Snap-On 1800 PSI ELECTRIC PRESSURE WASHER Instruction Manual
691918
THIS MANUAL CONTAINS IMPORTANT INFORMATION REGARDING SAFETY, OPERATION,
MAINTENANCE AND STORAGE OF THIS PRODUCT. BEFORE USE, READ CAREFULLY AND
UNDERSTAND ALL CAUTIONS, WARNINGS, INSTRUCTIONS AND PRODUCT LABELS. FAILURE TO DO SO
COULD RESULT IN SERIOUS PERSONAL INJURY AND/OR PROPERTY DAMAGE.
IF YOU SHOULD HAVE ANY QUESTIONS OR EXPERIENCE A PROBLEM WITH YOUR SNAP-ON
PRODUCT, DO NOT RETURN THIS PRODUCT TO THE STORE. PLEASE CALL OUR CUSTOMER SERVICE
DEPARTMENT AT 1-888-278-8092. BEFORE YOU CALL, HAVE THE FOLLOWING INFORMATION
AVAILABLE: MODEL No., DATE PURCHASED AND STORE LOCATION. AN ALLTRADE
REPRESENTATIVE CAN RESOLVE YOUR PROBLEM OVER THE
PHONE.
CE MANUEL CONTIENT DES RENSEIGNEMENTS IMPORTANTS CONCERNANT LA SÉCURITÉ, L’UTILISATION,
L’ENTRETIEN ET LE RANGEMENT DE CE PRODUIT. AVANT DE FAIRE USAGE DE CET OUTIL, ASSUREZ-VOUS
D’AVOIR BIEN LU ET COMPRIS L’ENSEMBLE DES AVERTISSEMENTS, MISES EN GARDE, INSTRUCTIONS ET
ÉTIQUETTES DE PRODUIT. LE NON-RESPECT DES INSTRUCTIONS POURRAIT ENTRAÎNER DES BLESSURES
GRAVES OU DES DOMMAGES MATÉRIELS.
SI VOUS AVEZ DES QUESTIONS AU SUJET DE CE PRODUIT SNAP-ON OU S’IL
FONCTIONNE MAL, NE LE
RAPPORTEZ PAS AU MAGASIN OÙ VOUS L’AVEZ ACHETÉ. COMMUNIQUEZ PLUTÔT AVEC NOTRE SERVICE
À LA CLIENTÈLE AU NUMÉRO 1-888-278-8092 (ANGLAIS SEULEMENT). AVANT D’APPELER, VEUILLEZ
AVOIR EN MAIN LES RENSEIGNEMENTS SUIVANTS : LE NUMÉRO DE MODÈLE, LA DATE D’ACHAT ET
L’ADRESSE DU MAGASIN. UN REPRÉSENTANT D’ALLTRADE VOUS AIDERA À RÉSOUDRE VOTRE PROBLÈME
AU TÉLÉPHONE.
SNAP-ON
™
IS A TRADEMARK LICENSED BY SNAP-ON™CORP.,
U.S.A., WHICH DOES NOT MANUFACTURE OR
DISTRIBUTE THIS PRODUCT. CONSUMER INQUIRES SHOULD BE
DIRECTED TO:
SNAP-ON
™
EST UNE MARQUE DE COMMERCE DE SNAP-ON
™
MOTORS CORP., U.S.A., QUI NE FABRIQUE PAS ET NE DISTRIBUE
PAS CE PRODUIT. LES QUESTIONS DES CONSOMMATEURS
DOIVENT ÊTRE ADRESSÉES À :
©COPYRIGHT
2010 ALLTRADE TOOLS, LLC.
1431 VIA PLATA
LONG BEACH, CA 90810-1462 USA
691918 – 1800 PSI Electric Pressure Washer, Aveuse Électrique à
Pression de 1800 lb/poç / 124,1 bar_Rev 10/18/10
FOR CUSTOMER SERVICE
SERVICE À LA CLIENTÈLE
1-888-278-8092
Printed in China
Imprimé en Chine
Conforms to UL STD 1776
Certified to CAN/CSA-C22.2
STD NO. 68-92
1800 PSI ELECTRIC PRESSURE WASHER
INSTRUCTION MANUAL
LAVEUSE ÉLECTRIQUE À PRESSION DE 1800
LB/POÇ / 124,1 BAR
1800 PS
I / 124.1 bar
1.4 GPM / 5.29 LPM
INTRODUCTION
This instruction manual is intended for your benefit. Please read and follow the safety, installation, maintenance and troubleshooting steps described within to ensure
your safety and satisfaction. The contents of this instruction manual are based upon
the latest product information available at the time of publication. The manufacturer reserves the right to make product changes at any time without notice.
