Digital
Harddisk
Receiver
SSKY
KY
M
M
A
ASSTTEE
R
R
D
D
V
V
R
R
9400
9400
INSTRUCTION MANUAL
General Information .................................... 41
Main Feature of Receiver 41
For your Safety 42
Unpacking 42
General Operation of Receiver 42
RCU 43
Front Panel 44
Rear Panel 44
Installation of Receiver .............................. 45
Connecting to Antenna & TV 45
Connecting to TV & VCR using SCART 45
Connecting to TV using RCA support 46
Connecting to TV using S-VHS support 46
Connecting to another SVR 47
Connection to Digital Amplifier 48
Menu Information ...................................... 49
User Installation .......................................... 50
Antenna setup - 1) DiSEqC 1.2 50
Antenna setup - 2) Fixed 51
Channel search -1) DiSEqC 1.2 52
Channel search - 2) Fixed 53
System setting 54
Parant Lock 55
Factory Default 56
Common Interface ...................................... 57
General Viewing Function .......................... 58
Select Channel 58
Pause the Frame 59
Previous Channel Recall 59
TV & Radio mode 59
TV & VCR mode 59
Channel Information 60
Volume & Audio Control 60
Position 61
Sat 61
Channel Manager ........................................ 62
Channel Manager 62
Favorite Channel 63
Move Channel 63
Lock Channel 64
Rename Channel 64
Delete Channel 65
Sort Channel 65
Fast Edit mode 66
Go to Function ............................................ 66
Hard Disk Recorder .................................... 67
Time-Shift mode 67
Playback mode 69
Timer Recording 69
EPG Recording 70
HDD Manager 70
7-Segment Display 70
EPG (Electronic Program Guide) ................ 71
Timer ............................................................ 72
Antenna Positioning Help .......................... 73
Front Panel Display .................................... 74
Trouble Shooting ........................................ 74
Safety Information
Keep the DVR 9400 away any water like flower vases, tubes, sinks, etc. Never open the unit. Touching internal parts
of this unit is dangerous. Do not attempt to disassemble the DVR 9400 or repair the AC power cord in any way.
Avoid placing the unit in areas of direct sunlight or heating radiators.
Trade Mark of the DVB Digital Video Broadcasting Project
40
Content
41
Main Feature of Receiver
General Information
• High quality Digital Video & Audio
• Fully MPEG2, DVB compliant
• 2 Slots Common Interface for Viaccess, Irdeto, CryptoWorks, Nagravision, Conax, SECA and
more
• DiSEqC 1.2 Positioner for multi-satellites (63 satellites)
• C/Ku band control for each antenna
• Provide friendly and easy-to-use menu system
• Various channel editing function (favorite, moving, locking, renaming, deleting and sorting)
• User programmable various Satellite & Transponder information
• Automatically search for newly added transponder (Network Auto Search)
• Stores up to 2000 channels
• OSD four color changeable (Night, Wine, Ocean, Grass)
• Easy and speedy software upgrade through RS-232 port
• Plug-and-play data transfer system (DSR to DSR)
• Automatically each channel volume saving function
• Timer function, automatically turns On/Off by setting function (daily, monthly, yearly)
• Automatic reserved channel moving system
• Provide Electronic Program Guide (EPG)
• Teletext function support
• Antenna Positioning Help feature
• Selectable Video output – CVBS, RGB
• Provide various switch types, LNB types and NTSC/PAL monitor type
• SCPC/MCPC Receivable from C/Ku Band Satellite
• Multi LNB controlled by DiSEqC 1.2 and 22KHz, 0/12 volt switching
• 256 colors On-Screen-Display
• PAL/NTSC automatically conversion
• Last channel automatically saving
• Recording reservation function by Timer and EPG
• Recording and playback with Time-Shift function
• 3 Step Fastforward function(X4, X8, X16)
• 3 Step Rewind function(X4, X8, X16)
• Pause and Step playback function
• 30 hours recording available with 40 GByte HDD in 4Mbps stream
• Recording program management function (Play, Move, Lock, Rename, Delete)
• Jump playback function
• Record a program and play another recorded program at the same time
• Repeat playback function
• Shuffle playback function
Technical alterations reserved
A Digital Satellite Receiver is a convenient product that allows you to view a variety of programs
provided through satellite. This user’s guide covers the installation of the DSR and the necessary
steps to implement various features. This also explains special features available only in this DSR
in detail, which will allow you to make full of these feature.
