Smeg ALFA341XM User Manual

Contents

1. INSTRUCTIONS FOR SAFETY AND USE ....................... 22

2. OVEN INSTALLATION...................................................... 25

3. DESCRIPTION OF CONTROLS ....................................... 29

4. USING THE OVEN............................................................ 31

5. CLEANING AND MAINTENANCE .................................... 34

6. EXTRAORDINARY MAINTENANCE ................................ 37

INSTRUCTIONS FOR THE USER: these contain user advice, description
of the commands and the correct procedures for cleaning and maintenance
of the appliance.

INSTRUCTIONS FOR THE INSTALLER: these instructions are intended
for the qualified technician who must perform the installation, put it into
operation and test the appliance.

21

Instructions for safety and use

1. INSTRUCTIONS FOR SAFETY AND USE

THIS MANUAL IS AN INTEGRAL PART OF THE APPLIANCE. IT MUST BE
KEPT IN ITS ENTIRETY AND IN AN ACCESSIBLE PLACE FOR THE WHOLE
WORKING LIFE OF THE OVEN. WE URGE YOU TO READ THIS MANUAL AND
ALL THE INFORMATION IT CONTAINS CAREFULLY BEFORE USING THE
OVEN. INSTALLATION MUST BE CARRIED OUT BY QUALIFIED PERSONNEL
IN ACCORDANCE WITH THE REGULATIONS IN FORCE. THIS OVEN IS
INTENDED FOR PROFESSIONAL USE AND CONFORMS TO THE EEC
DIRECTIVES CURRENTLY IN FORCE. THE APPLIANCE HAS BEEN BUILT TO
CARRY OUT THE FOLLOWING FUNCTIONS: COOKING AND HEATING-UP OF

FOOD; ALL OTHER USES ARE CONSIDERED IMPROPER.
THE MANUFACTURER DECLINES ALL RESPONSIBILITY FOR IMPROPER
USE.

DO NOT DISCARD PACKING IN THE HOME ENVIRONMENT. SEPARATE THE
VARIOUS WASTE MATERIALS AND TAKE THEM TO THE NEAREST SPECIAL
GARBAGE COLLECTION CENTRE.

THE APPLIANCE MUST BE CONNECTED TO EARTH IN COMPLIANCE WITH
ELECTRICAL SYSTEM SAFETY REGULATIONS.

WHEN LINKING UP TO MAINS BY PLUG AND SOCKET, MAKE SURE THAT
BOTH ARE COMPATIBLE AND CONNECT BY MEANS OF A POWER CABLE
COMPLYING WITH APPLICABLE REGULATIONS.
NEVER UNPLUG BY PULLING ON THE CABLE.

22

DO NOT OBSTRUCT VENTILATION OR HEAT DISPERSAL OPENINGS.

IMMEDIATELY AFTER INSTALLATION CARRY OUT A BRIEF INSPECTION
TEST OF THE OVEN, FOLLOWING THE INSTRUCTIONS BELOW. SHOULD
THE APPLIANCE NOT FUNCTION, DISCONNECT IT FROM THE POWER
SUPPLY AND CALL THE NEAREST TECHNICAL ASSISTANCE CENTRE.
NEVER ATTEMPT TO REPAIR THE APPLIANCE.

NEVER PUT INFLAMMABLE OBJECTS IN THE OVEN: IF IT SHOULD
ACCIDENTALLY BE SWITCHED ON, THIS MIGHT CAUSE A FIRE.

THE APPLIANCE BECOMES VERY HOT DURING USE. SUITABLE HEAT­PROOF GLOVES SHOULD BE WORN FOR ALL OPERATIONS.

Instructions for safety and use

THE ID PLATE WITH TECHNICAL DATA, SERIAL NUMBER AND BRAND NAME
IS POSITIONED VISIBLY ON THE SIDE OF THE OVEN.
DO NOT REMOVE THIS PLATE FOR ANY REASON.

THE APPLIANCE IS DESIGNED FOR PROFESSIONAL USE BY TRAINED
PERSONS. DO NOT ALLOW CHILDREN TO GO NEAR IT OR PLAY WITH IT.

TRAYS MUST BE WASHED BEFORE USE WITH A SUITABLE KITCHENWARE
DETERGENT (DO NOT USE ABRASIVE PRODUCTS).

THE HARDNESS OF THE WATER TO BE USED FOR STEAMING MUST NOT
EXCEED 10-11°F. USE TAP WATER THAT HAS BEEN TREATED WITH A
WATER PURIFICATION OR SOFTENING SYSTEM.

