User Manual
Notice d'utili‐
sation
Benutzerin‐
formation
Hob
Table de
Kochfeld
cuisson
SI1M7743B
2
CONTENTS
Safety information 2
Safety instructions 4
Product description 6
Daily use 8
Hints and tips 13
Care and cleaning 15
Troubleshooting 16
Installation 18
Technical data 20
Energy efficiency 20
Subject to change without notice.
SAFETY INFORMATION
Before the installation and use of the appliance, carefully
read the supplied instructions. The manufacturer is not
responsible for any injuries or damages that are the result of
incorrect installation or usage. Always keep the instructions
in a safe and accessible location for future reference.
Children and vulnerable people safety
• This appliance can be used by children aged from 8 years
and above and persons with reduced physical, sensory or
mental capabilities or lack of experience and knowledge if
they have been given supervision or instruction concerning
the use of the appliance in a safe way and understand the
hazards involved.
• Children between 3 and 8 years of age and persons with
very extensive and complex disabilities shall be kept away
unless continuously supervised.
• Children of less than 3 years of age should be kept away
unless continuously supervised.
• Do not let children play with the appliance.
• Keep all packaging away from children and dispose of it
appropriately.
• Keep children and pets away from the appliance when it
operates or when it cools down. Accessible parts are hot.
• If the appliance has a child safety device, it should be
activated.
• Children shall not carry out cleaning and user maintenance
of the appliance without supervision.
General Safety
• WARNING: The appliance and its accessible parts
become hot during use. Care should be taken to avoid
touching heating elements.
• Do not operate the appliance by means of an external
timer or separate remote-control system.
• WARNING: Unattended cooking on a hob with fat or oil
can be dangerous and may result in fire.
• NEVER try to extinguish a fire with water, but switch off the
appliance and then cover flame e.g. with a lid or a fire
blanket.
• CAUTION: The cooking process has to be supervised. A
short term cooking process has to be supervised
continuously.
• WARNING: Danger of fire: Do not store items on the
cooking surfaces.
• Metallic objects such as knives, forks, spoons and lids
should not be placed on the hob surface since they can get
hot.
• Do not use a steam cleaner to clean the appliance.
• After use, switch off the hob element by its control and do
not rely on the pan detector.
• If the glass ceramic surface / glass surface is cracked,
switch off the appliance and unplug it from the mains. In
case the appliance is connected to the mains directly using
junction box, remove the fuse to disconnect the appliance
from power supply. In either case contact the Authorised
Service Centre.
• If the supply cord is damaged, it must be replaced by the
manufacturer, an authorized Service or similarly qualified
persons in order to avoid a hazard.
• WARNING: Use only hob guards designed by the
manufacturer of the cooking appliance or indicated by the
manufacturer of the appliance in the instructions for use as
suitable or hob guards incorporated in the appliance. The
use of inappropriate guards can cause accidents.
3
4
SAFETY INSTRUCTIONS
Installation
WARNING! Only a qualified
person must install this
appliance.
WARNING! Risk of injury or
damage to the appliance.
• Remove all the packaging.
• Do not install or use a damaged
appliance.
• Follow the installation instructions
supplied with the appliance.
• Keep the minimum distance from other
appliances and units.
• Always take care when moving the
appliance as it is heavy. Always use
safety gloves and enclosed footwear.
• Seal the cut surfaces with a sealant to
prevent moisture to cause swelling.
• Protect the bottom of the appliance
from steam and moisture.
• Do not install the appliance adjacent to
a door or under a window. This
prevents hot cookware falling from the
appliance when the door or the window
is opened.
• Each appliance has cooling fans on the
bottom.
• If the appliance is installed above a
drawer:
– Do not store any small pieces or
sheets of paper that could be pulled
in, as they can damage the cooling
fans or impair the cooling system.
– Keep a distance of minimum 2 cm
between the bottom of the
appliance and parts stored in the
drawer.
Electrical Connection
WARNING! Risk of fire and
electric shock.
• All electrical connections should be
made by a qualified electrician.
• The appliance must be earthed.
