PROFESSIONAL DISHWASHER
1 Precautions for safety and use
2 Technical data
3 Installation and positioning
4 INSTALLATION INSTRUCTIONS FOR THE
AFTER-SALES SERVICE
5 Start-up
6 Settings
7 Malfunctions shown on the display (for the technician)
8 INSTRUCTIONS FOR THE USER
9 Choosing the program
10 Supplementary Functions
11 Maintenance and cleaning
12 Troubleshooting
13 Malfunctions shown on the display (for the user)
You are advised to read all the instructions in this manual carefully to become familiar with the right conditions
for the proper use of your dishwasher.
TECHNICAL INSTRUCTIONS:
These are intended for the qualified staff who are to install, commission and test the
appliance and carry out any servicing and repairs.
INSTRUCTIONS FOR THE USER:
These provide recommendations for use, a description of the controls and the correct
procedures for cleaning and maintaining the dishwasher.
1 Precautions for safety and use
THIS MANUAL IS AN INTEGRAL PART OF THE DISHWASHER AND MUST ALWAYS BE
KEPT WITH THE APPLIANCE.
THE DISHWASHER IS INTENDED ONLY FOR PROFESSIONAL USE BY TRAINED STAFF. IT IS
DESIGNED TO WASH TABLEWARE (PLATES, CUPS, BOWLS, OVEN DISHES AND CUTLERY) AND
SIMILAR ITEMS IN THE RESTAURANT AND INSTITUTIONAL CATERING SECTOR, AND COMPLIES WITH
THE INTERNATIONAL STANDARDS ON ELECTRICAL AND MECHANICAL SAFETY (CEI-EN-IEC 60335-2-
58/61770) AND ELECTROMAGNETIC COMPATIBILITY
(CEI-IEC-EN 55014-1/-2, 61000-3;4, 50366).
THE MANUFACTURER DECLINES ALL RESPONSIBILITY FOR INJURY OR DAMAGE CAUSED BY
FAILURE TO COMPLY WITH THE ABOVE REGULATIONS OR DERIVING FROM INCORRECT USE,
TAMPERING WITH EVEN JUST ONE PART OF THE APPLIANCE AND THE USE OF NON-ORIGINAL
SPARE PARTS.
THIS APPLIANCE IS TAGGED UNDER EUROPEAN DIRECTIVE 2002/96/EC ON WASTE ELECTRICAL AND
ELECTRONIC EQUIPMENT (WEE).
BY MAKING SURE THAT THIS PRODUCT IS DISPOSED OF CORRECTLY THE USER HELPS TO
PREVENT POTENTIAL DETRIMENTAL EFFECTS ON HEALTH AND THE ENVIRONMENT.
THE
PRODUCT MUST NOT BE TREATED AS ORDINARY DOMESTIC WASTE BUT MUST BE CONSIGNED TO
THE SPECIAL COLLECTION POINT FOR THE RECYCLING OF ELECTRICAL AND ELECTRONIC
EQUIPMENT.
WHEN DECOMMISSIONING THE APPLIANCE COMPLY WITH THE LOCAL WASTE DISPOSAL
REGULATIONS.
FOR FURTHER INFORMATION ON THE TREATMENT, RECOVERY AND RECYCLING OF THIS
PRODUCT, CONTACT THE COMPETENT LOCAL OFFICE, THE DOMESTIC WASTE COLLECTION
SERVICE, OR THE SHOP WHERE THE PRODUCT WAS PURCHASED.
POSITIONING, CONNECTIONS, COMMISSIONING, TROUBLESHOOTING AND
REPLACEMENT OF THE POWER SUPPLY CABLE MUST BE CARRIED OUT BY SKILLED
STAFF.
THE APPLIANCE MUST BE IN COMPLIANCE WITH ELECTRICAL SYSTEM SAFETY
REGULATIONS.
SYMBOL ON THE PRODUCT OR IN THE TECHNICAL DOCUMENTATION INDICATES THAT THIS
NEVER PLACE SOLVENTS SUCH AS ALCOHOL OR TURPENTINE, WHICH MIGHT CAUSE
AN EXPLOSION, INSIDE THE APPLIANCE. NEVER LOAD DISHES DIRTY WITH ASH, WAX
OR PAINTS.