GENERAL SAFETY
READ AND FOLLOW ALL INSTRUCTIONS.
Failure to follow all instructions in this manual may result in severe
personal injury or death. Keep this manual and refer to it for Safety
Instructions, Operating Procedures, and Warranty.
SAVE THESE INSTRUCTIONS FOR
FUTURE REFERENCE.
RECOGNIZE SAFETY SYMBOLS, WORDS AND LABELS
The safety instructions provided in this manual are not intended to cover all possible
conditions and practices that may occur when operating, maintaining and cleaning
power tools.
Always use common sense and pay particular attention to all the DANGER,
WARNING, CAUTION and NOTE statements in this manual.
This is the safety alert symbol. It is used to alert
you to potential personal injury hazards. Obey all
safety messages that follow this symbol to avoid
possible injury or death.
DANGER indicates an imminently hazardous
situation which, if not avoided, will result in death
or serious injury.
WARNING indicates a potentially hazardous
situation which, if not avoided, could result in
death or serious injury.
TABLE OF CONTENTS
CONGRATULATIONS! . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
GENERAL SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4
RECOGNIZE SAFETY SYMBOLS, WORDS AND LABELS . . . . . . . . 2-3
IMPORTANT INFORMATION ABOUT THIS MANUAL . . . . . . . . . . . 4
UNPACKING & INSPECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
SAFETY WARNINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6
GENERAL SAFETY RULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6
SAFETY RULES FOR PRESSURE WASHERS . . . . . . . . . . . . . . . . . . . . 6-10
GROUND-FAULT CIRCUIT - INTERRUPTER PROTECTION . . . . . . . 9
GROUNDING INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
EXTENSION CORD USAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
FUNCTIONAL DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
PRESSURE WASHER TERMINOLOGY . . . . . . . . . . . . . . . . . . . . . . . . . 11
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-12
OPERATING THE PRESSURE WASHER . . . . . . . . . . . . . . . . . . . . . . . . 13-16
WATER FLOW ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
USING SPRAY WAND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-15
SHUTTING DOWN PRESSURE WASHER . . . . . . . . . . . . . . . . . . . . 15
USAGE OF CLEANING DETERGENTS . . . . . . . . . . . . . . . . . . . . . . . 15-16
MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16-18
TROUBLESHOOTING GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18-23
SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23-24
1 YEAR LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-26
CONGRATULATIONS!
Thank you for choosing this pressure washer. Our aim is to provide you with quality professional products, and we want you to be totally satisfied with your product
and our Customer Service. If any help or advice is needed, please contact us at
1-888-278-8092. When properly cared for, this product will give you many years of
satisfaction.
1 2
IMPORTANT INFORMATION ABOUT THIS MANUAL
Improper and unsafe use of this Pressure Washer can
result in death, fire and/or bodily injury. This instruction manual contains
important information about product safety. Keep the instruction manual
available for others to read before they use the Pressure Washer.
Improper maintenance and operation are responsible for the majority of accidents
involving gas Pressure Washers. The largest portion of these could be prevented by
recognizing the basic safety rules and precautions. Most accidents can be avoided
if the operator recognizes a potentially hazardous situation before it happens and by
observing appropriate safety rules and procedures as outlined in this manual.
Basic safety precautions are outlined in the SAFETY portion of this manual and
throughout the text in this manual where a potential hazard might occur.
Hazards that MUST be avoided to prevent serious injury follow headers marked DANGER
or WARNING. These same precautions are placed as labels on the tool itself.
NEVER use this Pressure Washer for applications that are NOT specified in this manual.
