Smooth Fitness V390 User Manual

USER’S MANUAL

V390 Semi Recumbent Bike

USER WEIGHT LIMITATION: 300lbs(136kgs)

SERIAL NUMBER (found on frame):

2 V 390 SEMI-RECUMBENT BIKE

PRECAUTIONS

For future service or related questions:

Please staple your receipt and/or write in the name and phone number of the retail store where you purchased your bike.
Name: ______________________________ Phone Number: ___________________ Receipt: ______________________

Precautions:

WARNING: To reduce the risk of burns, fire, electric shock, or injury to persons, read the following important precautions

and information before operating the bike. It is the responsibility of the owner to ensure that all users of this bike are adequately
informed of all warnings and precautions.

• Use the bike only as described in this manual.

• Place on a level surface. Do not place the bike on any surface that blocks air openings. To protect the floor or carpet from

damage, place a mat under the bike.

• When choosing a location for the bike be sure that the location and position permit access to a plug.

• Keep the bike indoors, away from moisture and dust. Do not put the bike in a garage or covered patio, or near water.

• Do not operate the bike where aerosol products are used or where oxygen is being administered.

• Keep children under the age of 12 and pets away from the bike at all times.

• The bike should not be used by persons weighing more than 300LBS (136 Kgs).

• Never allow more than one person on the bike at a time. Wear appropriate exercise clothing when using the bike. Do not

wear loose clothing that could become caught in the bike. Athletic support clothes are recommended for both men and
women. Always wear athletic shoes. Never use the bike with bare feet, wearing only stockings, or in sandals.

• When connecting the power cord, plug the power cord into a grounded circuit.

• Always examine your bike before using to ensure all parts are in working order.

• Allow the bike to come to a full stop before stepping off.

• Never insert any object or body parts into any opening.

• Follow the safety information in regards to plugging in your bike.

• The item is suitable for semi-commercial, light-commercial and home usage.

• Keep the power cord away from the incline wheels and do not run the power cord underneath your bike. Do not operate

the bike with a damaged or frayed power cord.

• Always unplug the bike before cleaning and/or servicing. Service to your bike should only be performed by an authorized
service representative, unless authorized and/or instructed by the manufacturer. Failure to follow these instructions will
void the bike warranty.

www.smoothfitness.com

PRECAUTIONS

Pour réparations futures ou questions connexes :

.

Please staple your receipt and/or write in the name and phone number of the retail store where you purchased your bike.
Name: ______________________________ Phone Number: ___________________ Receipt: ______________________

AVERTISSEMENT

suivantes et informations importantes avant d'utiliser le vélo. Il est de la responsabilité du propriétaire de s'assurer
que tous les utilisateurs de ce vélo sont correctement informés de tous les avertissements et les précautions.

• Utilisez le vélo uniquement comme décrit dans ce manuel.

• Placez-le sur une surface plane. Ne pas placer la moto sur une surface qui bloque les ouvertures d'air. Afin de

protéger le plancher ou le tapis de tout dommage, placez un tapis sous la moto.

• Lorsque vous choisissez un emplacement pour le vélo être sûr que l'emplacement et la position de permettre

l'accès à un bouchon.

• Gardez le vélo de l'intérieur, loin de l'humidité et la pou ss ière. Ne pas mettre la moto dans un garage ou un

patio couvert, ou près de l'eau.

• Ne pas faire fonctionner la moto où des produits aérosols sont uti lisés et où

• Gardez les enfants sous l'âge de 12 ans et les animaux loin de la moto à tout moment.

• Le vélo ne doit pas être utilisé par des personnes pesant plus de 300lbs (136 kg).

• Ne laissez jamais plus d'une personne s ur le vélo à la fois. Porter des vêtements exercice approprié lors de

l'utilisation du vélo. Ne portez pas de vêtements amples qui pourraient se coincer dans le vélo. Les
vêtements de support sont recommandés pour les hommes et les femmes. Portez toujours des chaussures
de sport. Ne jamais utiliser le vélo avec les pieds nus, porter des bas seulement, ou en sandales..

• Lorsque vous branchez le cordon d'alimentation, branchez le cordon d'alimentation dans un circuit à la terre.

• Toujours examiner votre vélo avant de l'utiliser pour s'assurer que toutes les pièces sont en ordre de marche

• Laisser le vélo à venir à un arrêt complet avant ma descente.

• Ne jamais insérer d'objet ou le corps des pièces dans les ouvertures.

• Suivez les consignes de sécurité en ce qui concerne le branchement de votr e vé lo

• Gardez le cordon d'alimentation loin des roues pente et ne pas courir le cordon d'alimentation en dessous de

votre vélo. Ne pas faire fonctionner la moto avec un cordon d'alimentation endommagé ou effiloché.

• Débranchez toujours le vélo avant de le netto yer et / ou d'entretien. Ser vice pour votre moto ne doit être

effectuée par un représentant de service autorisé, sauf autorisation et / ou les instructions du fabricant. Le
non respect de ces instructions annule la garantie de vélo

: Pour réduire le risque de brûlures, d'incendie, d'électrocution ou de bles s ures , lire les précautions

3

l'oxygène est administré.

4 V 390 SEMI-RECUMBENT BIKE

POWER REQUIREMENTS

Power Requirements:

IMPROPER CONNECTION OF THE EQUIPMENT GROUNDING CONNECTOR CAN RESULT IN THE RISK OF AN ELECTRIC
SHOCK. CHECK WITH A QUALIFIED ELECTRICIAN OR SERVICE MAN IF YOU ARE IN DOUBT AS TO WHETHER THE
PRODUCT IS PROPERLY GROUNDED. DO NOT MODIFY THE PLUG PROVIDED WITH THE PRODUCT, IF IT WILL NOT FIT
THE OUTLET; HAVE A PROPER OUTLET INSTALLED BY A QUALIFIED ELECTRICIAN.

This bike can be seriously damaged by sudden voltage changes in your home’s electrical power. Voltage spikes, surges and noise
interference can result from weather conditions or from other appliances being turned on or off. To reduce the possibility of bike
damage, always use a surge protector (not included) with your bike.

Surge protectors can be purchased at most hardware stores. The manufacturer recommends a single outlet surge protector with a
UL 1449 rating as a Transient Voltage Surge Suppressor (TVSS) with a UL suppressed voltage rating of 400V or less and an
electrical rating 120VAC , 15 amps.

This bike must be grounded to reduce the risk of electrical shock. Grounding provides a path of least resistance for electric current,
should the bike malfunction. This bike is equipped with an electrical cord that has an equipment-grounding conductor and a
grounding plug. Always plug the power cord into a surge protector, and plug the surge protector into an appropriate outlet that is
properly installed and grounded in accordance with all local codes and ordinances.

Alimentation :

UN MAUVAIS BRANCHEMENT DU CONNECTEUR DE MISE À LA TERRE DE L ’ÉQUIPEMENT POURRAIT PROVOQUER UN
CHOC ÉLECTRIQUE. EN CAS DE DOUTE, CONSULTER UN ÉLECTRICIEN OU UN RÉPARATEUR QUALIFIÉ POUR SA V OIR
SI LE PRODUIT EST CORRECTEMENT MIS À LA TERRE. NE PAS MODIFIER LA FICHE FOURNIE AVEC LE PRODUIT. SI
ELLE N’ENTRE PAS DANS LA PRISE, FAIRE INSTALLER UNE PRISE APPROPRIÉE PAR UN ÉLECTRICIEN
PROFESSIONNEL.

Ce tapis roulant pourrait être gravement endommagé en cas de changement soudain de tension dans votre alimentation électrique.
Les conditions météorologiques ou la mise sous tension ou hors tension d’autres appareils électriques peuvent provoquer des
pointes de tension, des surtensions ou un brouillage. Pour réduire la possibilité que le tapis soit endommagé, toujours utiliser un
limiteur de surtension (non inclus) avec votre tapis roulant.

Il est possible d’acheter des limiteurs de surtension dans la plupart des quincailleries. Le fabricant recommande un limiteur de
surtension UL 1449 à prise unique comme suppresseur de tension transitoire (TVSS) ayant un taux de suppression de tension de
400 V ou moins et une tension électrique de 110 V C.A., 15 A.
Ce tapis roulant doit être mis à la terre pour réduire le risque de choc électrique. La mise à la terre fournit une voie de moindre
résistance au courant électrique en cas de mauvais fonctionnement du tapis roulant. Ce tapis roulant est équipé d’un cordon
électrique avec un conducteur de mise à la terre et une fiche de mise à la terre. Brancher toujours le cordon électrique dans un
limiteur de surtension et brancher le limiteur de surtension dans une prise appropriée, correctement installée et mise à la terre
conformément à tous les codes locaux et ordonnances.

www.smoothfitness.com

BEFORE YOU BEGIN

Open the boxes:

Open the boxes of your new equipment. Inventory all parts included in the boxes, and Supplied Hardware lists
on pages 7 for a full count of the parts in cluded. If you are missing any parts or have any questions contact us

directly at 888-800-1167

Gather your tools:

Before you begin, make sure that you have gathered all the necessary tools you may require to assemble the unit
properly. Having all of the necessary equipment at hand will save time and make the assembly quick and hassle-free.

Clear your work area:

Make sure that you have cleared away a large enough space to properly assemble the unit. Make sure the space is
free from anything that may cause injury during assembly. After the unit is fully assembled, make sure there is a
comfortable amount of free area around the unit for unobstructed operation.

Invite a friend:
Some of the assembly steps may require heavy lifting. It is recommended that you obtain the assistance of another

person when assembling this product.
User Weight Limitation:
Please note that there is a weight limitation for this product. If you weigh more than 300LBS (Approx . 136 Kgs). It is

not recommended that you use this product. Serious injury may occur if the user’s weight exceeds the limit shown
here. This product is not intended to support users whose weight exceeds this limit.