THE USE OF THIS APPLIANCE IS NOT PERMITTED TO PEOPLE (INCLUDING
CHILDREN) OF REDUCED PHYSICAL AND MENTAL ABILITY, OR LACKING IN
EXPERIENCE IN THE USE OF ELECTRICAL APPLIANCES.

THE OVEN IS DESIGNED FOR A MAXIMUM LOAD OF 25 KG.

BEFORE THE APPLIANCE IS PUT INTO OPERATION, ALL LABELS AND
PROTECTIVE FILMS APPLIED INSIDE OR OUTSIDE MUST BE REMOVED.

The manufacturer declines all responsibility for damage to persons or
things caused by the non-observance of the above prescriptions or
deriving from tampering with any part of the appliance or by the use of
non-original spares.

23

Instructions for safety and use

THIS APPLIANCE IS MARKED ACCORDING TO THE EUROPEAN DIRECTIVE
2002/96/EC ON WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT –
(WEEE).
THIS GUIDELINE IS THE FRAME OF A EUROPEAN-WIDE VALIDITY OF
RETURN AND RECYCLING ON WASTE ELECTRICAL AND ELECTRONIC
EQUIPMENT.

INFORMATION FOR USERS

PURSUANT TO DIRECTIVES 2002/95/EC, 2002/96/EC AND 2003/108/EC
RELATING TO THE REDUCTION OF THE USE OF HAZARDOUS
SUBSTANCES IN ELECTRICAL AND ELECTRONIC APPLIANCES, AS WELL
AS TO THE DISPOSAL OF REFUSE. THE CROSSED OUT BIN SYMBOL ON
THE APPLIANCE INDICATES THAT THE PRODUCT, AT THE END OF ITS
USEFUL LIFE, MUST BE COLLECTED SEPARATELY FROM OTHER REFUSE.
THEREFORE, THE USER MUST CONSIGN THE PRODUCT THAT HAS
REACHED THE END OF ITS WORKING LIFE TO THE APPROPRIATE
SELECTIVE COLLECTION CENTRES FOR ELECTRICAL AND ELECTRONIC
REFUSE, OR DELIVER IT BACK TO THE RETAILER WHEN PURCHASING AN
EQUIVALENT PRODUCT, ON A ONE FOR ONE BASIS. ADEQUATE
SELECTIVE COLLECTION FOR THE SUBSEQUENT FORWARDING OF THE
DECOMMISSIONED PRODUCT TO RECYCLING, TREATMENT AND
ECOLOGICALLY COMPATIBLE DISPOSAL CONTRIBUTES TO AVOIDING
POSSIBLE NEGATIVE EFFECTS ON THE ENVIRONMENT AND ON HEALTH
AND PROMOTES THE RECYCLING OF THE MATERIALS OF WHICH THE
APPLIANCE CONSISTS. THE ILLICIT DISPOSAL OF THE PRODUCT BY THE
USER RESULTS IN THE APPLICATION OF ADMINISTRATIVE SANCTIONS.

24

Instructions for the installer

2. OVEN INSTALLATION

The oven must be installed on a free-standing horizontal work top. The
distance from the rear wall must allow easy access to the terminal board
for connection of the power supply cable. Installation must be carried out
by a qualified technician and in compliance with EEC DIRECTIVES
currently in force.

2.1 Electrical connection

Make sure the voltage and the cross-section of the power cord match the
specifications indicated on the identification plate positioned on the side
of the oven. Do not remove this plate for any reason.

ALFA241

For operation on 380-415V 3N~: use an

H07RN-F type five-core cable (5 x 1.5 mm

ALFA341

For operation on 380-415V 3N~: use an

H07RN-F type five-core cable (5 x 4 mm

2

).

2

).

When linking up to mains by plug and socket, the connection must be
completed with a plug of adequate capacity. The plug and wall-mounted
socket must be of the same type (in accordance with CEI regulations).
Make sure that the supply line is suitably earthed. Avoid use of adapters
and shunts.

If the appliance is connected to the electrical mains supply in a
permanent manner, install a multipolar cut-out device on the line, with
contact opening distance equal to or greater than 3 mm located near the
appliance and in an easily reachable position.

25

Instructions for the installer

WARNING: if the phase voltage drops below 190 VAC, the performance
of the oven may suffer, not due to the product itself.

The power socket located in the rear part of the oven must be used only
to supply the extraction hood. The hood is provided as an optional
accessory and has a maximum absorbed power of 300W.

The terminal marked with this symbol connects parts together that are
normally at zero potential. Connect the appliances appropriately using
this terminal in order to make sure that they are equipotential.

2.1.1 How to reach the terminal board

26

1 Unscrew the fixing screws at the back of the side casing. 2 Slide the side casing as shown in the figure.