Page 1
1. INTRODUCTION
Model GBRK
Universal Garage Door
Keypad Control
Mounting
Accessories
Congratulations on your purchase of the Skylink® GBRK Universal
Garage Door Keypad Control. This is a kit with a universal keypad
transmitter and Smart ButtonTM. In this kit, you will find the following:
Keypad Transmitter
(Battery included)
Unplug the power cord of your garage door opener before installation to ensure
power is not connected.
DO NOT let children use the gargae door Transmitter without adult supervisor.
Children can injure themselves or others by the garage door.
DO NOT use remote to control the door without safety beams.
WARNING
1. Open up the “Easy ClipTM” and place it underneath
the existing 2 wires of the wall button / wall
console.
2. Ensure a pair of the wall button ribbon wires
are placed properly inside the channels of the
“Easy ClipTM”.
NOTE:
Ensure the ribbon wires
are not twisted but laid
flat inside the clip.
If your wall button ribbon wires
are not the same kind as shown
in the diagram, please refer
below (4) or visit our website
www.skylinkhome.com or
contact us for more information.
Easy Clip
TM
Ribbon Wires
Wall Button
Ribbon Wires
Press / lock
3. Press and lock the clip by
snapping it together. The
included Crimper helps you
lock the “Easy ClipTM”. Close
the cover and press down
to lock the cover using this
Crimper until you hear a “click”.
4. If the “Easy ClipTM” cannot clip with the wires from your wall button, cut
off the “Easy ClipTM” then connect two wires from the Smart Button
TM
GB-318 to the wall button.
a) Disconnect the existing wall button from the wall.
b) Connect the 2 wires from the Smart Button
TM
GB-318 to your existing wall button. Polarity does
not matter, so simply pick one wire from the Smart
ButtonTM GB-318 and connect it to one of the
screw terminals on your wall button. Connect
the 2nd wire to the other screw terminal.
c) Reconnect the wall button back.
2. RECEIVER INSTALLATION
Rating of the transformer:
12V DC, 100mA
Diameter of DC plug : 3.5mm
7. Secure the Smart ButtonTM GB-318 properly with the mounting accessories.
Note: Do not cut the antenna! Straighten up the antenna to improve
signal reception.
5. If the wall button wires are hidden inside the
wall, please connect the “Easy ClipTM” to
the exposed wires attached to the
terminals of the garage door
opener.
Note: After installation of the “Easy Clip
TM
”, if you want to re-install the
Smart Button
TM
GB-318 to another place, please open the “Easy Clip
TM
” by
gently unlocking the two buckles with a screw driver, and remove it from
the wires. Do not re-use the “Easy Clip
TM
”, refer to Step 4 to re-install it.
6. Power up the garage door opener, the red LED on the Smart Button
TM
GB-318 should keep flashing slowly within 2 minutes.
2. RECEIVER INSTALLATION (CONT)
If the Smart Button
TM
GB-318’s red LED does not flash after the
Smart ButtonTM GB-318 has been connected to the wall button’s
wires for 2 minutes, your garage door opener is probably too
old. However, the Smart ButtonTM GB-318 will still work if you
plug in an adapter (purchased separately). Please
contact Skylink® to purchase the adapter.
Antenna
You need to do the programming in order to add the transmitter to a receiver.
3. PROGRAM KETPAD TRANSMITTER G6K TO RECEIVER GB-318
Smart ButtonTM GB-318 can learn up to 10 remote controls.
To add remote controls, follow the instructions below:
1. Press the learn button on the side of the Smart Button
TM
GB-318.
2. Once the learn button is pressed, the LED will
flash quickly. Release the learn button.
3. Enter [PIN][#][assigned number of door] on the
keypad transmitter you would like to program.
The assigned door number can be either
1, 2, 3, or 4.
4. Once the keypad transmitter is programmed, the
LED will flash slowly, in the same way as it
flashes in standby mode.
5. You may now operate the garage door opener
with this new keypad transmitter.
Learn
Button
Smart Button
TM
GB-318
If the red LED flashes slowly, the Smart Button
TM
GB-318
is in standby mode. When a valid remote control signal is
received, it will open / close the garage door.
