Smeg LS1011X, LVS450N, DWF410WH, LVS450B, DWF410SS Instruction Manual

...

INSTRUCTION MANUAL

DISHWASHER

Contents

1. Safety and operating instructions __________________________ 34

2. Installation and hook-up _________________________________ 37

3. Description of the controls _______________________________ 39

4. Operating instructions __________________________________ 46

5. Cleaning and maintenance_______________________________ 57

6. Troubleshooting _______________________________________ 61

Thank you for choosing this product. We advise you to carefully read all the instructions contained in this manual, in order to understand how to operate your dishwasher safely and correctly. The manual is divided into paragraphs, which provide a step by step description of the dishwasher functions, with clear instructions accompanied by detailed illustrations. Recommendations are given for the correct use of the baskets, spray arms, containers, filters, washing programs, and for operating the controls. Follow the recommended cleaning procedures to ensure that your dishwasher always remains in perfect working order. This manual provides a quick and easy reference for answering all your questions concerning the use of your new dishwasher.

INSTALLATION INSTRUCTIONS: these are intended for the qualified technician who must carry out the installation, hook-up and testing of the appliance.

USER INSTRUCTIONS: these consist of recommendations for using the appliance, a description of its controls and of the correct cleaning and maintenance procedures.

Safety instructions

1. Safety and operating instructions

THIS MANUAL FORMS AN INTEGRAL PART OF THE APPLIANCE: IT MUST ALWAYS BE KEPT INTACT TOGETHER WITH THE DISHWASHER. BEFORE USING THE APPLIANCE, CAREFULLY READ ALL THE INSTRUCTIONS CONTA INED IN THIS MA NUAL. INSTALLATION MUST BE PERFORMED BY A QUALIFIED TECHNICIAN, IN COMPLIANCE WITH THE REGULATIONS IN FORCE. THIS APPLIANCE IS INTENDED FOR DOMESTIC USE, AND COMPLIES WITH THE

DIRECTIVES 72/23, 897336 (INCLUDING 92/31)

INCLUDING THE PREVENTION AND ELIMINATION OF RADIO FREQUENCY INTERFERENCE. THE APPLIANCE IS DESIGNED FOR THE FOLLOWING PURPOSE:

AND DRYING OF DISHES

IMPROPER.

USES OTHER THAN THOSE DESCRIBED ABOVE.

THE NAME PLATE FEATURING THE TECHNICAL DATA, SERIAL NUMBER AND MARKINGS IS VISIBLY POSITIONED ON THE INNER EDGE OF THE DOOR.

NEVER BE REMOVED.

DO NOT LEAVE THE DISCARDED PACKAGING MATERIALS UNSUPERVISED WITHIN THE HOME. SEPARATE THE VARIOUS MATERIALS WHICH MAKE UP THE PACKAGING AND TAKE THEM TO THE NEAREST SORTED WASTE COLLECTION CENTRE.

THE MANUFACTURER DECLINES ALL RESPONSIBILITY FOR

THE NAME PLATE ON THE INNER EDGE OF THE DOOR MUST

; ANY OTHER USE SHALL BE CONSIDERED

CURREN TL Y IN F ORC E,

EEC

WASHING

THE APPLIANCE MUST BE PROVIDED WITH AN EARTH CONNECTION IN ACCORDANCE WITH THE ELECTRICAL SAFETY REGULATIONS IN FORCE.

THE MANUFACTURER DECLINES ALL RESPONSIBILITY FOR DAMAGE TO PERSONS OR PROPERTY RESULTING FROM THE FAILURE TO EARTH THE APPLIANCE OR FROM A DEFECTIVE EARTH CONNECTION.

IF THE APPLIANCE IS NOT CONNECTED TO THE ELECTRICAL POWER SUPPLY BY MEANS OF A PLUG, IT IS NECESSARY TO INSTALL AN ISOLATION SWITCH WITH A CONTACT OPENING GAP OF AT LEAST 3 MM.

THE PLUG ON THE POWER CORD AND THE CORRESPONDING SOCKET OUTLET MUST BE OF THE SAME TYPE, AND MUST CONFORM TO THE REGULATIONS IN FORCE. CHECK THAT THE VOLTAGE AND FREQUENCY OF THE ELECTRICAL POWER SUPPLY MATCH THE RATINGS ON THE NAME PLATE. AVOID USING ADAPTORS OR SHUNT CONNECTIONS.

NEVER UNPLUG THE APPLIANCE BY PULLING THE POWER CORD.

Safety instructions

•

AFTER INSTALLATION, THE PLUG MUST REMAIN ACCESSIBLE.

•

IN THE EVENT OF DAMAGE TO THE POWER CORD, HAVE IT REPLACED BY A QUALIFIED TECHNICIAN.

