Smeg SWM65 User Manual

FULL ELECTRONIC

WASHING MACHINE

USER MANUAL

THE CONTENTS SECTION 1:BEFORE USING

• Safety warnings

• Recommendations

SECTION 2:INSTALLATION

• Removal of transportation screws

• Adjustment of feet

• Electrical connection

• Water supply connection

• Water drain connection

SECTION 3:TECHNICAL SPECIFICATIONS SECTION 4:CONTROL PANEL

• Start/Pause button

• Function indicator lights

• Function buttons

• Program knob

SECTION 5:WASHING YOUR LAUNDRY

• Before washing

• Running the machine

SECTION 6:MAINTENANCE AND CLEANING

• Water inlet filters

• Pump filter

• Detergent drawer

• Siphon plug

• The cabinet

• The drum

• Remove of your machine from lime

SECTION 7: PRACTICAL INFORMATION SECTION 8:AVOIDING MINOR FAULTS SECTION 9:AUTOMATIC FAILURE DETECTION SYSTEM SECTION 10:INTERNATIONAL WASHING SIGNS

SECTION 1:BEFORE USING

SAFETY WARNINGS

• Do not use a multiple socket or extension cord.

• Do not insert a plug with damaged or broken cord into the socket.

• If the cord is damaged it should be replaced by the manufacturer or

appointed service agent in order to avoid a hazard.

• Never remove the plug from the socket by pulling from the cord section. Remove the plug by holding.

• Do not plug the power supply with wet hands.

• Never touch the machine with wet hands or feet.

• Never open the detergent drawer while the device is running.

• Never force to open the door of the machine while the machine is

running.

• Since the machine can reach high temperatures while running, do not touch the drain hose and water during draining.

• In case of any failure, first unplug the device and close the water tap. Do not attempt to repair.Please apply to the nearest authorized service station.

• Do not forget that the packing material of your machine may be hazardous for children.

• Do not let your children play with the washing machine.

• Keep your pet away from your machine.

• Your machine should only be used by adults within the information

written in this manual.

• Your machine is designed for use in house environment. Warranty will be invalid if you use it for commercial purposes.

• The appliance should not be put on a carpet which can block the air ventilation on the bottom side.

RECOMMENDATIONS

• The detergent or softener in contact with air for a long time will dry and stick to your detergent drawer.To avoid this put your detergent and softener into the detergent drawer just before washing.

• It is recommended that you use pre-washing program for only very dirty clothes.

• Please do not exceed the maximum loading capacity.

• If you will not use your machine for a long time, unplug your machine, close the water supply and leave the door open in order to keep the inside of the machine dry and for prevention from unpleasant odour.

• As a result of the quality control procedures, a certain amount of water may remain in your machine. This is not harmful for your machine.

SECTION 2: INSTALLATION

You must pay attention to the following issues before using your washing machine.

REMOVAL OF TRANSPORTATION SCREWS

• Transportation screws, which are located at the back side of the machine, must be removed before running the machine.

• Loosen the screws by rotating counterclockwise by a suitable wrench. (DIAGRAM-1)

• Remove the screws by pulling them.(DIAGRAM-2)

• To the holes where the transport screws have been removed, insert

the plastic transport screw taps found in the accessories bag. (DIAGRAM-3)

• The transportation screws, that have been removed from the machine should be kept in hand for any other transportation necessities.

DIAGRAM-2 DIAGRAM-1 DIAGRAM-3

ADJUSTMENT OF FEET

• Do not install your machine on rugs or similar surfaces.

• For your machine to work silently and without any vibration, it should

be settled on a flat, non-slippery and tough ground.

• You can adjust the balance of your machine from its feet.

• First, loosen the plastic adjustment nut.

• Adjust by rotating the feet upwards or downwards.

• After the balance has been reached, tighten the plastic adjustment

nut again by rotating it upwards.

• Never put cartons, wooden blocks or similar materials under the machine to balance the irregularities on the level of the ground.

ELECTRICAL CONNECTION

• Your washing machine works with 220-240V and 50Hz.

• A special grounded plug has been attached to the network cable of

your washing machine. This plug must definitely be inserted to a grounded socket with 10 ampere. The fuse flow value of the electricity line attached to this should also be 10 ampere. If you have no such sockets and fuses in your house, let it be made by a qualified electrician.

• Our company will not be responsible for any damages that may occur as a result of usage without grounding.

• Insert the machine’s plug to a grounded socket which you can easly reach.

WATER SUPPLY CONNECTION

• Depending on the features your machine,may be with single water inlet(cold) or double water inlet (cold/hot). The white headed hose is for cold water inlet and red headed hose is for hot water inlet (valid for machines with hot&cold water inlet).