For Your Safety
42
• Allow clear space around the Receiver for sufficient ventilation
• Do not cover the Receiver or place it on a unit that emits heat
• Use a soft cloth and a mild solution of washing-up liquid to clean the casing
• Do not connect or modify cables when the Receiver is plugged in.
• Do not remove the cover
• Do not allow the unit to be exposed to hot, cold or humid conditions
•
Never allow liquids, spray or other materials to come into contact with the inside of the
DVR 9400
Unpacking
After purchasing the DSR, unpack it and check to make sure that all of the following items are
included in the packaging.
1 x Remote Control Unit (RCU)
1 x User’s Guide
2 x AAA batteries
1 x DSR
General Operation of Receiver
Throughout this manual you will notice that the everyday operation of your Receiver is based on
a series of user friendly on screen display and menus. These menus will help you get the most
from your Receiver, guiding you through installation, channel organizing, viewing and many other
functions.
All function can be carried out using the buttons on the RCU, and some of the function can also
be carried out using the buttons on the front panel.
If at any time when you using the menus you want to return to the normal TV mode, press the
TV/AV button.
The Receiver is easy to use, always at your command and adaptable for future advances.
Please be aware that new software may change the functionality of the Receiver
Should you experience and difficulties with the operation of your Receiver, please consult the
relevant section of this manual, including the Problem Shooting, or alternatively call your dealer
or a customer service adviser.
Key Function
Turns power ON/OFF of the DSR
When watching a channel, mutes the sound
0 ~ 9 Enter number of the required menu item or
select a channel number to watch.
TV/RADIO Switches between TV and Radio mode
PR Switches back to previous channel
FAV Display the favorite channel list
INFO Shows information of the current channel
MENU Press this key one time to run menu on
screen, and call command box
Moves up / down a page in the channel list
OK, LIST Executes the selected item in the menu
screen, or enters the desired value in any
input mode.
SAT Display the satellite list of searched chan-
nels
PR+, PR- When watching a channel, change chan-
nels, or moves to the next higher or lower
item in the menu.
When watching a channel, adjust the volume, or move to the left or right item in
menu
EXIT Returns to the previous menu on the menu
screen or escape from the menu
ALT-AUDIO When watching a channel, switches the
audio languages
EPG Calls up the EPG (Electronic Program Guide)
Selects the different audio modes.
TV/AV Switches between TV or AV mode.
Position Display position bar on the screen to adjust
the antenna or for manual search.
Switches to teletext or subtitle mode.
UHF No Funktion
REW Rewind program with 3 step speed
PLAY/SLOWDisplay file list in Live mode. Playback
program by normal or slow speed
STOP Stop recording or playback.
F.F Fast forward program with 3 step speed
PAUSE
Pause screen and audio. Start recording in
Live mode.
REC Record program.
RCU
43
44
Front Panel
Rear Panel
Turns on and off the power of the receiver.
CH When watching, changing to the previous and next channel, or moves to the next higher
or lower item in the menu.
1. Power ON/OFF
2. Connect to 12V to an External 0/12V Switch
3. Connect to the S-VHS Jack of TV or VCR
4. Connect VIDEO to TV using RCA Jack
5. Connect to AUDIO R/L to TV or AUDIO Tuner
6. Connect to TV using a SCART Cable
7. Connect to VCR using a SCART Cable
8. Connect to a PC for S/W upgrade
9. LNB IN : Connect to SATELLITE ANTENNA
10. LNB OUT : Connect to the other Receiver (DVR 9400 must be switched off)
11. Connect to Digital Amplifier
1 2 6 9
3 4 5 87
10
11
45
Installation of Receiver
Connecting to ANTENNA & TV
This section explains the installation of Receiver. Refer to the manuals supplied with the equipment for the installation of outdoor equipment such as the dish antenna. When adding new
equipment, be sure to refer to the related parts of the manual for the installation.
Connecting to TV & VCR using SCART support
46
Connecting to TV using RCA support
Connecting to TV using S-VHS support
47
Connecting to another SVR
48
Connecting to Digital Amplifier
111149
Once you have correctly connected the Receiver, the menu will be displayed
This menu consists of 7 major main menus as below.