Care and maintenance:
The safety level can be maintained only if it is examined for damage and wear.
Replace any defective components immediately and stop all use of the equipment until repaired.

Always take care when mounting the equipment. Straddle the equipment by placing your feet on the straddle rails.
Dismount from the equipment only after all parts have stopped.

Always check the wear and tear components like pulley, belts, etc.…To prevent injury.

5

6 V 390 SEMI-RECUMBENT BIKE

SUPPLIED COMPONENTS / SUPPLIED HARDWARE

This list identifies the major components you will use to assemble this product.

Water Bottle Bracket

Backrest Cover

Square Stopper,

Hex Head Bolt & Nut (M8)

Pull Bar & Fixed Bracket

for Seat Rail

Console Upper Cover Console Bottom Cover Console Sleeve

Front Small Handlebar Upright Sleeve Seat Cushion

Rail Decoration Cover

Pedal Front Stabilizer

Upright Post Assembly &

Mesh Backrest & Mesh

Seat Handlebar Assembly Seat Frame adjusting Handle Rear Stabilizer

Seat Carriage Assembly Main Frame Assembly & Leveler

www.smoothfitness.com

SUPPLIED COMPONENTS / SUPPLIED HARDWARE

This list identifies the major components you will use to assemble this product.

NOTICE:

been pre-assembled

HARDWARE KIT A

Part No. and Description

Q’TY

88 Lock Washer (M8)

4 pcs

90 Washer (8x16x2.0t)

4 pcs

115 Bolt, Socket Head (M8xp1.25x90mm)

4 pcs

HARDWARE KIT B

Part No. and Description

Q’TY

88 Lock Washer (M8)

5 pcs

90 Washer (8x16x2.0t)

5 pcs

97 Screw, Pan Head (M5xp0.8x25mm)

4 pcs

After unpacking the unit, you will notice that the package includes 3 bags o f h ardware (HARDWARE KIT A,
HARDWARE KIT B and HARDWARE KIT C).

Assembly’s Step 1: Using HARDWARE KIT A
Assembly’s Step 2, 4: Using HARDWARE KIT B
Assembly’s Step 7 ~ 9: Using HARDWARE KIT C

Note:

a. Please review below to know the content of each hardware kit (A, B and C)
b. Some small parts may have been pre-attached for shipping. If a part is not in the hardware bag, check to see if it has

The length of all bolts and screws except those with flat heads is

Measured from below the head to the end of the bolt or screw. Flat head
bolts and screws are measured from the top of the head to the end of

the

bolt or screw

7

8 V 390 SEMI-RECUMBENT BIKE

SUPPLIED COMPONENTS / SUPPLIED HARDWARE

This list identifies the major components you will use to assemble this product.

HARDWARE KIT B

Part No. and Description

Q’TY

99 Screw, Round Head (M5xp0.8x15mm)

4 pcs

111 Bolt, Socket Head (M6xp1.0x15mm)
114 Bolt, Socket Head (M8xp1.25x55mm)

4 pcs
1 pcs

HARDWARE KIT C

Part No. and Description

Q’TY

88 Lock Washer (M8)

10 pcs

90 Washer (8x16x2.0t)

10 pcs

93 Self-Tapping Screw, Truss Head (M4x16mm)

1 pc

99 Screw, Round Head (M5xp0.8x15mm)

2 pcs

107 Carriage Bolt (M8xp1.25x50mm)

2 pcs

112 Bolt, Socket Head (M8xp1.25x16mm)

10 pcs

119 Bolt, Hex Head (M10xp1.5x90mm)

1 pc

127 Nylock Nut (M8)

2 pcs

THE FOLLOWING TOOLS ARE INCLUDED FOR ASSEMBLY:

MULTI WRENCH TOOL W/

ALLEN WRENCH

HEX WRENCH

112 Bolt, Socket Head (M8xp1.25x16mm)

113 Bolt, Socket Head (M8xp1.25x40mm)

128 Thin Nylock Nut (M10xp1.5)

4 pcs

4 pcs

1 pc

PHILLIPS SCREW DR I VER
(13 & 15mm)

(17mm x 2 pcs)

(5 & 6 mm)

www.smoothfitness.com

9

COMPLETE PARTS LIST

NO.

Item Name

Q'TY

V390-1

Main Frame

1

V390-2

Front Seat Support B rac ket

1

V390-3

Inner Seat Carriage Slider

1

V390-4

Outer Seat Carriage Slider

1

V390-5

Front Stabilizer

1

V390-6

Rear Stabilizer

1

V390-7

Upright Post

1

V390-8

Front Small Handlebar

1

V390-9

Seat Carriage

1

V390-10

Seat Fixed Stand

1

V390-11

Seat Frame

1

V390-12

Seat Handlebar

1

V390-13

Front Left Chain Cover

1

V390-14

Front Right Chain Cover

1

V390-15

Crank Cover (L&R)

2

V390-16

Rear Left Chain Cover

1

V390-17

Rear Right Chain Cover

1

V390-18

Decoration Cover for Carriage Slider

1

V390-19

Connection Cover

1

V390-20

Left Pedal

1

V390-21

Right Pedal

1

V390-22

Pulley

1

V390-23

Magnet

1

V390-24

Belt 1 V390-25

Pressure Wheel

1

V390-26

Bushing (ψ50.8xψ10)

V390-27

Bushing (ψ60xψ10)

4

V390-28

Slider Sleeve

1

V390-29

Pull Bar

1

V390-30

Tube Decoration Cover for Stabilizer

2

V390-31

Transprtation Wheel (L&R)

2

V390-32

Front Stabilizer End Cap

2

V390-33

Adjusting Rear Stabil iz er End Cap

2

V390-34

Upright Sleeve

1

V390-35

Foam Grip (530mm)

2

V390-36

Square Plug (20x40mm)

1

V390-37

Console Upper Cover

1

2

10 V 390 SEMI-RECUMBENT BIKE

COMPLETE PARTS LIST

NO.

Item Name

Q'TY

V390-38

Console Bottom Cover

1

V390-39

Left Console Sleeve

1

V390-40

Right Console Sleeve

1

V390-41

Mesh Backrest

1

V390-42

Seat Cushion

1

V390-43

Foam Grip (330mm)

2

V390-44

Hand Pulse Sensor (L&R)

2

V390-45

Round Plug (31.8mm)

4

V390-46

Tube Plug (25.4mm)

4

V390-47

Locking Bar

1

V390-48

Left Seat Carriage Cover

1

V390-49

Right Seat Carriage Cover

1

V390-50

Adjusting Handle

1

V390-51

Seat Fixed Wheel

1

V390-52

Roller (37.6mm)

4

V390-53

Square Stopper

4

V390-54

Left Rail Decoration Cover

1

V390-55

Right Rail Decoration Cover

1

V390-56

Flywheel

1

V390-57

Cable

1

V390-58

Fixed Bracket for Motor

1

V390-59

Left Crank

1

V390-60

Right Crank

1

V390-61

Axle for Crank

1

V390-62

Fixed Bracket for Idler

1

V390-63

Upright Cover (L&R)

2

V390-64

Seat Rail

1

V390-65

Fixed Bracket for Seat Rai l

1

V390-66

Adjusting Handle Stand

1

V390-68

Fixing Pin

1

V390-69

Axle for Sliding Track

1

V390-70

Axle for Braking

1

V390-71

Axle for Backrest Tube

1

V390-72

Bearing (6004zz)

2

V390-73

Eye Bolt (40mm)

2

V390-74

Eye Bolt (50mm)

3

V390-75

Tension Bracket

2

www.smoothfitness.com

11

COMPLETE PARTS LIST

NO.

Item Name

Q'TY

V390-76

Bushing (10.2x14x2mm)

1

V390-77

Bushing (10.2x14x10mm)

1

V390-78

Idler Spring

1

V390-79

Spring for Seat Fixed Stand

1

V390-80

Spring for Fixing Pin

1

V390-81

Spring for Adjusting Handle Stand

1

V390-82

Bushing for Seat Fixed Wheel

2

V390-83

Screw Cap

2

V390-84

Bushing (8x12x6.5mm)

4

V390-85

C Ring (20mm)

1

V390-86

Wave Washer

1

V390-88

Lock Washer (M8)

23

V390-89

Washer (6x19x1.5t)

2

V390-90

Washer (8x16x2.0t)

25

V390-91

Washer (10x23x2.0t)

3

V390-92

Washer (21x30x1.0t)

2

V390-93

Self-Tapping Screw, Truss Head (M4x16mm)

9

V390-94

Self-Tapping Screw, Truss Head (M5x18mm)

27

V390-95

Self-Tapping Screw, Flat Head (M4x20mm)

2

V390-96

Bolt, Button Head (M6xp1.0x40mm)

2

V390-97

Screw, Pan Head (M5xp0.8x25mm)

4

V390-98

Screw, Round Head (1/4’’x20mm)

4

V390-99

Nylon-Coated Screw, Round Head (M5xp0.8x15mm)

14

V390-100

Screw, Round Head (M5xp0.8x40mm)

2

V390-101

Bolt, Round Head (M6xp1.0x25mm)

8

V390-102

Bolt, Round Head (M6xp1.0x35mm)

2

V390-103

Bolt, Round Head (M6xp1.0x65mm)

1

V390-104

Screw, Flat Head (M5xp0.8x12mm)

4

V390-105

Bolt, Pan Head (M8xp1.25x15mm)

2

V390-106

Bolt, Pan Head (M8xp1.25x25mm)

4

V390-107

Carriage Bolt (M8xp1.25x50mm)

2

V390-108

Bolt, Button Head (M10xp1.25x35mm)

1

V390-109

Bolt, Hex Head (M10xp1.25x45mm)

1

V390-111

Bolt, Socket Head (M6xp1.0x15mm)

4

V390-112

Bolt, Socket Head (M8xp1.25x16mm)

14

V390-113

Bolt, Socket Head (M8xp1.25x40mm)

4

V390-114

Bolt, Socket Head (M8xp1.25x55mm)

1

12 V 390 SEMI-RECUMBENT BIKE

COMPLETE PARTS LIST

NO.