Press the programmed button on the remote control
or Smart Button
TM
GB-318, it will open / close the
garage door.
Note: After connecting this NEW Remote Control to
your wall button, your existing remote control will still
work with this connection.
OPEN /
CLOSE
Button
4. OPERATION
LED
LED
Crimper
Double Sided Tape
Garage Door
Receiver
Smart Button
TM
GB-318
Page 2
9. WARNING
DO NOT let children use the garage door transmitter without adult supervision.
Children can injure themselves or others by the garage door.
7. BATTERY
CUSTOMER SERVICE
17 Sheard Avenue, Brampton, Ontario, Canada L6Y 1J3
Email:support@skylinkhome.com
http://www.skylinkhome.com
P/N. 101Z769-002
Patent pending
® are registered trademarks of their respective corporations
©2010 SKYLINK GROUP
11. WARRANTY
If, within one year from date of purchase, this product should become defective
(except battery), due to faulty workmanship or materials, it will be repaired or
replaced, without charge. Proof of purchase and a Return Authorization are required.
12. CUSTOMER SERVICE
You can add up to 10 additional transmitters to control the same receiver.
Skylink® offers Keychain Transmitters and Visor Transmitters to work
with your receiver. For more information,
please visit our website at
www.skylinkhome.com
or contact us.
8. ADDITIONAL TRANSMITTER
Two 3 volt Lithium type (CR2032) batteries (included).
It is time to change the batteries when the backlight no longer appears.
Battery
Compartment
+
-
10. FCC
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that
may cause undesired operation.
WARNING:
Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
4. OPERATION (CONT)
If you do not hear 3 beeps after entering the PIN, i.e. [0 0 0 0][#][1], that
means you have entered an incorrect PIN, and the keypad transmitter will
not operate your garage door.
The keypad transmitter can operate up to 4 Smart Button
TM
units, that also
means one keypad transmitter can operate up to 4 garage door openers.
Same PIN will be used for all doors. The factory default password is [0 0 0 0].
To operate door 1, you will enter [0 0 0 0][#][1]
To operate door 2, you will enter [0 0 0 0][#][2]
To operate door 3, you will enter [0 0 0 0][#][3]
To operate door 4, you will enter [0 0 0 0][#][4]
To program the keypad transmitter into the Smart ButtonTM, you must
decide which door you need to operate. If you only have one Smart
ButtonTM, we suggest you to use door 1. i.e. [0 0 0 0][#][1].
Follow the instructions below to change the PIN.
To change your PIN:
1. Enter the current PIN, (factory default PIN 0 0 0 0), press * .
2. Enter new 4 to 6 digit PIN, press * .
3. Enter new PIN again, press * .
For example, if you are changing the PIN number from 0000 to 123456,
enter the following sequence, 0000, *, 123456, * , 123456, * .
If confirmed, the backlit LED flashes and the unit emits a long beep.
If you would like to
- find out the up-to-date specifications
- know more about features and applications
- download documents, i.e. user’s instructions
- order Skylink products
or if you have difficulty getting products to work, please:
1. visit our FAQ section at www.skylinkhome.com, or
2. email us at support@skylinkhome.com, or
3. call our toll free at 1-800-304-1187 from Monday to Friday, 9 am to 5 pm EST.
Fax (800) 286-1320
To erase unwanted remote control(s) from the memory of Smart Button
TM
GB-318, first erase all remote controls, then learn the one(s) you would
like to keep, follow the steps below:
1. Press and hold the learn button for approximate 10 seconds.
2. The LED will flash rapidly after 10 seconds to indicate all the programmed remote controls have been erased. You may now release
the learn button.
3. You have erased all the remote controls programmed to the Smart
Button
TM
GB-318.
5. ERASE TRANSMITTERS
6. TROUBLE SHOOTING
Q: What can I do if the door opener does not react after I press the button on
the transmitter ?
A: - Ensure when the button on the transmitter is pressed, the red LED on the
transmitter comes on. Otherwise, check if the battery is inserted properly.
- Make sure the correct button on the transmitter is pressed.
- Ensure the wires that were previously connected to the wall mounted
door control are not loose.
- Ensure the transmitter has been programmed to the receiver. Refer
to section 3 for how to program a transmitter to the receiver.
Loading...