- Channel Manager
- Program Guide
- Timer
- User Installation
- Common Interface
- Receiver Information
- HDD Manager
During the installation the OK key confirms a selection and LIST key shows Down List Box if the
column has “+” mark. You can also use the numeric keys on the RCU Unit (RCU) to enter numeric
value.
Use the PR+, PR- key to move upwards and downwards from one line to another line and use
key to move from main menu to sub menu and move from left side to right side or versa.
Meantime, you want to escape the menu system, please press EXIT key on the RCU.
Menu Information
50
User Installation
This menu consists of 5 major sub-menus as below.
- Antenna Setup
- Channel Search
- System Setting
- Parental Lock
- Factory Default
Antenna Setup (1) DiSEqC 1.2
1) Antenna: You can select maximum 16 anten-
nas with the combination switches.
2) Type: Select your antenna type as
DiSEqC 1.2
3) Univ. LNB: Select your LNB type. If you have
universal LNB, select YES
otherwise select NO.
4) LNB Freq.: Enter the proper LNB frequency
referring to your LNB using numeric key on the RCU or use KEY PAD displayed
by pressing OK key.
If you have a dual LNB, enter the proper value in the both of value box.
5) Switches (0/12 Volt, 14/18 Volt, DiSEqC):
You can select the switches with which you want to configure the antenna.
6) C/Ku band control:
You can select C/Ku band control by switches types.
7) East, West Limit:
Press E key on the RCU until your
antenna will be reach to be
easternmost and then press OK
key on the RCU. The message of
“Would you like to set East limit of
DiSEqC motor?” will be displayed
for your confirmation, please select OK button by pressing OK key
on the RCU and then East limit
value will be changed as SET.
The usage of West limit is same
as East limit.
51
8) Reset DiSEqC limit:
If you want to reset the East limit
or West limit, place a cursor on
Reset DiSEqC Limit button and
then press OK key on the RCU. The
message of “Would you like to
reset limit for DiSEqC positioner?”
will be displayed for your confirmation, please select OK button by
pressing OK key on the RCU.
The cursor will move to the East
limit button so that you can reset
the limit. After that, please reset West limit same as before.
After setting all necessaries, please EXIT to finish antenna setup menu. The message of “Are you
sure to change the configuration of Antenna setup?” will be displayed. Please select OK button
on the screen and then wait for saving a data.
1) Antenna: You can select maximum 16 an-
tennas with the combination
switches.
2) Type: Select your antenna type as Fixed
3) Univ. LNB: Select your LNB type. If you have
universal LNB, select YES
otherwise select NO.
4) LNB Freq.: Enter the proper LNB frequency
referring to your LNB using numeric key on the RCU or use KEY PAD displayed
by pressing OK key.
If you have a dual LNB, enter the proper value in the both of value box.
5) Switches (0/12 Volt, 14/18 Volt, DiSEqC):
You can select the switches with
which you want to configure the
antenna.
6) C/Ku band control:
You can select C/Ku band control
by switches types.
After setting all necessaries, please EXIT to finish
antenna setup menu. The message of “Are you sure
to change the configuration of Antenna setup?” will
be displayed. Please select OK button on the screen and then wait for saving a data.
Antenna Setup (2) Fixed
52
1) Antenna: Select your antenna number.
2) Satellite: Select desired a satellite using
56kk keys or if you press OK key
the Down List Box will be displayed so that you can choose easily.
You can see the information of
selected satellite in the right side.
Edit Mode: If you want to edit
those preprogrammed data such
like a Transponder, Frequency,
Symbol Rate, Polarization, Skew
and 22 KHz, please press MENU
key on the RCU to display the
command box. Check edit mode
by pressing OK key on the RCU
and then you can move into those
columns to change the value.
3) Position: After selecting a satellite, please
select Position button and then
keep pressing E or W key on the
RCU until selected satellite is
locked. If the satellite is locked
correctly, the color of signal label
bar will be changed to yellow.
Then press OK key on the RCU, the message of
“Would you like to set the value of current positioner?” will be displayed for your confirmation.