Item Name

Q'TY

V390-115

Bolt, Socket Head (M8xp1.25x90mm)

4

V390-116

Bolt, Hex Head (M8xp1.25x16mm)

4

V390-117

Bolt, Hex Head (M8xp1.25x105mm)

1

V390-118

Bolt, Hex Head (M8xp1.25x115mm)

2

V390-119

Bolt, Hex Head (M10xp1.5x90mm)

1

V390-120

Bolt, Hex Head (M10xp1.5x115mm)

2

V390-121

Collar Screw (M6)

2

V390-122

Flange Nut (M10)

2

V390-123

Nut (M6)

3

V390-124

Nut (M8)

4

V390-125

Nylock Nut (M6)

6

V390-126

Thin Nylock Nut (M8)

8

V390-127

Nylock Nut (M8)

9

V390-128

Thin Nylock Nut (M10xp1.5)

3

V390-129

Nylock Nut (M10xp1.25)

2

V390-130

Front Connection Wire

1

V390-131

Rear Connection Wire

1

V390-132

Adaptor Connection Wire w/ Nut

1

V390-133

Adaptor

1

V390-134

Sensor Wire w/Stand

1

V390-135

Motor w/ Wire

1

V390-136

Pulse Sensor Wire 1

1

V390-137

Pulse Sensor Wire 2

1

V390-138

Pulse Sensor Wire 3

1

V390-139

Short Extension Pulse Wire

1

V390-140

Pulse Sensor Wire 4

1

V390-141

Square Plug (25x75mm)

1

V390-142

Flange Nut – Black Color (M10)

2

V390-143

Nut (M5)

1

V390-144

Bolt, Button Head (M8xp1.25x16mm)

4

V390-145

Washer (8x26x2.0t)

2

V390-146

Self-Tapping Screw, Button Head (M4x16mm)

4

V390-147

Leveler

1

V390-148

Mesh Backrest Cover

1

V390-149

Lock Washer (M6)

4

V390-150

Water Bottle Bracket

1

V390-151

Bolt, Round Head M5x12mm

2

www.smoothfitness.com

13

PARTS DIAGRAM

MOST OF THE PARTS SHOWN HERE HAVE BEEN PRE-ASSEMBLED

14 V 390 SEMI-RECUMBENT BIKE

PARTS DIAGRAM

MOST OF THE PARTS SHOWN HERE HAVE BEEN PRE-ASSEMBLED.

www.smoothfitness.com

PARTS DISCRIPTION

Console

Front Small Handlebar

Mesh Backrest

Console Sleeve

Pulse

Upright Post

Upright Sleeve

Adjusting
Main Frame

Front Stabilizer

Pedal

Seat Carriage
Pull Pin

Rear Stabilizer

Handle

Assembly

Sensor

Water Bottle
Bracket

15

16 V 390 SEMI-RECUMBENT BIKE

ASSEMBLY

Step 1: Attach the Stabilizers, Leveler and Pedals

Be sure to thread the Leveler (147)

Tighten all bolts and fasteners now

A

Note: the stabilizer is marked with an R to denote the right side.
Caution: Improperly rotating the pedal threads may cause damage to the equipment

A).Attach the front stabilizer to the main frame using 2x M8xp1.25x90mm Socket Head Bolts (115), 2 x M8 Lock
Washers (88) and 2 x 8x16x2.0t Washers (90). Slide the bolts through the front stabilizer and tread them in to the main
frame.
B). Attach the rear stabilizer to the main frame using 2x M8xp1.25x90mm Socket Head Bolts (115), 2 x M8 Lock
Washers (88) and 2 x 8x16x2.0t Washers (90). Slide the bolts through the rear stabilizer and tread them in to the main
frame.
C) Tilt the bike to the side and thread the leveler completely into the frame. You will adjust the leveler after assembly is
complete
D). Attach the right pedal into the right side crank. To tighten, turn the pedal treads clockwise.
E). Attach the left pedal to the left side crank. To tighten, turn the pedal threads counter clockwise

USE HARDWARE KIT

tightly into the Main Frame (1) before
moving to the next page

www.smoothfitness.com

17

ASSEMBLY

STEP 2: Attach the Upright Post Assembly

G) Slide the upright post sleeve down until it attaches to the main frame covers.

Tighten all bolts and fasteners now

B

Note: Do not tighten the upright post bolts until all four bolts are threaded into the post.
Caution: Do not pinch the wires between the frame

A). Slid the upright sleeve (34) on to the upright post assembly.
B). Attach the upright post assembly to t he main frame usi ng 4 x M8xp1.25x16mm socket head bo lts (112), 4 x M8 lock
washers (88) and 4 x 8x16x2.0t washers(90).

C). Connect the Pulse Sensor Wire 3 (138) to the Pulse Sensor Wire 2 (137).
D). Connect the Rear Connection Wire (131C) to the Motor Wire (135).
E). Connect the Rear Connection Wire (131B) to the Sensor Wire (134).
F). Connect the Rear Connection Wire (131A) to the Adaptor Connection Wire (132).

USE HARDWARE KIT

18 V 390 SEMI-RECUMBENT BIKE

ASSEMBLY

STEP 3: Attach the Console and Front Handlebar

Tighten all bolts and fasteners now

Make sure all wires are recessed into the frame. DO NOT trap or pinch the w ires.

A). Attach the console bottom cover (38) to the console upper cover (37) and secure using 4 x M5xp0.8x25mm pan
head screws (97). See Fig.1
B). Remove the 4 x bolts and washers from the front handlebar.

C). Slide the front handlebar through the upright post bracket. Secure the handlebar using 5 x M8xp1.25x16mm button
head bolts (114), 5 x M8 (88) and 5 x 8x16x2.0t washers (90) Tighten all bolts now,
NOTE: One Washer (8x16x2.0t)(90), one Lock Washer (M8)(88), one Bolt, Socket Head (M8xp1.25x45mm)(114) will
be packed into the hardware bag.

www.smoothfitness.com

19

ASSEMBLY

STEP 4: Attach the Console Sleeve Assembly and Water Bottle bracket

B

Tuck the lowest

Tighten all bolts and fasteners now

A). Slide the console sleeve assembly (39) (40) around the upright post.
B) Be certain that the s leeve assembly aligns together properl y and the lowest portion of the console botto m cover is
inside the console sleeve assembly.
C). Secure the two sleeves together usi ng 4 x M5xp0.8x15mm round head screws (99)

D). Remove the pre-installed water bottle bracket screws from the console post
E). Line up the water bottle bracket with the upright post as pictured below.
F). Secure the bracket using the previously removed 2 x M5x12mm (151) round head bolts

portion of the console
bottom cover under
the sleeve assembly’s
lip

USE HARDWARE KIT

20 V 390 SEMI-RECUMBENT BIKE

ASSEMBLY

STEP 5: Attach the Inner Seat Carriage Slider

A). Insert the inner seat carriage slider (3) Into the main frame.
B) Slide the slider up to #5 and insert the pull pin in to the hole making sure the pan passes through the main frame
into the seat slider carriage.
C). Tighten the pull pin clockwise as much as possible.

www.smoothfitness.com

21

ASSEMBLY

STEP 7: Attach the Seat Rail and the Seat Carriage Assembly

F) Tighten all bolts now

C

Fig. 2

Fig. 1

Fig. 3

Fig. 4

Fig. 5

A). Attach the fixed bracket (65) to the rear side of the seat carriage (9) and secure using 4 x M8xp1.25x16mm socket
head bolts (112), 4 x M8 (88) lock washers, and 4 x 8x16x2.0t washers (90).
B). Slide the seat carriage on to the main frame an insert the stopper bolt into hole one pictured below Fig. 3 (note the
stopper is preassembled to the bolt and nut)
C). Insert 2 x M8xp1.25x16mm socket head bolts (112), Lock Washers (M8)(88), and 2 x 8x16x2.0t washers (90)

through the left and right side of hole 2 pictured below Fig 2.
D) Secure the bottom of the front seat carriage to the main frame using 4 x M8xp1.25x16mm socket head bolts (112),

4 x M8 lock washers (88), and 4 x 8x16x2.0t washers (90) Fig. 3 & 4. Do not fully tighten until step 7 is completed.
E) Attach the rear of the seat carriage the inner seat carriage slider and secure using 1 x M10xp1.5x90mm hex head

bolt (119) and 1 x M10xp1.5 thin nylon lock nut (128) See fig. 5.

USE HARDWARE KIT

22 V 390 SEMI-RECUMBENT BIKE

ASSEMBLY

STEP 8: Attach the pulse Sensor , Rail Cover Assembly and Adjuster Handle

C

Fig. 3

A). Attach the Pulse Extension wire (139) in to the connector located on the front bottom side of the seat rail (64). See
fig. 2
B). Attach the left and right covers (54) (55) over the rear of the end of the seat rail.
C). Secure the rail covers together using 2 x M5xp0.8x15mm round head screws (99)and 1 x M4x16mm self-tapping

truss head screws (93)
D). Thread 1 x M8 nut (124) on the adjuster handle stand Fig. 3.
E).Thread the adjuster handle clock wise onto the adjuster handle stand (66) to the preferred position.
F). Turn the M8 nut counter clock wise to lock the adjuster handle in place.

