Sloan BASYS EFX-19, BASYS EFX-36, BASYS EFX-14-A, BASYS EFX-1003-A, BASYS EFX-13-A Repair Parts And Maintenance Manual
...
EFX-3XX EFX-6XX
1
9
8B
2
14 15
11 7
8A
10
6
3
4
5
Repair Parts and Maintenance Guide
BASYS®
Capacitance Sensing Activated
PARTS LIST—BASYS FAUCETS
Item
No. Code No. Part No. Description
1. 0324002 EFX-2 Standard Crown
2. 0324036 EFX-36 Control Module Mounting Kit
3. 3324113 EFX-8 Battery Pack
4. 3324114 EFX-13-A Solenoid Valve Caddy 0.5 gpm (1.9 Lpm)
3324115 EFX-14-A Solenoid Valve Caddy 1.5 gpm (5.7 Lpm)
5. 0324019 EFX-19 Filter / Strainers
6. 3324105 EFX-1003-A Control Module Assembly – 0.5 gpm (1.9 Lpm)
3324106 EFX-1004-A Control Module Assembly with Turbine –
3324107 EFX-1005-A Control Module Assembly – 1.5 gpm (5.7 Lpm)
3324108 EFX-1006-A Control Module Assembly with Turbine –
7. 0324031 EAF-31 120 VAC/6.75 VDC Plug-in Voltage Adapter
0335041 EAF-41 Plug-in Voltage Adapter (EU)
0335039 EAF-39 Plug-in Voltage Adapter (UK)
0335037 EAF-37 Box Type Voltage Adapter
8A. 0335000 EAF-1 Faucet Spout Mounting Kit (Pedestal)
8B. 0324021 EFX-21-A Faucet Spout Mounting Kit (Integrated Base)
9. 3324100 EFX-20-A 4-inch (102 mm) Centerset Base Plate Kit
10. 3324101 EFX-26-A 8-inch (203 mm) Centerset Base Plate Kit
11. 3326009 MIX-60-A Below Deck Mechanical Mixing Valve
12. 0326045 MIX-135-A Below Deck Thermostatic Mixing Valve
13. 0324033 ETF-617-A Bak-Chek® Tee
14. 0324034 EFX-33 Inlet Hose Fitting
15. 3324102 EFX-34 Flexible Supply Hose 18” (45 mm)
16. 3324104 EFX-1002-A 0.5 gpm (1.9 Lpm) Multi-Lam Spray Insert,
3324103 EFX-1001-A 1.5 gpm (5.7 Lpm) Aerated Stream Insert
3324102 EFX-1000-A 1.5 gpm (5.7 Lpm) Laminar Stream Insert
17. 0335023 EAF-23-A Splitter
18. 0335024 EAF-24-A 11-13/16” (300 mm) Extension Cable
0335025 EFX-25-A 47-1/4” (1200 mm) Extension Cable
0335015 EFX-17-A 126” (3200 mm) Extension Cable
NOTE: If changing ow rate, caddy and spray insert must be changed in conjunction.
Manufactured by Sloan Valve Company under one or more of the following U.S. Patents: 7,690, 623; 7,069,941;
6,619,320.
— in Item No. column = Not shown in illustration
17
18
— in Code No. and Part No. column = Not sold separately
0.5 gpm (1.9 Lpm)
1.5 gpm (5.7 Lpm)
includes: insert, o-ring, insert removal tool, and
hex key
includes: insert, o-ring, insert removal tool, and
hex key
includes: insert, o-ring, insert removal tool, and
hex key
12
13
IMPORTANT
Not for installation on a metal sink or
deck (i.e. stainless steel or cast metal).
The information contained in this document is subject to change without notice.
16
Electrical Connection for up to Six (6) Faucets Using One (1) Adapter
ADAPTER
DAISY CHAIN
ELECTRICAL CABLE
DAISY CHAIN
ELECTRICAL
CABLE
TO ADDITIONAL
FAUCETS
(6 MAX.)
154
Repair Parts and Maintenance Guide
BASYS®
Capacitance Sensing Activated
TROUBLESHOOTING GUIDE
1. RED LED in spout DOES NOT blink 2 seconds after battery
installation.
A. Battery placement incorrect or batteries have been discharged.
Ensure batteries are installed properly. Check the orientation of each
battery matches the positive (+) and negative (–) symbols shown on
the battery compartment.
2. Faucet DOES NOT function.
A. Adhesive packaging label afxed over sensor eye.
Remove adhesive label from sensor eye.
3. Faucet delivers water in an uncontrolled manner.
A. Faucet is not working properly.
B. Clean sensor window; if problem persists contact Sloan Technical
Support (see below).
4. Faucet DOES NOT deliver any water when sensor is activated.
INDICATOR: Solenoid valve produces an audible “CLICK”.
A. Water supply stop(s) closed.
Open water supply stop(s).
B. Strainer is clogged.
Remove, clean, and reinstall strainer. Replace strainer (lter), if needed
(refer to page 139).
INDICATOR: Solenoid valve DOES NOT produce an audible “CLICK”.
A. Batteries low (battery-powered models).
Replace batteries (refer to battery replacement on page 136).
B. Power failure (hardwire models).
Check power supply.
5. Faucet delivers only a slow flow or dribble when sensor is
activated.
A. Water supply stop(s) are partially closed.
Completely open water supply stop(s).
6. Faucet DOES NOT stop delivering water or continues to drip after
user is no longer detected.
A. Faucet is not working properly.
Clean sensor window; if problem persists contact Sloan Technical
Support (see below).
7. LED indicator blinks RED when faucet is in use.
A. Batteries low (battery-powered models).
Replace batteries (refer to battery replacement on page 136).
8. The water temperature is too hot or too cold on a faucet
connected to hot and cold water supply lines.
A. Supply stops are not adjusted properly.
Adjust supply stops.
B. For models with integral side mixing valve–mixing valve is set
improperly for the water temperature desired.
Rotate mixing valve handle clockwise to decrease water temperature or
counterclockwise to increase water temperature.
C. Inadequate hot water supply.
Adjust supply stops.
CARE AND CLEANING
DO NOT USE abrasive or chemical cleaners (including chlorine bleach) to
clean faucets that may dull the luster and attack
the chrome or special decorative nishes. Use
ONLY mild soap and water, then wipe dry with
clean cloth or towel.
While cleaning the bathroom sink, protect the
faucet from any splattering of cleaner. Acids and
cleaning uids will discolor or remove chrome
plating.
When assistance is required, please contact
Sloan Technical Support at: 1-888-SLOAN-14
(1-888-756-2614).
The information contained in this document is subject to change without notice.
155
Loading...