Channel Search (1) DiSEqC 1.2
53
1) Antenna: Select your antenna number.
2) Satellite: Select desired a satellite using
keys or if you press OK
key the Down List Box will be
displayed so that you can choose
easily.
You can see the information of
selected satellite in the right side.
3) Edit Mode: If you want to edit those prepro-
grammed data such like a Transponder, Frequency, Symbol Rate,
Polarization, Skew and 22 KHz,
please press MENU key on the
RCU to display the command box.
Check edit mode by pressing OK
key on the RCU and then you can
move into those columns to change the value.
Channel Search (2) Fixed
54
System Setting menu allows you to change the the
principal option and to set other items proper to your
environment by pressing OK key on the RCU.
OSD Color: Select your favorite color
OSD Language:
Select your desired language
LNB power: If your Receiver is connected to
LNB, select YES. But if your
Receiver is connected to other
receiver through Loop Through
support, you should check which
receiver is connected directly to
LNB. In case if that other receiver
is directly connected to LNB, select OFF.
Screen Format: If your TV supports 16:9 screen
format and selected channel provides 16:9 format program, select
16:9.
Video output: If your SCART supports RGB con-
trol, select RGB. Otherwise select
CVBS.
TV type: Select the type according to your
TV type.
Volume save: If you select ON, you can save
automatically last volume level for
each channel.
Start On Channel: If you press OK key, then the channel list is displayed. You can select one
channel of the list, the selected channel starts whenever you turn on LT
3000D.
UHF Standard: Select UHF type.
UHF Channel: Select your desired UHF channel for satellite mode.
Note: Receiver for the country, in which it is not used UHF, 11) and 12) option will be deleted.
System Setting
55
This function allows you to lock the channel with
your password in order to prevent from accessing the
channel by your children or any other person.
And also you can protect your installed data and
information using Install Lock.
How to change Password
1) Enter the current password.
2) Select ON of Parent Lock.
3) Enter new password.
4) Confirm your new password entering new password again.
Note: Default password is 0000.
Warning: Do not forget your password in order not to fail to view the channel.
How to use Parent Lock
1) If you activate parent lock function, go to the
TV channel Manager Page.
2) Press Open command box and select Lock
3) Select channel the which you want to Lock
4) Press OK then symbol is marked.
5) Exit this menu and Turn off the Receiver
Note: To activate Parent Lock, you have to turn off
Receiver once.
And turn on the Receiver and select channel which
is locked. Then enter your password.
Parental Lock
56
How to use Install Lock
1) Enter the current password.
2) Select ON of Install Lock
3) Enter new password
4) Confirm your new password entering new
password again
5) Exit this menu and Turn off the Receiver
6) Turn on Receiver and press MENU key on the RCU
7) Select any menu and press OK on the RCU.
8) Then Enter Password Box will be displayed.
9) Unless enter correct password, you can not run any menu.
Note: Default password is 0000
Warning: Do not forget your password in order not to fail to operate Receiver
Factory Default
If you want to bring Receiver back to the factory
default condition, select Factory Default and press
OK key.
Then Warning message will be displayed. To confirm
select OK and press OK.
Warning: You will lose all of data and information
which was installed.
57
Common Interface
Receiver makes you enjoy various scrambled channels encrypted by Viaccess, Nagravision,
Irdeto, Conax, Cryptoworks and SECA.
Preparing
To be able to receive scrambled digital satellite channels you will need a Smartcard and a Common
Interface CA (Conditional Access) module form the
Service Provider of your choice.
The Smartcard and the CA module may also provide
access to special menus not described in this
manual. If so, please follow the instructions from the
Service provider.
Only free to air channels are available without the
Smartcard and CA Module.
Input the CA Module in the slot of Receiver. And insert
Smartcard to the CA module entirely. If it is done, you
can enjoy scrambled channels relating with your CA
Module and Smarcard.
Note: Receiver has 2 slot for CA Module
Check Manager
Select Common Interface menu in the Main Menu
page. Then Receiver detects and shows the CA
Module names, which you insert. Then select slot
1 or slot 2, which you want.
Then you can see the information, which Program
provider presents.
Note: This information may be different according to
the Program Provider.
58
General Viewing Funtion
The following describes the basic functions of your Receiver while watching satellite TV or
listening to satellite radio.
