SMC Networks SMC EZ Connect 2.4GHz 11 Mbps Wireless USB Flash Drive SMCWUSB32, WUSB32, EZ Connect SMCWUSB32 User Manual

Copyright
Information furnished by SMC Networks, Inc. (SMC) is believed to be accurate and reliable.
However, no responsibility is assumed by SMC for its use, nor for any infringements of patents or
other rights of third parties which may result from its use. No license is granted by implication or
otherwise under any patent or patent rights of SMC. SMC reserves the right to change
specifications at any time without notice.

Copyright © 2003 by
SMC Networks, Inc.
38 Tesla
Irvine, California 92618
All rights reserved.

Trademarks
SMC® is a registered trademark; and EZ-Stream, EZ Connect, Barricade and EZ Hub are
trademarks of SMC Networks, Inc. Other product and company names are trademarks or
registered trademarks of their respective holders.

Compliances

FCC - Class B
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with instructions, may
cause harmful interference to radio communications. However, there is no guarantee that the
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:

• Reorient the receiving antenna

• Increase the separation between the equipment and receiver

• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected

• Consult the dealer or an experienced radio/TV technician for help

FCC Caution: To assure continued compliance, (for example - use only shielded interface cables
when connecting to computer or peripheral devices). Any changes or modifications not expressly
approved by the party responsible for compliance could void the user’s authority to operate this
equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.

CAUTION STATEMENT:
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with a minimum distance of 5
centimeters between the radiator and your body. This transmitter must not be co-located or
operating in conjunction with any other
antenna or transmitter. Note: In order to maintain compliance with the limits of a Class B digital
device, SMC requires that you use a quality interface cable when connecting to this device.
Changes or modifications not expressly approved by SMC could void the user’s authority to
operate this equipment.
Attach unshielded twisted-pair cable (UTP) to the RJ-45 port and shielded USB cable to the USB
port.

Industry Canada - Class B
This digital apparatus does not exceed the Class B limits for radio noise emissions from digital
apparatus as set out in the interference-causing equipment standard entitled “Digital Apparatus,”
ICES-003 of Industry Canada.

Cet appareil numérique respecte les limites de bruits radioélectriques applicables aux appareils
numériques de Classe B prescrites dans la norme sur le matérial brouilleur: “Appareils
Numériques,” NMB-003 édictée par l’Industrie.

EC Conformance Declaration – Class B

SMC contact for these products in Europe is:

SMC Networks Europe,
Edificio Conata II
Calle Fructuos Gelabert 6-8, 2o, 4a
08970 – Sant Joan Despi
Barcelona, Spain

This information technology equipment complies with the essential requirements of the R&TTE
Directive 1999/5/EC and all other related provisions of this directive.

Important Safety Notices

• Unplug this product from the AC power before cleaning. Do not use liquid cleaners or
aerosol cleaners. Use a dry cloth for cleaning.

• Route the power supply cords so that they are not likely to be walked on or pinched by
items placed upon or against them. Pay particular attention to cords at plugs,
convenience receptacles, and the point where they exit from the product.

• Situate the product away from heat sources such as radiators, heat registers, stoves, and
other products that produce heat.

• To prevent fire or shock hazard, do not expose this unit to rain or moisture. Do not allow
water or any foreign objects to enter the interior. This may cause a fire or electric shock.
In the event that water or other foreign objects get into the product, immediately unplug
the AC adapter from the electrical outlet and contact Customer Service for inspection
and/or repair/replacement options.

• Do not take apart the equipment. This may cause fire, electric shock or other injuries.

• Do not overload wall outlets and extension cords as this can result in a fire or electric

shock.

• This product is for use with the AC adapter that comes with it. Use with any other AC
power is strongly discouraged as it may cause fire, electric shock, or damage to the
equipment.

1 | System Requirements

• An available USB port

• Windows 98SE/Me/2000/XP

• A minimum of 10 MB of free disk space for installing the driver and utility program.

• Another IEEE 802.11b or 802.11g compliant device installed in your network, such as the

SMC7004VWBR Barricade™ Wireless Broadband Router, or another PC with a wireless
adapter.

