SMC Networks 2208USB/ETH - annexe 1, EZ Networking SMC2208USB/ETH User Manual

Copyright

Information furnished by SMC Networks, Inc. (SMC) is believed to be accurate and
reliable. However, no responsibility is assumed by SMC for its use, nor for any
infringements of patents or other rights of third parties which may result from its use.
No license is granted by implication or otherwise under any patent or patent rights of
SMC. SMC reserves the right to change specifications at any time without notice.

The products and programs described in this User Guide are licensed products of SMC.
This User Guide contains proprietary information protected by copyright, and this User
Guide and all accompanying hardware and documentation are copyrighted.

SMC does not warrant that the hardware will work properly in all environments and
applications, and makes no warranty and representation, either implied or expressed,
with respect to the quality, performance, merchantability, or fitness for a particular
purpose.

Information in this User Guide is subject to change without notice and does not
represent a commitment on the part of SMC. SMC assumes no responsibility for any
inaccuracies that may be contained in this User Guide.

SMC makes no commitment to update or keep current the information in this User Guide,
and reserves the right to make changes to this User Guide and/or product without
notice.

No part of this manual may be reproduced or transmitted in any form or by any means,
electronic or mechanical, including photocopying, recording, or information storage and
retrieval systems, for any purpose other than the purchaser's personal use, without the
express written permission of SMC.

Copyright © 2004 by
SMC Networks, Inc.
38 Tesla
Irvine, California 92618
All rights reserved.

Trademarks

SMC® is a registered trademark; and EZ-Stream, EZ Connect, EZ Networking, Barricade,
and EZ Hub are trademarks of SMC Networks, Inc. Other product and company names
are trademarks or registered trademarks of their respective holders.

Compliances

FCC - Class B
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with instructions, may cause harmful interference to radio
communications. However, there is no guarantee that the interference will not occur in
a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:

• Reorient the receiving antenna

• Increase the separation between the equipment and receiver

• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected

• Consult the dealer or an experienced radio/TV technician for help

FCC Caution: To assure continued compliance, (for example - use only shielded
interface cables when connecting to computer or peripheral devices). Any changes or
modifications not expressly approved by the party responsible for compliance could void
the user’s authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.

CAUTION STATEMENT:
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with a minimum
distance of 5 centimeters between the radiator and your body. This transmitter must not
be co-located or operating in conjunction with any other antenna or transmitter. Note:
In order to maintain compliance with the limits of a Class B digital device, SMC requires
that you use a quality interface cable when connecting to this device. Changes or
modifications not expressly approved by SMC could void the user’s authority to operate
this equipment.
Attach unshielded twisted-pair cable (UTP) to the RJ-45 port and shielded USB cable to
the USB port.

EC Conformance Declaration - Class B

SMC contact for these products in Europe is:
SMC Networks Europe,
Edificio Conata II,
Calle Fructuós Gelabert 6-8, Planta 2,
08970 - Sant Joan Despí,
Barcelona, Spain.

This RF product complies with R&TTE Directive 99/5/EC (Annex IV) and with the
requirements of the Council Directive 89/336/EEC on the Approximation of the laws of
the Member States relating to Electromagnetic Compatibility and 73/23/EEC for
electrical equipment used within certain voltage limits and the Amendment Directive
93/68/
EEC. For the evaluation of the compliance with these Directives, the following standards
were applied:

• Electromagnetic compatibility and radio spectrum matters (ERM) EN300 328-1
(2001-12) and EN300 328-2 (2001-12)

• Electromagnetic Compatibility (EMC) Standard for radio equipment and services
EN301 489-1 and EN301 489-17

• Safety Test EN60950

• Immunity to conducted disturbances, Induced by radio-frequency fields EN
61000-4-6:1996 (0.15 - 80 MHz with 1 kHz AM 80% Modulation: 3 V/m)

• Power frequency magnetic field immunity test according to EN 61000-4-8:1993 (1
A/m at frequency 50 Hz)

• Voltage dips, short interruptions and voltage variations immunity test according to EN
61000-4-11:1994 (>95% Reduction @10ms, 30% Reduction @500 ms, >95%
Reduction @5000 ms)

• LVD: EN 60950 (A1/1992; A2/1993; A3/1993; A4/1995; A11/1997)

• MDD: IEC 60601-1

Wichtige Sicherheitshinweise (Germany)

1. Bitte lesen Sie diese Hinweise sorgfältig durch.

2. Heben Sie diese Anleitung für den späteren Gebrauch auf.

3. Vor jedem Reinigen ist das Gerät vom Stromnetz zu trennen. Verwenden Sie keine
Flüssig- oder Aerosolreiniger. Am besten eignet sich ein angefeuchtetes Tuch zur
Reinigung.

4. Die Netzanschlußsteckdose soll nahe dem Gerät angebracht und leicht zugänglich
sein.

5. Das Gerät ist vor Feuchtigkeit zu schützen.

6. Bei der Aufstellung des Gerätes ist auf sicheren Stand zu achten. Ein Kippen oder
Fallen könnte Beschädigungen hervorrufen.

