Smeg SWM86E, SWM840E, SWM834E User Manual

LAVABIANCHERIA

MANUALE DELL’UTENTE

WASHING MACHINE

USER MANUAL

mode d’emploi de machine

à laver électronique

SWM834E SWM840E

SWM86E

THE CONTENTS

SECTION 1:BEFORE USING

x Safety warnings x Recommendations

SECTION 2:INSTALLATION

x Removal of transportation screws x Adjustment of feet x Electrical connection x Water supply connection x Water drain connection

SECTION 3:TECHNICAL SPECIFICATIONS SECTION 4:CONTROL PANEL

x Start/Pause button x Function indicator lights x Function buttons x Spin speed selector x Program knob

SECTION 5:WASHING YOUR LAUNDRY

x Before washing x Running the machine

SECTION 6:MAINTENANCE AND CLEANING

x Water inlet filters x Pump filter x Detergent drawer x Siphon plug x The cabinet x The drum x Remove of your machine from lime

SECTION 7: PRACTICAL INFORMATION

SECTION 8:AVOIDING MINOR FAULTS

SECTION 9:AUTOMATIC FAILURE DETECTION SYSTEM

SECTION 10:INTERNATIONAL WASHING SIGNS

SECTION 1:BEFORE USING

x x x x

x x x

x x

SAFETY WARNINGS

Do not use a multiple socket or extension cord.

x Do not insert a plug with damaged or broken cord into the socket. x If the cord is damaged it should be replaced by the manufacturer or

appointed service agent in order to avoid a hazard. Never remove the plug from the socket by pulling from the cord section. Remove the plug by holding. Do not plug the power supply with wet hands. Never touch the machine with wet hands or feet. Never open the detergent drawer while the device is running. Never force to open the door of the machine while the machine is running. Since the machine can reach high temperatures while running, do not touch the drain hose and water during draining. In case of any failure, first unplug the device and close the water tap. Do not attempt to repair.Please apply to the nearest authorized service station. Do not forget that the packing material of your machine may be hazardous for children. Do not let your children play with the washing machine. Keep your pet away from your machine. Your machine should only be used by adults within the information written in this manual. Your machine is designed for use in house environment. Warranty will be invalid if you use it for commercial purposes. The appliance should not be put on a carpet which can block the air ventilation on the bottom side.

RECOMMENDATIONS

The detergent or softener in contact with air for a long time will dry and stick to your detergent drawer.To avoid this put your detergent and softener into the detergent drawer just before washing. It is recommended that you use pre-washing program for only very dirty clothes. Please do not exceed the maximum loading capacity. The appliance is not intended for use by people (including children) with reduced physical,sensor yor mental capabilities , or lack of experience and knowledge , unless they have been given supervision or instruction concerning use of the appliance by a preson responsible for their safety.Children should be supervised to ensure that they don’t play with the appliance.

If you will not use your machine for a long time, unplug your machine,

x x

close the water supply and leave the door open in order to keep the inside of the machine dry and for prevention from unpleasant odour. As a result of the quality control procedures, a certain amount of water may remain in your machine. This is not harmful for your machine.

SECTION 2: INSTALLATION

You must pay attention to the following issues before using your washing machine.

REMOVAL OF TRANSPORTATION SCREWS

Transportation screws, which are located at the back side of the machine, must be removed before running the machine. Loosen the screws by rotating counterclockwise by a suitable wrench. (DIAGRAM-1) Remove the screws by pulling them.(DIAGRAM-2) To the holes where the transport screws have been removed, insert the plastic transport screw taps found in the accessories bag. (DIAGRAM-3) The transportation screws, that have been removed from the machine should be kept in hand for any other transportation necessities.

DIAGRAM-2

DIAGRAM-1 DIAGRAM-3

ADJUSTMENT OF FEET

Do not install your machine on rugs or similar surfaces. For your machine to work silently and without any vibration, it should be settled on a flat, non-slippery and tough ground.