UNPACKING & INSPECTION
After opening the carton, unpack your new Pressure Washer and related parts &
accessories. Please inspect it carefully for any damage that may have occurred
during transit. If any parts are missing, please contact our Consumer Helpline:
Phone: 1-888-278-8092
Do not operate this Pressure Washer if damaged during
shipment, handling or misuse. Damage may result in bursting, which can
cause serious injury or property damage. All damaged parts must be
repaired or replaced as needed prior to operating this Pressure Washer.
Check to see that all nuts, bolts and fittings are secure before putting this Pressure
Washer into service. If you have any questions, or require assistance with damaged
or missing parts, please contact our Consumer Helpline: Phone: 1-888-278-8092
Please have the serial number, model number, date of purchase, and parts list (with
missing parts identified) available for reference when calling.
MODEL NUMBER:
SERIAL NUMBER:
DATE OF PURCHASE:
CAUTION indicates a potentially hazardous
situation which, if not avoided, may result in
minor or moderate injury.
CAUTION used without the safety alert symbol
indicates a potentially hazardous situation which,
if not avoided, may result in property damage.
NOTE provides additional information that is useful
for proper use and maintenance of this tool. If a NOTE
is indicated, make sure it is fully understood.
In addition to SAFETY ALERTS listed above, there could also be numerous symbols
alerting the operator that specific safety measures are required to safely operate this
tool. Learn these SAFETY SYMBOLS as well as the SAFETY ALERTS to prevent
injury to the operator and to bystanders.
READ OPERATING INSTRUCTIONS: Read and understand tool labels,
safety warnings and precautions in this manual before operating the tool.
Failure to follow WARNINGS could result in serious injury or even death
to the operator or bystanders.
ELECTRICAL SHOCK: This tool produces hazardous electrical voltage.
Read and become familiar with this manual’s WARNINGS and CAUTIONS
so that it is installed and used properly.
WEAR APPROVED EYE PROTECTION: Spray can splash back or propel
objects, including incorrectly attached accessories. Always wear
approved eye protection. Safety glasses must conform to the requirements of American National Standards Institute (ANSI) Z87.1 and provide protection against flying particles from both front and side.
INJECTION HAZARD: Pressure washers can produce fluid streams
severe enough to penetrate animal and human flesh.
SLIPPING and FALLING: Pressure washers produce puddles of slippery
liquid that can result in falls. Kickback from spray wand can result in falls
when using unstable platforms.
43
Always make sure the tool is in the OFF position when making adjustments,
changing parts, or performing any maintenance.
Service must be performed only by qualified repair personnel. Service or
maintenance by unqualified personnel may result in a risk of injury.
Do not use the tool if the power switch does not turn it “ON” or “OFF”. A tool that
cannot be controlled with the switch is dangerous and must be repaired.
Store all maintenance tools away from the immediate area before turning ON
the tool.
Do not overreach. Proper footing and balance is a must at all times while using
tools. Unstable support may lead to personal injury. Do not stand on the tool.
Serious injury could result if the tool tips over or you accidentally contact tool.
When using accessories, consult the owner’s manual provided by the manufacturer. The use of improper accessories may cause risk of injury to yourself and others.
Keep protective guards in place and in proper working condition.
Maintain tools and equipment with care. They will function better and more
safely when kept clean and in good working condition. Keeping the tool clean,
dry, and free of grime will add to its life and performance.
Do not use the tool for applications other than specified.
SAFETY RULES FOR PRESSURE WASHERS
RISK OF INJURY
TO reduce the risk of injury, user must read and understand all
safety instructions and warnings at the beginning of this manual.
Pressure Washer produces fluid pressures and velocities high
enough to penetrate human and animal flesh which could result in
serious injury or amputation.
Ensure all connections are tightened securely. Inspect all hoses to ensure
they are not damaged or kinked. Loose connections or damaged hoses can
result in injection injuries.
Ensure all fittings are properly connected. Pull on connection to ensure fittings are secure. Improperly connected fittings can unexpectedly separate
resulting in injury.
SAFETY WARNINGS
READ ALL SAFETY WARNINGS BEFORE
USING PRESSURE WASHER.