If you select a channel to which you do not have access, you will get a message on the screen.
This message may vary, depending on type of program and Service Provider. In the case of
“Scrambled Channel message”, you can not view with Receiver and you are requested to
purchase our Receiver which make you view the several scrambled programs.
While viewing, the current channel information will be shown on the bottom of the screen if you
press INFO button on the RCU
In addition to the normal function, there are some other useful functions which will be explained
in this part of manual.
Select Channel
If you want to change channel, use CH key on the
front panel or PR+, PR- key on the RCU. Or using the
numeric key on the RCU, referring to the LED on the
front panel.
In addition to the above normal function, Receiver
provide more convenient channel change function.
While viewing, press OK key on the RCU or front
panel. Then channel list will be displayed on the right
side of the screen. If press EXIT key, the channel list
will be disappeared.
Using PR+, PR- or CH key, place the cursor on your desired channel, which will be changed to
yellow color. Then press OK key go to the selected channel.
If there are a lot of channels listed, use or key on the RCU, then you can move from page to
page.
Note: Receiver is designed to search all of free channels in the selected Satellite. So if you install
in the first time, Receiver show only free channel list.
59
Press PAUSE key on the RCU to pause the screen. To bring it back to the normal mode, press
PAUSE key once again.
Previous channel recall
Press %PR key on the RCU to move the previous channel which you watched before.
TV & Radio mode
While viewing TV channel, press TV/RADIO key on
the RCU to move radio mode. Press this key once
again, it will bring you back to the TV mode.
TV & VCR mode
While viewing satellite channel, press TV/AV key on the RCU to move TV mode. Press this key
once again, it will bring you to the VCR mode. To move satellite channel, press this key once
again.
Note: In this case, you can see the current mode through LED display on the front panel.
Pause the frame
60
Volume & Audio Control
1) Volume Control:
To increase or decrease volume,
use key on the RCU or
VOL< > on the front panel.
Note: Receiver has 18 volume levels and this shall
be controlled from the adjusted volume level of your
TV.
2) Mute: To mute the sound, press but-
ton on the RCU. To bring back the
normal sound condition, press this
key once again.
3) Audio Control:
Press the key repeatedly to
select one of three possible Audio
settings (Left, Right and Stereo)
The current audio condition will be displayed in the
channel information
4) Language Selection:
Press the ALT-AUDIO key on the
RCU to repeatedly select audio-language. This is dependent on the transmission of audio signal which supports Multi-language.
Channel Information
Every time you change channels, you will receive
program information for a few second.
While viewing channel, you can see the current channel information anytime, pressing INFO key on the
RCU.
Note: Channel information will be shown for a
5 seconds.
61
Sat
If you want to have a channel list for each satellite
when you searched one more satellite, press SAT key
on the RCU then all satellites list which you already
searched will be displayed.
Select one satellite you want, press OK key on the
RCU then you will have a channel list for only you
want.
Position
If you need to adjust the antenna more accurately to
watch a clear channel, press POSITION key on the
RCU and then the position bar will be displayed.
Press E or W key on the RCU to adjust for clear channel.
Otherwise, you can use this function for manual
search instead of Auto tracking.
62
Channel manager consists of TV channel manager
and Radio channel manager. Press OK key placing
the cursor on the TV Channel.
Note: Since the usage of Radio Channel manager is
same as that of TV channel manager, in this menu
only TV Channel manager is explained.
In this menu you can see the channel list which
Receiver searched in the left side and in the right
side, Current channel information is displayed.
Press MENU key on the RCU, then command menu will be displayed
TV channel manager has 9 commands as below;
1. Favorite channel
2. Move channel
3. Lock Channel
4. Rename Channel
5. Delete channel
6. Sort channel
7. Fast edit mode
8. Go To
9. Exit
Select your desired function pressing OK key.
Please select Favorite.
Channel Manager
Channel Manager
Receiver provides most powerful channel managing function in the world and this function allows you to have a more interesting and useful operation as well as viewing channels simply.
63
Move Channel
In Main Page, press MENU key on the RCU, and then
select MOVE on the commands.
This MOVE command allow you to change the channel number. First select the channel, which number
you want to change pressing OK key, and then using
PR+, PR- key, move the channel on your desired
location. Then press OK key to confirm your change.