NEVER USE THE DISHWASHER OR ANY PART OF IT AS A LADDER, SUPPORT OR STAND
FOR PEOPLE, ANIMALS OR ANY OBJECT.
LEANING OR SITTING ON THE OPEN DOOR OF THE DISHWASHER MIGHT CAUSE IT TO
TIP OVER, PUTTING PEOPLE IN DANGER.
NEVER LEAVE THE DISHWASHER DOOR OPEN SINCE PEOPLE MIGHT TRIP OVER IT.
DO NOT DRINK ANY WATER LEFT IN THE DISHES OR DISHWASHER AT THE END OF THE
WASHING PROGRAM.
THE APPLIANCE IS NOT SUITABLE FOR USE BY JUVENILES OR PERSONS WITH
REDUCED PHYSICAL, SENSORIAL OR MENTAL CAPACITIES, OR THOSE WITHOUT THE
NECESSARY KNOWLEDGE AND EXPERIENCE. SUCH PERSONS MAY ONLY USE THE
APPLIANCE UNDER THE SUPERVISION OF A PERSON RESPONSIBLE FOR THEIR SAFETY.
2
2 Technical data
TECHNICAL DATA
Supply voltage V 400V 3N ~
- convertible to single-phase version V 230V -1N ~
Frequency Hz 50
Max. power absorption at 400V 3N ~ kW 6.8
Max. power absorption at 230V 1N ~ kW 2.8
Boiler heating element power at 400V 3N ~ kW 6.0
Boiler heating element power at 230V 1N ~ kW 2.0
Tank heating element power kW 0.8
Water intake pressure kPa (bar) 100-600 (1 ÷ 6)
Water intake temperature °C 15°C – 60°C
Water hardness (models with softener) °dF 15°dF-60°dF
Rinse cycle water consumption I 3.5
Boiler capacity I 7 + 1
Tank capacity I 11
Standard cycle duration with intake water at 50°C s 90/150/240/variable
Noise level dB(A)
Degree of protection IPX 4
Net weight kg
Power supply cable type ◄HAR► H07RN-F
Fuse A 4
400V 3N ~ 230V 1N ~
C S C S
2,8 kW --- --- 3x2,5
6,8 kW
5x2,5 16A 3P+N
--- ---
16A 1P+N
C = Power Supply Cable. S = Master Switch
3
LOWER BACK PANEL
R
FILLER HOSE
C
Q
EARTH TERMINAL
ELECTRICITY SUPPLY CABLE
E
PERISTALTIC HOSES
P
DRAIN HOSE
S
EXTERNAL DISPENSER POWER
T
SUPPLY CABLE ENTRY POINT
TERMINAL BOARD
M
3 Installation and positioning
INSTALLATION and POSITIONING
Bring the dishwasher to the installation site, remove the packaging and check the appliance and components
for damage; any damage found must be reported to the transporter in writing.
The packaging components (plastic bags, expanded polystyrene, nails, etc.) must not be left within reach of
children and pets since they are potentially dangerous.
All packaging materials used are environment-friendly. They can be kept without constituting any hazard, or
may be disposed of at a specialist waste disposal centre.
The plastic components suitable for recycling are marked as follows:
PE polyethylene: external packaging film, bag containing the instructions, protective bags.
PP polypropylene: straps.
PS expanded polystyrene: corner guards, top of packaging.
Wooden and cardboard components can be disposed of in accordance with the relevant regulations.
When the product is decommissioned it must not be dumped in the environment; it must be disposed of in
accordance with the relevant regulations. All metal parts are in stainless steel and can be removed.
The plastic parts are marked with the symbol identifying the material used.
Models with aquastop
The aquastop device prevents flooding in the event of water leaks. In these models,
the water intake hose is fitted with a solenoid valve. Do not cut the hose and do not
drop the solenoid valve into water. In the event of damage to the water intake hose,
disconnect the appliance from the electricity supply.
POSITIONING:
Caution: the indoor system and premises in which equipment for institutions is installed must
comply with the relevant regulations.
The manufacturer declines all liability for direct or indirect injury or damage deriving from failure to comply
with these regulations.
Before installation, check that there are no objects or materials in the vicinity which may be damaged by
steam or splashes of washing solution, or that any such items are suitably protected.
Place the dishwasher in the chosen point and remove the protective film.
Level the dishwasher (with the aid of a spirit level) on its adjustable feet to ensure that it is stable; all other
mounting solutions must be approved by the manufacturer.
