Contents
1. INSTRUCTIONS FOR SAFE AND PROPER USE________________ 4
2. INSTALLATION __________________________________________ 6
3. DESCRIPTION OF CONTROLS ____________________________ 10
4. USE OF THE OVEN______________________________________ 16
5. AVAILABLE ACCESSORIES _______________________________ 17
6. COOKING HINTS________________________________________ 18
7. CLEANING AND MAINTENANCE ___________________________ 24
8. EXTRAORDINARY MAINTENANCE _________________________ 28
Thank you for having preferred our product. From now on we feel sure
you will enjoy creatively using your new oven.
We recommend you to carefully read the instructions in this manual. A
lot of room has been given to the best and most correct way of using the
oven. These instructions will also make it easier for you to become
acquainted with each single component or accessory.
Useful hints are provided on how to use pans and cooking utensils, on
correct guide positions and control settings.
Be sure to follow the cleaning instructions carefully. That way your oven
will give you many long years of reliable service.
The single paragraphs illustrate oven operation, step by step. The text is
easy to understand and completed with pictures and some of the most
commonly used pictograms.
By reading this manual carefully, you will find all the answers to your
oven operation queries.
INSTRUCTIONS FOR THE INSTALLER: these are intended for the
qualified technician who must install the appliance, set it functioning
and carry out an inspection test.
INSTRUCTIONS FOR THE USER: these contain user advice,
description of the commands and the correct procedures for cleaning
and maintenance of the appliance.
3
Introduction
1. INSTRUCTIONS FOR SAFE AND PROPER USE
THIS MANUAL IS AN INTEGRAL PART OF THE APPLIANCE AND
THEREFORE MUST BE KEPT IN ITS ENTIRETY AND IN AN ACCESSIBLE
PLACE FOR THE WHOLE WORKING LIFE OF THE OVEN. WE ADVISE
CAREFUL READING OF THIS MANUAL AND ALL THE INSTRUCTIONS
THEREIN BEFORE USING THE OVEN. INSTALLATION MUST BE CARRIED
OUT BY QUALIFIED PERSONNEL IN ACCORDANCE WITH THE
REGULATIONS IN FORCE. THIS APPLIANCE IS INTENDED FOR DOMESTIC
USES AND CONFORMS TO CURRENT REGULATIONS IN FORCE. THE
APPLIANCE HAS BEEN BUILT TO CARRY OUT THE FOLLOWING
FUNCTIONS: COOKING AND HEATING-UP OF FOOD. ALL OTHER USES
ARE CONSIDERED IMPROPER.
THE MANUFACTURER DECLINES ALL RESPONSIBILITY FOR IMPROPER
USE.
DO NOT LEAVE THE PACKING IN THE HOME ENVIRONMENT. SEPARATE
THE VARIOUS WASTE MATERIALS AND TAKE THEM TO THE NEAREST
SPECIAL GARBAGE COLLECTION CENTRE.
BEFORE THROWING AWAY AN OLD APPLIANCE, MAKE SURE THIS IS
RENDERED HARMLESS AND DISPOSE OF IT THROUGH A PRE-SORTED
WASTE COLLECTION CENTRE.
IT IS OBLIGATORY FOR THE ELECTRICAL SYSTEM TO BE GROUNDED
ACCORDING TO THE METHODS REQUIRED BY SAFETY RULES.
WHEN LINKING UP TO MAINS BY PLUG AND SOCKET, MAKE SURE THAT
BOTH ARE COMPATIBLE AND CONNECT BY MEANS OF A POWER CABLE
COMPLYING WITH APPLICABLE REGULATIONS.
THE SOCKET MUST BE ACCESSIBLE AFTER THE APPLIANCE HAS BEEN
BUILT IN.
NEVER UNPLUG BY PULLING ON THE CABLE.
DO NOT OBSTRUCT VENTILATION OPENINGS AND HEAT DISPERSAL
SLITS.