• Before carrying out any operation make
sure that the appliance is disconnected
from the power supply.
• Make sure that the parameters on the
rating plate are compatible with the
electrical ratings of the mains power
supply.
• Make sure the appliance is installed
correctly. Loose and incorrect electricity
mains cable or plug (if applicable) can
make the terminal become too hot.
• Use the correct electricity mains cable.
• Do not let the electricity mains cable
tangle.
• Make sure that a shock protection is
installed.
• Use the strain relief clamp on the cable.
• Make sure the mains cable or plug (if
applicable) does not touch the hot
appliance or hot cookware, when you
connect the appliance to the near
sockets.
• Do not use multi-plug adapters and
extension cables.
• Make sure not to cause damage to the
mains plug (if applicable) or to the
mains cable. Contact our Authorised
Service Centre or an electrician to
change a damaged mains cable.
• The shock protection of live and
insulated parts must be fastened in
such a way that it cannot be removed
without tools.
• Connect the mains plug to the mains
socket only at the end of the
installation. Make sure that there is
access to the mains plug after the
installation.
• If the mains socket is loose, do not
connect the mains plug.
• Do not pull the mains cable to
disconnect the appliance. Always pull
the mains plug.
• Use only correct isolation devices: line
protecting cut-outs, fuses (screw type
fuses removed from the holder), earth
leakage trips and contactors.
• The electrical installation must have an
isolation device which lets you
5
disconnect the appliance from the
mains at all poles. The isolation device
must have a contact opening width of
minimum 3 mm.
Use
WARNING! Risk of injury,
burns and electric shock.
• Remove all the packaging, labelling
and protective film (if applicable) before
first use.
• Use this appliance in a household
environment.
• Do not change the specification of this
appliance.
• Make sure that the ventilation openings
are not blocked.
• Do not let the appliance stay
unattended during operation.
• Set the cooking zone to “off” after each
use.
• Do not rely on the pan detector.
• Do not put cutlery or saucepan lids on
the cooking zones. They can become
hot.
• Do not operate the appliance with wet
hands or when it has contact with
water.
• Do not use the appliance as a work
surface or as a storage surface.
• If the surface of the appliance is
cracked, disconnect immediately the
appliance from the power supply. This
to prevent an electrical shock.
• Users with a pacemaker must keep a
distance of minimum 30 cm from the
induction cooking zones when the
appliance is in operation.
• When you place food into hot oil, it may
splash.
WARNING! Risk of fire and
explosion
• Fats and oil when heated can release
flammable vapours. Keep flames or
heated objects away from fats and oils
when you cook with them.
• The vapours that very hot oil releases
can cause spontaneous combustion.
• Used oil, that can contain food
remnants, can cause fire at a lower
temperature than oil used for the first
time.
• Do not put flammable products or items
that are wet with flammable products
in, near or on the appliance.
WARNING! Risk of damage to
the appliance.
• Do not keep hot cookware on the
control panel.
• Do not put a hot pan cover on the glass
surface of the hob.
• Do not let cookware to boil dry.
• Be careful not to let objects or
cookware fall on the appliance. The
surface can be damaged.
• Do not activate the cooking zones with
empty cookware or without cookware.
• Do not put aluminium foil on the
appliance.
• Cookware made of cast iron, aluminium
or with a damaged bottom can cause
scratches on the glass / glass ceramic.
Always lift these objects up when you
have to move them on the cooking
surface.
• This appliance is for cooking purposes
only. It must not be used for other
purposes, for example room heating.
Care and cleaning
• Clean the appliance regularly to
prevent the deterioration of the surface
material.
• Deactivate the appliance and let it cool
down before you clean it.
• Disconnect the appliance from the
electrical supply before maintenance.
• Do not use water spray and steam to
clean the appliance.
• Clean the appliance with a moist soft
cloth. Only use neutral detergents. Do
not use any abrasive products,
abrasive cleaning pads, solvents or
metal objects.
1
1
1
1
2
1 2 3
6
7 85
10 9
11
4
6
Service
• To repair the appliance contact an
Authorised Service Centre.
