RCT-MLT-IV Remote Control Kits
Operating Control
E474962
- Installation and Operating Instructions -
INTRODUCTION
The remote control system can be operated thermostatically or manually from the transmitter. The system operates on radio frequencies (RF) within a 20 foot range. Can be used with DSI, IPI or Standing Pilot systems.
This remote control kit has a hand held transmitter that can be used as a remote on/off or as a thermostat. The transmitter display shows the current room temperature, target temperature, timer setting, on/off status, low battery indicator, current time, burner/valve operation and fan operation. Electrical ratings for the receiver are: 110 VAC, 60 Hz, 6 W.
If pertinent, see additional fireplace wiring diagrams on pages 9 to 11.
INSTALLATION PRECAUTIONS
This remote control kit is tested and safe when installed in accordance with this installation manual.
Installation of this kit MUST be done by a qualified service technician.
NOTE: A manometer MUST be used to set the manifold pressure on the gas valve.
It is the responsibility of the installer to read all instructions before starting installation and to follow these instructions carefully during installation. Modification of the remote control system or any of its components will void the warranty and may cause a fire hazard.
NOTE: The factory installed junction box in the gas fireplace must be wired with 110 VAC before installing this kit. See Installation Instructions section.
CAUTION: All wiring should be done by a qualified electrician and shall be in compliance with local codes and with the National Electric Code ANSI/NFPA No. 70-current (in the United States), or with the current CSA C22.1 Canadian Electric Code (in Canada).
WARNING: DO NOT CONNECT 110-120 VAC WIRING TO THE GAS CONTROL VALVE OF THIS APPLIANCE.
FCC REQUIREMENTS
WARNING: CHANGES OR MODIFICATIONS TO THIS UNIT NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio TV technician for help.
Canadian Equipment Requirements
This digital apparatus does not exceed the (Class A/Class B)* limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications.
This device complies with Industry Canada license - exempt RSS standard(s).
Operation is subject to the following two conditions:
(1)This device may not cause interference, and
(2)This device must accept any interference, including interference that may cause undesired operation of the device.
This device complies with RSS 210 of Industry Canada. This Class B device meets all the requirements of the Canadian interference causing equipment regulations.
Le present appareil numerique n’emet pas de bruits radioelectriques depassant les limites applicables aux appareils numeriques (de la class A/de la class B)* prescrites dans le Reglement sur le brouillage radioelectrique edicte par le ministere des Communications du Canada. Cet appareil est conforme aux normes RSS exemptes de licence d'lndustrie Canada.
Le fonctionnement est soumis aux deux conditions suivantes:
(1) Cet appareil ne doit pas causer d'interférences et
(2) Cet appareil doit accepter toute interférence, y compris les interférences pouvant entratner un fonctionnement indésirable de l'appareil.
Cet appareil est conforme å la norme RSS 210 d'lndustrie Canada. Cet appareil de classe B respecte toutes les exi-
gences du réglement canadien sur le matériel brouilleur.
Hearth & Home Technologies • RCT-MLT-IV Remote Control Instructions • 100-908 Rev. D • 12/19 |
1 |
INSTALLATION INSTRUCTIONS
Installing Electrical Service to the Junction Box
WARNING: TURN ELECTRICAL POWER OFF AT THE CIRCUIT BREAKER BEFORE BEGINNING THIS INSTALLATION.
NOTE: Some appliances do not have a cover plate. Instead, there is a hole through which the Romex clamp is attached to the outer wrap.
1.Remove the electrical cover plate from the lower side of the fireplace. Remove the knock-out from the plate and attach the Romex clamp (screws to the outside) (see Figure 1).
ACCESS HOLE |
110 VAC |
SERVICE |
COVER |
PLATE |
Figure 1 |
2.Feed the electrical service wires through the Romex clamp and secure the wires to the clamp.
3.Using the wire nuts provided, connect the service wires to the junction box. The black wires to the black service wire, the white wires to the white service wire, and the service ground wire to the ground stud of the junction box.
4.Re-attach the cover plate to the outside of the fireplace.
WARNING: LEAVE ELECTRICAL POWER OFF AT THIS TIME. DO NOT RESTORE POWER UNTIL THE REMOTE CONTROL SYSTEM IS COMPLETELY INSTALLED.
|
|
Wire Colors |
• |
Gas Valve - Millivolt or |
|
|
Electronic Ignition .............................................. |
Red |
• Fan/Blower - 110 VAC ......................... |
Plug from Fan |
|
• |
Flame Controller - HI/LO solenoid.................. |
Orange |
RECEIVER WIRING INSTRUCTIONS
Incorrect wiring connections WILL cause damage to the gas valve or electronic module operating the gas appliance and may also damage the remote receiver.
Wiring Flame Function (Standing Pilot, DSI, IPI)
Connect the remote receiver by connecting the two red wires leading from the remote receiver to the red and brown remote wires labeled “FOR USE WITH REMOTE OR WALL SWITCH ONLY”. See Figure 2.
|
RED |
RED ORANGE |
ORANGE |
|
RED |
|
VALVE |
|
|
TH |
|
ON/OFF |
|
|
|
SWITCH |
REMOTE SWITCH |
RED |
|
|
PIGTAIL |
TP |
|
|
|
||
|
RED |
|
TP TH |
|
BROWN |
|
|
|
WALL |
|
|
|
SWITCH |
|
|
Figure 2. |
|
|
|
Alternative Wiring for units with a wall switch
Disconnect the wall switch wire from the TH terminal on the valve and connect this wire to male connector supplied on the receiver. Connect remaining female connector from receiver to the TH terminal on the valve.