USE HARDWARE KIT

www.smoothfitness.com

ASSEMBLY

STEP 9: Attach the Seat and Handlebar Assembly

C

A). Attach the seat handlebar to the seat frame using 2 x M8xp1.25x50mm carriage bolts (107) and 2 x M8 nylock

nuts(127).
B). Tighten all bolts and nuts now

C). Remove the 4 preinstalled M8 nylock nuts from the seat fixed frame.
D) Attach the seat frame (11) to the seat fixed frame (10) and secure with the 4 M8 nylock nuts
E). Tighten all bolts and buts now.
F). Place the seat cushion (42) on the seat frame (11) and secure with 4 x M8xp1.25x40mm socket head bolts (113)

G). Tighten all bolts now

23

USE HARDWARE KIT

24 V 390 SEMI-RECUMBENT BIKE

ASSEMBLY

STEP 10: Attach the Seat Rail and the Seat Carriage Assembly

Fig. 5

A). Plug in the pulse sensor wire (140) into connector A located on the left side of the seat. See fig. 4.
B). Remove preinstalled 4 x 1/4’’x20mm round head screws (98) and 4 x M6 lock washers (149) from the back side of

the Mesh Backrest (41)

C). Attach the Mesh Backrest (41) to the Seat Frame (11) using 4 x (1/4’’x20mm round head screws (98) and 4 x M6

lock washers (149)
D). Tighten all bolts now
E). Insert the mesh back rest cover (148) into the recessed slot on the back of the seat frame(11). See fig. 5

ASSEMBLY IS NOW COMPLETE. RECHECH TH AT BOLTS ARE TIGHT.

www.smoothfitness.com

25

GENERAL INFORMATION

The power input is located at the lower front of the bike

THE POWER SUPPLY

HOW TO ADJUST THE REAR STABILIZER

a. After placing the equipment in the intended location for use, it may be necessary to level the equipment.
b. To level the equipment turn the dial in the center of the rear stabilizers

HOW TO ADJUST MAIN FRAME’S LEVELER

a. After adjusting the rear end cap stabilizers you may need to adjust

the main frame stabilizer. Turn the stabilizer A clockwise or
counterclockwise to raise or lower. Turn the locking nut clockwise to
lock the stabilizer in plac e

26 V 390 SEMI-RECUMBENT BIKE

GENERAL INFORMATION

HOW TO ADJUST CONSOLE ANGLE

To get the best console angle, it’s suggested to use both hands to hold the upper and
lower end of the console and gently adjust the console angle to the proper position

HOW TO MOVE THE ITEM SAFELY

Hold the Rear Stabilizer (6) up with two hands and tow the item to the
desired place carefully
 Make sure the floor is level while towing the item

www.smoothfitness.com

27

HOW TO ADJUST THE SEAT

GENERAL INFORMATION

a. To adjust the seat distance from the pedals, it’s

suggested to place your feet on each pedal.

b. Use your right hand to lift up the Adjusting Handle

while using your feet to slide the seat distance

(A)
forward or backward until the seat reaches to the
proper position.

c. Release and secure the Adjusting Handle (A). After

releasing the Adjusting Handle (A), push the seat
forward of back until you

hear a “click” sound.

28 V 390 SEMI-RECUMBENT BIKE

GENERAL INFORMATION

THE SEAT ANGLE ADJUSTMENT

a. Adjust The Seal Angle:

1. Determine the seat angle that you prefer. On the Inner Seat Carriage Slider (3) there is a numbered scale from
1 to 5; from 9 to 45 degree (9 degree increment)

2. Loosen the Pull Pin (29) by turning it counter-clockwise

3. Use your one hand to pull the Pull
Pin (29) outward while use the
other hand to put your fingers into
the hand grip, located on the back
of the Rail Cover (54,55), to slide
the Inner Seat Carriage Slider (3)
upward or downward to the proper
seat angle. Release the pin when

the preferred angle is achieved.

4. Make sure the pin on the Pull Pin (29) locks into position then turn
the clockwise to tighten.

b. HORIZONTAL ADJUSTMENT OF THE SEAT:

1. After adjusting the seat angle, you
will need to adjust the seat pad
horizontally.

2. Behind the Seat Carriage Cover
(48, 49), there is a number scale
from 1 to 5. The number is designed to match the number of the Inner Seat
Carriage Slider (3)

3. To adjust the seat horizontally, pull the Locking Pin (47) outward and adj us t the

Seat Cushion (42) upward or downward until the seat is horizontal. Release the Locking Pin (47) to lock the seat.
When the pin click in position the seat is locked.

www.smoothfitness.com

IMPORTANT STEPS

Warning:

Before using this product, please consult your personal physician for a complete physical examination. Frequent and
strenuous exercise should be approved by your doctor first. If any discomfort should result from your use of this
product, stop exercising and consult your doctor. Proper usage of this product is essential. Please read your manual
carefully before exercising.

Avertissement :
Avant d’utiliser de produit, veuillez consulter votre médecin personnel pour un examen médical complet. Des
exercices fréquents et difficiles doivent d’abord être approuvés par votre médecin. Si vous ressentez un malaise par
suite de l’utilisation de produit, arrêtez les exercices et consultez votre médecin. Un usage approprié de ce produit est
essentiel. Veuillez lire attentivement votre manuel avant de commencer les exercices.
Les enfants doivent rester éloignés de l’équipement pendant son utilisation et lorsqu’il est laissé sans surveillance.
Portez toujours des vêtements appropriés pour les exercices, y compris des chaussures d’athlétisme. Ne portez pas
de vêtements amples qui pourraient être pris dans l’appareil durant les exercices.

Please keep all children away from the equipment during use and when equipment is unattended.
Always wear appropriate clothing, including athletic shoes, when exercising. Do not wear loose clothing that could

become caught during exercising.
Make sure that all bolts and nuts are tightened when equipment is in use. Periodic maintenance is required on all

exercise equipment to keep it in good condition.
Before beginning:
How you begin your exercise program depends on your physical condition. If you have been inactive for several

years, or are severely overweight, you must start slowly and increase your time gradually, a few minutes per week.
Initially you may be able to exercise only for a few minutes in your target zone. However, your aerobic fitness will

improve over the next six to eight weeks. Don’t be discouraged if it takes longer. It’s important to work at your own
pace. Ultimately, you’ll be able to exercise continuously for 30 minutes. And the better your aerobic fitness, the
harder you will have to work to stay in your target zone. But remember these essentials:

• Contact your physician before starting a workout or training program. Have your doctor review your training
and diet programs to advise you of a workout routine you should adopt.

• Begin your training program slowly with realistic goals that have been set by you and your doctor.

• Supplement your program with some type of aerobic exercise such as walking, jogging, swimming, dancing

and/or bicycling. Monitor your pulse frequently. If you do not have an electronic heart rate monitor, have your
physician show you the proper way to manually check your pulse by using your wrist or neck. Establish your
target heart rate based on your age and condition.

• Drink plenty of fluids during the course of your routine. You must replace the water content lost from
excessive exercising to avoid dehydration. Avoid drinking large amounts of cold liquids. Fluids should be at
room temperature when consumed.

29

30 V 390 SEMI-RECUMBENT BIKE

MUSCLE CHART

Targeted muscle groups:

The exercise routine that is performed on this product will develop primarily lower body muscle groups. These muscle
groups are shown in gray color on the chart below.

MUSCLE GROUPS

A Shoulder muscles Calf muscles G

B Pectoral muscles Trapezius muscles H

C Bicep muscle Tricep muscles I

D Abdominal muscles Back muscles J

E Forearm muscles Gluteal muscles K

F Quadricep muscles Hamstring muscles L

www.smoothfitness.com

31

STRETCHING ROUTINE

Warm up and cool down:

cool-down exercises on the following pages:

Toe Touch:

Slowly bend forward from

can and hold for 15 counts.

Shoulder Lift:

Lift your right shoulder up

shoulder.

Inner Thigh Stretch:

Sit with the soles of your feet

Hold for 15 counts.

Hamstring Stretch:

Sit with your right leg

left leg extended.

Open your arms to the side

left arm.

Lean against a wall with your

for 15 counts.

Head Roll:

Rotate your head to the right

for one count.

A successful exercise program consists of a warm-up, aerobic exercise, and a cool-down. Do the entire program at least two and
preferably three times a week, resting for a day between workouts. After several months, you can increase your workouts to four or
five times per week.
Warming up is an important part of your workout, and should begin every session. It prepares your body for more strenuous
exercise by heating up and stretching out your muscles, increasing your circulation and pulse rate, and delivering more oxygen to
your muscles. At the end of your workout, repeat these exercises to reduce sore muscle problems. We suggest the warm-up and

your waist, letting your back
and shoulders relax as you
stretch toward your toes.
Reach down as far as you

together with your knees
pointing outward. Pull your
feet as close into your groin
as possible. Gently push
your knees towards the floor.

Side Stretch:

and continue lifting them until
they are over your head.
Reach your right arm as far
upward toward the ceiling as
you can for one count. Feel
the stretch up your right side.
Repeat this action with your

toward your ear for one
count. Then lift your left
shoulder up for one count as
you lower your right

extended. Rest the sole of
your left foot against your
right inner thigh. Stretch
toward your toe as far as
possible. Hold for 15 counts.
Relax and then repeat with

Calf-Achilles Stretch:

left leg in front of the right
and your arms forward. Keep
your right leg straight and the
left foot on the floor; then
bend the left leg and lean
forward by moving your hips
toward the wall. Hold, and
then repeat on the other side

for one count, feeling the
stretch up the left side of your
neck. Next, rotate your head
back for one count, stretching
your chin to the ceiling and
letting your mouth open.
Rotate your head to the left
for one count, and finally,
drop your head to your chest

32 V 390 SEMI-RECUMBENT BIKE

STRETCHING ROUTINE

Read carefully the following before using your bike

♦ Always stretch your muscles before exercise program. Warm up slowly by walking at a slow speed. Increase workout

intensity gradually until you reach your des ired workout pace. Decrease workout intensi t y gradual ly to an easy walk,
allowing your heart rate to decrease to a normal situation.