• Use original spare parts only.
Disposal
WARNING! Risk of injury or
suffocation.
PRODUCT DESCRIPTION
Cooking surface layout
• Contact your municipal authority for
information on how to discard the
appliance correctly.
• Disconnect the appliance from the
mains supply.
• Cut off the mains electrical cable close
to the appliance and dispose of it.
Induction cooking zone
1
Control panel
2
Control panel layout
Use the sensor fields to operate the appliance. The displays, indicators and sounds tell
which functions operate.
1
Sensor
field
Function Comment
ON / OFF To activate and deactivate the hob.
7
10
11
Sensor
field
2
3
4
- Heat setting display To show the heat setting.
5
- Timer indicators of
6
- Timer display To show the time in minutes.
7
8
9
/
- Control bar To set a heat setting.
Function Comment
Lock / Child Safety De‐
vice
Pause To activate and deactivate the function.
MultiZone To activate and deactivate the function.
cooking zones
Auto-Vent To activate and deactivate the manual mode
- To select the cooking zone.
- To increase or decrease the time.
Heat setting displays
Display Description
The cooking zone is deactivated.
-
The cooking zone operates.
Pause operates.
To lock / unlock the control panel.
To show for which zone you set the time.
of the function.
+ digit
/ /
Accelerator operates.
Power function operates.
There is a malfunction.
Eco-Heat (3-step Residual heat indicator): continue cooking / keep
warm / residual heat.
Lock / Child Safety Device operates.
Incorrect or too small cookware or no cookware on the cooking zone.
Automatic Switch Off operates.
8
Eco-Heat (3 step Residual heat indicator)
WARNING! / / There
is a risk of burns from residual
heat. The indicator shows the
level of the residual heat. If a
given zone becomes too hot
the function may lower the heat
setting for neighbouring zones.
DAILY USE
WARNING! Refer to Safety
chapters.
Activating and deactivating
Touch for 1 second to activate or
deactivate the hob.
Automatic Switch Off
The function deactivates the hob
automatically if:
• all cooking zones are deactivated,
• you do not set the heat setting after you
activate the hob,
• you spill something or put something
on the control panel for more than 10
seconds (a pan, a cloth, etc.). An
acoustic signal sounds and the hob
deactivates. Remove the object or
clean the control panel.
• the hob gets too hot (e.g. when a
saucepan boils dry). Let the cooking
zone cool down before you use the hob
again.
• you use incorrect cookware. The
symbol comes on and the cooking
zone deactivates automatically after 2
minutes.
• you do not deactivate a cooking zone
or change the heat setting. After some
time comes on and the hob
deactivates.
The relation between the heat setting
and the time after which the hob
deactivates:
The induction cooking zones produce the
heat necessary for the cooking process
directly in the bottom of the cookware. The
glass ceramic is heated by the heat of the
cookware.
Heat setting The hob deacti‐
vates after
, 1 - 3
4 - 7 5 hours
8 - 9 4 hours
10 - 14 1.5 hour
6 hours
The heat setting
To set or change the heat setting:
Touch the control bar at the correct heat
setting or move your finger along the
control bar until you reach the correct heat
setting.
Using the cooking zones
Place the cookware in the centre of the
selected zone. Induction cooking zones
adapt to the dimension of the bottom of
the cookware automatically.
You can cook with large cookware placed
on two cooking zones at the same time.
The cookware must cover the centres of
both zones. Correct cookware positions:
Incorrect cookware positions:
MultiZone
The function operates when the
pot covers the centres of the
two zones.
This function connects two left side
cooking zones and they operate as one.
First set the heat setting for one of the left
side cooking zones.
To activate the function: touch
or change the heat setting touch one of
the control sensors.
To deactivate the function: touch
cooking zones operate independently.
. To set
. The
Accelerator
Activate this function to get a desired heat
setting in a shorter time. When it is on, the
zone operates on the highest setting in the
beginning and then continues to cook at
the desired heating setting.
To activate the function the
cooking zone must be cold.