IMMEDIATELY AFTER INSTALLATION CARRY OUT A BRIEF INSPECTION
TEST OF THE OVEN, FOLLOWING THE INSTRUCTIONS BELOW. SHOULD
THE APPLIANCE NOT FUNCTION, DISCONNECT IT FROM THE SUPPLY AND
CALL THE NEAREST TECHNICAL ASSISTANCE CENTRE.
NEVER TRY TO REPAIR THE APPLIANCE BY YOURSELF!
IN CASE OF ONGOING FAULTS, TURN THE MAIN SWITCH OFF,
DISCONNECT THE POWER SUPPLY AND CONTACT YOUR NEAREST
DEALER. ALWAYS INSIST ON ORIGINAL SPARE PARTS.
4
Introduction
ALWAYS CHECK THAT THE CONTROL KNOBS ARE IN THE “ZERO” (OFF)
POSITION WHEN YOU FINISH USING THE OVEN.
NEVER PUT INFLAMMABLE OBJECTS IN THE OVEN: THEY COULD BE
ACCIDENTALLY LIGHTED AND CAUSE FIRES.
THE I.D. PLATE WITH TECHNICAL DATA, REGISTRATION NUMBER AND
BRAND NAME IS POSITIONED VISIBLY ON THE OVEN DOOR FRAME.
THE PLATE MUST NOT BE REMOVED.
THE OVEN IS DESIGNED FOR USE BY ADULTS. DO NOT ALLOW CHILDREN
TO GO NEAR OR PLAY WITH IT.
DURING THE AUTOMATIC CLEANING CYCLE (PYROLYSIS) THE OUTER
DOOR WINDOW COULD BECOME HOTTER THAN NORMAL. KEEP
CHILDREN AT A DISTANCE.
THIS APPLIANCE IS MARKED ACCORDING TO THE EUROPEAN DIRECTIVE
2002/96/EC ON WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT
(WEEE).
THIS GUIDELINE IS THE FRAME OF A EUROPEAN-WIDE VALIDITY OF
RETURN AND RECYCLING ON WASTE ELECTRICAL AND ELECTRONIC
EQUIPMENT.
BEFORE THE APPLIANCE IS PUT INTO OPERATION, ALL THE LABELS AND
PROTECTIVE FILMS APPLIED INSIDE OR OUTSIDE MUST BE REMOVED.
The manufacturer declines all responsibility for damage to persons
or things caused by non-observance of the above prescriptions or by
interference with any part of the appliance or by the use of non-original
spares.
5
Instructions for the installer
2. INSTALLATION
2.1 Electric installation - mains supply
WARNING: This appliance must be earthed.
This appliance conforms with BSEN 55014 regarding radio frequency
interference.
• The appliance must be connected by a competent electrical contractor /
engineer such as one who is registered with the National Inspection Council
for Electrical Contracting (NIEIC).
• A Double Pole Control Switch with a minimum contact clearance of 3 mm
must be fitted on or recessed into the wall adjacent to the appliance and
must be accessible after installation to enable the appliance to be isolated for
cleaning or in case of an emergency.
• The appliance should be checked to ensure that the rated voltage
corresponds with supply voltage.
• Color coding of wiring:
GREEN- and YELLOW = EARTH
BLUE = NEUTRAL
BROWN = LIVE
As the colours of the wires in the mains lead of this appliance may not correspond
with the colour markings identifying the terminals in your plug, proceed as follows:
The wire coloured Green-and-Yellow must be connected to the terminal marked
with "E" or ; The wire coloured Blue must be connected to the terminal
marked "N" or coloured Black; The wire coloured Brown must be connected to the
terminal marked "L" or coloured Red.
2.2 Electrical connection
Check that mains voltage and power cable ratings are as per the
indications provided on the label attached to the oven door frame.
This label must never be removed.
It is obligatory for the electrical system to be grounded according to the
methods required by safety rules.
If a plug and socket connection is being used make sure that the plug
and socket are compatible. Avoid use of adapters and shunts as these
could cause overheating and risk of burns.