Adding Optional Fan/Blower
REMOTE RECEIVER |
Plug 2-prong fan cord directly into the 3 prong polarized plug |
|
on the back of the receiver (see Figure 3). This receptacle |
||
Important: The remote receiver should be positioned |
output is 110/120 VAC, 3 AMP. |
|
close to front in right or left corner where ambient |
|
|
temperatures do not exceed 170º F. |
|
|
The remote receiver is powered by 110-120VAC. It plugs |
(Receptacle on back) |
|
into a standard polarized duplex receptacle. |
|
|
NOTE: If junction box contains 2-prong receptacles, a standard |
|
|
3 to 2 prong adapter will be required to be obtained from an |
|
Line cord |
independent source. |
|
from fan |
Locating Receiver and Operating Functions |
|
|
This remote receiver can be positioned under the firebox |
|
|
in the control compartment of the fireplace if ambient tem- |
|
|
peratures do not exceed 170º F. This system is designed |
Figure 3. Adding Fan/Blower |
|
to control the following components: |
|
|
Hearth & Home Technologies • RCT-MLT-IV Remote Control Instructions • 100-908 Rev. D • 12/19 |
2 |
|
GAS CONTROL |
KNOB |
VALVE |
|
SCREW
NUT
WASHER |
VARIABLE REGULATOR |
|
|
|
WASHER |
VARIABLE |
|
SOLENOID |
REGULATOR |
|
|
FLAME CONTROL |
VARIABLE |
JAM NUT |
SOLENOID |
REGULATOR |
PLUNGER |
|
Figure 4.
NOTE: All steps required for installation of the flame controller MUST be done by a qualified gas service technician.
Installing Flame Control Solenoid
1.Remove the screw and knob from the variable regulator and discard.
2.Unscrew the nut from the regulator and discard.
3.Remove the bag containing a washer and blue and red plungers from the side of the flame control solenoid.
4.Place washer on flame control solenoid (see Figure 4).
5.Insert the correct plunger (blue - natural gas, red - propane) into the flame control solenoid (see Figure 4).
6.Thread the flame control solenoid with correct plunger into the thread hole in the variable regulator. Turn one to two turns only. Do not tighten or damage may occur.
Wiring the Flame Controller
1.Connect the two leads from the flame control solenoid to the orange leads from the receiver (see Figure 5).
2.Install a manometer into the pressure tap.
NOTE: A manometer MUST be used to set the manifold pressure on the gas valve.
3.Plug the remote receiver into the 110/120 VAC power supply.
4.Light the fireplace as directed in the Owner’s Manual.
5.Set the manifold pressure on the gas valve by rotating the flame control solenoid. Adjust until the reading on the manometer is 3.5 inches w.c. for natural gas, or 10.0 inches w.c. for propane.
6.Tighten the jam nut (see Figure 4) to the face of the variable regulator body.
7.Turn the main gas knob on the gas valve OFF.
8.Remove the manometer from the pressure tap and screw the tap closed.
RED RED ORANGE ORANGE |
ORANGE |
RED |
ORANGE |
JAM NUT |
PLUNGER |
REGULATOR |
TOWER |
Figure 5. |
Hearth & Home Technologies • RCT-MLT-IV Remote Control Instructions • 100-908 Rev. D • 12/19 |
3 |
The remote receiver has a 3-position slide switch: OFF/ REMOTE/ON (see Figure 6).
OFF - REMOTE - ON |
SWITCH |
Figure 6. Remote Receiver |
NOTE: The remote receiver will only respond to the transmitter when the 3-position slide button on the remote receiver is in the Remote position. If the system does not respond to the transmitter on initial use, see section Matching Security Codes.
1.With the slide switch in the ON position, the system is on.
2.With the slide switch in the REMOTE position, the system only operates if the remote receiver receives commands from the transmitter.
3.With the slide switch in the OFF position, the system is off.
NOTE: The slide switch should be placed in the OFF position if you will be away from your home for an extended period of time. Placing the switch in the OFF position also functions as a safety “lock out” by turning the system off and rendering the remote receiver inoperative.
TRANSMITTER
Important: Before operating remote control, transmitter and receiver must have matching security codes. See section ‘Matching Security Codes’.
Important: Review ‘Thermo-Updating/Communication- Safety Features’ under ‘Transmitter Safety Features’ section. Communication Safety features shut down the fireplace system when a potentially unsafe condition exists.
Important: Review ‘Auto Shutdown’ section. This safety feature shuts down the fireplace after 9 hours of continuous operation, in ON mode only.
Important: New or fully charged batteries are essential for proper operation of the multi-function transmitter. The transmitter operates on 2 AAA-size 1.5V batteries. Use Alkaline batteries for longer battery life and maximum operational performance.
Insert 2 AAA-size 1.5V batteries into the battery compartment on the back of the transmitter. When the batteries are correctly inserted, the screen will display numbers (see Figure 7 for LCD Display Screen).
NOTE: If the transmitter is activated from a very cold condition it may be necessary to allow the transmitter to stabilize to room temperature (could take up to 15 minutes) before accurate room temperatures are displayed on the screen.
NOTE: LCD screen is equipped with a “backlite” for easier viewing of LCD screen. Backlite illuminates when a function button is depressed. After 5 seconds elapses, LCD screen will return to its normal state.
Hearth & Home Technologies • RCT-MLT-IV Remote Control Instructions • 100-908 Rev. D • 12/19 |
4 |
Loading...