To activate the function for a cooking
zone: touch the end of the control bar on
the right ( comes on). Immediately
touch a desired heat setting. After 3
seconds comes on.
To deactivate the function: change the
heat setting.
Power function
This function makes more power available
to the induction cooking zones. The
function can be activated for the induction
cooking zone only for a limited period of
time. After this time the induction cooking
zone automatically sets back to the
highest heat setting.
Refer to “Technical information”
chapter.
To activate the function for a cooking
zone: touch the end of the control bar on
the right. comes on.
To deactivate the function: change the
heat setting.
Timer
Count Down Timer
You can use this function to set how long
the cooking zone should operate for a
single cooking session.
First set the heat setting for the cooking
zone then set the function.
To set the cooking zone: touch
again and again until the indicator of a
necessary cooking zone comes on.
To activate the function: touch of the
timer to set the time (00 - 99 minutes).
When the indicator of the cooking zone
starts to flash slowly the time counts
down.
To see the remaining time: set the
cooking zone with
the cooking zone starts to flash quickly.
The display shows the remaining time.
To change the time: set the cooking zone
with . Touch or .
To deactivate the function: set the
cooking zone with
. The indicator of
and touch .
9
10
The remaining time counts back to 00.
The indicator of the cooking zone goes
out.
When the time comes to an
end, the sound operates and
00 flashes. The cooking zone
deactivates.
To stop the sound: touch .
CountUp Timer (The count up timer)
You can use this function to monitor how
long the cooking zone operates.
To set the cooking zone: touch
again and again until the indicator of a
necessary cooking zone comes on.
To activate the function: touch of the
timer. comes on. When the indicator of
the cooking zone starts to flash slowly the
time counts up. The display switches
between and counted time (minutes).
To see how long the cooking zone
operates: set the cooking zone with
. The indicator of the cooking zone
starts to flash quickly. The display shows
how long the zone operates.
To deactivate the function: set the
cooking zone with
. The indicator of the cooking zone goes
out.
Minute Minder
You can use this function as a Minute
Minder when the hob is activated and the
cooking zones do not operate. The heat
setting display shows .
To activate the function: touch
Touch or of the timer to set the time.
When the time comes to an end, the
sound operates and 00 flashes.
To stop the sound: touch .
The function has no effect on
the operation of the cooking
zones.
and touch or
.
Pause
This function sets all cooking zones that
operate to the lowest heat setting.
When the function operates, all other
symbols on the control panels are locked.
The function does not stop the timer
functions.
Touch
comes on. The heat setting is lowered
to 1.
To deactivate the function, touch .
The previous heat setting comes on.
to activate the function.
Lock
You can lock the control panel while
cooking zones operate. It prevents an
accidental change of the heat setting.
Set the heat setting first.
To activate the function: touch .
comes on for 4 seconds. The Timer stays
on.
To deactivate the function: touch .
The previous heat setting comes on.
When you deactivate the hob,
you also deactivate this
function.
Child Safety Device
This function prevents an accidental
operation of the hob.
To activate the function: activate the hob
with . Do not set the heat setting. Touch
for 4 seconds. comes on.
Deactivate the hob with
To deactivate the function: activate the
hob with . Do not set the heat setting.
Touch for 4 seconds. comes on.
Deactivate the hob with .
To override the function for only one
cooking time: activate the hob with
comes on. Touch for 4 seconds.
Set the heat setting in 10 seconds. You
.
.
11
can operate the hob. When you deactivate
the hob with the function operates
again.
OffSound Control (Deactivating and activating the sounds)
Deactivate the hob. Touch for 3
seconds. The display comes on and goes
out. Touch for 3 seconds. or
comes on. Touch of the timer to
choose one of the following:
• - the sounds are off
• - the sounds are on
To confirm your selection wait until the
hob deactivates automatically.
When the function is set to you can
hear the sounds only when:
• you touch
• Minute Minder comes down
• Count Down Timer comes down
• you put something on the control panel.
Power limitation
Originally the hob is at its highest possible
power level.