4
4 INSTALLATION INSTRUCTIONS FOR THE AFTER-SALES SERVICE
Water supply and drain connection:
The water pipelines and electricity supply cable lead out of the bottom right-hand
corner of the appliance. Connect the water intake hose to a connector with ¾” gas
threaded fitting, fitting the filter A provided (in models with aquastop, the filter and ring-
nut form a single unit).
The connection to the water mains must only be made with new hoses; the use of old
or worn hoses is not permitted.
The dynamic intake pressure must be between 1 and 6 bar; if it is higher, installation of a pressure reducer is
recommended.
It is essential to fit a main stop tap on the water intake pipeline; the tap must be accessible after installation of
the appliance, so do not install it behind the dishwasher.
The stated cycle duration refers to appliances supplied with hot water at 50°C.
If the appliance is supplied with cold water, the cycle duration might increase depending on the intake water
temperature, since the dishwasher is fitted with the HTR system, which requires set temperature and pressure
for rinsing.
Drainage:
The dishwasher is fitted with a drain pump and can operate with drain
connections on the floor or wall.
4.1 Water connection
If the drain connection is to an outlet with valve, the maximum height of the drain is reduced to 600 mm.
In all cases, after installation check that the drain is fully functional by pumping out the tank completely (P0
cycle).
Caution:
constricted or crushed after installation.
make sure that the intake and drain hoses are not bent,
5
4.1 Electrical connection
The dishwasher and any additional equipment must be connected to the electrical system by
authorised, skilled staff, in accordance with the relevant regulations; also comply with the technical
instructions for the connection.
The total rated power is stated on the appliance’s technical data plate.
The electrical protection devices fitted for the dishwasher must serve this appliance only.
The user must have a master switch and a differential safety breaker, with rating suitable for the
machine’s characteristics, installed on the electricity supply line in accordance with the relevant
regulations.
These switches must be installed close to the dishwasher, be easily accessible after installation, and
provide complete disconnection from the electrical mains in overvoltage class III conditions.
Warning !!!
The dishwasher is always powered up unless the master switch is turned off.
Connect the appliance to the user’s earth system. The terminal for the connection is in the bottom
‐
right-hand corner of the appliance.
‐ The earth wire (PE) is yellow-green in colour, the neutral wire (N) is blue and the live wires (L1, L2,
L3) are black, grey and brown.
In the event of single-phase connection (230V-1N~) the connection to the electrical mains must be made
using a cable with plug compliant with the relevant regulations..
IN THE EVENT OF DAMAGE TO THE SUPPLY CORD, HAVE IT REPLACED BY THE MANUFACTURER
OR AN AUTHORIZED TECHNICAL SERVICE CENTRE IN ORDER TO AVOID ANY RISK.
6
5 START-UP
FIRST START-UP
The electrical protection system must undergo a functional test before the appliance is put into operation.
The appliance must be installed and/or inspected by the qualified staff, who will start it up for the first time and
provide the relevant operating instructions.
PREPARING FOR USE
Important:
The rinse aid dispenser is fitted on all models, the detergent dispenser only on some.
If both dispensers are present put the external detergent and rinse aid containers in
place and insert the respective intake hoses on the rear of the machine into them.
Red hose: detergent
blue hose: rinse aid
Before inserting the hoses into the containers, fit the weights (needed to ensure that
they always draw in liquid from the bottoms of the containers) and the filters onto their
ends as shown.
If the detergent dispenser is not factory-fitted, it can be by ordering the relative kit.
As an alternative an external dispenser can be fitted, making the electrical connection by means of an H05 RNF 2x0.5 mm electrical cable, which can be laid along the route shown in the TECHNICAL DATA diagram and
connected as shown in the wiring diagram supplied with the dishwasher.
The dispenser must operate on 230V/50 Hz with maximum power absorption of 15 W.
Connect to the detergent dispenser outside the dishwasher using the red hose mentioned above.
Whenever the type of detergent or rinse aid is changed, it is ABSOLUTELY ESSENTIAL to flush out the
peristaltic pumps by placing the external intake pipes in water for a few cycles.
Always use only products specifically recommended for use in a dishwasher.
The internal pipes of the detergent and rinse paid pumps should be replaced by the After-Sales Service
every 12 months or 15,000 wash cycles.