2 | Equipment Checklist

After unpacking the SMCWUSB32 EZ Connect™ 11 Mbps Wireless USB Flash Drive, check the
contents of the box to be sure you have received the following components:

• 1 SMCWUSB32 11 Mbps Wireless USB Flash Drive

• 1 EZ Installation Wizard and Documentation CD

• 1 Laptop Clip

• 1 USB Extension Cable

• 1 Quick Installation Guide

Immediately inform your dealer in the event of any incorrect, missing or damaged parts. If
possible, please retain the carton and original packing materials in case there is a need to return
the product.

Please register this product and upgrade the product warranty at SMC's Web site:

http://www.smc.com

3 | Installation Instructions

- Device Installation

1) Select an available USB port on the PC

2) Make sure the cap of the SMCWUSB32 is pushed down so that the USB interface is
clearly visible

3) Carefully insert the USB adapter’s Type-A plug (i.e., the flat plug) into the USB port

4) Press until it is firmly seated in the port

- Using the Laptop Clip and USB Extension Cable

1) Select an available USB port on the PC

2) Make sure the cap of the SMCWUSB32 is pushed down so that the USB interface is
clearly visible

3) Hold the cap in place while sliding the Laptop Clip onto the cap of the SMCWUSB32.
Make sure the Laptop Clip is held firmly in place.

4) Carefully insert the USB cable’s Type-A plug (i.e., the flat plug) into the USB port and
press until it is firmly seated in the port

5) Insert the other end of the cable into the SMCWUSB32 11 Mbps Wireless USB Flash Drive

4 | Flash Drive Installation

NOTE: Installation processes may require the use of your original, licensed copy of Windows.

Please have your Windows CD available BEFORE proceeding with the installation. The following
instructions are for Windows 98SE/Me. Under Windows 2000/XP, your Flash Drive should be
automatically installed once you plug the SMCWUSB32 into your USB port.

Windows 98SE

Step 1: After you have inserted the SMCWUSB32 into your USB port, the Operating System will

recognize the adapter and prompt you for the appropriate drivers. Click the [Next >] button to
begin the installation.

Step 2: Insert the EZ Installation Wizard and Documentation CD and select the [Search for the
best driver for your device] option and click [Next >].

Step 3: Clear all checkboxes except for [Specify a location:]. Then press the [Browse] button
and look for the drivers on your CD-ROM. Browse to ?:\Flash Driver. (Note: The "?" equals the
letter of your CD-ROM drive. In most cases, this is D.)

Step 4: The system should find the drivers. Click the [Next >] button to continue the installation.
The wizard will show "UStorage Drive".

Step 5: Once the system has copied the SMC drivers from the CD, it may then request files from
your original Windows disk. Please insert the Windows CD at this time.

Step 6: The system will copy the files. Do NOT press [Cancel].

Step 7: Once all the necessary files are copied from the Windows CD, the driver install process

will be complete. Click [Finish] to exit the wizard.

Step 8: You will then be prompted to reboot the machine. Press [Yes]. Upon reboot, the
SMCWUSB32 will be initialized and ready for use.

Windows ME

Step 1: After you have inserted the SMCWUSB32 in your machine and turned it back on, the OS

will automatically recognize the adapter and prompt you for the appropriate drivers. Select the

pecify the location of the driver] option. Then click the [Next >] button to begin the

[S
installation.

Step 2: Insert the Driver CD and select the [Specify a location:] option. Clear the [Removable

edia] checkbox. Then press the [Browse] button and look for the drivers on your CD. This

M
should be located in ?:\Flash Driver. (Note: The ? equals the letter of your CD-ROM drive. In
most cases, this is D.) Then click [N

ext >].

Step 3: The system should find the drivers. Click the [N

(Note: If the system could not find the drivers, click the [< B

ext >] button to continue the installation.

ack] button, and select the [Display
a list of all the drivers] option. Select [Network Adapters] from the list of devices, press [Have
Disk] and once again browse to the location of the drivers)

Step 4: Once all the necessary files have been copied, the driver installation is complete. Click
[Finish] to exit the wizard.

Step 5: You will then be prompted to reboot the machine. Press [Y

es]. Upon reboot, the

SMCWUSB32 will be initialized and ready for use.

5 | WLAN Driver/Utility Installation

Step 1: Insert the SMCWUSB32 EZ Installation Wizard and Documentation CD.

Step 2: Click the [Install Driver/Utility] button.

Step 3: Please wait while the utility checks your Operating System Version and prepares to

install the SMCWUSB32.