING
DO NOT attempt to remove any clogs from deck, blow- er, or hose with engine or blade running. STOP engine. STOP blades. Set brake. Remove key. Make sure blades and all rotating components have come to a complete stop before removing any catcher or unclog- ging any catcher component.
IF THE GRASS CATCHER BECOMES CLOGGED
The grass catcher may become plugged if the conditions are too severe, the catcher is overfilled, or the machine is
used improperly. If plugging does occur, attempt the follow- ing:
1. Engine speed too slow - set engine speed control to "FAST" position.
2. Empty catcher bags more often.
3. Clean screen on cover assembly.
4. Ground speed too fast - cut at slower speed.
5. Removing too much grass - raise cutting height, cut partial width, and cut lawn more frequently.
6. Grass is too wet from rain or dew - allow grass to dry.
7. Blades are dull or worn - inspect blades and replace as necessary. Use only genuine SNAPPER replacement
blades.
8. Deck, blower, or hose has clipping build up - clean all clippings from all internal surfaces.
WARNING
DO NOT put fingers or hands inside blower! STOP blades. STOP engine. Remove key. Use only a stick, or other suitable means, to clear the blower of clogs or
other obstructions!
k, WARNING
DO NOT attempt any adjustments, maintenance or repairs with engine running. STOP blades. STOP engine. Remove key.
WARNING
Grass Catcher components are subject to deteriora- I tion. Inspect frequently. Replace worn or damaged I
components immediately. Use only genuine SNAPPER I replacement parts. I
(Continued On Next Page)
10
IFTHEGRASSCATCHERBECOMESCLOGGED (ContinuedFromPreviousPage)
To Clear A Plugged Hose
1. Stop blades. Stop engine. Remove key.
2. After all rotating components (engine, blower, blades) have come to a complete stop, loosen hose clamp at
outlet of blower, and remove hose from blower.
3. Clear any obstructions from hose. If necessary, use a stick to reach into the hose.
4. Reinstall hose to blower and securely tighten hose clamp.
To Clear A Plugged Blower
1. Stop blades and blower. Stop engine. Remove key.
2. After all rotating components have come to a complete stop, loosen the hose clamp at the outlet of the blower.
3. Remove hose from blower.
4. Using a stick or similar object, clear all obstructions from blower. DO NOT INSERT HAND.
5. Reinstall hose to blower and securely tighten hose clamp.
GRASS CATCHER MAINTENANCE Grass Catcher components are subject to wear and deteri-
oration during normal usage. Inspect all components fre- quently for signs of wear and deterioration. Replace worn or damaged components immediately.
2. Catcher. Inspect all catcher components. Replace all worn or damaged parts.
3. Catcher Bags. Check bags often for wear or damage. Replace worn or damaged bags immediately, using only SNAPPER approved replacement bags.
4. Deck, Blower, Hose. Clean grass build up from deck, blower, hose, covers and rear cover screen. To maintain
peak performance make sure screen is clean at each dumping.
5. Hose. Check hose for wear, tears and holes. Replace as needed.
6. Blades. Check blades for sharpness, wear, flatness and damage. Refer to CZT/HZT Operator's Manual for blade wear limits and sharpening/replacement instruc-
tions.
7. Blower. Check blower impeller, blower housing and inlet/outlets for signs of wear and deterioration. Replace
as needed. Check all fasteners and hardware to insure none are missing and all are tightened securely.
Lubricate impeller shaft bearings with 1 to 3 shots of General Purpose grease from a grease gun.
8. Belts. Check belts for wear and fraying. Replace as needed.
9. Idler Arm. Check idler arm to insure it pivots freely and bushings are not worn. Replace worn bushings as
needed.
BEFORE EACH USE
1. Perform pre-start checklist and maintenance as
instructed in the SNAPPER CZT/HZT Operator's Manual and Engine Owner's Manual included with the
machine.
WARNING
Grass Catcher bags used on SNAPPER products are made of woven fab- ric, and are subject to deterioration and wear during normal usage. Check
condition of bags before each use. Immediately replace worn or damaged catcher bags with only bags recommended by SNAPPER. The Grass Catcher is optional equipment on some models.