• To prevent leakage from the connection joints, 1 (valid for cold water inlet) or 2 (valid for machines with hot&cold water inlet) seals are included in the hose packing. Fit these seals at the end of water inlet hoses on the tap side.

• Connect the white headed hose to the water inlet valve with white filter and connect the red headed hose to the water inlet valve with red filter (latter is valid in machines with hot&cold water inlet). Tighten the plastic parts of the connections with your hand.Please call a qualified plumber for safer connections.

• Water pressure of 1-10 bars from your tap will enable your machine to work more efficiently.(1 bar pressure means water flow of more than 8 liters in 1 minute from a fully opened tap).

• After connections are completed, check for the non-leakage of the connection joints by turning on your tap completely.

• Be sure that water inlet hoses are not folded, broken or crushed.

• Mount the water inlet hoses to a 3”/4, geared water tap.

Cold water inlet (White filter valve)

Hot water inlet (Red filter valve)

WATER DRAIN CONNECTION

• Be sure that water inlet hoses are not folded, twisted, crushed or elongated by stretching.

• Water drain hose should be mounted at a height of minimum 60 cm, maximum 100 cm from the ground.

• The end of the water drain hose may directly be fitted to the dirty water outlet hole or a special apparatus mounted on the outlet bracket of the wash-stand.

• Never attempt to extend the water drain hose by adding extra parts.

SECTION 3: TECHNICAL SPECIFICATIONS

Maximum dry laundry capacity (kg) Recommended loading (kg)

Height (cm) 85 85 85 85 85 85 Width (cm) 59,6 59,6 59,6 59,6 59,6 59,6

Depth (cm) 37 42 51 54 57 60 Maximum spin

cycle (rpm)

32 LT 40 LT 42 LT 47 LT 52 LT 57 LT

3,5 5 5 6 7 7,5

3 4,5 4,5 5,5 6,5 7

800/

1000/1200

800/

1000/1200

600/800/

1000/1200/

1400/1600

600/800/

1000/1200/

1400/1600

600/800/

1000/1200/

1400/1600

600/800/

1000/1200/

1400/1600

1 2 3

1-Upper tray 5-Kickplate

2-Detergent drawer

3-Control panel

4-Door

These technical specifications written above for single water inlet (cold) and double water inlet (cold/hot) in machines.

SECTION 4:CONTROL PANEL

1 2 4 5

1- Detergent drawer 5- Start/pause and cancel button 2- Program knob 6- Function buttons 4- Washing operation light

START/PAUSE BUTTON

This button is used for starting a selected programme or putting a programme in progress on pause.

FUNCTION INDICATOR LAMPS

Pressing the start/hold button or any other function button switches on the lamps found above the buttons and the control panel, which indicate the wash stages of programmes. When any one of these lamps is on it means that certain programme is in use. The lamp is off when any function button or the start/hold button is pressed, or the selected function has finished its operation.

FUNCTION BUTTONS

Rinse hold

This function is recommended to be used when the clothes cannot be taken immediately after the end of the program. This will prevent occurrence of wrinkles.When this button is pressed, the last rinsing water is not drained. For the program to continue from the same point, repress the same button.

If you do not want your sensitive clothes to be spinned or you want them to be spinned sensitively, turn the program knob to O (off) position. Bring the program knob on one of the draining or spinning programs you desire and press the start/pause button. If the program you have selected is a drain program, your machine will draining the water inside.If you have selected a spinning program, your machine will perform a spinning operation and then end the program.

Extra rinse

You can have one more rinsing done in addition to the rinses which your machine has made in all washing programs by

using this function.

By using this function, you can ensure your clothes to come out less wrinkled after the washing.

Economy wash

Easy ironing

This function serves for saving energy via decreasing the temperature value and increasing the wash time of the selected wash programme by a certain level.

Your machine has also an automatical load detection system.If you load your machine with half load or less than half load, your machine can detect this lower load and change the program flow.If it happens, your “rapid wash” option lamp will be on to show you that lower load is detected.If you don’t want your program flow to be changed,then you can press “rapid wash” option button again and cancel detection.This time machine will work with normal program flow and it will not be possible to activate “rapid wash” for this cycle again.

The prewash

With this function you can start an additional wash operation for heavily soiled laundry. When you use this function you must put detergent into the prewash compartment of the detergent drawer. If the additional function features of your machine contain this option and you will wash your laundry in a prewash programme, the lamp above the function button will automatically light up. Even if you press the function button to cancel this feature it will not be cancelled at a wash function with a prewash operation.

Plus water

By using this function, you can enable your machine to take in some more water than the amount in the normal washing operation. This will decrease the friction that occurs between your clothes.This function is recommended to be used for your sensitive clothes or for the ones you desire to be rinsed really well.

+ 23 hidden pages