Smeg CWG411MDAUS-2 User manual [GB]

PROFESSIONAL DISHWASHER

SMEG

TABLE OF CONTENTS

1 PRECAUTIONS FOR SAFETY AND USE .......................................................................................................................2

1.1 Trademark ........................................................................................................................................................2

1.2 Name and address of manufacturer or distributor ..........................................................................................2

1.3 Declaration of conformity to product standards ..............................................................................................2

2 TECHNICAL DATA ......................................................................................................................................................3

3 INSTALLATION AND POSITIONING ............................................................................................................................5

4 INSTRUCTIONS FOR TECHNICAL STAFF .....................................................................................................................6

4.1 Plumbing hookup ..............................................................................................................................................6

4.2 Electrical connection ........................................................................................................................................6

5 FIRST START-UP ........................................................................................................................................................7

5.1 Using the water softener (on models with this feature only) ..........................................................................7

6 SET-UP (Authorised technical staff only) ..................................................................................................................8

6.1 Contents of display ...........................................................................................................................................9

6.2 Note on display of temperatures .....................................................................................................................9

6.3 Parameter programming procedure (setup) ....................................................................................................9

6.4 Modifiable parameters .................................................................................................................................. 10

6.5 Adjusting detergent and rinse aid dispensing ............................................................................................... 10

6.5.1 Adjusting rinse aid dispensing (only available on certain models) ........................................................ 10

6.5.2 Adjusting detergent dispensing (only available on certain models) ..................................................... 11

6.6 Starting the peristaltic pumps in manual mode – rapid filling of detergent and rinse aid circuit ................ 11

6.7 Adjusting the regeneration frequency (models with softener only) ............................................................. 11

6.8 Mains water hardness setting table .............................................................................................................. 11

7 MALFUNCTIONS SHOWN ON THE DISPLAY (FOR THE TECHNICIAN) ..................................................................... 12

8 INSTRUCTIONS FOR THE USER ............................................................................................................................... 13

8.1 Control panel ................................................................................................................................................. 13

8.2 Before washing .............................................................................................................................................. 14

8.3 First use each day (tank and boiler empty) ................................................................................................... 15

8.4 Choosing the program ................................................................................................................................... 16

8.5 Changing the program ................................................................................................................................... 16

9 MAINTENANCE AND CLEANING............................................................................................................................. 18

9.1 Daily cleaning of filters .................................................................................................................................. 18

SMEG

9.2 Routine inspection of the spray arms (once a week) .................................................................................... 18

9.3 Lengthy periods out of use ............................................................................................................................ 18

10 TROUBLESHOOTING .......................................................................................................................................... 19

11 MALFUNCTIONS SHOWN ON THE DISPLAY (FOR THE USER) ............................................................................ 20

SMEG Thanks you for choosing one of its products.

Read all the instructions in this manual carefully to become familiar with the right conditions for the proper use

of your dishwasher.

TECHNICAL INSTRUCTIONS

These are intended for the qualified staff who are to install, commission and test the appliance and carry out any servicing and repairs.

INSTRUCTIONS FOR THE USER

These provide recommendations for use, a description of the controls and the correct procedures for cleaning and maintaining the dishwasher.

1 PRECAUTIONS FOR SAFETY AND USE

1.1 Trademark

SMEG

1.2 Name and address of manufacturer or distributor

Smeg S.p.A.

Via Leonardo da Vinci, 4 - 42016 Guastalla (RE) Tel. +39 0522 8211 - Fax + 39 0522 821453 internet: www.smegfoodservice.com, email : fooddservice@smeg.it

Info :

INFORMATION AND SERVICE FOR SMEG PROFESSIONAL DISHWASHERS Our Sales Department staff will be able to provide you with information about prices and special offers. Our After-Sales Department will be able to provide you with guidance about keeping your appliance functioning correctly and put you in touch with your nearest authorised Service Centre. Our entire product offering can be viewed at:

1.3 Declaration of conformity to product standards

THIS APPLIANCE IS TAGGED UNDER EUROPEAN DIRECTIVE 2002/96/EC ON WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT (WEEE). BY MAKING SURE THAT THIS PRODUCT IS DISPOSED OF CORRECTLY THE USER HELPS TO PREVENT POTENTIAL DETRIMENTAL EFFECTS ON HEALTH AND THE ENVIRONMENT. WHEN DECOMMISSIONING THE APPLIANCE COMPLY WITH THE LOCAL WASTE DISPOSAL REGULATIONS. FOR FURTHER INFORMATION ON THE TREATMENT, RECOVERY AND RECYCLING OF THIS PRODUCT, CONTACT THE COMPETENT LOCAL OFFICE, THE DOMESTIC WASTE COLLECTION SERVICE, OR THE SHOP WHERE THE PRODUCT WAS PURCHASED. THE APPLIANCE MUST BE GROUNDED AS REQUIRED BY ELECTRICAL EQUIPMENT SAFETY STANDARDS. THE DISHWASHER IS INTENDED FOR PROFESSIONAL USE ONLY AND MUST ONLY BE USED BY AUTHORISED STAFF. IT IS DESIGNED TO WASH TABLEWARE (PLATES, CUPS, BOWLS, OVEN DISHES AND CUTLERY) AND SIMILAR ITEMS IN THE RESTAURANT AND INSTITUTIONAL CATERING SECTOR, AND COMPLIES WITH THE INTERNATIONAL STANDARDS ON ELECTRICAL AND MECHANICAL SAFETY (CEI-EN-IEC 60335-2-58/61770) AND ELECTROMAGNETIC COMPATIBILITY (CEI-IEC-EN 55014-1/-2,

SMEG

°C 15°C

- 60°C

°df 15°-

60°

l 2.3

db(A)

<48

IPX

Kg 43/48

◄

HAR

► H07RN

-F

A 16

61000-3;4, 50366). THE MANUFACTURER DECLINES ALL RESPONSIBILITY FOR INJURY OR DAMAGE CAUSED BY FAILURE TO COMPLY WITH THE ABOVE REGULATIONS OR DERIVING FROM INCORRECT USE, TAMPERING WITH EVEN JUST ONE PART OF THE APPLIANCE AND THE USE OF NON-ORIGINAL SPARE PARTS.