11
30
18
22
27
25
24
25
26
_25
:\
28
25
24
BLOP_ERUNITGROUP
CZT / HZT Models
* Grease Fitting Orientation
12
SntlllllKl-l/tlc lloilr llnl!SrOUll-
CJT/ETmedel$
Item
1
2
3
4 5
6
7
8 9
10 11
12 13
14 15
16 17
18
19 2O 21 22 23 24 25
26 27
28 29
3O
Part No.
3046782 91121
90183 3021097 44995 91804
14409 10776
3046824 91527
3047253 91601 91218 3046781 3046853
91541 3022832
90839 3031920
3046854 3031919
90613 3046813
3043613 90122
91560 91518 91305
92111 91541
aty
1 1 1 1
1 2 2
1
1
1
1
1
1
1
1 7 2 8 4
1 4 2 2 2 9
1
1
1 3 3
Description
WELDMENT, Blower Belt Guard NUT, 1/2-13 Hex Nyloc
WASHER, 1/2" Flat SAE PULLEY, A Groove Idler, Steel
IDLER STUD (3/8-24 thread) FLAT WASHER, 9/16 Type Narrow FLANGE BEARING, 9/16" I.D. (powdered metal)
RETAINING RING, 1/2" BELT RETAINER, Idler
SCREW, 5/16-18 x 1-1/4" Hex Head Cap, GR5 WELDMENT, Idler Arm
NUT, 5/16-18 Hex Flange Lock SCREW, 1/2-13 x 2-1/2" Hex Head Cap, GR5 WELDMENT, Blower Housing
BACK PLATE, Blower SCREW, 5/16-18 x 3/4" Hex Washer Self-Tap
BEARING, Pillow Block, Blower (includes grease fitting) NUT, 7/16-14 Hex Center Lock, GR5 or B
SCREW, 7/16-14 x 1-1/2" Hex Head Cap, GR5 IMPELLER, Fast Vac Blower (weldment) SCREW, 7/16-14 x 1-1/4" Hex Head Cap, GR5 NUT, 3/8-16 Hex Flange Lock
BELT RETAINER PULLEY, Flat Idler, 2-3/4" O.D.
WASHER, 3/8" Flat SAE SCREW, 3/8-16 x 2-1/4" Hex Head Cap, GR5
NUT, 3/8-24 Hex Nyloc SCREW, 3/8-16 x 2" Hex Head Cap, GR5
U-CLIP, 5/16-18 SCREW, 5/16-18 x 3/4" Hex Washer Self-Tap
13
6
S 4
BLOWER_ G,_JP
CZT 1 _T Mo,de_s
14
apBer l-mc We r mun! 8 #p -
ClT/l medels
Item
1
2
3
4 5
6
7
8 9
10 11
12 13
14 15
16 17
18 19
2O
Part No.
3036323 3037161
91537 3037162 3046806 78298 3027505 3027507
91541 3027508
91304 90613
3032118 91527 91601
90951 3020807
12315
91617
aty
1
1
2
1
1
1
1
1 4
1 2 4
1
1
1 2
1
1
1
Description
BELT, A Section, 91.125" effective length WELDMENT, Belt Cover, Deck NOT USED
WING LOCKNUT 5/16-18 BELT GUARD
PULLEY, Blower Input PULLEY, Spindle
WELDMENT, Blower Mount WELDMENT, Guard Support Bracket
SCREW, 5/16-18 x 3/4" Hex Washer Self-Tap WELDMENT, Deck Mount Bracket
SCREW, 3/8-16 x 1" Hex Head Cap, GR5 NUT, 3/8-16 Hex Flange Lock
WELDMENT, T-Handle Pin SCREW, 5/16-18 x 1-1/4" Hex Head Cap, GR5
NUT, 5/16-18 Hex Flange Lock NUT, 5/16-18 Hex Large Flange Center Lock
SPRING, Idler, Fast Vac KEY, 1/4 Square x 1.44
SCREW, 3/8-16 x 6" Hex Head Cap, GR5
15
t
2
42
\
3
/
/
/
/
26
25
'Z-VAC'
CATCHERGROUP
CZT/HZT Models
16
apper l- ac Catcher8mm-
CH/ medel$
Item
18
2
3
4 5
6
7
8 9
10 11
12 13
14 15
16 17
18
19 2O 21 22 23 24 25
26 27
28 29
3O 31 32 33 34 35
36 37
38 39
40 41
42 43
44 45
Part No.