If a fixed connection is being used fit power line with an omnipolar circuit
breaker with a contact opening gap equal to or greater than 3 mm in an
easily accessible position in proximity to the oven.
6
Instructions for the installer
2.2.1 Ovens with top controls
In the ovens with top controls the power cable is not supplied. Use a
H05RR-F or H05RN-F rubber-sheathed cable making sure that it does
not come into contact with any external metal parts of the oven when
routing. Remove rear cover by loosening relevant screws to gain access
to the terminal strip. If necessary change jumper configuration as shown
in the figure and then connect wires making sure that the earth wire is at
least 20 mm longer than the others. Secure power cable to oven by
means of the appropriate fitting.
.
For operation on 230V∼: use an H05RR-F
/ H05RN-F type three-core cable (3 x 2.5
2
mm
).
For operation on 400V2N∼: use an
H05RR-F / H05RN-F type four-core cable
(4 x 2.5 mm
2
).
For operation on 400V3N∼: use an
H05RRF / H05RN-F type five-core cable
(5 x 1.5 mm2).
The cable end to be connected to the
appliance must be provided with an ground
wire (yellow-green) at least 20 mm longer.
The manufacturer declines all responsibility for damage to persons
or things caused by non-observance of the above prescriptions or by
interference with any part of the appliance.
7
Instructions for the installer
2.3 Mounting the oven
The oven is designed for mounting into any piece of kitchen furniture
being heat-resistant. Proceed according to the dimensions shown in
Figures 1, 2 and 3. For installing under a work top, follow the dimensions
given in Figure 1-3. For installing under a work top with combined heating
plates, ensure a minimum clearance from any side walls of at least 110
mm as shown in Figure 1.
For installing in a column, follow the dimensions given in Figure 1-2
allowing for a clearance of 80 to 90 mm at the top and sides of the
column. Tighten the four screws A inside the frame to secure (Fig. 1).
For installing beneath a non-integrated top, allow for a rear and bottom
clearance as shown in Figure 1 (ref. B). See relevant instructions for
fitting and securing the cook top.
8
Instructions for the installer
Never use the oven door to lever the oven into
place when fitting. Avoid exerting too much
pressure on the oven door when open.
2.4 Connecting the cook top to the oven
Once installed, the cook top must be connected to the oven. Mount the
oven allowing enough room for the following operations to be made.
• Connect the earth wire (yellow-green) of the cook top to the earth
terminal A of the oven (see figure).
• Fit the cook top connectors into the appropriate sockets in the top
cover of the oven. Make sure that the colours and symbols of the
connectors match those of the oven sockets.
• If the cook top is equipped with a connector for the residual heat
indicator, same must be fitted into the free socket on the right side.
The oven can now be fully mounted into the cabinet; make sure that the
power cable is properly routed and does not come into contact with parts
which may become hot during operation.
9
Instructions for the user
3. DESCRIPTION OF CONTROLS
3.1 Front control panel
All the oven controls are grouped together on the front panel.
MODEL: JRS 30
DOOR LOCK INDICATOR LIGHT
When this light comes on during automatic cleaning
(pyrolysis), the door lock device is operative.
THERMOSTAT INDICATOR LIGHT
When this light comes on, the oven is heating up. When this
light goes out, the preset heating temperature has been
reached. When the light flashes, the temperature inside the
oven is steady at the set temperature.
This light also comes on during the automatic cleaning cycle (pyrolysis)
and goes out when the set time has passed.
THERMOSTAT KNOB
Cooking temperature is selected by turning the
knob clockwise to the desired setting, between
50° and 250°C.
In the JRP 30 model, maximum temperature is
280°C.
