Smart temp 44-101 User Manual

The Smart Temp 44-101 is a precision manufactured Heat
Only Touch Screen Thermostat that offers many advanced

capabilities. Please take time to read and understand these

instructions as if properly understood the 44-101 will prove to

be a reliable thermostat controller.

Please contact Smart Temp or an authorised distributor

should you have questions about the

44-101 not covered in this manual

Manual Mode

In this mode, simply turn the thermostat On or OFF as desired by
tapping the mode button in the lower right of the LCD. When heat
mode is selected the 44-101 will activate the heating system to bring
the room to the desired set point, once the set point is reached it will
then turn the heating system off.

To set your desired temperature, tap the temperature display and
then adjust your desired heating set temperature with the Up or
Down button. Tap the temperature again or wait to exit this
adjustment window. Your new heat set point is in place.

Battery Replacement

Your 44-101 thermostat operates on 2 AAA Alkaline batteries. To
swap the batteries simply press the small door on the upper right side
of the case in and the battery compartment will pop out about 15mm.
Remove the battery tray by sliding it fully out, replace the batteries
and reinsert the battery tray back into the thermostat. Press until you
hear a click and the battery tray locks in.

Batteries will last approximately 1 year depending on use. A low
battery symbol will flash on the display when the batteries need
replacing.

Back light

The 44-101 uses a LED back light to assist using the thermostat in dark
environments. When ever you first touch the 44-101 the back light
will come on and stay on for approximately 20 seconds after the last
touch of the thermostat.

Clean

When you first touch the 44-101 a”Clean” button will be shown on the
display. Pressing the “Clean” button will diable the touch screen
functions for 30 seconds so that you may wipe or clean the touch
screen without effecting any settings. The display will show a
countdown during this time.

Covers

Optional decorative covers can be purchased to enhance the
appearance of the 44-101 thermostat. These are available in a wide
selection of colours and simply snap on to frame the thermostat. The
image above shows the 44-101 with a brushed aluminium looking
cover.

This thermostat has been proudly manufactured by smart Temp Australia P/L.

Copyright - all rights reserved.

V1.2 May 2012

Modes - Overview

The 44-101 is able to be operated as a manual thermostat for those
not requiring automatic time clock controlled temperature
regulation, or as an advanced thermostat that permits the user to pre­set times and temperatures into the 44-101 for automatic control.

Programmable Mode.

Clock
It is essential that the real time clock is set correctly if the 44-101 is to
be used in programmable mode. To set the clock tap the clock in the
top Left of the LCD. The day will flash, adjust with the Up / Down
button. Tap the clock again and the hours flash, adjust with the Up /
Down button. Tap the clock again and now the minutes flash, adjust
with the Up / Down button. Tap the clock again or wait to exit this
menu.

Programming
Depending on the options set by your installer these instructions may
vary.
Press and hold the program button to enter the programming menu.
The day (or group of days) will flash, set the day you wish to begin
programming or edit. Tap the program button again and either
Morning or Day will be shown with the hour flashing for the selected
day (or group of days), use the Up / Down button to adjust the hour
you wish the displayed event to start. Tap the program button again
and the minute will flash, adjust the minute that you wish this event to
start, tap the program button again to adjust the active or desired set
temperature that you wish at the time you have just set.

Note- If you require the thermostat to switch off at your desired
program set your temperature to 7 DegC or “--”.

Continue to tap the program button to advanced through the hour,
minute and desired temperature for events for the rest of the day.
Once you have completed a days programming you are given the
option to copy this program to other days by pressing the Up or Down
button to the highlight the days you wish to copy to. Press the
program button the begin the copy process.
Program hold
Should you wish to suspend the program for what ever reason, simply
tap the program button and the current event (morning, day evening
or night) will disappear and be replaced with the word HOLD. The
current set temperature will be held until to tap the hold button again
to cancel the hold and resume the program. You are permitted to
adjust a held programs temperature however this adjustment will be
lost and replaced with the pre-programmed temperature when you
exit program hold mode.

Temporary Override
At anytime you are able to just adjust your desired temperature by
tapping the temperature and using the Up or Down button. The
current event indicator will flash to indicate the program is
temporarily overridden. This new set temperature will automatically
expire in 2 hours.