3046861
1704033 1704180 1704405 1667248 1910531
90922 91702
3021670 90376
3022838 0960367
1703700 1704057
91578
1675707 1703807
90316
1703855
3000847
1672023
90187 91511
3022875 3022833
3022876 91757
91290
15067
1703822 91530 91084
1704507 91702 3046722 90598
91603 90883
91241
1704075 3046774
1704508
1960400 90052
1705876
1933886
Qty.
1
2
1 6 4
1 3
1 5
1 2
1
1 4 2 2 4 2 2 2 4 4
1
1
1
1
1 2
1 5 2
1
1
1 3 5 3 3
1
1
1
1
1
1
1
Description
ASSEMBLY, 2 Bag Cover and Screen
(includes Item No. la, 5, 12, 13, 14, 42, 43, 44, 45) CATCHER TOP, 2 Bag
WINDOW, Cover DECAL, Safety, Grass Bag
CLIP, Canoe WASHER, .188 Rivet
SCREW, #10-32 x 1-1/2 Hex Washer Head Machine w/Nylon Patch WASHER, .19 x .38 x .06 Flat
STRAP, Rubber NUT, #10-32 Hex Nyloc
KNOB PIN, Round Head
SCREEN SEAL, Clip
POP RIVET, 3/16 x .265 Alum. TUBE CLIP, Grass Bag
HANGER, Grass Bag BOLT, 5/16-18 x 3/4" Square Neck Carriage, GR5 HOOP, Grass Bag
GRASS BAG CLAMP, Grass Bag
WASHER, 5/16" Split Lock NUT, 5/16-18 Hex, GR5 or B
HOSE CLAMP, Upper HOSE, Snapper Fast Vac
HOSE CLAMP, Lower, Fast Vac SCREW, #10-24 x 1-1/4" Hex Head Cap, GR5
NUT, #10-24 Hex Nyloc HAIR PIN, 1.6
CROSS ASSEMBLY BOLT, 1/4-20 x 3/4" Carriage
SCREW, 1/4-20 x 3/8" Hex Washer Self-Tap STRAP, Tube Support
WASHER, .191 I.D. Flat WELDMENT, Hose Adapter/Deflector
WASHER, 1/4" Flat NUT, 1/4-20 Hex Nyloc
SCREW, 10F x 7/8" Pan Head Cross Recess POP RIVET, 3/16" SUPPORT, Tube
SEAL, 2 Bag Catcher BRACKET, Seal
SCREW, #10-12 x 5/8" Hex Washer Self-Tap WASHER, 1/4" Split Lock CABLE, Double Loop NUT, Speed
17
See Catcher Group
SNAPPER
'Z-VAC'
1 2
5
FastenstoRearBumperAssemblyof Mower
CATCHERMOUNTGROUP
CZT /HZT Models
11
18
aplmr l-mc CK er mum S lp -
CH/ medel$
Item
1
2
3
4 4a
5 6
7
8 9
10 11
12
Part No.
3046687 91086
91619 3046831
3046829 91318 91601 3046995 50551 91318 91601 3046693
15067 3039122 3039123
Qty.
1 4 4
1
1 2 2
1 2 4 4
1
1
1
1
Description
WELDMENT, Bagger Mount Frame SCREW, 3/8-16 x 3/4" Hex Head Cap, GR5 NUT, 3/8-16 Hex Flange Lock
ARM, Cover Latch
REINFORCEMENT PLATE SCREW, 5/16-18 x 3/4" Hex Head Cap, GR5
NUT, 5/16-18 Hex Flange Lock WELDMENT, Bumper Mounting Plate STANDOFF, Bumper Mount SCREW, 5/16-18 x 3/4" Hex Head Cap NUT, 5/16-18 Hex Flange Lock ROD, Support HAIRPIN, Clip EXHAUST DEFLECTOR (Not Shown) MUFFLER CLAMP (Not Shown)
19
Place Against
Front of Footrest
Slide Through
Opening in
Footrest
WEIGHT BAR GROUP
CZT 1HZT ModeJs
2
20
SnappKZ-I/acWelUMBarSNm-
CH/ medel$
Item
1 2 3 4 5
Part No.