•

AFTER CHANGING THE POWER CORD, MAKE SURE THAT THE BRACKET WHICH SECURES THE CORD IS FIXED SECURELY IN PLACE.

IF THE APPLIANCE IS INSTALLED ON A CARPETED OR COVERED FLOOR, ENSURE THAT THE OPENINGS ON ITS UNDERSIDE ARE NOT OBSTRUCTED.

ALWAYS SWITCH OFF THE DISHWASHER AFTER EACH USE TO AVOID WASTING ELECTRICITY.

OBSOLETE APPLIANCES MUST BE RENDERED UNUSABLE. CUT OFF THE MAINS POWE R CORD AFTER UNPLUGGING IT FROM THE WALL O UTLE T, AND MAKE SAFE ANY COMPONENTS WHICH MIGHT BE DANGEROUS FOR CHILDREN (LOCKS, DOORS, ETC.). THE APPLIANCE MUST THEN BE TAKEN TO A SORTED WASTE COLLECTION CENTRE.

IN THE EVENT OF A FAULT, DISCONNECT THE DISHWASHER FROM THE ELECTRICAL POWER SUPPLY AND SHUT OFF THE WATER TAP. THEN CALL IN A QUALIFIED TECHNICIAN.

DO NOT USE APPLIANCES WHICH HAVE BEEN DAMAGED DURING TRANS IT! IF IN DOUBT, CONSUL T YO UR DEA LE R. THE APPLIANCE MUST BE INSTALLED AND CONNECTED IN ACCORDANCE WITH THE INSTRUCTIONS PROVIDED BY THE MANUFACTURER OR BY A QUALIFIED TECHNICIAN.

THE APPLIANCE IS INTENDED FOR USE BY ADULTS.

CHILDREN TO COME NEAR OR PLAY WITH THE DISHWASHER. KEEP CHILDREN AWAY FROM DETERGENTS AND FROM THE OPEN DISHWASHER DOOR. THE PACKAGING MATERIALS (PLASTIC BAGS, POLYSTYRENE, METAL BARS, ETC.) MUST NOT BE LEFT WITHIN THE REACH OF CHILDREN. KEEP CHILDREN AWAY FROM THE OPEN DISHWASHER. THE APPLIANCE MAY CONTAIN RESIDUES OF DETERGENT WHICH CAN CAUSE IRREVERSIBLE DAMAGE TO THE EYES, MOUTH, AND THROAT, AS WELL AS POSSIBLE DEATH BY SUFFOCATION.

DO NOT INTRODUCE SOLVENTS SUCH AS ALCOHOL OR TURPENTINE WHICH MAY CAUSE AN EXPLOSION.

DO NOT LOAD DISHES THAT ARE SOILED WITH ASH, WAX OR PAINTS.

DO NOT ALLOW

Safety instructions

LEANING OR S ITT ING ON THE DIS HWASHER DOOR WHEN O PEN MAY CAUSE THE APPLIANCE TO OVERTURN, PUTING PEOPLE AT RISK.

DO NOT DRINK THE WATER RESIDUES WHICH MAY BE PRESENT INSIDE THE DISHES OR DISHWASHER AT THE END OF THE WASHING PROGRAM AND BEFORE THE DRYING CYCLE.

KNIVES OR OTHER SHARP-ENDED COOKING UTENSILS MUST BE PLACED IN THE CUTLERY BASKET BLADE-DOWN, OR LAID HORIZONTAL IN THE TOP BASKET. TAKE CARE NOT TO CUT YOURSELF AND ENSURE THAT THEY DO NOT PROJECT FROM THE BASKET.

AQUASTOP MODELS

THE AQUASTOP DEVICE PREVENTS FLOODING IN THE EVENT OF A WATER LEAK. WHEN THE AQUASTOP DEVICE IS TRIPPED, CALL IN A QUALIFIED TECHNICIAN TO IDENTIFY AND REPAIR THE FAULT. IN MODELS EQUIPPED WITH THE AQUSTOP DEVICE, THERE IS A SOLENOID VALVE INSIDE THE WATER INTAKE HOSE.

HO SE AND DO NO T ALLOW THE SOLENOID VALVE TO DROP INTO WATER.

DISCONNECT THE APPLIANCE FROM THE ELECTRICAL POWER SUPPLY AND FROM THE WATER SUPPLY.

IN THE EVENT OF DAMAGE TO THE WATER INTAKE HOSE,

DO NOT CUT THE

IMMEDIATELY AFTER INSTALLING THE DISHWASHER, PERFORM A QUICK TEST OF THE APPLIANCE FOLLOWING THE INSTRUCTIONS BELOW. IF THE DISHWASHER FAILS TO OPERATE CORRECTLY, DISCONNECT IT FROM THE ELECTRICAL POWER SUPPLY AND CALL THE NEAREST TECHNICAL SERVICE CENTRE.