And check whether the channel number is changed
on the channel list.
Select your favorite channel and then press OK key.
Then 1 will be marked at rear of your selected chan-
nel name.
And if you want to delete the channel name in the
favorite channel list, press OK key once again, then
the 1 mark will be disappeared.
If you selected all of your favorite channels, please
return to the Main Page, pressing EXIT key once
more to exit Main Page. Then changed channel list
will be displayed, if you press OK key.
Note: Receiver is designed to select auto-matically all of free channels as favorite channel. So
after perform Install Wizard, all free channel is selected in your favorite channel list.
*
$ means scrambled channel.
Favorite Channel
64
Rename Channel
In Main Page, press MENU key on the RCU, and then
select Rename on the command menu.
This Rename command allow you to rename the
channel. First select the channel, which you want to
lock, pressing OK key and then Keypad Dialog Box
will be displayed. Edit your desired name entering
word or number.
And check whether the channel name is changed on
channel list.
In Main Page, press MENU key on the RCU, and then
select Lock on the command menu.
This Lock command allow you to lock the channel.
First select the channel, which you want to lock,
pressing OK key and then will be marked at rear
of your selected channel name.
Note: To perform this function, you should set up the
Parent Lock which is explained after.
Lock Channel
65
In Main Page, press MENU key on the RCU, and then
select Delete on the command menu.
This Delete command allows you to delete the channel permanently. First select the channels, which you
want to delete, then selected channel number will be
changed to yellow color. If you cancel the selection,
press OK key again, then the number color will be
back.
If you decided to delete, press EXIT key and then
Message box will be displayed. Press OK to delete.
And check whether the channel number is changed exiting on channel list.
Warning: The deleted channel can not be recovered unless you search again. Please be careful
when you decide to delete channel.
Delete channel
Sort Channel
In Main Page, press MENU key on the RCU, and then
select Sort on the command menu.
This Sort menu has its sub command and it allows
you to sort the channels as your desired way.
You can sort the channels by Favorite, Lock,
Scramble, SAT name and CH name. Place the cursor
on your desired line, and then press OK key.
And check whether the channels are sorted exiting
on the channel list
Note: Radio Channel Manager is same operation as TV channel Manager.
66
Fast Edit mode
Fast edit mode allows you to edit channel fast without showing channels selected.
If you turn off the Fast edit mode, Receiver will
shows each channels elected in the TV Channel
Manager mode and it takes few seconds.
Note: Fast edit mode is default, when you operate
Receiver for the first time.
Go To function
Many customers feel difficulty to set up the other
receivers, because the menu system is too much
complicate.
But the menu system of Receiver is made by Open
Architecture Concept for users to move their location
to any other menu with one step in our GO TO
Function. This is the one of the powerful function of
Receiver and allows users to setting the system most
easily in the world.
How to use GO TO function.
1. Press MENU key on the RCU in the menu.
2. Select a TV Channel in the Channel Manager.
3. After your working in the TV Channel, press MENU key on the RCU.
4. Then menu box will be displayed.
5. Select Go To menu and press OK key.
6. Then sub-menu list will be displayed.
7. Select Timer and press OK key.
8. Then you can go to the Timer Page directly.
9. If you go back to TV Channel, repeat the procedure of Go To function.
67
DVR 9400 is equipped with a hard disk and allows you to record current programs while playing
back earlier recordings simultaneously. Also it makes you free from one-way broadcast times
through time-shift function. When you need to leave your seat on urgent business, you can playback from the paused screen with time delay after come back and also DVR 9400 enables you can
determine the start time of a program you want independent of the broadcast time.
Time-Shift mode
In the Time-Shift mode, recording and playback can
be carried out simultaneously. You can playback the
recorded program with time delay as much as you
want to keep recording live signal.
1) Recording
You can record a program which you are watching
now by pressing REC or PAUSE key on the RCU then
the front panel will be displayed as r-P by seven
segment.
- Using REC key
If you press REC key on the RCU, you can record the
current viewing program internally while watching
the program at real time.
- Using PAUSE key
If you press PAUSE key, the current broadcasting program (audio & video) is paused but starts recording it
internally.