MODEL: JRS 31
MODEL: JRP 30
10
Instructions for the user
FUNCTION SWITCH KNOB
Rotate the knob in either direction to select
desired function from the following:
NO FUNCTION SET
UPPER AND LOWER
HEATING ELEMENT
GRILL ELEMENT GRILL ELEMENT +
UPPER AND LOWER HEATING
ELEMENT + VENTILATION
VENTILATION
LOWER HEATING ELEMENT
UPPER AND LOWER HEATING
ELEMENT + VENTILATED
HEATING ELEMENT
DEFROSTING AUTOMATIC CLEANING CYCLE
VENTILATED HEATING ELEMENT
GRILL + ROTISSERIE
(PYROLYSIS)
COOK TOP CONTROL KNOB
Permits to adjust cook top heating.
Rotate clockwise to set to desired
value (2 to 12).
COOK-TOP CONTROL KNOB
WITH DOUBLE HEATING
Permits to select heating zone in plates with double heating
zones.
Rotating the knob clockwise from between 2 to 12 heats the inner zone
within the small diameter.
Turn the knob all the way around beyond 12 and release. This causes the
knob to return to 12 and both diameters to heat up. To adjust heat
intensity, turn the knob anticlockwise to the desired value.
To return to heating inside the inner zone only, set knob first to 0 and
then to any value between 2 and 12 as desired.
11
Instructions for the user
3.2 Electronic programmer
LIST OF FUNCTIONS
MINUTE-COUNTER KEY
COOKING TIME KEY
END-OF-COOKING KEY
MANUAL OPERATION KEY
TIME BACK KEY
TIME FORWARD KEY
3.2.1 Clock adjustment
When using the oven for the first time, or after a power failure, the display
flashes regularly and indicates
on the display. By pressing keys
. To stop flashing, press key
or each single press changes
the time by 1 minute either up or down.
Press one of the two keys until the right time appears.
Before setting the programmer activate the desired function and
temperature.
3.2.2 Semiautomatic cooking
Use this setting for automatic oven switch-off at the end of cooking time.
12
Instructions for the user
By pressing key
pressed and at the same time, press keys
, the display lights up, showing ; keep the key
or to set the cooking
time.
Release key
display will now show the right time together with symbols AUTO and
to start the programmed cooking time count. The
.
3.2.3 Automatic cooking
Use this setting to automatically start and stop the oven.
By pressing key
pressed and at the same time, press keys
, the display lights up showing ; keep the key
or to set the cooking
time.
By pressing key
the sum of the right time + cooking time will appear;
keep the key pressed and at the same time, press keys
or to
regulate the end of cooking time.
Release key
the right time together with symbols AUTO and
to start the programmed count and the display will show
.
After setting, to see how much cooking time is left, press key ; to see
end of cooking time, press key .
3.2.4 End of cooking
When cooking is over, the oven will automatically switch off and, at the
same time, an intermittent alarm will sound. After switching off the alarm,
13
Instructions for the user
the display will once again show the right time together with the symbol
, indicating that the oven has returned to manual operation mode.
3.2.5 Adjusting alarm volume
The acoustic alarm has three different settings. These can be operated,
while the alarm is sounding, by pressing key
.
3.2.6 Switching off the alarm
The alarm switches off automatically after seven minutes. It can be
manually turned off by pressing key
.
3.2.7 Minute-counter
The programmer can also be used as a simple minute counter.
The use of the minute-counter will not interrupt oven operation at the end
of the set time.
By pressing key
and at the same time press keys
the programmed count starts and the symbols
monitor.
, the display shows ; keep the key pressed
or . By releasing the key ,
and appear on the
After programming the minute-counter, the display will show the right
14
time. to display remaining time, press key .
Wrong settings are prevented logically (e.g., any conflict between end of
cooking time and a longer time will not be accepted by the programmer).
Instructions for the user
3.2.8 Cancellation of set data
Once the programme has been set, keep the key of the function to be
cancelled pressed, while at the same time is reached by means
of variation keys
end-of-cooking time by the programmer.
3.2.9 Changing the set data
The cooking data entered can be changed at any time by keeping the
function key pressed and at the same time adjusting the keys
.
or . Time cancellation will be considered as
or
15
Instructions for the user
4. USE OF THE OVEN
Before turning on the oven, make sure that the symbol (see "3.2.1
Clock adjustment") appears on the display.
