Smeg PGF75-2, PGF75F, PGF75BE-2 User Manual
Summary
1 INSTRUCTIONS FOR SAFE AND PROPER USE_______________ 20
2 POSITIONING OF THE HOB_______________________________ 22
3 ADJUSTMENT TO DIFFERENT TYPES OF GAS_______________ 29
4 FINAL OPERATIONS_____________________________________ 31
5 USING THE HOB________________________________________ 32
6 CLEANING AND MAINTENANCE ___________________________ 34
THESE INSTRUCTIONS ARE VALID ONLY FOR END USER COUNTRIES WHOSE
IDENTIFICATION SYMBOLS APPEAR ON THE COVER OF THIS MANUAL.
INSTRUCTIONS FOR THE INSTALLER: these are for the qualified
technician who must carry out a suitable check of the gas system,
install the appliance, set it functioning and carry out an inspection test.
INSTRUCTIONS FOR THE USER : these contain user advice,
description of the commands and the correct procedures for cleaning
and maintenance of the appliance.
19
Introduction
1 INSTRUCTIONS FOR SAFE AND PROPER USE
THIS MANUAL IS AN INTEGRAL PART OF THE APPLIANCE AND
THEREFORE MUST BE KEPT IN ITS ENTIRETY AND IN AN ACCESSIBLE
PLACE FOR THE WHOLE WORKING LIFE OF THE HOB. WE ADVISE
READING THIS MANUAL AND ALL THE INSTRUCTIONS THEREIN BEFORE
USING THE HOB. ALSO KEEP THE SERIES OF NOZZLES SUPPLIED.
INSTALLATION MUST BE CARRIED OUT BY QUALIFIED PERSONNEL IN
ACCORDANCE WITH THE REGULATIONS IN FORCE. THIS APPLIANCE IS
INTENDED FOR FOR DOMESTIC USES AND CONFORMS TO EEC
DIRECTIVES CURRENTLY IN FORCE. THE APPLIANCE IS DESIGNED TO
CARRY OUT THE FOLLOWING FUNCTIONS: COOKING AND HEATING
FOOD; ALL OTHER USES ARE TO BE CONSIDERED IMPROPER.
THE MANUFACTURER DECLINES ALL LIABILITY FOR IMPROPER USE .
DO NOT LEAVE THE PACKAGING MATERIALS UNATTENDED IN THE HOME
ENVIRONMENT. SEPARATE THE DIFFERENT WASTE MATERIALS FROM
THE PACKAGING AND DELIVER THEM TO THE NEAREST COLLECTION
CENTRE FOR RECYCLABLE WASTE.
REGULATIONS REQUIRE THAT THE APPLIANCE IS EARTHED IN
ACCORDANCE WITH ELECTRICAL SAFETY REGULATIONS.
THE PLUG TO BE CONNECTED TO THE POWER SUPPLY CABLE AND THE
SOCKET MUST BE OF THE SAME TYPE AND MUST CONFORM TO
CURRENT REGULATIONS.
THE POWER SOCKET MUST BE ACCESSIBLE AFTER THE APPLIANCE HAS
BEEN BUILT IN.
NEVER UNPLUG THE APPLIANCE BY PULLING THE POWER SUPPLY
CABLE.
IMMEDIATELY AFTER INSTALLATION, CARRY OUT A BRIEF INSPECTION
TEST OF THE APPLIANCE, FOLLOWING THE INSTRUCTIONS BELOW.
SHOULD THE APPLIANCE NOT FUNCTION, DISCONNECT IT FROM THE
POWER SUPPLY AND CONTACT YOUR NEAREST TECHNICAL ASSISTANCE
CENTRE.
NEVER ATTEMPT TO REPAIR THE APPLIANCE YOURSELF.
ALWAYS CHECK THAT THE CONTROL KNOBS ARE IN THE POSITION
(OFF) WHEN YOU FINISH USING THE HOB.