To decrease or increase the power
level:
1. Deactivate the hob.
2. Touch
comes on and goes off.
3. Touch for 3 seconds. or
comes on.
4. Touch . P0 comes on.
5. Touch / of the Timer to set the
power level.
Power levels
Refer to “Technical information” chapter.
• P 72 — 7200 W
• P 15 — 1500 W
• P 20 — 2000 W
• P 25 — 2500 W
• P 30 — 3000 W
• P 35 — 3500 W
• P 40 — 4000 W
• P 45 — 4500 W
for 3 seconds. The display
• P 50 — 5000 W
• P 60 — 6000 W
CAUTION! Make sure that the
selected power fits to the
house installation fuses.
Eco-Logic
• Cooking zones are grouped according
to the location and number of the
phases in the hob. See the illustration.
• Each phase has a maximum electricity
loading of 3600 W.
• The function divides the power
between cooking zones connected to
the same phase.
• The function activates when the total
electricity loading of the cooking zones
connected to a single phase exceeds
3600 W.
• The function decreases the power to
the other cooking zones connected to
the same phase.
• The heat setting display of the reduced
zones changes between two levels.
When you set the Power limitation
function to 6.0 kW or less, power of the
hob is divided between all cooking zones.
When you set the Power limitation
function to more than 6.0 kW, power of
the hob is divided between two cooking
zones in a pair.
12
Auto-Vent
It is an advanced automatic function which
connects the hob to a special hood. Both
the hob and the hood have an infrared
signal communicator. Speed of the fan is
defined automatically on basis of mode
setting and temperature of the hottest
cookware on the hob. You can also
operate the fan from the hob manually.
For most of the hoods the
remote system is originally
deactivated. Activate it before
you use the function. For more
information refer to hood user
manual.
Operating the function automatically
To operate the function automatically set
the automatic mode to H1 – H6. The hob
is originally set to H5. The hood reacts
whenever you operate the hob. The hob
recognizes temperature of the cookware
automatically and adjusts the speed of the
fan.
Automatic modes
Auto‐
matic
light
Mode
H0
Mode
H1
Off Off Off
On Off Off
Boil‐
ing
Fry‐
1)
ing
2)
Auto‐
matic
light
Mode
3)
H2
Mode
H3
Mode
H4
Mode
H5
Mode
H6
1)
The hob detects the boiling process and activates
fan speed in accordance with automatic mode.
2)
The hob detects the frying process and activates
fan speed in accordance with automatic mode.
3)
This mode activates the fan and the light and does
not rely on the temperature.
On Fan
On Off Fan
On Fan
On Fan
On Fan
Boil‐
1)
ing
speed
1
speed
1
speed
1
speed
2
Fry‐
2)
ing
Fan
speed
1
speed
1
Fan
speed
1
Fan
speed
2
Fan
speed
3
Changing the automatic mode
1. Deactivate the appliance.
2. Touch for 3 seconds. The display
comes on and goes off.
3. Touch for 3 seconds.
4. Touch
a few times until
comes on.
5. Touch of the Timer to select an
automatic mode.
To operate the hood directly on
the hood panel deactivate the
automatic mode of the function.
13
When you finish cooking and
deactivate the hob, the hood
fan may still operate for a
certain period of time. After that
time the system deactivates the
fan automatically and prevents
you from accidental activation
of the fan for the next 30
seconds.
Operating the fan speed manually
You can also operate the function
manually. To do that touch when the
hob is active. This deactivates automatic
operation of the function and allows you to
change the fan speed manually. When
you press you raise the fan speed by
one. When you reach an intensive level
HINTS AND TIPS
WARNING! Refer to Safety
chapters.
Cookware
For induction cooking zones a
strong electro-magnetic field
creates the heat in the
cookware very quickly.
Use the induction cooking
zones with suitable cookware.
Cookware material
• correct: cast iron, steel, enamelled
steel, stainless steel, multi-layer bottom
(with a correct marking from a
manufacturer).
• not correct: aluminium, copper, brass,
glass, ceramic, porcelain.