4.1 Warnings and general advice
Before using the oven for the first time, pre-heat it to maximum
temperature long enough to burn any manufacturing oily residues which
could give the food a bad taste.
After a power failure, the display will flash at regular intervals showing
. To regulate, refer to paragraph "3.2 Electronic programmer ".
During cooking, do not cover the bottom of the oven with aluminium or
tin foil and do not place pans or oven trays on it as this may damage the
enamel coating. If you wish to use greaseproof paper, place it so that it
will not interfere with the hot air circulation inside the oven.
To prevent any steam in the oven creating
problems, open the door in two stages: half open
(5 cm approx.) for 4-5 seconds and then fully
open. To access food, always leave the door
open as short a time as possible to prevent the
temperature in the oven from falling and ruining
the food.
16
4.2 Cooling ventilation
The appliance is fitted with coolings fan which
come on when the oven is turned on.
The fans cause a flow of air which comes out of the
lower part of the oven front and which may briefly
continue after the oven has been turned off.
PYROLYSIS: once the cleaning cycle has started,
the fans only operate when the oven has achieved
a preset temperature.
4.3 Oven light
To turn on the light, set the function selector knob to any symbol or, with
oven turned off, simply open the door.
Instructions for the user
5. AVAILABLE A CCESSORIES
The oven features 4 support positions
for plates and racks of different height.
Some models do not feature all accessories.
Grill: useful for holding cooking vessels.
Plate grill: for placing above plate for
cooking foods that might drip.
Tubular tray-holder rack: for cooking food
on plates, small cakes, roasts or food
requiring light grilling.
Oven plate: useful for catching fat from
foods on the grill above.
Pastry plate: for baking cakes, pizza and
oven desserts.
Rotisserie frame: to be mounted in the
oven guides before fitting the spit.
Rotisserie: suitable for cooking whole
chickens, sausages and any other food
requiring even cooking on all surfaces.
Roof liner/Grill guard: removing this
simplifies cleaning procedures inside the
oven.
Chromium-plated tubular gripper for
removing hot racks and plates from the
oven.
Accessories available on request
Original accessories may be ordered from any Authorised Service
Centre.
17
Instructions for the user
6. COOKING HINTS
In fan-assisted mode preheating should be carried out at 30/40°C above
the cooking temperature. This considerably shortens cooking times and
reduces power consumption, as well as giving better cooking results.
6.1 Traditional cooking
FUNCTION SWITCH
THERMOSTAT SWITCH
50 ÷ 250°C
This traditional cooking method, in which heat comes from above and
below, is suitable for cooking food on a single level. You have to preheat the oven until the set temperature is reached. Place the food in the
oven only after the thermostat indicator light has turned off. very fatty
meats may be put in when the oven is still cold. Put frozen meat in
immediately, without waiting for it to thaw. The only precaution you need
to take is to set the temperature about 20°C lower and cooking time
about 1/4 longer than you would for fresh meat.
6.2 Hot-air cooking
FUNCTION SWITCH
THERMOSTAT SWITCH
50 ÷ 280°C
This system is suitable for cooking on several levels, including different
types of food (fish, meat etc.), without the tastes and smells mingling.
Air circulation in the oven ensures a uniform distribution of heat.
18
Instructions for the user
Multiple cooking is possible as long as the cooking temperature of the
different foods is the same.
6.3 Grill cooking
FUNCTION SWITCH
THERMOSTAT SWITCH
280°C
Permits rapid browning of foods. You are advised to place the pan in the
highest guide. For short-term cooking of small quantities, place the grid
in the fourth guide from the bottom. For long-term cooking and grills, put
the grid in the lowest guide in accordance with the size of the pieces.
Keep the oven door closed during grilling. Grilling with the door
open could permanently damage the oven and affect safety of
operation.