GENERAL SAFETY RULES
People with electronic devices, such as pacemakers, should consult their
physician(s) before using this product. Operation of electrical equipment in close
proximity to a heart pacemaker could cause interference or failure of the pacemaker.
WARNING: This product contains chemicals known to the State of California to
cause cancer and birth defects or other reproductive harm.
Keep work area clean and well lit. Messy areas and cluttered workbenches
invite personal injury and/or property damage. Clear all work areas of unnecessary tools, debris, furniture, etc.
Make sure the work area is well ventilated. Never operate in an enclosed area.
Do not place objects on top or against the tool.
Handle correctly. Always operate according to the instructions provided.
Never allow the tool to be operated by children, individuals unfamiliar with its
operation or unauthorized personnel.
Keep children and visitors away. All children should be kept away from the
work area. DO NOT let children handle the tool. Maintain a safe distance for any
person near the work area.
Childproof the workshop. The use of master switches and padlocks is highly
recommended. Remove starter keys where applicable.
Stay alert, watch what you are doing, and use common sense. Do not stand
on tool. Do not use tool while tired or under the influence of drugs, alcohol
or medication. A moment of inattention while operating the tool may result in
serious personal injury.
Operating any tools or equipment under the influence of drugs, alcohol, or
medication can cause personal injury to yourself and others.
Use the right tool. Use tools properly and for their intended task. Do not force
a small tool to do the job of a heavy-duty tool. Using the right tool to do the
right job will make doing the job safer.
65
NEVER cut or splice the power cord or extension cords.
DO NOT spray electrical apparatus and wiring.
WEAR rubber-soled tennis shoes or other footwear that provides some insula-
tion when operating the Pressure Washer.
COLD water use only.
FOR EITHER INDOOR OR OUTDOOR USE. Store indoors.
DO NOT direct spray toward electrical outlets, switches or products
connected to electrical service. Failure to observe this warning can
result in electrocution resulting in severe electrical shock or burns
and possibly resulting in death.
NEVER run the pressure pump without the water supply connected and turned
on. Non-repairable damage to the pump will occur.
RISK OF FALLING - Pressure washer can create puddles of slippery
solutions that can become hazardous.
ENSURE you stand on a stable surface while operating Pressure Washer. Initial
kickback from engaging spray wand can you to lose your balance and fall resulting in minor to severe injuries.
USE EXTREME CAUTION if you must operate Pressure Washer from a ladder or
scaffolding. Kickback from spray wand can result to loss of balance and result
in a fall that could cause serious injuries.
WHEN cleaning Pressure Washer, ensure there are adequate slopes for drainage so
solutions don’t create puddles around unit that could result in slipping and falling.
RISK OF ELECTROCUTION:
Connect only to properly grounded outlet. Do not remove ground pin.
Inspect cord before using. DO NOT use if the cord is damaged.
Keep all connections dry and off the ground.
DO NOT touch plug with wet hands.
Connect to individual branch circuit only.
This product is provided with Ground Fault Circuit Interrupter built into the
power cord plug. If replacement of the plug or cord is needed, use only identical replacement parts.
NEVER place hands in front of nozzle.
NEVER attempt to attach or remove spray wand or hose fittings while Pressure
Washer system is pressurized.
DO NOT treat fluid injection injuries as a simple cut. Seek immediate medical attention.
HIGH VELOCITY fluid spray can cause objects to break, propelling particles
at high speeds.
ALWAYS wear approved safety glasses when using or doing
maintenance on Pressure Washers.
ALWAYS wear protective clothing to prevent accidental spraying.
DO NOT permanently secure spray wand trigger in open position.
DO NOT use spray wand that does not have a trigger lock or trigger guard in
place and in proper working order.
DO NOT use acids, toxic or corrosive chemicals, poisons, insecticides, flamma-
ble solvents or bleach with Pressure Washer. Use of these chemicals can result
in damage to equipment or serious injury or death.
RISK OF EXPLOSION - Do not spray flammable liquids.
RISK OF INJECTION OR INJURY to persons. Do not discharge stream at persons.