♦ When starting the bike, always stand with both feet on the step-on side rails.
♦ When finishing, allow the running belt to slow down and come to a complete stop before stepping off.
♦ Wear comfortable, non-restrictive clothing when using the bike. Never wear anything loose, such as baggy sweat pants,

neckties, loose socks or jewelry. Never drape towels on or around the bike during use.

WARNING

If you feel dizzy, nausea, chest pain or other abnormal symptoms, stop immediately. Consult a physician before continuing
use.

AVERTISSEMENT: Si vous vous sentez étourdi, la nausée, la douleur de coffre ou d'autres symptômes anormaux,

s'arrêtent immédiatement. Consultez un médecin avant de continuer l'utilisation.

♦ Always use the handrail when stepping on or off the bike and when changing incline or speed.
♦ This bike is equipped with a safety key – always clip the cord attached to the safety key to a part of your clothing so the

safety key will properly detach from the computer console, thereby stopping the bike.

♦ Wear running or walking shoes with high-traction soles. To avoid injury and unnecessary wear on your bike, be sure

your shoes are free of any debris such as gravel and small rocks.

Before completing an exercise session, always:

1. Allow time to slow your pace, cool down, and reduce your heart rate to a normal level before completing your workout.

2. Grasp the handlebars and press the Speed “?” button. Slow your pace to an easy walk.

3. Ensure the running belt has come to a complete stop before exiting the bike.

WARNING

Turn off and unplug the bike before proceeding with any maintenance or visual inspections. Failure to do so may result in
serious injury. Note: Failure to perform the required periodic and preventati ve maint ena nc e can void your war ranty.

AVERTISSEMENT

Arrêtez et débranchez le tapis roulant avant de procéder à tout l'entretien ou inspections visuelles. Le manque de faire ainsi
peut avoir comme conséquence des dommages sérieux. Note : Le manque d'exécuter l'entretien périodique et préventif
exigé peut vider votre garantie.

At the end of every exercise session, always:

1. Remove the Safety Key from the computer console.

2. Use the master power switch to turn the bike off. The master power switch is located at the right side of frame next to the
electrical cord.

3. Always position and store the electrical cord where is clear from all pathways.

4. Unplug the electrical cord from the electrical outlet. This is especially important if you are not going to use your bike for
extended periods.

5. Wipe all bike surfaces with a dry cloth or towel especially perspiration on the handlebars, con troll panel, running belt or
other bike components.

www.smoothfitness.com

COMPUTER OPERATION

Whether you

want to lose weight, train for a sporting event, or simply maintain a healthy lifestyle, the MY SMOOTH

t and live healthy. The 5

are proven to help you lose weight, improve your health,

and make positive steps to a healthier lifestyle. These five steps combined with the tools built into your

contained in your Smooth

*Not all Smooth Fitness products include the Smooth Customer Care Kit

Congratulations this product is equipped with the MY SMOOTH Virtual Fitness Trainer.
Virtual Fitness Trainer provides the tools, structure and support you need to be fi

simple steps, outlined in the customer care kit*

33

online account, will provide you with a great start toward achieving your goals.
To set up your account, refer to the instructions in the Getting Started Guide

Fitness customer care kit or visit www.my smoothtrainer.com

34 V 390 SEMI-RECUMBENT BIKE

COMPUTER OPERATION

MANUAL

P1 WEIGHT LOSS

P2 NOV. INTERVAL

P3 INT. INTERVAL

P4 MOUNTAIN CLIMB

P5 HILL CLIMB

P6 ROLLING HILLS

P7 GRAD. INTERV AL

P8 PLATEAU

P9 ADV. INTERVAL

P10 LADDER

P11 USER 1

P12 USER 2

P13 H.R.C.

P14 H.R.C. INTERVAL

Take a few minutes



to review the console
layout. Below is an
overview of the
console’s features
and functions

We recommend that



you use the console
to help vary your
workout routine and
keep you focused on
your process toward
your fitness goals.
The console can
become an important
source of motivation
and interest which
will help keep you on
track

Power ON

a. Make sure the item’s adaptor is correctly plugged into the socket
b. Pedaling or pressing any keys to active the console. The console display will then light up with a short bee p sound,

indicating the console will be ready for use

Power Off

The console would automatically shut off after 5 minutes of inactivity

Program List

www.smoothfitness.com

COMPUTER OPERATION

C

will return to POWER ON status.

status.

on the pulse sensors.

onsole Buttons

a. Press START/PAUSE to begin your exercise
b. Press START/PAUSE again to stop and pause all functions during your exercise program. All the data on

the display will then pause.

c. Press START/PAUSE again to resume the program and all the data displayed will continue until the

program has finished.

d. HOLD TO RESET function: Press and hold START/PAUSE, all the data will return to 0 and the console

Press ENTER to confirm the program function (PROGRAM, TIME, HEIGHT, WEIGHT, AGE, TARGET H.R.
and LEVEL in each time interval).

Press UP to increase the values of the program function (PROGRAM, TIME, HEIGHT, WEIGHT, AGE,
TARGET H.R. and LEVEL in each time interval).

Press DOWN to decrease the values of the program function (PROGRAM, TIM E, HEIGHT, WEIGHT, AGE,

TARGET H.R. and LEVEL in each time interval).

35

**The button is only suitable to
use when the USB is plugged
into the console**

 Press MODE to

review

 Hold MODE for a few seconds, to go into Calendar Mode to edit

year/month/date/hour/minute.

 Press Start/ Pause /Hold to reset to return to POWER ON

a. PULSE RECOVERY button measures how quickly you return to a

resting heart rate after exercising. You could use this button to
measure improvement as you get into shape.

b. The console will monitor your pulse for 60 seconds and calculate a

HEART RATE RECOVERY value from F1.0 to F6.0. F1.0 is the
Highest; F6.0 is the Lowest (For Reference Only).

c. The readout should only be used as a comparison between workouts. It’s recommended to use right after

any aerobic exercise. Stop exercising before starting this function.

d. Your pulse will be displayed in approximately 5 seconds after the heart symbol “ ” is displayed.

NOTE:

If you don’t hold the HEART RATE SENSORS on the handrails with
both hands properly, the console’s HEART RATE value will show “0”
and the main screen would show “F6.0” after the console counts down
to zero, If the sensor was unable to read your heart rate. Press stop
then press the PULSE RECOVERY button again. Replace your hands

Calendar Mode.

Calendar Mode

36 V 390 SEMI-RECUMBENT BIKE

COMPUTER OPERATION

C

onsole Buttons

Speaker Sound System:

 To enjoy your workout with music, simply connect any MP3/CD player to the LINE IN

jack on the console.

The console is allowed you to use Headphone or Speakers when listening to the music.

Turn the Volume Knob (located on the left side of the console) to adjust the proper sound
level.

To record your exercise and health metrics, you must log on
to www.mysmoothtrainer.com
device. Once complete simply plug in the MY Smooth Virtual Fitness Trainer USB devi ce
to you compatible Smooth Fitness exercise machine. Displayed on the equipment will be
your name, weight height and age. Press “START” button to begin your workout, the
console will record your exercise data automatically, every 20 seconds, to your MY
Smooth Virtual Fitness Trainer USB device. After your exercise session is complete,
insert the MY Smooth
device in to the USB port
of your PC or MAC to
upload your data to The
MY Smooth Virtual Fitness
Trainer online health
management program.
The detailed reports show
your exercise and health
results, trends and recommendations to better achieve and maintain your fitness goals.

. Then sync your MY Smooth Virtual Fitness Trainer USB

www.smoothfitness.com

COMPUTER OPERATION

C

Display range: 0 ~ 9999.

down to 0:00.

: Display POWER SU PPL Y status.

console.

onsole Functions

CALORIES:

 Count Up: Measuring total calories your bod y burned

during exercise.



SPEED:

 Displays the current speed KM/MILE during exercise.

RPM (Rotation Per Minute):

 Display range: 0 ~ 999.

TIME:

 Count Up: If a target time was not selected, TIME will count

up from 0:00 to maximum 99:59 minutes.

 Count Down: If you have set the target time (0:00 ~ 99:00),

the console will count down from that selected target time

37

WATTS:

 Displays the current value of Watt during exercise.
 Display range: 0 ~ 9999.

DISTANCE:

 Count Up: If a target distance was not selected, this woul d

measure the total distance from 0:00 to 999.9 km/mile.

 Count Down: If you have set the target distance, the

console will count down from that selected target distance
down to 0.

HAND PULSE / HEART RATE:
 To display your heart rete you must wear the chest belt or

place both of your hands on the Pulse Senso rs located on
the Handlebars. Your pulse will be displayed
approximately 5 seconds after the heart symbol “
displayed.

 If you do not wear the chest belt or place your hands

correctly on the pulse sensors, the computer will shut off
the pulse circuit. To reactivate the pulse feature, properly
place your hands back on the Pulse Sensors and the pulse
readout will appear again.

” is

: When the MY SMOOTH USB is plugged into the

console, the USB signal will be displayed on the

38 V 390 SEMI-RECUMBENT BIKE

COMPUTER OPERATION

GENDER:

 Display range:

Male:
Female:

AGE:
 Display range:

HEIGHT:

 Display range:
3 FEET 4 INCHES ~ 7 FEET; 1 INCH increments / 101 ~ 214
CM; 1 CM increments; the product is not recommended for

use by children.

WEIGHT:

 Display range:
45 ~ 400LBS; 1 LB increments / 20 ~ 181 KGS; 1 KG
increments; the product is not recommended for use by

children.

10 ~ 99 years old; in 1 year increments

NOTE: Although the console allows input for ag e
beginning at 10 years old, the product is not
recommended for use by children.

