SMC Networks SMCSD10-Z User Manual

Copyright ©2013 SMC Networks Page 1

All Rights Reserved

I/M SMCSD10-Z rev. 1.0
6/18/13

1 Product Introduction

The SMCSD10-Z works with the Touchscreen. The
device has an optical sensor capable of detecting
smoke particles in the event of fire. It also has
an integrated heat sensor that is triggered if a
room experiences a sharp rise in temperature.
The SMCSD10-Z does not contain an alarm.
Audible alerts sound at the Touchscreen.

The SMCSD10-Z meets FPA 72 field-sensitivity
testing requirements without the need for
external meters. Built-in drift compensation
allows the SMCSD10-Z to adjust sensitivity
automatically as it becomes dirty over time. The
drift-compensation feature dramatically
increases the time between cleanings, as well as
reducing the chance of a nuisance alarm.

2 Parts List

Your SMCSD10-Z package includes:

 (1) SMCSD10-Z Smoke Detector
 (2) CR123A lithium batteries
 (1) Mounting plate
 (1) Mounting screws and anchors
 (1) This User Guide

3 Tools Required

 Flat-Tipped Screw Driver

4 Finding a Suitable Location

Review this section to ensure you get the most
out of the SMCSD10-Z. This information is in
accordance with NFPA 72 depending on country
of installation.

Pre-installation Considerations

Install the SMCSD10-Z in accordance with the
National Fire Protection Association’s (NFPA)
Standard 72, Chapters 2 and 8. Depending on the
application, you may need to reference other
chapters of NFPA 72 or NFPA 101.

Choosing an Installation Location

When choosing an installation location, consider:

 Use of structure and type of construction
 Contents you want to protect and their

burning characteristics

 Human occupancy
 Total area to be monitored
 Ceiling height and surface condition
 Air movement and vent locations
 Obstructions
 Deflections

Recommended Locations

After considering these factors, choose a
location:

 Where the temperature range is between 40°

and 100° F (4.4° and 37.8° C).

 Where the humidity is between 0 and 90%

non-condensing.

 Away from ventilation sources that can

prevent smoke from reaching the smoke
detector.

 At least 5 feet (1.5 m) from bathrooms.

When placing the SMCSD10-Z on a ceiling, mount
it in the center of the room or hallway at least 4
inches (10cm) away from any walls or partitions.

SMCSD10-Z S m o ke Detector Gui d e

Congratulations on purchasing your SMCSD10-Z Smoke Detector with Heat Detection Sensor.

The SMCSD10-Z Smoke Detector provides triple protection against fire. It combines a photoelectric smoke detector with an integrated heat
detector that senses both fixed temperature and temperature rate-of-rise within a room.

SMCSD10-Z Smoke Detector Guide

Copyright ©2013 SMC Networks Page 2

All Rights Reserved

I/M SMCSD10-Z rev. 1.0
6/18/13

When mounting the SMCSD10-Z on a wall, place
it so the top is 4 to 12 inches (10 to 31cm) below
the ceiling.

In rooms with sloped, peaked, or gabled ceilings,
place the SMCSD10-Z 3 feet (.9 m) down or away
from the highest point of the ceiling.

If mounting to suspended ceiling tile, secure the
tile with the appropriate fastener to prevent tile
removal.

Smoke detectors are not to be used with alarm
guards unless the combination has been
evaluated and found suitable for that purpose.

Note: A smoke detector does not provide

warnings for fires resulting from explosions,
smoking in bed or other furniture; ignition of
flammable liquids, vapors and gasses; and children
playing with matches or lighters.

Locations to Avoid

 Areas where normal ambient temperature

exceeds 100° F (37.8° C).

 Dirty, dusty, insect infested areas.

 In or near areas with combustion particles

(kitchens, garages, furnaces, hot-water
heaters, gas space heaters).

 On the ceiling in rooms next to kitchens,

where there is no transom between the
kitchen and such rooms.

 Damp or humid areas, or near bathrooms

with showers.

 Near fresh-air inlets or returns or very drafty

areas.

 Near heating/air conditioning vents, fans,

and fresh air intakes, which can drive smoke
away from the smoke alarm.

 In dead-air spaces at the top of peaked

ceilings or in corners where walls and ceiling
meet. Dead air can prevent smoke from
reaching a smoke detector.

 Within 10 feet (3 m) of fluorescent light

fixtures.

 Not suitable for outdoor use.

WARNING! LIMITATIONS OF SMOKE
DECTECTORS

The SMCSD10-Z Smoke Detector does not contain
a built-in audio alarm. It is not intended for
stand-alone use; it MUST be used with an
approved Touchscreen.

Wireless smoke detectors are very reliable, but
may not work under all conditions. No fire alarm
product provides total protection of life or

property. Smoke detectors are not a substitute
for life insurance.

Smoke detectors require a source of power to
work.

This smoke detector does not operate and the
alarm will not sound if batteries are dead or not
installed properly.

This SMCSD10-Z relies on the Touchscreen Alarm
to sound an audible alarm in case of fire. The
alarm may not be heard. A sound sleeper or
someone who has taken drugs or alcohol may not
awaken if Touchscreen is installed outside a
bedroom. Closed or partially closed doors and
distance can block sound. This product is not
designed for the hearing impaired.

Smoke detectors may not always activate and
provide warning early enough. Smoke detectors
only activate when enough smoke reaches the

product’s smoke chamber. If a fire starts in a

chimney, wall, roof, on the other side of closed
doors, or on a different level of the property,
enough smoke may not reach the product for it
to alarm.