Cookware is suitable for an induction
hob if:
• water boils very quickly on a zone set
to the highest heat setting.
• a magnet pulls on to the bottom of the
cookware.
and press again you will set fan speed
to 0 which deactivates the hood fan. To
start the fan again with fan speed 1 touch
.
To activate automatic operation
of the function, deactivate the
hob and activate it again.
Activating the light
You can set the hob to activate the light
automatically whenever you activate the
hob. To do so set the automatic mode to
H1 – H6.
The light on the hood
deactivates 2 minutes after
deactivating the hob.
The bottom of the cookware
must be as thick and flat as
possible.
Ensure pan bases are clean
and dry before placing on the
hob surface.
Cookware dimensions
Induction cooking zones adapt to the
dimension of the bottom of the cookware
automatically.
The cooking zone efficiency is related to
the diameter of the cookware. The
cookware with a diameter smaller than the
minimum receives only a part of the power
generated by the cooking zone.
Refer to "Technical data".
The noises during operation
If you can hear:
• crack noise: cookware is made of
different materials (sandwich
construction).
• whistle sound: you use the cooking
zone with high power level and the
14
cookware is made of different materials
(sandwich construction).
• humming: you use high power level.
• clicking: electric switching occurs.
• hissing, buzzing: the fan operates.
The noises are normal and do not refer
to hob malfunction.
Eco-Off (Eco Timer)
To save energy, the heater of the cooking
zone deactivates before the count down
timer sounds. The difference in the
operation time depends on the heat
Examples of cooking applications
The correlation between the heat setting
of a zone and its consumption of power is
not linear. When you increase the heat
setting, it is not proportional to the
increase of the consumption of power. It
means that a cooking zone with the
medium heat setting uses less than a half
of its power.
The data in the table is for
guidance only.
setting level and the length of the cooking
operation.
Heat setting Use to: Time
(min)
- 1
1 - 3 Hollandaise sauce, melt: but‐
1 - 3 Solidify: fluffy omelettes, baked
3 - 5 Simmer rice and milkbased
5 - 7 Steam vegetables, fish, meat. 20 -
7 - 9 Steam potatoes. 20 -
7 - 9 Cook larger quantities of food,
9 - 12 Gentle fry: escalope, veal cor‐
12 - 13 Heavy fry, hash browns, loin
14 Boil water, cook pasta, sear meat (goulash, pot roast), deep-fry chips.
Keep cooked food warm. as
nec‐
essary
5 - 25 Mix from time to time.
ter, chocolate, gelatine.
10 -
eggs.
dishes, heat up ready-cooked
meals.
stews and soups.
don bleu, cutlets, rissoles,
sausages, liver, roux, eggs,
pancakes, doughnuts.
steaks, steaks.
Boil large quantities of water. Power function is activated.
40
25 50
45
60
60 150
as
nec‐
essary
5 - 15 Turn halfway through.
Hints
Put a lid on the cookware.
Cook with a lid on.
Add at least twice as much liq‐
uid as rice, mix milk dishes
halfway through the proce‐
dure.
Add a couple of tablespoons
of liquid.
Use max. ¼ l of water for 750
g of potatoes.
Up to 3 l of liquid plus ingredi‐
ents.
Turn halfway through.
15
Hints and Tips for Auto-Vent
When you operate the hob with the
function:
• Protect the hood panel from direct
sunlight.
• Do not spot halogen light on the hood
panel.
• Do not cover the hob control panel.
• Do not interrupt the signal between the
hob and the hood (for example with a
hand or a cookware handle). See the
picture.
The hood in the picture is only
exemplary.
Other remotely controlled
appliances may block the
signal. Do not use any remotely
controlled appliances at the
time when you use the function
on the hob.
Cooker hoods with the Auto-Vent
function
To find the full range of cooker hoods
which work with this function refer to our
consumer website.
CARE AND CLEANING
WARNING! Refer to Safety
chapters.
General information
• Clean the hob after each use.
• Always use cookware with a clean
base.
• Scratches or dark stains on the surface
have no effect on how the hob
operates.