78288 78289
91821 90254 91316
Qty.
5 4 2 2 2
Description
WEIGHT, 27 x 5 x 114" WEIGHT, 27 x 2-1/2 x 114" BOLT, 1/2-13 x 3" Hex Head
WASHER, 1/2" Split Lock NUT, 1/2-13 Hex
21
2
\
5
NOTE: Decals are not to scale.
22
_apmr Z-I/atJeu! 8nip-
CH/_medel$
Item
1 2 3 4 5
Part No.
3046944
1704405 3046850 3046851
3046883
Qty.
1 1 1 1 1
Description
DECAL, Fast-Vac DECAL, Safety, Grass Bag
DECAL, Danger, Fast-Vac DECAL, Warning, Fast-Vac DECAL, Warning, Fast-Vac
23
2 YEAR LIMITED WARRANTY
For two (2) years from purchase date for the original purchaser's residential, non-commercial use, SNAPPER, through any authorized SNAPPER dealer will replace, free of charge (except for taxes where applicable), any part or parts found upon examination by the factory at McDonough, Georgia, to be defective in material or workmanship or both.
For one (1) year from purchase date for the original purchaser's commercial, non-residential use, SNAPPER, through any authorized SNAPPER dealer will replace, free of charge, any part or parts found upon examination by the factory at McDonough, Georgia, to be defective in material or workmanship or both.
For ninety (90) days from purchase date for the original purchaser's rental use, SNAPPER, through any authorized SNAP- PER dealer will replace, free of charge, any part or parts found upon examination by the factory at McDonough, Georgia,
to be defective in material or workmanship or both
All transportation costs incurred by the purchaser in submitting material to an authorized SNAPPER dealer for replace- ment under this warranty must be paid by the purchaser.
This warranty does not apply to certain transmissions, to engines and their components, and batteries, as these items are warranted separately. This warranty does not apply to parts that have been damaged by accident, alteration, abuse, improper lubrication, normal wear, or other cause beyond the control of SNAPPER. This warranty does not cover any machine or component part that has been altered or modified changing safety, performance, or durability.
Batteries have a one (1) year warranty period with free replacement if required for one (1) year from the original purchase date. SNAPPER will not be responsible for any installation cost incurred. The battery warranty only covers original equip- ment batteries and does not cover damage to the battery or machine caused by neglect or abuse, destruction by fire, explosion, freezing, overcharging, improper maintenance, or use of improper electrolyte.
There is no other express warranty. DISCLAIMER OF WARRANTY
Implied warranties, including those of merchantability and fitness for a particular purpose, are limited to two (2) years from purchase date for the original purchaser's residential or other non-commercial use, and one (1) year from purchase for the original purchaser's commercial, non-residential use, and ninety (90) days from purchase for the original purchaser's rental use and to the extent permitted by law, any and all implied warranties are excluded. This is the exclusive remedy. Liabilities for consequential damages, under any and all warranties are excluded.
Some states do not allow limitations on how long an implied warranty lasts, or do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. WARNING: THE USE OF REPLACEMENT PARTS OTHER THAN GENUINE SNAPPER PARTS MAY IMPAIR THE
SAFETY OF SNAPPER PRODUCTS AND WILL VOID ANY LIABILITY AND WARRANTY BY SNAPPER ASSOCIATED WITH THE USE OF SUCH PARTS.
IMPORTANT: Please fill out the SNAPPER Product Registration Card immediately and mail to:
Snapper's Product Registration Center, RO. Box 1379, McDonough, Georgia 30253
24
25
26
27
GrassCatcherKit
forCZT/IlZT
Series0
McDonough, GA 30253 U.S.A.
Manual No. 7100056 (I.R. 03/31/05)
Loading...