RISK OF INJECTION - Unit will start spraying when trigger is squeezed, if
“ON/OFF” switch is in “ON” position, point gun in safe direction.
GUN KICKS BACK - Firmly hold with both hands.
NEVER allow children to operate a Pressure Washer. Keep children at a safe
distance when an adult is using a Pressure Washer.
NEVER direct spray at Pressure Washer.
NEVER operate the Pressure Washer after it has tripped the GFCI or the main
circuit breaker unless the cause has been identified and resolved.
IF an extension cord must be used, keep the power cord connection out of
any standing water, and use a heavy duty three-wire properly grounded type.
Keep the connection as far away as possible from the item being washed and
any water runoff.
87
EXTENSION CORD USAGE
Extension cords are not recommended for use with this product. Extension cords, if
used, must be properly grounded with a 3-prong plug on one and a 3-hole receptacle
on the other. DO NOT use grounding adapters with an extension cord. Extension
cords must be UL listed and use a minimum of 12 A.W.G. wiring. Extension cords
should never exceed 25 feet in length. Extension cords, that are too long, cause a voltage drop over the extra distance causing the motor to run slower with the possibility of
causing damage to the motor. Using extension cords with smaller than the recommended wire gauge run the risk of getting too hot, melting, and/or causing fires.
FUNCTIONAL DESCRIPTION
PRESSURE WASHER FEATURES:
1.
Gun
2. Adjustable Nozzle
3. Pressure Adjust Collar
4. Wand
5. Trigger
6. Trigger Safety Lock
7. Handle Release Button
8. Gun Holder (Top)
9. Detergent Tank Lid
GROUND-FAULT CIRCUIT - INTERRUPTER PROTECTION
This Pressure Washer is provided with a Ground-Fault CircuitInterrupter (GFCI) built into the plug of the power supply cord. This
device provides additional protection from the risk of electric
shock. Should replacement of the plug or cord become necessary,
use only identical replacement parts that include GFCI protection.
GROUNDING INSTRUCTIONS
The electrical power source for this product MUST be grounded in order prevent
possible electric shock or even death should the tool malfunction or breakdown.
Grounding provides a path of least resistance for electric current thus reducing the
risk of electrical shock. The power source must also use a minimum 20A service
and not used if other power tools on the same circuit are in use.
This product is equipped with a grounded 3-wire power cord with a 3-prong plug.
If the power cord will not fit into the wall plug, an approved adapter can be used as
long as it is connected to the center screw in the wall plate. Never modify the elec-
trical plug by cutting off the grounding prong so it will fit into unapproved, ungrounded electrical receptacles.
If you have questions about hooking up this product, contact a certified electrical
contractor to install the proper circuitry acceptable for this and other power tools you use.
Repair or replace any damaged electrical wiring IMMEDIATELY.
9
UNGROUNDED AC RECEPTACLE
GROUNDED RECEPTACLE
GROUNDING ADAPTER
POWER CORD
POWER CORD
COVERPLATE
MOUNTING SCREW
10. Retractable Handle
11. Pressure Washer
12. GFCI Power Cord (not shown)
13. High Pressure Outlet (not shown)
14. Gun Holder (Bottom)
15. Garden Hose Coupling/Water Inlet
16. On/Off Switch
17. Nozzle Cleaning Needle
18. Pressure Hose
10
PRESSURE WASHER TERMINOLOGY
Following are common terms associated with the use of Pressure Washers:
PSI: Pounds per square inch – common unit measure used for water pressure, air
pressure, hydraulic pressure and pounds of force.
GPM: Gallons per minute (liters per minute [metric]) – common unit measure used
for flow rate of water.
ASSEMBLY
This Pressure Washer requires some assembly. If you have any problems with the
assembly of your Pressure Washer, please call the Pressure Washer helpline at
1-888-278-8092. If calling for assistance, please have the model, revision, and serial number from the data tag available.
1. Using a box cutter, cut open the Pressure Washer carton on top.
2. Carefully remove all items from the box and inspect for completeness (see
Functional Description).
WAND/ GUN CONNECTION
Insert the wand into the gun fitting outlet. Ensure that the threads are aligned
properly and that the connection is
secure. Securely tighten the nut by hand.