20
Introduction
THE APPLIANCE DATA PLATE, WITH TECHNICAL DATA, REGISTRATION
NUMBER AND BRAND NAME, IS POSITIONED AT A VISIBLE POINT UNDER
THE SAFETY COVER.
THE DATA PLATE ON THE PROTECTIVE COVER MUST NEVER BE
REMOVED.
DO NOT PUT PANS WITHOUT PERFECTLY PERFECTLY SMOOTH AND FLAT
BOTTOMS ON THE HOB PANSTAND GRIDS.
DO NOT USE COOKING RECEPTACLES THAT EXTEND BEYOND THE
OUTSIDE PERIMETER OF THE HOB.
THE APPLIANCE IS DESIGNED FOR USE BY ADULTS. DO NOT ALLOW
CHILDREN TO GO NEAR OR PLAY WITH IT.
THIS APPLIANCE IS MARKED ACCORDING TO THE EUROPEAN DIRECTIVE
2002/96/EC ON WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT
(WEEE).
THIS GUIDELINE IS THE FRAME OF A EUROPEAN-WIDE VALIDITY OF
RETURN AND RECYCLING ON WASTE ELECTRICAL AND ELECTRONIC
EQUIPMENT.
The manufacturer declines all liability for injury to persons or animals
and for damage to property resulting from non-observance of the above
prescriptions or from tampering with any part of the appliance or for the
use of non-original spare parts.
21
n
Instructions for the installer
2 POSITIONING OF THE HOB
The following operation requires building and/or carpentry work so must
be carried out by a competent tradesman.
Installation can be carried out on various materials such as masonry,
metal, solid wood or plastic laminated wood, as long as they are heatresistant (T 90°C).
2.1 Attachment to support structure, traditional built-i
model (fig. 1)
Create an opening with the
dimensions shown in the
figure in the work surface,
observing a minimum
distance of 50 mm from the
rear edge.
This appliance can be
installed next to walls that are
higher than the work surface,
as long as the distance "X" is
kept between the appliance
and the wall, as shown in the
figure, to avoid damage from overheating. Make sure there is a minimum
of 750 mm between the gas rings and any shelf that may be installed
directly above them.
Carefully position the gasket provided all around the outer edge of the
hole in the work surface as shown in figure 2, pressing it down lightly to
ensure it adheres properly. The front and rear sides of the gasket must
skim the hole. Having done this, place the hob on top of the gasket and
using the screws and fixing brackets “C” or “D” (depending on the depth
of the worktop – Fig.4) secure the hob to the support structure, ensuring
it is level. The brackets “C” secure the hob to a structure having a depth
of 20 to 30 mm. The brackets “D” on the other hand, are for use with
worktops having a depth of 30 to 50 mm.
Carefully trim any excess from edge “A” (Fig.3) of the gasket. The
distances in figure 2 refer to the hole on the inner side of the gasket.
1)
2)
22
3)
Instructions for the installer
4)
2.2 Attachment to support structure, flush-mounting model
Create an opening with the dimensions
shown in the figure in the work surface,
observing a minimum distance of 50 mm
from the rear edge.
The lower part of the protective cover
must be fully accessible when the
appliance is installed. This appliance can
be installed next to walls that are higher
than the work surface, as long as the
distance "X" is kept, as shown in the
figure, to avoid damage from overheating.
Make sure there is a minimum of 750 mm (Fig. 1) between the gas rings and any shelf
that may be installed directly above them.
This type of appliance also requires a cut 3 mm deep in the work-top with the
dimensions shown in figure 4 (detail A, figure 2). Before positioning the hob, position
the adhesive sponge material “E” supplied over the milled surface (fig. 2-3). Having
done this, place the hob on the milled surface and using the screws and fixing brackets
“C” or “D” (depending on the depth of the worktop) secure the hob to the support
structure, ensuring it is level. The brackets “C” secure the hob to a structure having a
depth of 20 to 30 mm. The brackets “D” on the other hand, are for use with worktops
having a depth of 30 to 50 mm.
1)
23
Loading...