TARGET H.R.:

 Display range:

50 ~ 180 BPM (beats per minute) ; 1 BPM increments.

www.smoothfitness.com

39

COMPUTER OPERATION

QUICK START:

ENTER the USER DATA

or

“1” Press any button on the console to turn on the console

a. Make sure that the power cord is properly plugged into the socket.
b. The console would automatically shut off after 5 minutes of inactivity.
c. Press any button on the console or begin pedaling to turn on the console. After a few seconds, the console will then

light up with a short beep sound, indicating the console will be ready for use.

“2””Start Pause” button, as an easy way to reset the computer and enter into POWER ON status

Hold the
returning all workout values to zero, and enter into POWER ON status.

START/PAUSE button for a few seconds to reset the computer and

POWER ON status

3” MANUAL PROGRAM

“A.“ENTER MANUAL PROGRAM”

Pressing When in Power on status
press the start button to immediately
start a manual program

Press the UP or Down Button until MANUAL
is displayed. Press Enter to confirm. Once the
MANUAL program has been chosen you will
enter your personal information by following
the directions on the next page.

40 V 390 SEMI-RECUMBENT BIKE

COMPUTER OPERATION

a. After pressing

UP or Down button to enter into MANUAL PROGRAM press ENTER to Confirm, the GENDER

“B. SET YOUR GENDER“

function mode will appear with

b. Use UP or DOWN buttons to set your gender (Male: or Female: ).
c. Press the ENTER button to confirm.

/Male icon display flashing.

“C. SET YOUR AGE“

a. The AGE function will appear with the AGE display flashing.
b. Use the

INCREMENTS).

c. Press the ENTER button to confirm .NOTE: Although the console allows input for age

beginning at 10 years old, the product is not recommended for use by children

UP or DOWN buttons to set your AGE (10 ~ 99 YEARS OLD; in 1 YEAR

“D. SET YOUR HEIGHT“

a. The HEIGHT function will appear with the HEIGHT display flashing.
b. Use the

FEET; 1 INCH INCREMENTS/ 101 ~ 214 CM; 1 CM INCREMENTS).

c. Press the
NOTE for HEIGHT: The product is not recommended for use by children

NOTE for WEIGHT: The product is not recommended for use by children

ENTER button to confirm.

“E. SET YOUR WEIGHT“

a. The WEIGHT func tion wil l appe ar with the WEIGHT display flashing.
b. Use the

LBS/KG INCREMENTS).

c. Press the

UP or DOWN buttons to set your WEIGHT (45 TO 400 LBS / 20 TO 181KGS; 1

ENTER button to confirm.

UP or DOWN buttons to set your HEIGHT (3 FEET 4 INCHES ~ 7

www.smoothfitness.com

COMPUTER OPERATION

“F. SET THE TIME“

a. The TIME function will appear with the TIME display flashing.

NOTE for TIME:

 Count Up: If a target time was not selected, the TIME will count up from 0:00 to a maximum of 99:59 minutes
 Count Down: If you have set the target time, the console will count down from that selected target time to

0:00

b. Use the

INCREMENTS).

c. Press the

“G. START TO EXERCISE”

Press

“H. CHANGING THE RESISTANCE SETTING”

You can change the resistance level (from 1 to 16 levels) at any time during
workout by pressing the

UP or DOWN button

UP or DOWN buttons to set the desired TIME (00:00 TO 99:00; 1 MINUTE

ENTER button to confirm.

START/ PAUSE to begin your exercise.

41

42 V 390 SEMI-RECUMBENT BIKE

COMPUTER OPERATION

“C

ONSOLE INSTRUCTIONS – PROGRAM (P2 ~ P10)”

“A.“ENTER THE PRESET PROGRAMS”

To enter one of the nine preset programs.

a.

Press any button on the console to turn on the console. After a few seconds, the console will then light up with

a short beep sound, indicating the console will be ready for use.

b. Make sure that the power cord is properly plugged into the socket.
c. The console would automatically shut off after 5 minutes of inactivity.
d. Press the UP or DOWN buttons to select program 2 ~ 10 (SEE PROGRAM SELECTION ON PAGE 45)
e. Once the preferred program is displayed press enter to confirm.
f. Enter your USER Data

“B. SET YOUR GENDER”

a. After pressing

UP or Down button to enter into MANUAL PROGRAM press ENTER to Confirm, the GENDER

function mode will appear with

b. Use UP or DOWN buttons to set your gender (Male: or Female: ).
c. Press the ENTER button to confirm.

/Male icon display flashing.

“C. SET YOUR AGE”

a. The AGE function will appear with the AGE display flashing.
b. Use the
c. Press the ENTER button to confirm .NOTE: Although the console allows input for age beginning at 10 years old, the

product is not recommended for use by children.

UP or DOWN buttons to set your AGE (10 ~ 99 YEARS OLD; in 1 YEAR INCREMENTS).

www.smoothfitness.com

COMPUTER OPERATION

“D. SET YOUR HEIGHT”

a. The HEIGHT function will appear with the HEIGHT display flashing.

NOTE for HEIGHT: The product is not recommended for use by children

“E. SET YOUR WEIGHT”

a. The WEIGHT func tion wil l appe ar with the WEIGHT display flashing.
b. Use the

LBS/KG INCREMENTS).

c. Press the
NOTE for WEIGHT: The product is not recommended for use by children

b. Use the

FEET; 1 INCH INCREMENTS/ 101 ~ 214 CM; 1 CM INCREMENTS).

c. Press the

UP or DOWN buttons to set your WEIGHT (45 TO 400 LBS / 20 TO 181KGS; 1

ENTER button to confirm.

UP or DOWN buttons to set your HEIGHT (3 FEET 4 INCHES ~ 7

ENTER button to confirm.

“F. SET THE TIME”

a. The TIME function will appear with the TIME display flashing.
b. Use the

INCREMENTS).

c. Press the

NOTE for TIME:

 Count Up: If a target time was not selected, the TIME will count up from 0:00 to a maximum of 99:59 minutes
 Count Down: If you have set the target time, the console will count down from that selected target time to

0:00

UP or DOWN buttons to set the desired TIME (00:00 TO 99:00; 1 MINUTE

ENTER button to confirm.

43

44 V 390 SEMI-RECUMBENT BIKE

COMPUTER OPERATION

“G. START TO EXERCISE”

START/ PAUSE to begin your exercise.

Press

“H. CHANGING THE RESISTANCE SETTING”

You can change the resistance level (from 1 to 16 levels) at any time during workout by pressing the UP or DOWN button

www.smoothfitness.com

45

COMPUTER OPERATION

P1 WEIGHT LOSS P2 NOVICE INTERVAL

P3 INTERMEDIATE INTERVAL P4 MOUNTAIN CLIMB

P5 HILL CLIMB P6 ROLLING HILLS

P7 GRADUATING INTERVAL P8 PLATEAU

P9 ADVANCED INTERVAL P10 LADDER

46 V 390 SEMI-RECUMBENT BIKE

COMPUTER OPERATION

“CONSOLE INSTRUCTIONS – PROGRAM (P11 ~ 12)”

P11 USER 1 P12 USER 2

“1” To enter one of the 2 USER programs.

a. Press any button on the console to turn on the console. After a few seconds, the conso le will then light up with

a short beep sound, indicating the console will be ready for use.

b. Make sure that the power cord is properly plugged into the socket.
c. The console would automatically shut off after 5 minutes of inactivity.
d. Press the UP or DOWN buttons to select program 11~12
e. Once the preferred program is displayed press enter to confirm.
f. Enter your USER Data

“B. SET YOUR GENDER”

a. After pressing

UP or Down button to enter into MANUAL PROGRAM press ENTER to Confirm, the GENDER

function mode will appear with

b. Use UP or DOWN buttons to set your gender (Male: or Female: ).
c. Press the ENTER button to confirm.

/Male icon display flashing.

www.smoothfitness.com

COMPUTER OPERATION

”C. SET YOUR AGE”

a. The AGE function will appear with the AGE display flashing.
b. Use the
c. Press the ENTER button to confirm .NOTE: Although the console allows input for age beginning at 10 years old,

the product is not recommended for use by children

“D. SET YOUR HEIGHT”

“E. SET YOUR WEIGHT”

UP or DOWN buttons to set your AGE (10 ~ 99 YEARS OLD; in 1 YEAR INCREMENTS).

a. The HEIGHT function will appear with the HEIGHT display flashing.
b. Use the

FEET; 1 INCH INCREMENTS/ 101 ~ 214 CM; 1 CM INCREMENTS).

c. Press the
NOTE for HEIGHT: The product is not recommended for use by children

a. The WEIGHT func tion wil l appe ar with the WEIGHT display flashing.
b. Use the

LBS/KG INCREMENTS).

c. Press the
NOTE for WEIGHT: The product is not recommended for use by children

UP or DOWN buttons to set your WEIGHT (45 TO 400 LBS / 20 TO 181KGS; 1

ENTER button to confirm.

UP or DOWN buttons to set your HEIGHT (3 FEET 4 INCHES ~ 7

ENTER button to confirm.

47

48 V 390 SEMI-RECUMBENT BIKE

COMPUTER OPERATION

“F. SET THE TIME”

a. The TIME function will appear with the TIME display flashing.

NOTE for TIME:

 Count Up: If a target time was not selected, the TIME will count up from 0:00 to a maximum of 99:59 minutes
 Count Down: If you have set the target time, the console will count down from that selected target time to

0:00

G. START TO EXERCISE”

b. Use the

INCREMENTS).

c. Press the

Press

UP or DOWN buttons to set the desired TIME (00:00 TO 99:00; 1 MINUTE

ENTER button to confirm.

START/ PAUSE to begin your exercise.