6.4 Hot-air grilling
FUNCTION SWITCH
THERMOSTAT SWITCH
280°C
Ensures uniform heat distribution with greater heat penetration into the
food. Food will be lightly browned on the outside and remain soft inside.
Keep the oven door closed during cooking. Heating up time must
not exceed 60 minutes.
Keep the oven door closed during grilling. Grilling with the door
open could permanently damage the oven and affect safety of
operation.
19
Instructions for the user
6.5 Delicate cooking
FUNCTION SWITCH
THERMOSTAT SWITCH
50 ÷ 280°C
Ideal for pastries and cakes with wet covering and little sugar and damp
desserts in moulds. Excellent results can also be achieved in completing
cooking at the bottom and with dishes requiring heat in the lower area in
particular. The plate is best inserted at bottom level.
6.6 Defrosting
FUNCTION SWITCH
0
THERMOSTAT SWITCH IN POSITION
The flow of air produced by the fan ensures quicker defrosting.
The air circulating inside the oven is at room temperature.
20
The advantage of defrosting at room temperature is that it does not alter
the taste and appearance of the food.
Instructions for the user
6.7 Rotisserie
FUNCTION SWITCH
THERMOSTAT SWITCH
280°C
This is an energy saving-cooking system. Place the food at the centre of
the plate or rack and cook as indicated in paragraph “6.3 Grill cooking”.
Recommended for small pieces only.
Prepare the food on the spit rod and block fork screws A. Insert the
frame B in the second level from the bottom. Remove handle D and
position the spit rod so the pulley E remains guided on frame B.
Completely fit frame B until the tip of the spit rod fits into hole C on the
back wall of the oven. Place an oven dish F on the bottom guide and
pour in a little water to prevent smoke from forming.
It is normal for the thermostat light to flash during cooking. This indicates
the temperature inside the oven is regular (above all when the oven door
is closed).
Make sure the food is centered well on the spit to ensure best results.
21
Instructions for the user
6.8 Recommended cooking table
Cooking times, especially meat, vary according to the thickness and
quality of the food and to consumer taste.
LEVEL
FIRST COURSES
LASAGNE
OVEN-BAKED PASTA
MEAT
ROAST VEAL
ROAST BEEF
ROAST PORK
CHICKEN
DUCK
GOOSE - TURKEY
RABBIT
LEG OF LAMB
FISH 1 - 2 170 - 200 ACCORDING TO
PIZZA 1 - 2 210 - 240 40 - 45
DESSERTS
SHORT PASTRY
CIAMBELLA
BRIOCHES
FRUIT CAKE
PARADISE CAKE
APPLE CAKE
RICE CAKE
(*) = WITH PREHEATED OVEN
LEVEL
FIRST SURFACE SECOND SURFACE
PORK CHOPS
FILLET OF PORK
FILLET OF BEEF
LIVER
VEAL ESCALOPES
HALF CHICKEN
SAUSAGES
MEAT-BALLS
FISH FILLETS
TOAST
TRADITIONAL COOKING
FROM BELOW
2 - 3
2 - 3
2
2
2
2
2
2
2
2
1 - 2
1 - 2
1 - 2
1 - 2
1 - 2
1 - 2
1 - 2
TEMPERATURE
(°C)
210 - 230
210 - 230
170 - 200
210 - 240
170 - 200
170 - 200
170 - 200
140 - 170
170 - 200
170 - 200
170 - 200
165
170 - 200
170 - 200
170
190
180
TIME
IN MINUTES (*)
30
40
30 - 40 / KG.
30 - 40 / KG.
30 - 40 / KG.