Failure to comply with this recommendation leads to forfeiture of the warranty entitlement on the
appliance’s water system.
IMPORTANT:
6 SETTINGS
SETTINGS
During start-up, the functions/parameters listed below must be set or adjusted:
On first installation, a series of operations can be performed to allow the dishwasher to be customised to the user’s
needs. A short testing cycle can also be performed to verify operation of all the components. To perform these
operations, access “programming mode” as explained below
7
6.1 Dishwasher parameter modification procedure:
(ONLY ACCESSIBLE AFTER FILLING IS COMPLETE or WITH THE DOOR OPEN)
Indicator lights as follows: off; green; orange; flashing.
Access “programming mode” by pressing the
seconds (UnLo 1:58 will appear on the display) with the appliance on (after the
filling and heating phase); at the “beep", release the button and press it
again quickly within 0.5 seconds. Keep pressing the button again to scroll
through all the modifiable parameters in the following order:
Rinse aid delivery amount
on/off button for a few
Detergent delivery amount
Rinsing temperature
Washing temperature
Start-on/start-off.
Set at “on” to start the cycle when the door is closed.
Set at “off” for cycle start after confirmation with the start button
Regeneration frequency, depending on water hardness (if softener is installed)
tStP on/off
“on” = minimum rinsing temperature as set, regardless of intake water
temperature; the cycle duration may be a few seconds longer than the nominal
length.
“off” = the minimum rinsing temperature might be a few degrees lower than
the setting if hot intake water is not used.
Rinse aid pump operating minutes display.
Detergent pump operating minutes display.
8
Energy consumption (kW) display
The Pc option indicates the total kW consumed since installation of the
dishwasher or since the latest reset.
Customisation of duration of program P4.
N.B.: the machine must be set on “P4”, see “6.7 Setting program P4
duration”.
Displaying the cycle count
When scrolling through the appliance parameters the item
count of the cycles the dishwasher has performed since installation, will be
found.
This parameter cannot be modified or reset unless the software is
reprogrammed.
“tc 88888” , the total
SETTING THE MODEL (for After-Sales Service only)
In the event of replacement of the circuit board (used on several models)
scroll through to the last modifiable parameter option to select the
appropriate model, “PRF400” or “PRF500”. This operation must be
carried out with the tank empty and door open.
Indicator lights as follows:
off; green; orange; flashing.
6.1.1 Setting up rinse aid delivery
Modify the value of the parameter
by pressing .
* default value (factory preset)
6.1.2 Setting up detergent delivery
Modify the value of the parameter
by pressing .
* default value (factory preset)
RINSE AID
Delivery time
(s)
0 0,0
6 0,7
12 1,3
18 2,0
24 2,7
30 * 3,3
26 4,0
48 5.3
DETERGENT
Delivery time
(s)
0 0,0
4 1,7
8 3,3
12 * 5,0
16 6,7
Delivery
quantity (c.c.)
Delivery
quantity (c.c.)
9
20 8,3
24 10,0
6.1.3 Rinsing temperature setup
Modify the value of the parameter by pressing
6.1.4 Washing temperature setup
Modify the value of the parameter by pressing .
Indicator lights as follows: off; green; orange; flashing.
6.1.5 Autostart function
Modify the parameter (ON/OFF) by pressing
(Default value: 85°C)
Min. 71°C – max. 85°C
(Default value: 62 °C)
Min. 52°C – max. 62°C
.
.
Set at “on” to start the cycle when the door is closed.
Set at “off” for cycle start after confirmation with the start button
6.1.6 Regeneration frequency setup (models with softener)
• Default value: H00; modify the parameter to suit the mains water hardness.
• Generally H03 will be satisfactory for most users.
• At first use, the salt tank has to be filled. It is subsequently sufficient simply to fill up with regenerating salt
when necessary.
Modify the value
of the parameter
by pressing .
Regeneration cycle duration: 12 minutes 33,5 60 H06
With values over 60°dF an external water treatment device must be used and the regeneration frequency must be
set on H00.
Hardness
(°dH german
degrees)
Regeneration off Regeneration off H00
8,5 15 H01
11 20 H02
17 30 H03
22,5 40 H04
28 50 H05
Hardness
(°dF French
degrees)
Setting level
10
6.1.7 tStP (minimum rinsing temperature) function
Modify the parameter (ON/OFF) by pressing .