“H. CHANGING THE RESISTANCE SETTING”

You can change the resistance level (from 1 to 16 levels) at any time during workout by pressing the UP or DOWN button

“2” Programming the 2 USER programs.

a. Once the USER data has been entered press the UP or DOWN buttons to adjust the level of the first segment.
b. Press enter to confirm and move to the next segment
c. Repeat this process until the preferred program has been completed.
d. Press start to save and begin the program
e. This program can be overwritten at any time in the set up screen.

www.smoothfitness.com

COMPUTER OPERATION

“1” Prior information: Press any button on the console to turn on the console

a. Make sure that the power cord is properly plugged into the socket.
b. The console would automatically shut off after 5 minutes of inactivity.
c. Press any button on the console to turn on the console. After a few seconds, the console will then light up with a

short beep sound, indicating the console will be ready for use.

“2” Prior information: ”HOLD TO RESET” button, an easy way to reset and enter into POWER

ON status

Continue pressing
button a few seconds, all the date will
reset to the initial value and the console
will return to POWER ON status.

START/PAUSE

POWER ON status

“3” PROGRAM (P13)

“A. ENTER P13“

UP or DOWN button and then ENTER button:

Press UP or DOWN button to select PROGRAM (P13) and then press ENTER button to confirm and enter

PROGRAM (P13).

“B. SET YOUR GENDER“

UP or DOWN

a. After pressing the

button & then ENTER button:

ENTER button to enter into H. R.C. PROGRAM (P13), the GENDER function mode will

49

appear with

b. Use UP or DOWN buttons to set your gender (Male: or Female: ).
c. Press the ENTER button to confirm your GENDER and enter the mode to set the AGE.

/Male icon display flashing.

50 V 390 SEMI-RECUMBENT BIKE

COMPUTER OPERATION

“C

H.R.C. P

ONSOLE INSTRUCTIONS –

“C. SET YOUR AGE“

ROGRAM (P13)”

UP or DOWN button & then ENTER button:

a. The AGE function mode will appear with the value of AGE display flashing.
b. Use

c. Press the ENTER button to confirm AGE value and enter the HEIGHT

UP or DOWN buttons to set your personal AGE (10 ~ 99 YEARS OLD; 1

YEAR-O LD INCR EM ENT ).

mode. NOTE: Although the console allows input for age beginning at 10 years
old, the product is not recommended for children’s use

“D. SET YOUR PERSONAL HEIGHT“

UP or DOWN button & then ENTER button:

a. The HEIGHT function mode will appear with the va lu e of HEIGHT

display flashing.

b. Use

c. Press the

NOTE for HEIGHT: The product is not recommended for chi ldren’s use

“E. SET YOUR PERSONAL WEIGHT“

ENTER button to confirm HEIGHT value and enter the WEIGHT mode.

UP or DOWN buttons to set your personal HEIGHT (3 FEET 4

INCHES ~ 7 FEET; 1 INCH increment / 101 ~ 214 CM; 1 CM
INCREMENT).

UP or DOWN button & then ENTER button:

a. The WEIGHT func tion m ode will app ear with the va lu e of WEIGHT display flashing.
b. Use

c. Press the

NOTE for WEIGHT: The product is not recommended for children’s use

UP or DOWN buttons to set your personal WEIGHT (45 TO 400 LBS / 20 TO

181KGS; 1 LBS/KG INCREMENT).

ENTER button to confirm WEIGHT value and enter the TIME mode.

“F. SET THE DESIRED TIME“

UP or DOWN button & then ENTER button:

a. The TIME function mode will appear with the value of TIME display flashing.
b. Use

c. Press the

UP or DOWN buttons to set the desired TIME (00:00 TO 99:00; 1 MINUTE

INCREMENT).

ENTER button to confirm TIME value and enter the TARGET HEART RATE

mode.

www.smoothfitness.com

51

COMPUTER OPERATION

“C

H.R.C. P

ONSOLE INSTRUCTIONS –

“G. SET THE TARGET HEART RATE“

ROGRAM (P13)”

UP or DOWN button & then ENTER button:

a. The TARGET HEART RATE function mode will appear with the value of TARGET HEART

“H. START EXERCISE”

RATE display flashing.

b. Use

(BEATS PER MINUTE; 1 BPM INCREMENT).

c. Press the

UP or DOWN button to set your desired TARGET HEART RATE (50 ~ 180 BPM

ENTER button to confirm TARGET HEART RATE value.

START/ PAUSE button: Press START/ PAUSE to begin exercise.

I. MUST-KNOWN HEART RATE PROGRAM INFO.”

CONSOLE MONITOR YOUR CURRENT PULSE TO COMPARE WITH
SETTING TARGET HEART RATE:

 3 minute WARM UP time: After enter the H.R.C. program, the program will start

begin with 3 minute WARM UP time, during the WARM UP mode, the console
will detects the user’s heart rate through hand pulse sensors or wireless chest
belt. During the WARM UP time,
from 1 ~ 16 levels.

 After the 3-minute warm up is complete, then go into the H.R.C. main program (the time will change to your desired step-

up time, the resistance will return to the Level 1). The console at this time will monitor your actual pulse and adjust the
resistance/torque level automatically to keep your pulse within your TARGET HEART RATE ZONE.

 If you current pulse > (the value of the TARGET HEART RATE + 10), the console would decrease one

resistance/torque level automatically.

 If you current pulse < (the value of the TARGET HEART RATE - 10), the console would increase one resistance/torque

level automatically.

NOTE: During H.R.C. main program, if you do not wear a
chest belt or place your hands correctly on the pulse
sensors, after 30 seconds, the console will display “NO
HEART RATE” message and then turn off the pulse circuit
and stop the program. The console will then di splay an
error message “PAUSE”. Press START button and be sure
to wear a chest belt or place your hands back on the Pulse
Sensors correctly, the pulse readout will appear again an d
continue starting the program.

YOUR

the torque/resistance level is available to adjust

52 V 390 SEMI-RECUMBENT BIKE

COMPUTER OPERATION

“C

H.R.C. I

ONSOLE INSTRUCTIONS –

NTERVAL PROGRAM (P14)”

“1” Prior information: Press any button on the console or begin pedaling to turn on the console

a. Make sure that the power cord is properly plugged into the socket.
b. The console would automatically shut off after 5 minutes of inactivity.
c. Press any button on the console or begin pedaling to turn on the console. After a few seconds, the console will then

light up with a short beep sound, indicating the console will be ready for use.

“2” Prior information: ”HOLD TO RESET” button, an easy way to reset and enter into POWER ON

status

Continue pressing
button a few seconds, al l the date will
reset to the initial value and the console
will return to POWER ON status.

HOLD TO RESET

“3” Normal way to operate PROGRAM (P14)

“A. ENTER P14“

UP or DOWN button and then ENTER button:

Press UP or DOWN button to select H.R.C. INTERVAL PROGRAM (P14) and then press ENTER button to

confirm and enter

a. After pressing the

PROGRAM (P14).

“B. SET YOUR GENDER“

UP or DOWN

ENTER button to enter into H. R.C. INTERVAL PROGRAM (P14), the GENDER function mode

button & then ENTER button:

POWER ON status

will appear with

b. Use UP or DOWN buttons to set your gender (Male: or Female: ).
c. Press the ENTER button to confirm your GENDER and enter the mode to set the AGE.

/Male icon display flashing.

www.smoothfitness.com

53

COMPUTER OPERATION

“C

H.R.C. I

ONSOLE INSTRUCTIONS –

“C. SET YOUR AGE“

NTERVAL PROGRAM (P14)”

UP or DOWN button & then ENTER button:

a. The AGE function mode will appear with the value of AGE display flashing.
b. Use

c. Press the ENTER button to confirm AGE value and enter the HEIGHT

UP or DOWN buttons to set your personal AGE (10 ~ 99 YEARS OLD; 1

YEAR-OLD INCREMENT).

mode. NOTE: Although the console allows input for age beginning at 10 years
old, the product is not recommended for children’s use

“D. SET YOUR PERSONAL HEIGHT“

UP or DOWN button & then ENTER button:

a. The HEIGHT function mode will appear with the va lu e of HEIGHT

display flashing.

b. Use

c. Press the

NOTE for HEIGHT: The product is not recommended for chi ldren’s use

“E. SET YOUR PERSONAL WEIGHT“

ENTER button to confirm HEIGHT value and enter the WEIGHT mode.

UP or DOWN buttons to set your personal HEIGHT (3 FEET 4

INCHES ~ 7 FEET; 1 INCH increment / 101 ~ 214 CM; 1 CM
INCREMENT).

UP or DOWN button & then ENTER button:

a. The WEIGHT func tion m ode will app ear with the va lu e of WEIGHT display flashing.
b. Use

c. Press the

NOTE for WEIGHT: The product is not recommended for children’s use

UP or DOWN buttons to set your personal WEIGHT (45 TO 400 LBS / 20 TO

181KGS; 1 LBS/KG INCREMENT).

ENTER button to confirm WEIGHT value and enter the TIME mode.

“F. SET THE DESIRED TIME“

UP or DOWN button & then ENTER button:

a. The TIME function mode will appear with the value of TIME display flashing.
b. Use

c. Press the

UP or DOWN buttons to set the desired TIME (00:00 TO 99:00; 1 MINUTE

INCREMENT).

ENTER button to confirm TIME value and enter the HIGH TARGET HEART

RATE mode.