• Use a special cleaner suitable for the
surface of the hob.
• Use a special scraper for the glass.
Cleaning the hob
• Remove immediately: melted plastic,
plastic foil, sugar and food with sugar. If
not, the dirt can cause damage to the
hob. Take care to avoid burns. Put the
special scraper on the glass surface at
an acute angle and move the blade on
the surface.
• Remove when the hob is sufficiently
cool: limescale rings, water rings, fat
stains, shiny metallic discoloration.
Clean the hob with a moist cloth and
non-abrasive detergent. After cleaning,
wipe the hob dry with a soft cloth.
• Remove shiny metallic
discoloration: use a solution of water
with vinegar and clean the glass
surface with a moist cloth.
16
TROUBLESHOOTING
WARNING! Refer to Safety
chapters.
What to do if...
Problem Possible cause Remedy
You cannot activate or oper‐
ate the hob.
The fuse is blown. Make sure that the fuse is
You do not set the heat set‐
You touched 2 or more sen‐
Pause function operates. Refer to "Daily use".
There is water or fat stains
An acoustic signal sounds
and the hob deactivates.
An acoustic signal sounds
when the hob is deactivated.
The hob deactivates. You put something on the
Residual heat indicator does
not come on.
Auto-Vent does not work. You covered the control
Accelerator does not oper‐
ate.
The highest heat setting is
The hob is not connected to
an electrical supply or it is
connected incorrectly.
ting for 10 seconds.
sor fields at the same time.
on the control panel.
You put something on one
or more sensor fields.
sensor field .
The zone is not hot because
it operated only for a short
time or the sensor is dam‐
aged.
panel.
The zone is hot. Let the zone become suffi‐
set.
Check if the hob is correctly
connected to the electrical
supply. Refer to the connec‐
tion diagram.
the cause of the malfunc‐
tion. If the fuse is blown
again and again, contact a
qualified electrician.
Activate the hob again and
set the heat setting in less
than 10 seconds.
Touch only one sensor field.
Clean the control panel.
Remove the object from the
sensor fields.
Remove the object from the
sensor field.
If the zone operated suffi‐
ciently long to be hot, speak
to an Authorised Service
Centre.
Remove the object from the
control panel.
ciently cool.
The highest heat setting has
the same power as the func‐
tion.
Problem Possible cause Remedy
The heat setting changes
between two levels.
The sensor fields become
hot.
There is no sound when you
touch the panel sensor
fields.
comes on.
comes on.
comes on.
The cookware is unsuitable. Use suitable cookware. Re‐
The diameter of the bottom
and a number come on.
You can hear a constant
beep noise.
Power management oper‐
ates.
The cookware is too large or
you put it too near to the
controls.
The sounds are deactivated. Activate the sounds. Refer
Automatic Switch Off oper‐
ates.
Child Safety Device or Lock
operates.
There is no cookware on the
zone.
of the cookware is too small
for the zone.
There is an error in the hob. Deactivate the hob and acti‐
The electrical connection is
incorrect.
Refer to "Daily use".
Put large cookware on the
rear zones if possible.
to "Daily use".
Deactivate the hob and acti‐
vate it again.
Refer to "Daily use".
Put cookware on the zone.
fer to "Hints and tips".
Use cookware with correct
dimensions. Refer to "Tech‐
nical data".
vate it again after 30 sec‐
onds. If comes on again,
disconnect the hob from the
electrical supply. After 30
seconds, connect the hob
again. If the problem contin‐
ues, speak to an Authorised
Service Centre.
Disconnect the hob from the
electrical supply. Ask a
qualified electrician to check
the installation.
17
If you cannot find a solution...
If you cannot find a solution to the problem
yourself, contact your dealer or an
Authorised Service Centre. Give the data
from the rating plate. Give also three digit
letter code for the glass ceramic (it is in
the corner of the glass surface) and an
error message that comes on. Make sure,
you operated the hob correctly. If not the
servicing by a service technician or dealer
will not be free of charge, also during the
warranty period. The instructions about
the Service Centre and conditions of
guarantee are in the guarantee booklet.