45 - 60
45 - 60
45 - 60
50 - 60
40 - 50
DIMENSIONS
15 - 20
35 - 45
40 - 45
20 - 30
60
60
60
GRILLING
FROM BELOW
4
3
3
4
4
3
4
4
4
4
TIME IN MINUTES
7 - 9
9 - 11
9 - 11
2 - 3
7 - 9
9 - 14
7 - 9
7 - 9
5 - 6
2 - 4
5 - 7
5 - 9
9 - 11
2 - 3
5 - 7
9 - 11
5 - 6
5 - 6
3 - 4
2 - 3
22
Instructions for the user
LEVEL
FIRST COURSES
LASAGNE
OVEN-BAKED PASTA
CREOLE RICE
MEAT
ROAST VEAL
ROAST PORK
ROASTED BEEF
FILLET OF BEEF
ROAST LAMB
ROAST BEEF
ROAST CHICKEN
ROAST DUCK
ROAST TURKEY
ROAST RABBIT
ROAST HARE
ROAST PIGEON
FISH 2 - 3 150 - 170 ACCORDING
PIZZA
BREAD
TOAST
DESSERTS
CIAMBELLA
FRUIT CAKE
BRIOCHES
SHORT PASTRY
RICE CAKE
APPLE CAKE
PARADISE CAKE
HOT-AIR COOKING
FROM BELOW
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2 - 3
2 - 3
1 - 2
2 - 3
2 - 3
2 - 3
2 - 3
2 - 3
2 - 3
2 - 3
TEMPERATURE
(°C)
190 - 210
190 - 210
190 - 220
150 - 170
150 - 160
160 - 170
160 - 180
130 - 150
170 - 180
170
160 - 170
150 - 160
150 - 160
160 - 170
140 - 170
210 - 240
190 - 210
220 - 240
150 - 170
170 - 190
160 - 170
170 - 180
170
180
160
TIME
IN MINUTES
20 - 25
25 - 30
20 - 25
65 - 90
70 - 100
65 - 90
35 - 45
100 - 130
40 - 45
70 - 90
100 - 160
160 - 240
80 - 100
30 - 50
15 - 25
TO DIMENSIONS
30 - 50
40
7
35 - 45
40 - 50
40 - 60
20
60
60
60
23
Instructions for the user
7. CLEANING AND MAINTENANCE
Before performing any operations requiring access to powered
parts, switch off the power supply to the machine.
7.1 Cleaning stainless steel
To keep stainless steel in good condition it should be cleaned regularly
after use. Let it cool first.
7.2 Door glass
Always keep this clean. Use absorbent kitchen paper. In the case of
persistent dirt, wash with damp sponge and regular detergent.
7.3 Outer oven structure
Wash with water and regular detergent.
7.4 Enamelled parts
Wait for the oven to cool, take out all the removable parts and proceed to
wash with water and regular detergent.
Dry and replace components.
24
For cleaning enamelled parts, never use abrasive products, metal
wire sponges or sharp objects so as not to damage the surface.
Remove any dried remains of food on surfaces with a wooden or
plastic utensil.
Instructions for the user
7.5 Cleaning of the oven
For best oven upkeep clean regularly after having allowed to cool. Take
out all removable parts.
• Clean the oven grill and side guides with hot water and non-abrasive
detergent. Rinse and dry.
• Clean the internal walls of the oven with a soft ammoniac-soaked
cloth. Rinse and dry. If there are still stains or drops, place a damp
ammoniac-soaked cloth on the bottom of the oven, close the door
and after a few hours wash the oven with hot water and liquid
detergent. Rinse and dry.
7.6 Pyrolysis: automatic oven cleaning
Pyrolysis is an automatic high-temperature cleaning method which
causes dirt to dissolve.
BEFORE STARTING THE AUTOMATIC CLEANING CYCLE, MAKE SURE THE
OVEN IS EMPTY AND DOES NOT CONTAIN FOOD OR ANYTHING ELSE.
A DOOR LOCK DEVICE PREVENTS THE DOOR BEING OPENED.
IN CASE THE OVEN IS INSTALLED UNDER A COOKTOP, MAKE SURE THAT
DURING THE AUTOMATIC CLEANING CYCLE ANY GAS OR ELECTRIC HOBS
ARE TURNED OFF.
