SkyLink GB-318 User Manual
Smart Button
TM
Garage Door Receiver
1. INTRODUCTION
Model GB-318
2. INSTALLATION (CONT)
Congratulations on your purchase of the Skylink® Smart ButtonTM. The
Smart Button
TM
is designed to work with Skylink® remote control G6M,
G6K, G6V, G6T3 , SkylinkhomeTM system remote, and more to operate the
Garage Door Opener. In this kit, you will find the following:
Mounting Screws
and anchors
Smart Button
GB-318
TM
Double Sided Tape
Crimper
2. INSTALLATION
Unplug the power cord of your garage door opener
WARNING
before installation to ensure power is not connected.
TM
Easy Clip
1. Open up the “Easy ClipTM” and place it underneath
the existing 2 wires of the wall button / wall
console.
2. Ensure a pair of the wall button ribbon wires
are placed properly inside the channels of the
“Easy ClipTM”.
Wall Button
NOTE:
Ribbon Wires
Ensure the ribbon wires
are not twisted but laid
flat inside the clip.
Press / lock
If your wall button ribbon wires
are not the same kind as shown
in the diagram, please visit our
website www.skylinkhome.com
Ribbon Wires
or contact us for more information.
3. Press and lock the clip by snapping it together. The included Crimper
helps you lock the “Easy ClipTM”. Close the cover and press down to
lock the cover using this Crimper until you hear a “click”.
4. If the “Easy ClipTM” cannot clip with the wires from your wall button, cut
off the “Easy ClipTM” then connect two wires from the Smart Button
TM
to the wall button.
a) Dismount the existing wall button from the wall.
b) Connect the 2 wires from the Smart Button
TM
GB-318 to your existing wall button. Polarity
does not matter, so simply pick one wire from
the Smart ButtonTM and connect it to one of the
screw terminals on your wall button. Connect
the 2nd wire to the other screw terminal.
c) Mount the wall button back.
5. If the wall button wires are hidden inside the
wall, please connect the “Easy ClipTM” to
the exposed wires attached to the
terminals of the garage door
opener.
6. Power up the garage door opener, the red LED on the Smart Button
GB-318 should keep flashing slowly within 2 minutes.
If the Smart ButtonTM GB-318’s red LED does not flash after the Smart
ButtonTM GB-318 has been connected to the wall button’s wires
for 2 minutes, your garage door opener is probably too old.
However, the Smart ButtonTM will still work if you plug in an
adapter (purchased separately). Please contact
Skylink® to purchase the adapter.
Rating of the transformer:
12V DC, 100mA
Diameter of DC plug : 3.5mm
7. Secure the SmartButtonTM GB-318 properly with the mounting accessories.
Note: Do not cut the antenna! Straighten up the antenna to improve
signal reception.
Note:
After installation of the “Easy Clip
TM
Button
GB-318 to another place, please open the “Easy Clip
unlocking the two buckles with a screw driver, and remove it from the
wires. Do not re-use the “Easy Clip
TM
”, if you want to re-install the Smart
TM
”, refer to Step 4 to re-install it.
TM
” by gently
3. OPERATION
If the red LED flashes slowly, the Smart Button
TM
GB-318
is in standby mode. When a valid remote control signal is
received, it will open / close the garage door.
Press the programmed button on the remote control
or Smart Button
TM
GB-318, it will open / close the
garage door.
LED
OPEN /
CLOSE
Button
Programming
Learn additional remote controls
Smart ButtonTM GB-318 can learn up to 10 remote controls.
To learn additional remote controls, follow the
instructions below:
1. Press the learn button on the side of the GB-318.
2. Once the learn button is pressed, the LED will
flash quickly. Release the learn button.
LED
3. Within 30 seconds, press the button on the remote
control you would like to program.
4. Once the remote control is programmed, the LED
will flash slowly, in the same way as it flashes
in standby mode.
5. You may now operate the garage door opener
Learn Button
with this remote control.
Erase remote controls
To erase unwanted remote control(s)from the memory of Smart Button
GB-318, first erase all remote controls, then learn the one(s) you would
like to keep.
To erase remote control(s), follow the steps below:
1. Press and hold the learn button for approximate 10 seconds.
2. The LED will flash rapidly after 10 seconds to indicate all the pro-
grammed remote controls have been erased. Release the learn button.
3. You have erased all the remote controls programmed to the Smart
Button
TM
GB-318.
TM
TM
4. ADDITIONAL TRANSMITTER
You can add up to 10 additional transmitters to
control the Smart ButtonTM GB-318. Skylink
®
offers different lighting control / automation
transmitters, Visor Transmitters, Keychain
Transmitters and Keypad Transmitters
to work with your receiver. For more
information, please visit our website
at www.skylinkhome.com or contact us.
5. WARNING
DO NOT let children use the garage door transmitter without adult supervision.
Otherwise, Children and others may be injured by the garage door.
6. FCC
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) This device must accept any interference
received, including interference that may cause undesired operation.
WARNING:
Changes or modifications to this unit not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more o f the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
7. WARRANTY
If, within one year from date of purchase, this product should become defective
(except battery), due to faulty workmanship or materials, it will be repaired or
replaced, without charge. Proof of purchase and a Return Authorization are required.
8. CUSTOMER SERVICE
If you would like to
- find out the up-to-date specifications
- know more about features and applications
- download documents, i.e. user’s instructions
- order Skylink products
or if you have difficulty getting products to work, please:
1. visit our FAQ section at www.skylinkhome.com, or
2. email us at support@skylinkhome.com, or
3. call our toll free at 1-800-304-1187 from Monday to Friday, 9 am to 5 pm EST.
Fax (800) 286-1320
CUSTOMER SERVICE
17 Sheard Avenue, Brampton, Ontario, Canada L6Y 1J3
Email:support@skylinkhome.com
http://www.skylinkhome.com
P/N. 101Z703
Patent Pending
® are registered trademarks of their respective corporations
©2010 SKYLINK GROUP
V1.9
Loading...