Set at “on” for minimum rinsing temperature as set.
Set as “off” to accept minimum rinsing temperature a few degrees lower than the setting if hot intake water is not
used.
6.1.8 Rinse aid pump
To reset, press
for 3 seconds.
Display (also reset when needed)
6.1.9 Detergent pump
To reset, press for 3 seconds.
Display (also reset when needed)
6.1.10 Energy consumption – Display and reset
To reset, press
for 3 seconds.
6.1.11 Customisation of duration of program P4
The duration of program P4 can be customised from 5 to 20 minutes using the appliance parameter modification
procedure, but the dishwasher must be set on program P4.
After setting program P4 access the programming
procedure and scroll through to “ınF” (last parameter to
appear) then press the
of the cycle (from 5 to 20 minutes)
After a few seconds without the user pressing any
buttons, the display will return to the normal operating
status and the modifications will be saved.
button to modify the duration
11
6.1.12 Setting the Model (for After-Sales Service only)
Modify by pressing .
6.2 Starting the peristaltic pumps – rapid filling of detergent and rinse aid delivery
circuit.
Perform after the parameter modification procedure explained in the previous point.
Indicator lights as follows: off; green; orange; flashing.
With the dishwasher powered up, access “programming mode” by pressing the
on/off button for a few seconds; at the “beep”, release the button and press it
again quickly within 0.5 seconds.
The peristaltic pumps continue to operate until the same buttons are pressed
again. The rinse aid and detergent symbol lights remain on as long as work is
in progress; bear in mind that the rinse aid peristaltic pump fills the circuit in
about 7 minutes, while for the detergent it only takes 2 minutes.
12
7 MALFUNCTIONS SHOWN ON THE DISPLAY
The dishwasher is able to identify a number of malfunctions and show them on the display.
If the problem persists after the dishwasher has been switched off and back on, proceed as described below:
Err01
The anti-flooding system has been activated
(for the relevant models only).
Large water leak : check the origin of the problem.
Err04
Err05
Err06
Err09
Err23
Tank temperature probe malfunction
Tank water filling malfunction
Water pump-out malfunction
Tank water level too high
Boiler heating malfunction (does not heat
up)
Tank temperature probe disconnected or not working
Check dynamic pressure in intake system, inspect water
intake filter and clean if necessary.
If the problem persists:
- tank pressure switch has failed (continuous empty
reading)
- leak from pipe connected to air trap
- valve vent exhaust pipe blocked
Inspect the filters for dirt and that the drain hose is not
blocked, bent or crushed.
Check that the drain pump is not blocked by dirt by
removing the insert on the sump (from inside the tank)
If the problem persists:
‐ with the tank empty: tank pressure switch defect
(the contact is locked on full)
‐
with tank full: drain pump has failed
- with tank full:
see above (water pump-out malfunction)
- with tank empty:
safety pressure defect (the contact
is locked on full)
-circuit board relay failure,
- contactor failure.
- boiler safety thermostat failure,
- boiler temperature probe faulty or incorrectly positioned
- water continues to enter the tank due to tank pressure
switch defect
Err24
Err25
Err26
Err27
Err28
Boiler temperature probe malfunction boiler temperature probe disconnected or not working
Check that the water intake tap is on and the dynamic
pressure in the intake system, inspect the water intake
Boiler water filling malfunction
filter and clean if necessary.
If the problem persists:
- boiler pressure switch has failed (continuous empty
reading)
- pipe leaking/disconnected
- check that rinsing spray arm nozzles are clean
Boiler emptying malfunction
- boiler pressure switch has failed (continuous full reading)
- rinsing pump not working
Boiler emptying malfunction – with tank full Boiler pressure switch has failed (continuous full reading)
Boiler heating malfunction (overheating)
-circuit board relay failure, or
- contactor failure
13
8.1 Control panel
8 INSTRUCTIONS FOR THE USER
On-off button
Program selection button
Start CONFIRM/PAUSE button
Total emptying button (tank and boiler)
Additional function selection button
L1 Main power on light
L2 Intake/standby cycle in progress light (orange/green)
L3 Pump-out in progress light
No rinse-aid symbol (if a system for monitoring outside the dishwasher is provided)
Tank heating element on symbol
No salt symbol (if softener is fitted)
Boiler element on symbol
No detergent symbol (if a system for monitoring outside the dishwasher is provided)
14
8.2 Before washing
Use only detergents and rinse aids for industrial dishwashers.