N
L1
N
L
230V~ 400V 2~N
L2
18
INSTALLATION
WARNING! Refer to Safety
chapters.
Before the installation
Before you install the hob, write down the
information bellow from the rating plate.
The rating plate is on the bottom of the
hob.
Serial number ...........................
Built-in hobs
Only use the built-in hobs after you
assemble the hob into correct built-in units
and work surfaces that align to the
standards.
Connection cable
• The hob is supplied with the connection
cable.
• Replace the damaged mains cable only
with the spare parts cable. Speak to
your local Authorised Service Center.
WARNING! All electrical
connections must be made by
a qualified electrician.
CAUTION! Do not drill or
solder the wire ends. This is
strictly forbidden!
CAUTION! Do not connect the
cable without cable end sleeve.
Two-phase connection
1. Remove the cable end sleeve from
black and brown wires.
2. Remove an insulation of the brown
and black cable ends.
3. Apply a new wire end sleeve of 1.5
mm² on each cable end. (special tool
required).
Cable cross section
One-phase connection - 230 V~ Two-phase connection - 400 V 2 ~ N
Green - yellow Green - yellow
N Blue and blue Blue and blue N
L Black and brown Black L1
Brown L2
Assembly
min.
50mm
min.
500mm
R 5mm
min.
55mm
560+1mm
490+1mm
min.
28 mm
min.
12 mm
min. 60mm
19
If the appliance is installed
above a drawer, the hob
ventilation can warm up the
items stored in the drawer
during the cooking process.
20
TECHNICAL DATA
Rating plate
Model SI1M7743B PNC 949 594 450 00
Typ 61 B4A 01 AD 220 - 240 V / 400 V 2N 50 - 60 Hz
Induction 7.2 kW Made in Germany
Ser.Nr. ................. 7.2 kW
SMEG
Cooking zones specification
Cooking zone Nominal pow‐
er (maximum
heat setting)
[W]
Left front 2300 3200 10 125 - 210
Left rear 2300 3200 10 125 - 210
Right front 1400 2500 4 125 - 145
Right rear 1800 2800 10 145 - 180
The power of the cooking zones can be
different in some small range from the
Power func‐
tion [W]
For optimal cooking results use cookware
no larger than the diameter in the table.
Power func‐
tion maximum
duration [min]
Cookware di‐
ameter [mm]
data in the table. It changes with the
material and dimensions of the cookware.
ENERGY EFFICIENCY
Product information according to EU 66/2014
Model identification SI1M7743B
Type of hob Built-In Hob
Number of cooking zones 4
Heating technology Induction
Diameter of circular cook‐
ing zones (Ø)
Energy consumption per
cooking zone (EC electric
cooking)
Energy consumption of the
hob (EC electric hob)
Left front
Left rear
Right front
Right rear
Left front
Left rear
Right front
Right rear
181.2 Wh / kg
21.0 cm
21.0 cm
14.5 cm
18.0 cm
178.4 Wh / kg
178.4 Wh / kg
183.2 Wh / kg
184.9 Wh / kg
21
EN 60350-2 - Household electric cooking
appliances - Part 2: Hobs - Methods for
measuring performance
The energy measurements referring to the
cooking area are identified by the
markings of the respective cooking zones.
Energy saving
You can save energy during everyday
cooking if you follow below hints.
• When you heat up water, use only the
amount you need.
• If it is possible, always put the lids on
• Before you activate the cooking zone
• Put the smaller cookware on the
• Put the cookware directly in the centre
• Use the residual heat to keep the food
ENVIRONMENTAL CONCERNS
Recycle materials with the symbol . Put
the packaging in relevant containers to
recycle it. Help protect the environment
and human health by recycling waste of
electrical and electronic appliances. Do
not dispose of appliances marked with the
symbol with the household waste.
Return the product to your local recycling
facility or contact your municipal office.
the cookware.
put the cookware on it.
smaller cooking zones.
of the cooking zone.
warm or to melt it.
867346360-B-082018
Loading...