PRESSURE HOSE/GUN CONNECTION
Unpack the high pressure hose and connect the metal fitting to the gun inlet.
Ensure that the threads are aligned properly and that the connection is secure.
Securely tighten the nut. Place the gun
into the gun holder on the side of the
Pressure Washer.
PRESSURE HOSE / WASHER CONNECTION
1. Remove and discard the protective
plastic plug from the high pressure outlet.
2. Connect the high pressure hose
plastic fitting to the high pressure
outlet at the lower back of the unit.
Ensure that the threads are aligned
properly and that the connection is
secure. Securely tighten the nut by
hand.
GARDEN HOSE / WASHER CONNECTION
DO NOT run the pump without the water supply connect-
ed and turned on. Damage to equipment resulting from failure to follow this
instruction will void warranty.
1. Before connecting the garden hose to
the Pressure Washer, connect the
garden hose to the water source and
run water through the hose to flush
out any debris. Shut off the water at
the source.
2. Attach garden hose to the Pressure
Washer coupling inlet at the lower
front of the unit. Ensure that the threads are aligned properly and that the connection is secure. Securely tighten the nut by hand. Turn on the water source.
For best result, use a short garden hose (30 ft. or less
length), cold water (less than 100 F) and adequate pressure (no less than 50 PSI).
POWER SUPPLY CONNECTION
KEEP all electrical connections dry and off the ground.
NEVER touch the plug with wet hands.
NEVER cut or remove grounding blade (round longer pin) on GFCI
attachment plug.
1. Connect the Pressure Washer GFCI power cord to
a dedicated electrical outlet.
2. Press the RESET button on the GFCI to ensure its
proper operation.
Outlet capacity must be 120V, 60HZ and minimum 15 AMP.
1211
PRESS
RESET
WATER FLOW ADJUSTMENT
ADJUSTING FOR FAN PATTERN
The angle of spray coming out of the nozzle may be adjusted by rotating the front
of the nozzle (cone). This will vary the spray pattern from approximately a 0°
narrow high impact stream (by turning the nozzle fully to the left) to a 60° wide fan
spray (by turning the nozzle fully to the right).
A narrow stream has high impact force on the cleaning surface and results in maximum deep cleaning in a concentrated area. However, this narrow high impact spray
must be used cautiously, as it may damage some surfaces.
A wide fan pattern will distribute the impact of the water over a larger area, resulting in excellent cleaning action with a reduced risk of surface damage. Large
surface areas can be cleaned more quickly using a wide fan pattern.
ADJUSTING FOR PRESSURE
The Adjustable Pressure Nozzle allows you to vary the pressure of your spray by
turning the end of the nozzle (collar). Turning the collar fully to the right will reduce
the pressure to its minimum. If the Pressure Washer has a detergent tank system
you must use this minimum pressure setting in order to suction detergent.
Turning the collar fully to the left will increase the pressure to its maximum for greatest cleaning efficiency. Turning the collar changes the pressure but not the fan pattern.
Detergent will NOT flow until the Pressure Adjust Collar is
set (turned) to low pressure position.
USING THE SPRAY WAND
To prevent damage to your surface and to select an appropriate working pressure for your application, always start with lowest pressure
setting and continue increasing the pressure until the best work result is
achieved.
USAGE TIPS:
• For most effective cleaning, keep spray nozzle from 8 to 24 inches away from
cleaning surface.
OPERATING THE PRESSURE WASHER
ALWAYS wear approved safety glasses when operating Pressure
Washers. Spray can splash back or propel objects, including
incorrectly attached accessories.
The high pressure stream of water that this equipment produces can cut
through skin and its underlying tissues, leading to possible amputation.
Spray gun traps high water pressure, even when the motor
is stopped and water is disconnected, which can cause injury.
Kickback from spray gun can cause you to fall.
1. For your protection, wear the protective safety glasses (provided).
2. Place the Pressure Washer near the working surface.
Make sure that the water source is turned on and all connections
to the Pressure Washer and Spray Gun are secure and without any water leakage.