APPLIANCE.

THE DISHWASHER MEETS ALL THE REQUIREMENTS SET OUT BY THE REGULATIONS IN FORCE CONCERNING SAFETY A ND ELECTRICAL EQUIPMENT. ANY TECHNICAL CHECKS SHOULD BE CONDUCTED EXCLUSIVELY BY A TRAINED AND AUTHORISED TECHNICIAN:

CARRIED OUT BY UNAUTHORISED PERSONS WILL INVALIDATE THE WARRANTY, AS WELL AS POSING A POTENTIAL HAZARD TO THE USER.

The manufacturer declines all responsibility

DO N O T AT TEMPT TO RE P AIR T HE

REPAIRS

for damage to persons or property resulting from failure to observe the above precautions, from tampering with even a single component of the appliance, or from the use of non original spare parts.

Installation instructions

2. Installation and hook-up

Remove the polystyrene basket retainers. Position the appliance in the desired place of installation. The back or sides of the dishwasher may be placed up against walls or other furniture units. If the dishwasher is installed near a heat source, fit the special insulating panel to prevent overheating and malfunction of the appliance. To ensure stability, install integrated or built-under dishwashers only under continuous worktops, and screw them to the adjacent units. To facilitate the installation procedure, the intake and drain hoses can be positioned in any direction; make sure that the hoses are not kinked, crushed or pulled too tightly. A hole at least 8 cm in diameter is required to allow the power supply cable and pipes to pass.

Level the appliance on the floor using its adjustable feet. This operation is essential for ensuring correct operation of the dishwasher.

For free-standing models only: if the appliance is not built-in and is therefore accessible on one side, the door hinge area must be covered for safety reasons (injury hazard). The covering fixtures are available as an accessory from specialist dealers or the After-Sales Service.

Some models are equipped with only one adjustable foot at the rear, which can be adjusted by turning the screw on the lower front part of the appliance.

2.1 Water supply connection

Preventing the risk of clogging or damage: if the water pipe is new or

has not been used for a long time, before connecting to the water supply check that the water is clear and free of impurities, to prevent damage to the appliance.

The dishwasher must always be connected to the water system with new hoses; old or used hoses must never be reused.

Installation instructions

CONNECTING TO THE WATER SUPPLY

Connect the intake hose to a cold water supply with ¾” gas thread, inserting the filter A supplied with the dishwasher.

place with your hands and then complete by tightening about ¼ of a turn with pliers.

In dishwashers equipped with the ACQUASTOP device, the filters is already fitted inside the threaded ring.

Take care to screw the hose firmly into

The dishwasher can also be connected to a hot water supply

exceeding 60°C

washing time by approximately 20 minutes, but slightly reduces its effectiveness. Make the connection to the domestic hot water supply using the same procedure described for connecting to the cold water supply.

DRAIN CONNECTION

Insert the dishwasher’s drain hose into a drain pipe having a diameter of at least place it inside the kitchen sink using the plastic support provided, taking care not to crush or excessively bend the hose. It is important to prevent the hose from coming loose and falling. For this purpose, the plastic support is equipped with a hole for tying it to the wall or water tap.

The free end should be positioned at a height of between

cm,

and should never be submerged in water. If a horizontal drain extension hose is used (for a maximum of 3 m) the drain hose can be placed at a maximum height of

. Supplying the appliance with hot water cuts down the

4 cm

, or alternatively,

85 cm

from the ground.

30 and 100

not

2.2 Electrical connection

Plug the power cord into a suitable electrical outlet, according to the instructions given in chapter "1. Safety and operating instructions".

User instructions

3. Description of the controls

3.1 Front panel

All the dishwasher controls are grouped on the front panel.

1 ON/OFF

2 SELECTION PROGRAM

3 ECO DRYING CYCLE

4 DELAY PROGRAM

5 START/STOP

6 POWER ON

7 PROGRAM PHASE

INFORM ATIO N

RECESSED DOOR HANDLE

BUTTON

BUTTONS

BUTTON

LIGHT

INDICATOR LIGHTS

DISPLAY

3.2 Information display

The dishwasher is equipped with a practical

DISPLAY

programmed dishwasher functions.

LIGHTING

Pressing the the dishwasher pilot light operation the depend upon the state of the dishwasher.