Do not use detergents intended for hand washing.
We recommend the use of Smeg products, specially developed for this dishwasher.
When topping up the tanks, take care not to swap the products; this might damage the dishwasher and
cause malfunctions.
Do not mix different detergents; this would damage the dispenser device.
Industrial dishwasher detergents may cause serious irritations. Comply carefully with the instructions provided by
the detergent producer on the pack.
mains water
tap (user)
The level of
detergent and
rinse aid in the
containers.
That there is
regenerating salt
in the relative
container (if
fitted).
Check:
Turn on the
That the filters are in place,
the spray arms rotate, and
there are no foreign bodies in
the dishwasher.
Switch on the master
switch (user): the
word “OFF” appears
on the display.
8.3 FIRST USE EACH DAY (tank and boiler empty)
Indicator lights as follows: off; green; orange; flashing.
Display shows
Actions and what happens
With the door closed:
Press
the dishwasher fills the tank after the water in the boiler
has heated up; light L2 shows orange and the boiler
heating element symbol
Wait for P1 to appear and LED L1 to change from
orange to green;
the tank heating element comes on until the set
temperature is reached. The duration of this stage may
vary depending on the mains water temperature and on
the single-phase connection.
Press the button to display the tank (left) and boiler
(right) temperatures.
Load the dishes
and hold it down
appears on the display.
Select the program required by pressing .
Confirm the program start by pressing and holding it
down for 1 second (light L2 changes from green to
orange).
15
Cycle in progress, the time left until the end of the cycle
is displayed. If the door is opened “CLOSE” flashes and
the program stops; when it is closed again the program
restarts from the beginning.
At the end of the program “End” flashes
Unload the dishes
When the door is closed again, the last program is repeated.
8.4 Program change
With the door closed, to change to a fresh program
instead of repeating the last one, press the
The programs available are displayed (light L2 changes
from orange to green).
If a program has already started, hold down to
interrupt it.
change the program by pressing .
Confirm the program start by pressing and holding it
down for 1 second (light L2 changes back to orange).
button.
N.B.:
During heating of the water in the boiler, the tank heating element
may appear on the display.
Filter presence sensor (on some models only)
The filter is fitted with a sensor which checks that it is properly fitted; if it is not in the correct position, the word
“FiLter” appears on the display.
and boiler heating element symbols
16
9 CHOOSING THE PROGRAM
PROGRAM
(*)
The cycle duration stated above refers to three-phase appliances supplied with hot water at 50°C.
If the appliance is supplied with cold water, the cycle duration might increase depending on the intake
water temperature, since the dishwasher is fitted with the HTR system, which requires set temperature and
pressure for rinsing.
TYPE OF DIRT DURATION (*)
P1
P2
P3
P4
Glasses Short, about 1’ 30”
1’ with glassware function active.
Glasses, cups and plates with light dirt Average, about 2’ 30”
2’ with glassware function active.
Very dirty dishes and cutlery Long, about 4’
5’30” with sani function active.
Depending on the duration set. As required from 5 to 20'.
10 SUPPLEMENTARY FUNCTIONS
Indicator lights as follows: off; green; orange; flashing.
To select a supplementary function, when the program required is shown on the display (P1, P2, P3 or P4)
press the
button. Only one supplementary function can be selected for each program.
10.1 Selecting the “glassware” function (available in P1-P2)
Reduces the program’s rinsing temperature and duration
Select the program required
(7.4 OPERATION)
Hold
down to select the glassware function then
to confirm the program start.
10.2 Selecting the “extra rinse” function (available in P1-P2-P3-P4)
Extends the duration of the rinse
Hold
Select the program required
(7.4 OPERATION)
down to select the extra rinse function then
to confirm the program start.
17
10.3 Selecting the “sanitisation” function (only available in P3)
Increases the washing and rinsing temperature and the program duration
Select the program required
(7.4 OPERATION)
Press
to select the sanitisation function then to
confirm the program start.
N.B.:
‐ the supplementary function remains selected until the program is changed or the dishwasher is switched off
by pressing the
button.
‐ During the selected program, the display alternates between showing the supplementary function and the
duration.