2) Playback / Slow playback
If you press PLAY key on the RCU, the recorded program plays in normal speed with time delay
and then if you press PLAY key again, it plays in slow. However, the program is recording continuously internally unless you press STOP key.
Hard Disk Recorder
68
Time-Shift mode
- FF, REW
If you press F. F key repeatedly, the recorded program
plays forward in x4, x8, x16 speed than normal speed
and, press REW key repeatedly, the recorded program plays backward x4, x8, x16 speed than normal
speed.
In that case, you can check the speed as the mark >,
>>, >>>,>>>> in the upper left side on the screen.
- Pause
If you want to playback the recorded program step by
step, press PAUSE key repeatedly.
3) Playback while recording current program
If you want to playback of earlier recorded program
while recording current program simultaneously,
please press OK key on the RCU. The file list will be
displayed on the screen and then select a program
what you want to playback.
4) Save & Stop
If you press STOP key on the RCU in the Time-Shift mode, a Dialogue box pops up and then you
can save the channel. Also it asks you whether you will save it as a channel name. If you want to
change file name what you want, please press OK key at the column of file name than alphabet
box will be displayed on the screen. Finally if you want to save the program, please select YES
button in the box and then it returns to Live mode. Otherwise if you select NO button it returns to
Live mode without saving.
Info-Bar
While playing back or recording, if you press INFO
key on the RCU, Info-bar is appeared on screen and,
unless you press EXIT key, Info-Bar is displayed in
continuous.
The Info-bar shows icons, total recording time, playing time and remaining HDD size.
While displaying Info-bar, if you press keys
then current playing pointer will jump to previous or next.
If you press INFO key after disappearing of the Info-bar, the info-bar appears again and, unless
you press EXIT key on the RCU, Info-Bar is not disappeared.
69
In Playback mode, you can playback the already
recorded program but can not record any program.
Regardless of current broadcast program, you can
play back the recorded file in the File List.
To operate the Playback mode, you can select a program you want after pressing PLAY button.
1) Playback
If you press PLAY key on the RCU, then File List is
displayed in the top right corner. Then you can freely select and playback a file on screen after
pressing OK key on the RCU. While you are watching recorded channel, PLAY will be displayed in
the front panel by seven segment.
2) Slow playback
If you press PLAY key, the recorded program plays in normal speed and if you press PLAY key
again, it plays in slow speed.
3) FF, REW, Pause, Jump
If you want to playback the recorded program step by step, press PAUSE key repeatedly. If you
press F. F key repeatedly, the recorded program plays forward in x4, x8, x16 speed than normal
speed and, press REW key repeatedly, the recorded program plays backward x4, x8, x16 speed
than normal speed.
In addition, you can move fast to where you want to playback by press key on the RCU
when the info-bar is displayed on the screen.
If you press Stop button, it exits from Playback mode and goes to Live mode.
Playback mode
You can record your favorite program free from your
time and location and determine the start time of the
program independent of the broadcast time through
Timer Recording.
If you press MENU key in Live mode, you can select
Timer in the Menu. If you set the time and select On
or Off in record bar, then the timer recording is operated.
Time Recording
70
Also you can have same advantage as the Timer
recording through EPG Recording.
If you press EPG key on the RCU in Live mode, you
can select Program in EPG screen. If you press REC
key, then Dialogue Box pops up and you can change
start time, end time and file name. Then, if you press
OK key, EPG recording is operated. If EPG time precedes present time, recording starts coming out of EPG.
If you press PLAY key on the RCU in the live mode, the file list consisted of recording channel will
be displayed on the screen.
You can overview the recorded programs with
various file information and also you can be a program manager with operating several menu such as
Move, Lock, Rename, Delete and Format
In Live mode, if you press MENU key and select
Channel Manger -> HDD manger in the main menu,
file information such as Program name, Channel
name, Record time, File size, Duration and Free size
is displayed.
You can select one of Play, Lock, Move, Delete by press color hot key on the RCU ad if you press
MENU key on the RCU, additional box will be pop up so that you can select Format HDD, Repeat
mode and Shuffle Mode.
7-Segment Display
For your better convenience, HDD mode like Play, r-P is displayed as well in the 7-segment of
front panel during its operating.