Smart Temp

44-101

Heat Only - Touch Screen Thermostat

Smart Temp Australia P/L U20/1488 Ferntree Gully Road Knoxfield Vic 3180 Phone [phone] Fax [phone]

www.thermostat.com.au www.smarttemp.com.au

Smart Temp

Installation

Advanced Options

The 44-101 thermo stat is a heat in g o nly
thermostat. It has been fitted with a volt free relay
with change over contacts rated at 240V, 8 Amp
maximum.

Installing the thermostat is a simple process.

Open the thermostat by placing a flat blade in the two
slots at the base of the thermostat and gently pry apart.
Take care not to twist the case excessively as this may
damage the display.

Mount the baseplate
level o n t he w a l l ,
passing the equipment
wiring through the hole
in the centre of the
thermostat base. Use
the supplied screws to
mount the base to the
wall.

Please note that the equipment wiring shows 5 terminals however
only 3 are used. Two terminals shown as “X” in the diagram above
have no connection)

Equipment Terminals
Com terminal is the relay Common, voltage applied to this terminal

will be switch out. This input will accept 240V up to 8 Amps.

NO terminal is the terminal that is OPEN when no heating has been
called. This terminal is usually wired to the equipment heat call
terminal or to open a heating valve.

NC terminal is the terminal that is CLOSED when no heating is called.
This terminal is usually used to drive a heating valve closed.

X Terminal has no connection and is used to maintain a safe distance
between the other three terminals.

Sensor terminals
Com terminal is the common terminal for both the outside and

remote temperature senors.

In terminal is the indoor remote (or averaging) sensor terminal

Out terminal is the outside air temperature sensor terminal.

NC

X

NO

X

Com

NC

X

NO

X

Com

Smart Temp Australia P/L

www.thermostat.com.au

WIRE

ACCESS

HOLE

BATTERY

COMPARTMENT

MOUNTING

HOLE

Out

Com

In

NC

X

NO

X

Com

Load

Open

Closed

A

A

N

N

Heater or Boiler

Heating Valve

The Smart temp 44-101 thermostat has an advanced installer menu that
permits you to tune the performance of the thermostat to suit the
specific needs of your customer.

To enter this menu, press and hold the top left (Clock) and bottom right
(mode) of the thermostat. The display will change and show the first
option in the installer menu. Advance forward through the menu by
pressing the Mode button, move backwards through the menu by
pressing the Fan button, and adjust the menu options with the Up/Down
buttons. To exit the menu wait, or press and hold the MODE button.

1:PR Sets the number of daily programming events.

4 - Morning - Day - Evening - Night.
2 - Day - Night .
0 -Manual (no temperature programming).

2:Pd Sets Programming method.

7 - 7 day individual programming.
5 + 2. Weekday / weekend block programming.

5:Lc Sets the key lock to prevent tampering

OFF = All Functions Unlocked. 1 = Program Locked 2 = Mode
Locked. 4 = UP / DOWN Arrows Locked. 5 = Clock Locked
7 = Program & Mode Locked. 8 = Program / Mode / Clock
Locked. 9 = All Functions Locked.

7:HL Heating limit.

Sets the maximum permitted user heating set temperature.

8:Td Temperature Display

Sets deg C or deg F display modes.

9:CL Clock

Sets the clock mode. 12 or 24 hour.

10:St Show (set) Temperature

Turns the set temperature display ON or OFF.

11:BL Back light

Turns the back light function On or OFF.

12:rc Recovery

Enables adaptive recovery that starts the heating prior to
the program time so that the temperature is at the correct
value at the programmed time.

14:Sp Span

Sets how far below the set point the heating turns on.

15:CA Calibration

Permits the temperature sensor to be calibrated by up to
+/- 5c on 0.1c increments.

16:TT Temperature Terminal

Sets the remote Temperature Terminal function.
RS - replace the onboard sensor with the remote sensor.
AV - Average the onboard sensor and remote sensor.

20:Bp Beeper

Turns the onboard beeper on or off.

21:Rs Reset

Forces the 44-101 to default to factory settings. Set to on
then exit the menu to enable the forced factory reset.

Out

SC

In

RS-1

SENSOR

RS-1

SENSOR

INDOOR SENSOROUTDOOR SENSOR

Outside air or inside remote sensors can be fitted to the 44-101.
Smart temp offer a range of remote sensors for this application. The
sensors are automatically detected by the 44-101 when installed.