LOADING THE DISHES
Plates
The basket is able to take
12 soup plates or 18 dinner plates.
Remove solid residues (bones, fruit
peel, stones, etc.) and soak plates with
dried residues of cheese, egg, etc. in
water before loading in the dishwasher.
Glasses: Load glasses upside down.
Cutlery: Use the special basket(s). Load cutlery loose, preferably with the handle at the bottom, taking care not to
injure yourself with fork prongs or knife blades.
TOTAL PUMP-OUT AT THE END OF THE DAY
The dishwasher is able to perform an automatic cleaning cycle at the end of the day.
Press the
button; “UnLo” and the duration appear
on the display.
Confirm by pressing ; light L2 turns orange.
After a total pump-out the filters should be cleaned as described above.
Never switch the dishwasher off with water in the tank; pump out firs t.
At the end of the pump-out, the appliance sets in
“OFF” status.
18
TOTAL PUMP-OUT AT THE END OF THE DAY + Resin regeneration
(form models with water softener)
From time to time, on models with water softener, before the total pump-out at the end of the day the user will
automatically be reminded to carry out the resin regeneration cycle, required after a number of washes which
depends on the hardness of the water (about 30 for average setting H03). In this case the sequence will be as
follows:
Press the pump-out button
duration appear on the display.
; “rEgE” and the
Confirm by pressing ; light L2 turns orange.
At the end of the pump-out, the appliance sets in
“OFF” status.
Topping up with regenerating salt (for models with water softener)
Salt must be added when the “no salt” light (
) appears on the display.
Top up with salt when there is no water in the tank to prevent washing water from getting into the water softener
device.
Caution: use only salt of the specific type, do not use cooking salt.
The salt tank has a capacity of about 1 kg of coarse-grained salt.
The salt reservoir is in the bottom of the tank. After removing the basket, undo the cap and pour the salt in using
the funnel supplied. Remove any salt residues around the opening before screwing the cap back on.
11 MAINTENANCE AND CLEANING
Although no particular scheduled maintenance is required, users are advised to have the dishwasher checked by a
specialist technician twice a year.
N.B.: the manufacturer accepts no liability for wilful damage or damage deriving from carelessness, neglect, failure
to comply with instructions, regulations and standards or incorrect connections.
11.1 Daily cleaning
The dishwasher has IPX4 protection, but the use of direct water jets for cleaning is forbidden.
Cleaning the filter during the day
In case of particularly heavy-duty working conditions, the filter should be cleaned every 30-40 cycles, keeping the
machine in operating conditions; to do this, carry out the “partial tank pump-out” routine (program “P0”).
Press the
Confirm by pressing ; light L2 turns orange.
At the end of the pump-out the word “End” flashes on
the display. The display returns to showing “P1”. Close
the door again to start filling the tank prior to
19
button, and hold it down, until “P0” and
the duration of 1’ appear on the display.
performance of a new wash cycle.
Remove the filters (simply lift them out as shown here), taking care that no
large residues fall into the sump underneath. Clean them to remove residues
and rinse with plenty of water, then put them correctly back in place; do not
use sharp or pointed tools.
Clean away any limescale deposits to prevent excessive build-ups;
‐ If possible, leave the door ajar when not in use;
‐ Clean surfaces thoroughly and often with a damp cloth; use neutral,
non-abrasive detergents which do not use chlorine compounds, which
corrode and damage stainless steel.
Do not use the products mentioned above even when cleaning the floor underneath or in the vicinity of the
dishwasher, to ensure that fumes or drops cannot damage the steel surfaces.
IMPORTANT: The dishwasher automatically performs program “P0” at the start of the day if w ater has been
left in the tank and has dropped below the temperature of 40°C
11.2 Periodic checks
Remove the top and bottom spray arms by unscrewing the central screw and unscrew the caps from the ends of
the rinsing arms as shown. Do not unscrew the nozzles.
Clean the holes and nozzles under a jet of clean running water; do not use tools which might cause damage.
Reassemble the spray arms with care.
Clean the outside of the appliance with a damp cloth and neutral soap, rinsing and drying thoroughly.
11.3 Lengthy periods out of use
If the dishwasher is to be out of use for a fairly long period of time, the detergent and rinse aid dispenser
devices must be emptied to prevent crystallisation and damage to the pumps: Remove the intake hoses
from the detergent and rinse aid containers and place them in a container of clean water, then perform a few wash
cycles followed by a complete pump-out.