3. Carefully remove the gun from its holder.
4. Hold the gun securely with both hands. Point the gun in a
safe direction. Make sure that the gun safety (the button
above the trigger) is unlocked and squeeze the trigger to
allow any air that is trapped inside the unit and hoses to
escape. Continue to squeeze the trigger until a steady
stream of water comes from the nozzle.
14
LOW
LOW PRESSURE
HIGH PRESSURE
CONE
HIGH
WIDE
WIDE
STREAM
PUSH
SQUEEZE
STREAM
COLLAR
PUSH
5. Turn on the ON/Off switch on the front of the Pressure
Washer. NOTE: Motor does not start until trigger is pulled.
6. Point the gun in a safe direction and squeeze the trigger
to start motor and water flow.
Make sure wand is
SECURELY tightened to Gun. If the wand is not
securely locked into place, it could be ejected
under high pressure when operating the gun,
possibly causing injury or damage.
13
Wetting the surface first is not recommended, as it dilutes
the detergent and reduces its cleaning ability.
7. Allow detergent to "soak in" for 3-5 minutes before washing and rinsing.
Reapply as needed to prevent surface from drying. Do Not allow detergent to
dry on surface (prevents streaking).
TO RINSE:
1. Reset the Pressure Adjust Collar to high pressure, press the trigger and wait for
the detergent to clear.
2. Keep the spray gun a safe distance from the area you plan to spray.
3. Apply a high pressure spray to a small area, and then check the surface for
damage. If no damage is found, it is okay to continue cleaning.
4. Start at the top of the area to be rinsed, working down with same overlapping
strokes as you used for washing and applying detergent.
When you have completed use of the detergent injection system, continue to run in
low pressure position and flush clean water through the detergent tank until it is
thoroughly cleaned.
Failure to clean properly will cause the injection system to
become clogged and inoperable.
Stop the unit by pressing the ON/OFF button.
Disconnect electrical plug.
Turn off water and depressurize unit by squeezing trigger.
CLEANING TIPS:
• Never leave the Pressure Washer unattended while it is plugged into an electrical outlet and while water is supplied to the equipment.
• Never use the Pressure Washer water inlet to siphon detergent or wax.
• If you have the nozzle too far away from the surface being washed, the cleaning
will not be as effective.
IMPORTANT: DO NOT get closer than 6 inches when cleaning.
MAINTENANCE
Regular maintenance will improve performance and extend life of Pressure Washer.
Pressure Washer’s warranty does not cover items that have been subjected to opera-
tor abuse or negligence. Only by maintaining Pressure Washer in accordance with
instructions in this manual will the full value of the warranty be honored.
• If you get spray nozzle too close, especially using high pressure mode, you may
damage surface being cleaned.
• DO NOT get closer than 6 inches when cleaning tires.
SHUTTING DOWN THE PRESSURE WASHER
The Pressure Washer motor runs only when the trigger is engaged. To shut off the
Pressure Washer:
1. Release spray gun trigger.
2. Move unit's ON/OFF switch to OFF position.
IMPORTANT: Releasing the trigger will shut off the motor but does not shut off electrical power to the unit.
3. Turn off water supply.
4. ALWAYS point spray gun in a safe direction and squeeze spray gun trigger to
relieve built up pressure in the unit.
Spray gun traps high water pressure, even when motor is
stopped and water is disconnected.
5. Engage trigger lock on spray gun when not in use. Place the gun in its holder
on the side of the unit.
6. Disconnect GFCI plug from outlet and coil power cord.
USAGE OF CLEANING DETERGENTS
TO APPLY DETERGENT:
1. Select a detergent/cleanser appropriate for the intended application.
2. Prepare detergent solution as recommended by the manufacturer.
3. Remove the detergent tank lid located at the top of the Pressure Washer.
4. Fill tank with prepared detergent solution. A small funnel may help with this
task. Replace the detergent tank lid.
5. Set (turn) the Pressure Adjust Collar to low pressure position.
Detergent will NOT flow until the Pressure Adjust Collar is
set (turned) to low pressure position.
6. Pull spray gun trigger and apply detergent to a dry surface, starting at lower portion of area to be washed and work upward, using long, even, overlapping strokes.
15 16
Loading...