FUNCTIONAL SPECIFICATION
COPRECI “ReMotion” TRANSMITTER
Revision History
Rev. 0: Initial Release. M.R. 7/11/2012.
Rev. 1: Following customer review - Changed LCD indication (flashing indicator) for Thermostat Disable
and Program Disable Features; Changed factory default THERMO SET Temperature from 45-deg. F to 68deg. F. M.R. 7/13/2012.
Rev. 2: Changed number of LIGHT settings from 0-2 to 0-3 per customer request. M.R. 8/9/2012
Rev. 3: Removed Flame-A setting memory (RX restriction), added requirement for Continuous Pilot ON to
be default setting, added requirement for main flame to be ON when activating Continuous Pilot (RX
restriction), added Light/Fan/Aux disable features. M.R. 12/13/2012.
Rev. 4: Removed manual selection of Continuous Pilot Mode, specified Pilot Method for Manual,
Thermostat, and Program modes, changed reaction to 1st touch of LCD screen (will only illuminate
backlight – no reaction to associated Zone function). M.R. 12/21/2012.
Rev. 5: Made the factory default for FLAME B, FAN, LIGHTS, and Aux outputs “Disabled” and added
reference to “auxiliary module” when referencing these functions. M.R. 5/6/2013.
Objective
Define basic construction, touch-screen LCD & button layout, and operational parameters for a wireless
transmitter to operate the COPRECI “ReMotion” ignition control module & optional auxiliary module.
Basic Construction
• Transmitter body should be the same construction as current production model ReMotion TX.
• Touch-Screen LCD and three push buttons will allow input from users.
• LCD screen will provide system status & input feedback to user.
• Backlight will illuminate LCD screen for 5 seconds after any user input – the 1st touch of the LCD
screen will only illuminate the backlight (will not respond to associated zone function).
• Powered via four AAA sized batteries (6V nominal) with LOW BATTERY INDICATOR (5.0V).
Touch-Screen LCD and Button Layout (not-to-scale)
MODE Zone
ROOM TEMP Zone
SET TEMP Zone
TIME/PROG Zone
LIGHT Zone
FLAME Zone
AUX Zone
FAN Zone
DOWN Button
MODE/SET Button
UP Button
MODE/SET
Functional Description
Note: All function adjustments will be automatically accepted 15-seconds after pressing a given
touch zone or button. The user may press the MODE/SET button to immediately accept the
adjustment manually.
Day and Time Display
• The current day of week and time of day will be continuously displayed in the
TIME/PROG Zone (except during Setup operations).
• The day of week will be displayed as one of the following: S, M, T, W, T, F, S
• The time of day will be in 12-hour AM, 12-hour PM format. Midnight will be displayed
as 12:00am.
• Day/Time Setup:
o Press and hold the MODE Zone for 5 seconds to enter Day/Time Setup.
o Press the UP or DOWN Buttons to adjust the day of week (press the MODE/SET
Button or wait for 15 seconds for adjustment to be accepted, then enter hour of
day adjustment).
o Press the UP or DOWN Buttons to adjust the hour of the day. The time will
advance in 1-hour increments; AM and PM will change when the hour advances
to 12:00 midnight and 12:00 noon respectively (press the MODE/SET Button or
wait for 15 seconds for adjustment to be accepted, then enter minute of hour
adjustment).
o Press the UP or DOWN Buttons to adjust the minute of the hour. The time will
advance in 1-minute increments (press the MODE/SET Button or wait for 15
seconds and the transmitter will exit Day/Time Setup and return to normal
operation).
o LCD Displays – when in Day/Time Setup:
MODE Zone: Blank
ROOM TEMP Zone: Blank
SET TEMP Zone: Bank
LIGHT Zone: Blank
FAN Zone: Blank
TIME/PROG Zone: Day of Week, or Time of Day will Flash
AUX Zone: Blank
FLAME Zone: Blank
Pairing
• To enter pairing mode press and hold the MODE/SET Button for 10-seconds.
• Transmitter will transmit a pairing signal for 20-seconds, then automatically exit pairing
mode and return to normal operation.
• LCD Displays – When pairing mode is activated:
o MODE Zone: Blank
o ROOM TEMP Zone: The letters “On” will flash.
o SET TEMP Zone: The letter “P” is displayed
o LIGHT Zone: Blank
o FAN Zone: Blank
o TIME/PROG Zone: Blank
o AUX Zone: Blank
o FLAME Zone: Blank
Loading...