Page 1
Volume
Tones
Delay
Caregiver
Key™
ON
Nurse Call
AC Adapter
Reset
Button
ON
Caregiver
Key
Safety Auto-Reset
TM
Reset
Tone 3
Tone 1
T
one
2
2 Sec
0 Sec
1 Sec
PLUG IN SEAT BELT
• Plug the Seat Belt into the bottom of the desired fall alarm
monitor.
• Be sure to lace the cord through the strain relief by gently
pinching the cable into a loop and lacing it over the “Tshaped” strain relief.
TL-2109 Seat Belt Monitoring System
Step 2
Step 1
Step 3
Quick Start Instructions
SEAT BELT PLACEMENT
• Unscrew one screw on either side of the wheelchair that
holds the seat in place.
• Attach seat belt to the chair by lining up the grommet holes
with the screw holes. Re-insert screws through both the seat
belt and the chair to hold seat belt in place. Make sure that the
screws are tightened.
• Adjust Seat Belt to desired length by using the black buckle
that holds the adjustment strap in place.
• Place monitor out of reach of the resident. Suitable mounting
location is the back of wheelchair, so that the resident cannot
tamper with monitor or reach the “Reset” button.
ADJUST SETTINGS
• To adjust the volume, tone and delay, open the battery compartment in the back of the monitor to access the controls.
• Use a small screwdriver to adjust the volume to the desired
level. Please note that the monitor will be shipped with the
alarm volume set at 90 decibels (90 decibels is the legally accepted occupational noise allowance).
• Slide tone switch to the desired 3, 2 or 1 beep’s.
• Delay comes set at 0 seconds. If caregiver deems it safe and
necessary to have a delay, slide the switch to 1 or 2 seconds.
Need Set-up Help?
Call Our Friendly Customer Service Reps at (800) 650-3637
TL-2109 Seat Belt Monitoring System
1229 N. McDowell Blvd, Petaluma, CA. 94954
sales@smartcaregivercorp.com
www.smartcaregivercorp.com
Toll Free: (800) 650-3637
Step 4
TEST SYSTEM
• Buckle and Unbuckle the Seat Belt to set o the alarm.
• The monitor is now active. Alarm will sound whenever the
Seat Belt is unbuckled.
• When the alarm is activated press the “Reset” button. This will
shut down the alarming mode.
Warning: Failure to comply with warning may result in injury or death. This device is not suitable for
all individuals. Other devices may be required. This device is not a substitute for visual monitoring by
caregiver. The manufacturer does not claim that this device will stop elopement and or stop falls. This
device is to help augment caregivers comprehensive resident mobility management program. Test
this device before each use. Read the instructions and Legal Disclaimer.
Seller warrants that the goods sold will be free from defects of workmanship and manufacturing, for
a period of one year from the date of sale. Other than this limited warranty, seller makes no express or
implied warranties. Except for this limited warranty, NO EXPRESS OR IMPLIED WARRANTIES ARE GIVEN
AND NO AFFIRMATION OF SELLER, BY WORDS OR ACTION, WILL CONSTITUTE A WARRANTY. THE
GOODS BEING PURCHASED ARE BEING SOLD ON A “WITH ALL FAULTS” BASIS. THE ENTIRE RISK AS TO
THE QUALITY AND PERFORMANCE OF THE GOODS IS WITH THE BUYER. SHOULD THE GOODS PROVE
DEFECTIVE FOLLOWING THEIR PURCHASE, THE BUYER, AND NOT THE MANUFACTURER, DISTRIBUTOR
OR RETAILER, ASSUMES THE ENTIRE COST OF ALL NECESSARY INSTALLATION, SERVICING OR REPAIRS.
The Smart Caregiver Corporation Seat Belt Monitoring System is designed to be installed by the enduser. As such, it is the entire responsibility of the buyer to insure that the system is properly installed
and tested. Further, the system is not designed to replace good care giving practices including, but
not limited to:
a.) Direct patient supervision
b.) Adequate training for sta personnel for elopement
c.) Testing of the system before each use.
WHERE PERMISSIBLE, IT IS THE SELLER’S INTENT TO LIMIT ANY LIABILITY FOR SPECIAL, CONSEQUENTIAL OR INCIDENTAL ECONOMIC DAMAGES TO REFUND OF THE PURCHASE PRICE OR REPLACEMENT
OF THE GOODS. SELLER DISCLAIMS ANY LIABILITY FOR COMPENSATORY OR OTHER DAMAGES ARIS-
ING OUT OF THE USE OF THE GOODS.
WARNING: The manufacturer does not claim that this device will stop
elopement and or stop falls. This device is to help augment caregivers
comprehensive resident mobility management program. This product is to
be used by a licensed caregiver only.
UP
DOWN
TAMPER PROOF MONITOR
• To disarm the “Reset” button, slide switch on the side of the
monitor to Caregiver Key™ (patent pending) on. This allows
only the caregiver to turn o the monitor using the Caregiver
Key™ (patent pending) by passing the key over the blue circle
on the monitor marked “Caregiver Key.”
Step 5
Page 2
TL-2109 Seat Belt Monitoring System
The Wheelchair Seat belt reduces falls by triggering a fall alarm when the
“one-nger” easy release buckle is unbuckled. When the Wheelchair Seat
Belt is unbuckled, an alarm sounds so that the caregiver can attend to the
resident. The Wheelchair Seat Belt is for use with the TL-2100 Series Fall
Alarm Monitors. The easy release buckle preserves resident’s freedom of
movement by not acting as a restraint. The Wheelchair Seat Belt’s metal-re
-
inforced ends make installation easy and secure. The Seat Belt is adjustable
up to 54” and longer belts are available by special order. The Wheelchair Seat
Belt has a One Year Warranty.
Installation Instructions
TL-2109 Seat Belt Monitoring System
TL-2109 Contents:
- “One-nger” easy release buckle
- 54” adjustable belt
- Metal ends for secure installation
TL-2109 Optional Accessories (sold separately):
-Economy Fall Alarm Monitor (TL-2100E)
-Safety Auto-Reset™ Fall Alarm Monitor (TL-2100S)
-Safety Auto-Reset™ w/Voice Fall Alarm Monitor (TL-2100V)
Installation Instructions
TL-2109 Seat Belt Monitoring System
1229 N. McDowell Blvd, Petaluma, CA. 94954
sales@smartcaregivercorp.com
www.smartcaregivercorp.com
Toll Free: (800) 650-3637
Loading...