54 V 390 SEMI-RECUMBENT BIKE

COMPUTER OPERATION

“C

H.R.C. I

Age

Average Max./High
Heart Rate 75%

20

150 beats per minute

25

146 beats per minute

30

142 beats per minute

35

138 beats per minute

40

135 beats per minute

45

131 beats per minute

50

127 beats per minute

55

124 beats per minute

60

120 beats per minute

65

116 beats per minute

70

112 beats per minute

Reference Table

Age

Target Heart Rate

Rate)

20

120 beats per minute

25

117 beats per minute

30

114 beats per minute

35

111 beats per minute

40

108 beats per minute

45

105 beats per minute

50

102 beats per minute

55

99 beats per minute

60

96 beats per minute

65

93 beats per minute

70

90 beats per minute

Reference Table

ONSOLE INSTRUCTIONS –

“G. SET THE HIGH TARGET HEART RATE“

NTERVAL PROGRAM (P14)”

UP or DOWN

a. The HIGH TARGET HEART RATE function

b. However, if the default value of HIGH TARGET HEART RATE doesn’t

match your need, it’s able to use
your desired HIGH TARGET HEART RATE (70 ~ 180 BPM (BEATS PER

MINUTE; 1 BPM INCREMENT). NOTE: HIGH TARGET HEART RATE
must higher 10 + value of LOW TARGET HEART RATE in order to make this program workable. Make sure that
the setting value of HIGH TARGET HEART RATE is reachable to your ideal health condition as the consol e will
monitor your actual heart rate comparing with HIGH TARGET HEART
RATE to automatically adjust the resistance level.

c. Press the ENTER button to confirm HIGH TARGET HEART RATE value and

enter the LOW TARGET HEART RATE mode.

“H. SET THE LOW TARGET HEART RATE“

mode will appear with the value of HIGH
TARGET HEART RATE display flashing.
NOTE: the default value of HIGH TARGET
HEART RATE is based on 75% of (220 –

your age).

UP or DOWN button to slightly adjust

button & then ENTER button:

UP or DOWN

a. The LOW TARGET HEART RATE function mode

will appear with the value of LOW TARGET

HEART RATE display flashing. NOTE: the
default value of LOW TARGET HEART RATE is
based on 60% of (220 –
your age).

b. However, if the default value of HIGH TARGET HEART RATE doesn’t match

your need, it’s able to use UP or DOWN button to slightly adjust your desired LOW TARGET HEART RATE (50 ~ 160

BPM (BEATS PER MINUTE; 1 BPM INCREMENT). NOTE: LOW TARGET HEART RATE must lower 10 + value of
HIGH TARGET HEART RATE in order to make this program workable. Make sure that the setting value of LOW
TARGET HEART RATE is reachable to your ideal health condition as the console will monitor your actual heart
rate comparing with LOW TARGET HEART RATE to automatically adjust the resistance level.

c. Press the ENTER button to confirm LOW TARGET HEART RATE value.

“I. START EXERCISE”

button & then ENTER button:

START/ PAUSE button: Press START/ PAUSE to begin exercise.

Zone
(60% of Min./Low Heart

www.smoothfitness.com

55

COMPUTER OPERATION

C

H.R.C. I

ONSOLE INSTRUCTIONS –

J. MUST-KNOWN HEART RATE PROGRAM INFO.”

CONSOLE MONITOR will help you reach your ideal LOW & HIGH TARGET
HEART RATE

a. 3 minute WARM UP time: After enter the H.R.C. Interval program, the program

will start begin with 3 minute WARM UP time, during the WARM UP mode, the
console will detects the user ’s heart rate through hand pulse sensors or wireless
chest belt. During the WARM UP time,
adjust from 1 ~ 16 levels. NOTE: During the warm-up time, the console will start
monitoring your actual hear rate to see whether could
match your ideal value of LOW TARGET HEART RATE.

b. After 3-minute warm up time, the console will start

adjusting the resistance level automatically if your actual
heart rate couldn’t reach your ideal value of LOW
TARGET HEART RATE. Once you actual heart rate
match to your ideal value of LOW TARGET HEART
RATE, the resistance level would be fixed for about 2
minutes. NOTE: If your actual heart rate couldn’t reach

to your ideal value of LOW TARGET HEART RATE, the console will keep increasing the resistance level every 15
seconds until your actual heart rate reaches your ideal value of LOW TARGET HEART RATE.

c. Once your actual heart rate is in the LOW TARGET HEART RATE ZONE with another 2-minutes workout, the console

will start increasing the resistance level in order to help your actual heart rate to reach to your ideal value of HIGH
TARGET HEART RATE. Once you actual heart rate match to your ideal value of HIGH TARGET HEART RATE, the
resistance level would be fixed for about 2 minutes. NOTE: If your actual heart rate couldn’t reach to your ideal

value of HIGH TARGET HEART RATE, the console will keep increasing the resistance level every 15 seconds
until your actual heart rate reaches your ideal value of HIGH TARGET HEART RATE.

d. Once your actual heart rate is in the HIGH TARGET HEART RATE ZONE with another 2-minutes workout, the console

will start decreasing the resistance level in order to help your actual heart rate to reach to your ideal value of LOW
TARGET HEART RATE. Once you actual heart rate match to your ideal value of LOW TARGET HEART RATE, the
resistance level would be fixed for about 2 minutes. NOTE: If your actual heart rate couldn’t reach to your ideal

value of LOW TARGET HEART RATE, the console will keep decreasing the resistance level every 15 seconds
until your actual heart rate reaches your ideal value of LOW TARGET HEA RT RATE.

e. The workout method will follow the above method until the workout time is finished.

the torque/resistance level is available to

NTERVAL PROGRAM (P14)”

EXERCISE METHOD

56 V 390 SEMI-RECUMBENT BIKE

LIMITED WARRANTY

991214(1)

Model Name

Frame

Break

Parts & Electronics

Labor

V390 USA only

Lifetime

Lifetime

5 years

2 year

V390 Canada

Lifetime

Lifetime

5 years

1 year

LIMITED HOME USE WARRANTY – SMOOTH FITNESS Bikes Warranty

Warranty Coverage: EVO Fitness and Smooth Fitness, Inc. ("Smooth Fitness") warrants to the original owner that each new product to be free from defects

in workmanship and material, under normal use and conditions.
Period of Coverage: The Warranty on this product runs from the date of original purchase using the following schedule:

Labor: Smooth Fitness will reimburse for labor costs for Two (2) years*. Smooth Fitness reserves the right to either:
Hire and reimburse an independent service technician who will come into the home for the repair,
OR
In the event that there is not an available certified Smooth Fitness service technician, Smooth will send the part directly to the consumer and will pay $75 US
per occurrence for the labor costs of such repair. If multiple repair attempts must be made for one reported problem, Smooth will only reimburse once per
occurrence.

Smooth Fitness reserves the right to inspect damaged parts for misuse. Your Original Receipt is proof of purchase and should be kept with the product
manual. You may be required to show proof of purchase prior to warranty service being initiated.

Remedy Provided by Smooth Fitness: Smooth Fitness will provide a replacement part free of charge if a defect is found during the Warranty period.

Smooth Fitness may at its discretion, choose to provide any of following parts or repair options. In the event that a part is determined in need of replacement,
upon receipt of the part by Smooth Fitness, Smooth Fitness may send out the part by UPS ground or another such carrier directly to the customer’s home.

Any redemption may be by repair or replacement of the affected parts and/or product at the sole discretion of Smooth Fitness, by personnel approved by
Smooth Fitness.

Parts repaired or replaced pursuant to this Warranty shall be warranted for the unexpired portion of the Warranty applying to the original product. Any
technical advice furnished before or after delivery in regard to the use or application of Smooth Fitness products is furnished without charge and on the basis
that it represents Smooth Fitness' best judgment under the circumstances but that the advice is used at your sole risk.

Procedure for Obtaining Your Remedy Under This Warranty: To obtain service on a Smooth Fitness product, call Smooth Fitness. In the instance that
service is not available in an area, Smooth Fitness, at its discretion, can either 1) find a service technician in your area to perform warranty service, 2) have a
local dealer perform warranty service, or 3) send the warranty parts to you and reimburse as described above. To help the technician assist you, please
have the following information ready:

• Model name or number from the cover of the manual;

• Serial number located on the frame of the unit; and

• The part description and the order number.

Limitations on Warranty: This Warranty does not cover any problems, damages or failures that are caused by accident, improper assembly, failure to
observe cautionary labels on the product, failure to operate the product correctly, power grid failures or spikes from your local electrici t y provider, abuse or
freight damage. Smooth Fitness does not warrant against any damage or defects that may result from repair or alterations made to the product by an
unauthorized repair facility. In order for this warranty to be valid, all Smooth Fitness and EVO Fitness exercise equipment must be stored and used in a fully
finished and livable room within the residence (not including an indoor swimming pool room).

This Warranty shall terminate if you sell or otherwise transfer this product. This Warranty does not apply to any product shipped or handled outside of the
United States or Canada. This Warranty does not apply if the product is used as a rental product or in commercial use. Consequential and incidental
damages are not recoverable under this Warranty. (Some states do not allow
the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.)

THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER EXPRESS WARRANTIES. ALL IMPLIED WARRANTIES,
INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO TWO (2)
YEARS* FROM THE EFFECTIVE DATE OF THIS WARRANTY. SMOOTH FITNESS IS NOT
LIABLE FOR CONSEQUENTIAL OR INCIDENTA L DAMAGES RESULTING FROM ANY DEFECT IN PARTS NOR FOR
ANY BREACH OF EXPRESS OR IMPLIED WARRANTIES. SMOOTH FITNESS' SOLE LIABILITY UNDER THIS
WARRANTY IS LIMITED TO THE TERMS DESCRIBED IN THIS FORM. THIS WARRANTY GIVES YOU SPECIFIC LEGAL
RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.

*Two year labor is valid only with the continental United States; Canadian labor warranties are valid for the period of 1 year from date of purchase.

FORM WS-1 (rev. 03/2008)

www.smoothfitness.com

57

Smooth Fitness

King of Prussia, PA 19406

Toll Free Customer Service:

1.888.800.1167

Smooth Fitness

King of Prussia, PA 19406

www.smoothfitness.com

Toll Free Customer Service:

1.888.800.1167

www.smoothfitness.com

th

780 5

th

780 5

Website:

Website:

Ave

Ave