Finally, turn off the master switch, close the water intake valve and leave the door ajar until the interior is
completely dry. The detergent and rinse aid intake hoses must be put back into the containers when the
dishwasher is returned to service, taking care not to swap them over (red hose = detergent, blue hose = rinse
aid).
20
12 TROUBLESHOOTING
If the system fails to pump out because the drain pump is fouled (as
a result of incorrect filter positioning), proceed as follows:
Bale out the dishwasher with a basin and disconnect it from the
electrical mains.
Unscrew the screw A, release the tang B and lift it.
Check that the impeller of the drain pump underneath the cover
turns freely, and is free from dirt, limescale residues, or pieces of
glass. Never use tools, screwdrivers, scissors, etc.
PROBLEM
POSSIBLE CAUSE
POSSIBLE REMEDY
LIGHT S1 DOES NOT COME ON Mains power failure Check electrical mains connection.
WASHING PROGRAM DOES
NOT START
The dishwasher has not yet
finished filling.
The word CLOSE remains on the
display
Spray arm washing holes blocked
by dirt or limescale
Wait for the word FILL to go out.
If the word CLOSE remains on the
display even with the door closed, call
the after-sales service.
Remove spray arms and clean them
(10.2 Periodic checks)
Filter fouled See “Cleaning the filter during the day”
Too little or unsuitable detergent
or rinse aid
Check type and quantity of detergent.
Check that the detergent intake pipe
Detergent intake blocked
underneath the filter is unobstructed (T
in photo).
POOR WASHING RESULTS
No or not enough detergent or
rinse aid being supplied: detergent
or rinse aid not being taken from
the relative container.
Pipe inside detergent and/or rinse aid
peristaltic pump worn or broke, have it
replaced by the After-Sales Service.
INADEQUATE RINSING
STAINS ON GLASSES AND
CUTLERY
Plates/glasses badly arranged Arrange plates/glasses correctly.
Check temperature shown on the
Low washing temperature
display, call the after-sales service if
less than 50°
Increase washing duration, especially
Inappropriate cycle set
Spray arm nozzles fouled
Limescale in boiler
Rinse aid unsuitable or not being
delivered correctly.
Water hardness above 12°dF or
large amounts of dissolved salts
if dishes are very dirty or dirt has dried
on.
Check that nozzles are clean, and
ensure that the softener is working
properly (if installed).
Check container of rinse aid and
whether type is suitable for the mains
water- If the problem persists, contact
the after-sales service.
21
Check that the dishwasher drain hose
WATER IN TANK AFTER PUMP-
OUT
Drain hose incorrectly positioned
or partially obstructed.
and rain are unobstructed and the
drain is not too high up; see
connection diagram.
13 MALFUNCTIONS SHOWN ON THE DISPLAY
The dishwasher is able to identify a number of malfunctions and show them on the display.
If the problem persists after the dishwasher has been switched off and back on, proceed as described below:
Err01
The anti-flooding system has been activated
(for the relevant models only).
Contact the After-Sales Service.
Err04
Err05
Err06
Err09
Err23
Err24
Err25
Tank temperature probe malfunction
Tank water filling malfunction
Water pump-out malfunction
(dishwasher is left full of water)
Tank water level too high
Boiler heating malfunction (does not heat
up)
Boiler temperature probe malfunction
Boiler water filling malfunction
Contact the After-Sales Service
Check that the water intake tap is on and the dynamic
pressure in the intake system, inspect the water intake
filter and clean if necessary. If the problem persists,
contact the After-Sales Service.
Inspect the filters for dirt and check that the drain hose is
not blocked, bent or crushed.
Check that the drain pump is not blocked by dirt; proceed
as described in point “10.2 Periodic checks”.
If the problem persists, contact the After-Sales Service.
Contact the After-Sales Service.
Check that the water intake tap is on and the dynamic
pressure in intake system, inspect water intake filter and
clean if necessary. If the problem persists, contact the
After-Sales Service.
Err26
Err27
Err28
Boiler emptying malfunction
Boiler emptying malfunction – with tank full
Boiler heating malfunction (overheating)
Check that the rinsing spray arm nozzles are not fouled
If the problem persists, contact the After-Sales Service.
Contact the After-Sales Service.
22
Loading...