7. Die Belüftungsöffnungen dienen der Luftzirkulation, die das Gerät vor Überhitzung
schützt. Sorgen Sie dafür, daß diese Öffnungen nicht abgedeckt werden.

8. Beachten Sie beim Anschluß an das Stromnetz die Anschlußwerte.

9. Verlegen Sie die Netzanschlußleitung so, daß niemand darüber fallen kann. Es sollte
auch nichts auf der Leitung abgestellt werden.

10. Alle Hinweise und Warnungen, die sich am Gerät befinden, sind zu beachten.

11.Wird das Gerät über einen längeren Zeitraum nicht benutzt, sollten Sie es vom
Stromnetz trennen. Somit wird im Falle einer Überspannung eine Beschädigung
vermieden.

12. Durch die Lüftungsöffnungen dürfen niemals Gegenstände oder Flüssigkeiten in das

Gerät gelangen. Dies könnte einen Brand bzw. elektrischen Schlag auslösen.

13. Öffnen Sie niemals das Gerät. Das Gerät darf aus Gründen der elektrischen
Sicherheit nur von authorisiertem Servicepersonal geöffnet werden.

14. Wenn folgende Situationen auftreten ist das Gerät vom Stromnetz zu trennen und
von einer qualifizierten Servicestelle zu überprüfen:
a. Netzkabel oder Netzstecker sind beschädigt.
b. Flüssigkeit ist in das Gerät eingedrungen.
c. Das Gerät war Feuchtigkeit ausgesetzt.
d. Wenn das Gerät nicht der Bedienungsanleitung entsprechend funktioniert oder Sie
mit Hilfe dieser Anleitung keine Verbesserung erzielen.
e. Das Gerät ist gefallen und/oder das Gehäuse ist beschädigt.
f. Wenn das Gerät deutliche Anzeichen eines Defektes aufweist.

15. Stellen Sie sicher, daß die Stromversorgung dieses Gerätes nach der EN60950
geprüft ist. Ausgangswerte der Stromversorgung sollten die Werte von AC 7,5-8V,
50-60Hz nicht über- oder unterschreiten sowie den minimalen
Strom von 1A nicht unterschreiten. Der arbeitsplatzbezogene Schalldruckpegel nach
DIN 45 635 Teil 1000 beträgt 70dB(A) oder weniger.

1| Package Contents

After unpacking the SMC2208USB/ETH, check the contents of the box to be sure you have received the
following components:

• 1 SMC2208USB/ETH USB to 10/100Mbps Ethernet Adapter

• 1 EZ Installation Wizard and Documentation CD

• 1 Quick Installation Guide

Immediately inform your dealer in the event of any incorrect, missing or damaged parts. If possible, please
retain the carton and original packing materials in case there is a need to return the product.

Please register this product and upgrade the product warranty at SMC's Web site: http://www.smc.com

2| Hardware Description

SMC’s family of USB products offers a convenient and cost-effective means of bringing straightforward
peripheral connectivity to the desktop based on the Universal Serial Bus (USB). These products feature
true plug-and-play connection of PC peripherals "outside the box" and mark a significant advance in
desktop cable management. Using the EZ Networking™ USB to Ethernet Converter you can simplify PC
connections in the home, office, or on the road.

The SMC2208USB/ETH USB to 10/100 Mbps Ethernet adapter product supports Plug-and-Play and is
easy to install. The included EZ Installation Wizard makes driver/utility installation a breeze. The USB
to 10/100 Mbps Ethernet Adapter is bus-powered, hence, it draws power from the USB port of the host PC
and requires no external power supply. Simply plug in this new SMC2208USB/ETH, which uses Type A
USB port, to your Laptop/Desktop’s USB port and connect a Category 5 cable to the RJ-45 connector. You
are now ready to connect and access network resources.

Features

• USB specification 1.0, and 1.1 for standards-based compliance to ensure compatibility

• EZ Installation Wizard

• Sleek, compact, and dongleless design

• USB bus self-powered

• Supports major operating systems

Benefits

• USB 1.0 and 1.1 supports 12Mbps high data rate performance

• EZ Installation Wizard ensures easy driver/utility installation

• Compact, easy to carry form factor; solid all-in-one design with no moving parts to break

• Draws power from the USB port of the host PC and requires no external power supply

• Supports Windows 98/ME/2000/XP, Linux kernel v2.4 or later versions, Mac 9.X & 10.X.

Compatibility

• IEEE 802.3 Ethernet, IEEE 802.3u Fast Ethernet

• USB v1.0 and 1.1 Specification

3| Driver Installation on Windows 98/ME/2000/XP

NOTE: Installation processes such as this may require the use of your original, licensed copy of Windows.

Please have your Windows CD available BEFORE proceeding with the installation.

Windows 98

1. Make sure your PC is powered on and that you are running the Windows 98 operating system.

2. Insert the EZ Installation Wizard and Documentation CD.

3. Click the [Install Driver] button to continue.

4. Insert the SMC2208USB/ETH (the A-type connector) into the USB port on your PC. The system will
display the "Add New Hardware Wizard" dialog box then click the "Next" button

.