THIS MANUAL IS AN INTEGRAL PART OF THE DISHWASHER AND MUST ALWAYS BE KEPT INTACT TOGETHER WITH THE APPLIANCE.

POSITIONING, HOOKUP, COMMISSIONING, TROUBLESHOOTING AND REPLACING THE POWER CABLE MUST BE CARRIED OUT BY QUALIFIED STAFF.

THE APPLIANCE MUST BE GROUNDED AS REQUIRED BY ELECTRICAL EQUIPMENT SAFETY STANDARDS.

THE SYMBOL OF THE RUBBISH BIN WITH A BAR ACROSS IT ON THE PRODUCT OR IN THE TECHNICAL

DOCUMENTATION INDICATES THAT THIS PRODUCT MUST NOT BE TREATED AS ORDINARY DOMESTIC WASTE BUT MUST BE CONSIGNED TO THE SPECIAL COLLECTION POINT FOR THE RECYCLING OF ELECTRICAL AND ELECTRONIC EQUIPMENT.

NEVER PLACE SOLVENTS SUCH AS ALCOHOL OR TURPENTINE, WHICH MIGHT CAUSE AN EXPLOSION, INSIDE THE APPLIANCE. NEVER LOAD DISHES DIRTY WITH ASH, WAX OR PAINTS.

NEVER USE THE DISHWASHER OR ANY PART OF IT AS A LADDER, SUPPORT OR STAND FOR PEOPLE, ANIMALS OR ANY OBJECT. LEANING OR SITTING ON THE OPEN DOOR OF THE DISHWASHER MIGHT CAUSE IT TO TIP OVER, PUTTING PEOPLE IN DANGER. NEVER LEAVE THE DISHWASHER DOOR OPEN SINCE PEOPLE MIGHT TRIP OVER IT.

DO NOT DRINK ANY WATER LEFT IN THE DISHES OR DISHWASHER AT THE END OF THE WASHING PROGRAM.

THE APPLIANCE IS NOT SUITABLE FOR USE BY JUVENILES OR PERSONS WITH REDUCED PHYSICAL, SENSORIAL OR MENTAL CAPACITIES, OR THOSE WITHOUT THE NECESSARY KNOWLEDGE AND EXPERIENCE.

SUCH PERSONS MAY ONLY USE THE APPLIANCE UNDER THE SUPERVISION OF A PERSON RESPONSIBLE FOR THEIR SAFETY.

2 TECHNICAL DATA

Water intake pressure kPa (bar) 200-600 (2 ÷ 6)

Water intake temperature

Intake water hardness (models with softener)

Rinse cycle water consumption

Boiler capacity

Tank capacity

Noise level

Degree of protection

Net weight (with and without softener)

Power supply cable type

Fuse

VOLTAGE

230V50Hz/1/N/PE

PROTECTIVE

FUSE

20A 0.8kW 0.3kW 2.8kW 3.1kW 14A 3X2.5

TANK

HEATING

ELEMENT

MOTOR BOILER

TOTAL POWER RATING

MAXIMUM

POWER

ABSORPTION

POWER

CABLE

SMEG

CAVITY DIMENSIONS FOR BUILT-UNDER INSTALLATION

APPLIANCE DIMENSIONS AND CONNECTION POSITIONS

(** N.B.: distance “1000” - max 600 if siphon with valve is used)

(*N.B.: distance “60” - with heat exchanger)

SMEG

KEY TO LETTERS USED IN DIAGRAM

LOWER BACK PANEL

EARTH TERMINAL

PERISTALTIC PUMP HOSES

ELECTRICITY SUPPLY CABLE

DRAIN HOSE

FILLER HOSE

EXTERNAL DISPENSER POWER SUPPLY CABLE ENTRY POINT

3 INSTALLATION AND POSITIONING

INSTALLATION and POSITIONING

Bring the dishwasher to the installation site, remove the packaging and check the appliance and components for damage; any

damage found must be reported to the transporter in writing. The packaging components (plastic bags, expanded polystyrene,

nails, etc.) must not be left within reach of children and pets since they are potentially dangerous. All packaging materials used

are environment-friendly. They can be kept without constituting any hazard, or may be disposed of at a specialist waste disposal

centre. The plastic components suitable for recycling are marked as follows: PE polyethylene: external packaging film, bag

containing the instructions, protective bags. PP polypropylene: straps. PS expanded polystyrene: corner guards, top of

packaging. Wooden and cardboard components can be disposed of in accordance with the relevant regulations.

When the product is decommissioned it must not be dumped in the environment; it must be disposed of in accordance with the relevant regulations. All metal parts are in stainless steel and can be removed. The plastic parts are marked with the symbol identifying the material used.

POSITIONING

Warning: the indoor system and premises in which equipment for institutions is installed must comply with

the relevant regulations.

The manufacturer declines all liability for direct or indirect injury or damage deriving from failure to comply with these regulations. Before installation, check that there are no objects or materials in the vicinity which may be damaged by steam or splashes of washing solution, or that any such items are suitably protected. Place the dishwasher in the chosen point and remove the protective film. Level the dishwasher (with the aid of a spirit level) on its adjustable feet to ensure that it is stable; all other mounting solutions must be approved by the manufacturer.

+ 15 hidden pages