ON/OFF

DISPLAY (8)

(1)

button

(6)

. After approximately

will be turned on with a visualization that will

which provides information on the

will start the dishwasher and will lit up

(P1…P5)

3 second

from this

TABLE OF PROGRAMS

PROGRAM SELECTION

SOAK

QUICK

ECO

(*)

DAILY

STRONG

DELICATE

BIO

NORMAL

EC O

DRYI NG

(OPTIONAL)

TY PE A ND G RA DE DI RT

PANS AND DISHES IN WAITING

OF COMPLETING THE LOAD

DISHES NOT MUCH DIRTY

AND WITH "FRESH DIRT"

WITHOUT RESIDUAL DRY

PANS AND DISHES

NOT VERY DIRTY

BUT WITH DRY RESIDUALS

PANS AND DISHES

WITH NORMAL DIRT,

WITHOUT DRY RESIDUAL

PANS AND DISHES

VERY DIRTY

DISHES NOT VERY DIRTY

PANS AND DISHES DIRTY

AND WITH DRY RESIDUALS

PANS AND DISHES DIRTY

AND WITH DRY RESIDUALS

PROGR ESS PROG RAM

PREWASH WASH COLD RINS E HOT RINSE DRY

COLD

_ _ _ _

38°C

YES

58°C

55°C YES 68°C YES

65°C YES 68°C YES

70°C

YES

68°C

45°C YES 68°C YES

55°C YES 68°C YES

65°C YES 68°C YES

YES

Only

run the soak program with half loads.

(*) Reference program as EN 50242 standard.

(-) Not present.

If the dishwasher door is left open or is not properly closed, the INFORMATION DISPLAY (8) will signal that the washing program cannot be started.

For any other information about use and maintenance of the dishwasher, read the enclosed manual carefully.

SUPER

In programs containing the symbol, the

PANS AND DISHES

VERY DIRTY

AND WITH DRY RESIDUALS

ECO drying cycle option

45°C 70°C

YES

is available. This activates the ventilation system which allows

the dishes to be dried at lower temperatures (energy saving). With this option active, the program times are longer.

68°C

YES

19 592 0001 03

User instructions

PROGRAMMING

In this dishwasher model all the programming operations are possible only with closed door. With open door, on the the symbols -- and the

SELECTION PROGRAM

By pressing the relative button of desired program (see table) it will lid up the relative pilot light to confirm that the operation did occurred on the

DISPLAY (8)

will appear a program duration forecasting (“

PILOT LIGHT PROGRAMS (7)

The program selection is possible through the relative buttons

DISPLAY (8)

remains out.

h.mm

will appear

(2)

”).

START PROGRAM

At this point, in order to start the machine, it is only enough to press the

START/STOP (5)

to flash and confirmation “beep” is heard. From this moment the cycle dration on the This phase, that updates itself during the cycle, is “indicative” since it is influenced by the washing conditions such as dishwasher type and quantity, entry temperature etc. For this reason it is normal to see the updating during a program (increment and decrease of minutes) specially in the passage from one phase to the other (for example, from washing to rinse).

END PROGRAM

The end of the program is indicated by a short signal acoustic and from

End

the “ buttons, the “ dishwasher is ready to continue a new cycle, the same thing happens when closing or opening the door or by switching on-off the machine.

” visual notification on

for some seconds until the writtin “

DISPLAY (8)

End

” visual signal will vanish from the display and the

starts to decrease.

DISPLAY (8)

Time to end

. By pressing one of the

” start

User instructions

INTERRUPTION OF A PROGRAM

In order to interrupt a running program it is necessary:

•

to press the

writting “ At this point,it is possible to start the cycle again, otherwise:

TO CHANGE A PROGRAM

To change the running program it is necessary:

•

to interrupt the running program (see “

•

select the new program;

•

to press again the

program.

STOPPING A PROGRAM

To stop a program in progress, it must first be interrupted

(see “

NTERRUPTION OF A PROGRAM

START/STOP (5)

Time to end

Now press buttons P1+P2 simultaneously and

the first three program lights will come on.

for some seconds until when the

” remains lit on the display (confirmation beep).

NTERRUPTION OF A PROGRAM

START/STOP

button

(5)

to make start the new

”).

”);

The display will show “P0” and the dishwasher will immediately switch to the end of the cycle and drain the tank (during this process, the

Time to end

“

” message willflash).

When the drain procedure ends, the end of cycle message "End"

appears on the display.

In case that the door is opened during the operation, to the next door closing it is going to be necessary to start the program as shown in paragraph “S

TART PROGRAM

”. The program will resume from the point in

which it was interrupted.

In case that the tub temperature is higher than 50°C the program will start about 30 seconds later.

If the dishwasher door is left open or is not properly closed, the INFORMATION DISPLAY (8) will signal that the washing program cannot be started.

+ 23 hidden pages