IN CASE A MICROWAVE OVEN IS INSTALLED ABOVE THE OVEN, MAKE
SURE DEVICE IS SWITCHED OFF DURING PYROLITIC CYCLE.
25
NOT VERY DIRTY DIRTY VERY DIRTY
DURATION OF
CLEANING :
Instructions for the user
7.6.1 Before starting the automatic cleaning cycle
The Pyrolysis process can be performed at any time of the day or night
(to take advantage of lower night-time electricity rates).
Before proceeding, check the following:
• remove all the accessories from the oven (some of them will not
withstand heat and become damaged and/or deformed);
• remove the most obvious traces of dirt (Pyrolysis cleaning would
take too long);
• make sure the oven door is properly closed;
• when setting the cleaning cycle, remember the following:
90 MIN. 105 MIN. 120 MIN.
THE FIRST AUTOMATIC CLEANING CYCLE COULD CAUSE BAD SMELLS
DUE TO EVAPORATION OF OILY SUBSTANCES USED DURING
MANUFACTURE.
THIS IS A QUITE NORMAL OCCURRENCE WHICH DISAPPEARS AFTER THE
FIRST CLEANING CYCLE.
DURING THE AUTOMATIC CLEANING CYCLE, THE FANS MAKE MORE
NOISE DUE TO GREATER ROTATION SPEED. THIS IS QUITE NORMAL AND
IS INTENDED TO FAVOUR THE ELIMINATION OF HEAT. AFTER PYROLYSIS,
VENTILATION CONTINUES AUTOMATICALLY FOR LONG ENOUGH TO
PREVENT THE CABINET WALLS AND FRONT OF THE OVEN FROM
OVERHEATING.
7.6.2 How the automatic cleaning cycle works
The following table shows an example of automatic cleaning cycle
operation.
When the cleaning cycle is set, the thermostat light comes on, while the
door lock device (and indicator light) is not engaged.
When the temperature reaches 300°C, a lock device triggers to prevent
door opening.
At the end of the cleaning cycle, the thermostat indicator light goes off.
The door-lock is only released afterwards when the temperature inside
the oven has dropped below 300°C.
26
Instructions for the user
ON
ON
OFF
OFF
-
300 °C
500 °C
300 °C
7.6.3 Setting the automatic cleaning cycle
FUNCTION SWITCH
MINIMUM DURATION OF CLEANING CYCLE
Position the function selector switch on the symbol : the thermostat
indicator light will come on and the programmer will automatically set on
a minimum pyrolysis time of
press key
and increase/decrease keys or . Pyrolysis time can
. To display or regulate this time,
be set to a maximum of 3 hours.
The cleaning cycle can be programmed so it starts at a specific time.
Press key
and change the setting by means of setting variation keys
or .
27
Instructions for the user
8. EXTRAORDINARY MAINTENANCE
The oven may require extraordinary maintenance or replacement of parts
subject to wear such as seals, bulbs, and so on. The following
instructions describe how to carry out these minor maintenance
operations.
Before any intervention, disconnect the power supply of the device.
8.1 Replacement of light bulb
Remove the bulb protector A by turning anticlockwise and change bulb B
with a similar one. Re-fit the bulb protector A.
28
Only use oven bulbs (T 300°C).
If in doubt ask your dealer.
Instructions for the user
8.2 Removing the door
Hold the door on both sides with both hands near hinges A and raise levers
B. Lift up the door forming an angle of about 45° and remove. To refit, slide
the hinges A in the grooves, drop the door and release levers B.
Move door carefully without brut forle. When door removed, be careful
with the hinges being under pressure.
8.3 Oven door seal (mod. JRS 30 / JRS 31)
To permit thorough cleaning of the oven, the seal
may be removed. Before removing the seal, take off
the door as described above. Once the door has
been taken off, lift the tabs at the corners as shown
in the figure.
After cleaning, refit the seal with the longer side
horizontal and insert the tabs into the appropriate
holes starting from the top ones.
29
Loading...