You can adjust the balance of your machine from its feet.

x x x

x x

First, loosen the plastic adjustment nut. Adjust by rotating the feet upwards or downwards. After the balance has been reached, tighten the plastic adjustment nut again by rotating it upwards. Never put cartons, wooden blocks or similar materials under the machine to balance the irregularities on the level of the ground.

ELECTRICAL CONNECTION

Your washing machine works with 220-240V and 50Hz. A special grounded plug has been attached to the network cable of your washing machine. This plug must definitely be inserted to a grounded socket with 10 ampere. The fuse flow value of the electricity line attached to this should also be 10 ampere. If you have no such sockets and fuses in your house, let it be made by a qualified electrician.

x Our company will not be responsible for any damages that may

occur as a result of usage without grounding.

x Insert the machine’s plug to a grounded socket which you can

easly reach.

WATER SUPPLY CONNECTION

x Depending on the features your machine,may be with single water

inlet(cold) or double water inlet (cold/hot). The white headed hose is for cold water inlet and red headed hose is for hot water inlet (valid for machines with hot&cold water inlet).

x To prevent leakage from the connection joints, 1 (valid for cold water

inlet) or 2 (valid for machines with hot&cold water inlet) seals are included in the hose packing. Fit these seals at the end of water inlet hoses on the tap side.

x Connect the white headed hose to the water inlet valve with white

filter and connect the red headed hose to the water inlet valve with red filter (latter is valid in machines with hot&cold water inlet). Tighten the plastic parts of the connections with your hand.Please call a qualified plumber for safer connections.

x Water pressure of 0,1-1 MPa from your tap will enable your machine

to work more efficiently.(0,1 MPa pressure means water flow of more than 8 liters in 1 minute from a fully opened tap)

x After connections are completed, check for the non-leakage of the

connection joints by turning on your tap completely.

x Be sure that water inlet hoses are not folded, broken or crushed. x Mount the water inlet hoses to a 3”/4, geared water tap.

Cold water inlet (White filter valve)

Hot water inlet (Red filter valve)

WATER DRAIN CONNECTION

x Be sure that water inlet hoses are not folded, twisted, crushed or

elongated by stretching.

x Water drain hose should be mounted at a height of minimum 60 cm,

maximum 100 cm from the ground.

x The end of the water drain hose may directly be fitted to the dirty

water outlet hole or a special apparatus mounted on the outlet bracket of the wash-stand.

x Never attempt to extend the water drain hose by adding extra parts.

SECTION 3:TECHNICAL SPECIFICATIONS

Maximum dry laundry capacity (kg) Recommended loading (kg)

Height (cm)

Width (cm)) Depth (cm)

Maximum spin cycle ( rpm )

SWM834E SWM840E SWM86E

456

3,5 4,5 5,5

85 85 85

59,6 59,6 59,6

37 42 54

800 800 800

(*) Maximum spin cycles depend on the model you’ve chosen

SECTION 4:CONTROL PANEL

1 2 3 4 5 6

1-Detergent drawer 6-Start/pause light 2-Program knob 7-Program ready light 3-Program end light 8-Function buttons 4-Spin speed s elector 9-Start/pause button 5-Function indicator lights

7 8 9

START/PAUSE BUTTON

Used to start a selected program or pause during running.

WARNING!

It is required for the program knob to be brought to O(off)

position before selecting the program or changing a continuing program.

FUNCTION INDICATOR LIGHTS

When the start/pause button or any function button is pressed,the corresponding light turns on.The light turns off when the function button or start/pause button is re-pressed, or when the process the selected function is completed.

The function indicator lights are also used in failure detection system mentioned in section 9.

FUNCTION BUTTONS

Rinse hold

This function is recommended to be used when the clothes cannot be taken immediately after the end of the program.This will prevent occurrence of wrinkles. When this button is pressed, the last rinsing water is not drained. For the program to continue from the same point, repress the same button.

+ 20 hidden pages