Smoke detectors are a significant help in
reducing loss, injury and even death. However,
no matter how good a detection device is,
nothing works perfectly under every
circumstance and we must warn you that you
cannot expect a smoke detector to ensure that
you will never suffer any damage or injury.

SMCSD10-Z Smoke Detector Guide

Copyright ©2013 SMC Networks Page 3

All Rights Reserved

I/M SMCSD10-Z rev. 1.0
6/18/13

Current studies show smoke detectors may not
awaken all sleeping individuals. It is the
responsibility of individuals in the household that
are capable of assisting others to provide aid to
those who may not be awakened by the alarm,
or to those who may be incapable of safely
evacuating the area unassisted.

5 Installing / Replacing Battery

The SMCSD10-Z comes with two 3V Lithium
CR123A batteries preinstalled. When you need to
replace them use the following procedure. Use
batteries specified in this document
specifications or as listed on the battery
compartment cover. Use of a different battery
can have a detrimental effect on the detector
operation. Constant exposures to high or low
humidity can reduce battery life.

A. Remove the SMCSD10-Z from the mounting

base (see section 7 of this guide). Slide the
battery compartment cover away from the
SMCSD10-Z to unsnap it and lift it off.

B. If you are replacing batteries, remove and

dispose of the batteries appropriately. Wait

30 seconds after removal before continuing
to the next instruction.

C. Observing proper polarity as indicated in the

battery compartment, insert two new 3V
lithium batteries into the SMCSD10-Z battery
compartment and replace the battery
compartment cover.

Note: Use two new batteries when replacing old

batteries. Do not replace with batteries that were
used previously.

D. Reattach the SMCSD10-Z to the mounting

base and test the system.

E. The SMCSD10-Z ships with a dust cover for

protection on construction sites with dusty
environments. If your product is new, remove
the red plastic dust cover from the SMCSD10­Z.

6 Pairing with Touchscreen

Each SMCSD10-Z is programmed with a unique ID
when manufactured. The unique ID is enrolled
into the Touchscreen at the time of installation,

allowing the SMCSD10-Z to communicate with
that specific Touchscreen.

A. At the Home screen, touch the Settings

widget.

B. When the Keypad screen appears, touch the

numbers to enter your keypad code.

C. At the Settings menu, use the keypad to

enter the Installer Code (this code is the
same for all Touchscreen installed by your
company).

D. At the Technician keyboard pad, enter your

Technician ID and touch Done.

E. At the Technician Settings menu, select

Sensors & Zones > Add a Sensor/Zone. The
Locating Sensors screen appears.

F. Click Next. The system scans the premise for

wireless sensors that can be added, which
must meet the following requirements:

- Not currently paired with another

Touchscreen.

- Is active. New sensors must be activated as

follows: Turn the back cover counter­clockwise to remove. Open the battery
compartment. Removing the battery
activation tab to power on the unit.

- Defaulted if previously paired. To default

the sensor, see section 9 of this guide.

G. Follow the system prompts to complete the

add process. Trip the sensor by pressing and
holding down the Test Button on the front
cover of the detector for 10 seconds.

SMCSD10-Z Smoke Detector Guide

Copyright ©2013 SMC Networks Page 4

All Rights Reserved

I/M SMCSD10-Z rev. 1.0
6/18/13

H. When all the sensors are found and paired,

tap Done. Any located sensors that were not
paired are released by the Touchscreen and
can be added later. The Wireless Sensors
Located screen shows the number of wireless
sensors found and paired.

I. Tap Next. The Configure Wireless Sensors

screen shows icons of the sensors that were
found and paired.

J. Tap Next. The Add Sensor/Zone Modify

screen appears.

K. To modify a field on the Touchscreen, tap

the field. Use the onscreen keyboard to
enter changes. Tap Next to save changes.

L. When all sensors are configured properly, tap

Return to Menu in the Configure Wireless
Sensors screen.

M. If all sensors have not been configured, the

Modify screen appears for each sensor to let

you review its details. Change the details as
needed or tap Next to cycle through all the
sensors. The sensors are marked as
configured.

7 Mounting the Sensor

The following procedure describes how to mount
the SMCSD10-Z. Add the SMCSD10-Z to the
Touchscreen before physically mounting it in the
desired location.

A. Test communications between the

Touchscreen and the SMCSD10-Z as follows
before permanently mounting the SMCSD10­Z:

- Hold the SMCSD10-Z where you plan to

install it.

- Press the SMCSD10-Z Test button for 10-to-

15 seconds. The SMCSD10-Z sends a signal
to the Touchscreen.

- At the Touchscreen, verify the signal was

received. A message will appear in the
upper right corner of the Touchscreen for
5 seconds. If no signal is received relocate
the SMCSD10-Z and retest.

B. Using two supplied screws and anchors,

mount the base.

C. Attach the SMCSD10-Z to the mounting base

as follows:

- Line up the raised alignment tab on the lip

of the SMCSD10-Z with the arrow on the
mounting base.

- Insert the SMCSD10-Z into the base and

turn clockwise about 15 degrees until it
snaps into place.

Note: The SMCSD10-Z cannot be attached to the

mounting base if no batteries are installed.

D. Test communications between the

Touchscreen and SMCSD10-Z again:

- Press the Test button on the detector for

10-to-15 seconds. The SMCSD10-Z sends a
signal to the Touchscreen.

- Verify that the signal at the Touchscreen

was received.

E. Test the SMCSD10-Z (see “Testing the

SMCSD10-Z” on page 5).