EPG Recording
File List
HDD Manager
71
Receiver provides EPG function for you to get access
to the TV Guide(or Radio Guide if you are listening to
radio channels) which will give the titles of the current and next programs on different channels. The
information is only available from the network to
which the channel you are watching belongs.
Press EPG key on your RCU or select Program Guide
in the Main Page.
Then EPG box will be displayed.
You can see the channel list in the left side and
Program schedule for selected channel will be displayed in the right side. The time will be displayed
relating to the program schedule.
Select one channel and placing the mark on the time
of Program name which detail information you want
to know. Then you can see the program changes blue
color. And press OK key, then detail information box
will be displayed.
Note: A “No data available” message will be shown if the selected channel does not provide EPG
date.
EPG (Electronic Program Guide)
72
The “TIMER” function allows you program the timer with various ways. This function is one of the
strong point of Receiver.
To activate the “Turn on time” and/or “Turn Off the time”, Select YES and enter your desired time.
Note: The Receiver display the time which is given by Satellite, so it may be a some differences
between actual time and Receiver’s time.
Easy Timer
To activate the “Turn on time” and/or “Turn Off the
time”, select YES and enter your desired time.
And you can also select channel which will be turn
on or turn off.
Note: Easy timer is default for the first time.
Advanced Timer
Advanced Timer allows you to program the various
timer function.
You can set the timer daily, weekly, monthly and
yearly.
Timer
73
Although you entered correct value in Antenna Set up
menu, if your antenna is positioned incorrectly, you
could not receive signal form the Satellite.
So Receiver provides Antenna Positioning Help in
order for you to have exact information for the pointing of your antenna.
First select your desired Satellite name and then the
location of selected satellite will be displayed. In
case of that the location of the satellite is changed,
you can re-set up the new location.
Second, enter the value of Longitude and Latitude of
your location.
If you entered correct value of your position, place
your cursor on Compute and press OK key.
Then Receiver show the exact information of antenna
pointing.
Antenna Positioning Help
74
Front Panel Display
Trouble Shooting
UP LOAD PROCEDURE
DOWN LOAD PROCEDURE
ERROR IN DATA
TRANSMITTING
TV MODE
VCR MODE
SYSTEM WAITTING
FLASH ROM ERROR
SYSTEM BOOTING
Problem
The display on the front panel
does not light up.
No sound or picture, but thefront panel shows red light.
No sound or picture.
Possible causes
Main cable is not connected.
The Receiver is in standby
mode.
The satellite dish is not pointing at the satellite.
No signal or weak signal.
What to do
Check that the main cable is
plugged into the power
socket.
Press the standby button.
Adjust the dish. Check the signal level in the Antenna Setup
menu.
Check the cable connections,
LNB and other equipment
connected between the LNB
and the receiver, or adjust the
dish.
75
Trouble Shooting
Problem
Bad picture / blocking error.
No Welcome Menu on the
screen after you switched on
the Receiver for the first time.
The RCU is not working.
Possible causes
The satellite dish is not pointing at the satellite.
Signal is too strong.
Satellite dish is too small.
LNB noise factor too high.
The LNB is faulty.
The system is connected by
SCART leads and TV is not in
AV/EXT mode.
Battery exhausted.
RCU is incorrectly aimed.
What to do
Adjust the dish.
Connect a signal attenuator to
the LNB input.
Change to a larger dish.
Change to an LNB with lower
noise factor.
Change the LNB.
If the system is connected by
SCART leads, switch the TV to
the appropriate AV input.
Change the batteries.
Aim RCU at Receiver, or check
that nothing blocks the front
panel.
Note: If you have tried all of the actions suggested above, without solving the problem, please
contact your dealer or service provider.
Unsere HO
T- LINE: (D) 0190/512 532
(
DM 1,21/Min. ab 1.1.2002 € 0,62/Min.
)
(Österreich) 0900 400 222
(
ATS 8,80/Min. ab 1.1.2002 € 0,64/ Min.
)
Montag bis Donnerstag von 7.30 - 16.30 Uhr, am Freitag bis 15.15 Uhr
SM ELECTRONIC GmbH & Co. KG • Waldweg 2 • 22145 Stapelfeld/Hamburg
Internet: www.sm-electronic.de
E- Mail: info@sm-electronic.de
3974 11/01
Loading...