SkyLink BEETLE WMR-100 User Manual

1

SKYLINK BEETLE

User Manual

2

Welcome

Thank you for purchasing Skylink BEETLE for Skylink CDMA Broadband Network!

Before using the Skylink BEETLE, please read this user manual, which outlines the

features and functions of the Skylink BEETLE.

This device operates over the high-speed Skylink networks in the 450MHz band and

Wi-Fi enabling you to connect several devices to the internet and Wi-Fi-enabled devices

anywhere! 



Customerservice 

For customer service, contact at [e-mail].

Address : WeTelecom Co., Ltd.

The’O Plus #1604

Sanbon-dong, Gunpo City, Kyunggi-do, KOREA

Phone : [phone]

Limitation of Liability

The information contained in this document is subject to change without notice and

should not be construed as a commitment by Skylink.

Copyright

©2011 WeTelecom Co., Ltd.

3

Contents

1 Before using the Skylink BEETLE .............................................................................................................. 6

Important Notice ................................................................................................................................................ 6

Battery Use and Removal ............................................................................................................................... 6

Safety Hazards ..................................................................................................................................................... 7

The Skylink BEETLE Package .......................................................................................................................... 8

2 Overview : Skylink BEETLE ........................................................................................................................... 9

Introduction .......................................................................................................................................................... 9

Features................................................................................................................................................................... 9

About the Skylink BEETLE Mini Hotspot ............................................................................................... 10

3 Getting Started ............................................................................................................................................... 12

Quick Start Procedure ................................................................................................................................... 12

NetKit Installation for Windows® OS .................................................................................................... 13

NetKit Installation for MAC® OS ............................................................................................................. 13

Minimum System Requirements............................................................................................................... 14

Power Source and Battery Charging ...................................................................................................... 15

LED States ........................................................................................................................................................... 15

How to insert RUIM Card, Battery, and Charge the Battery ........................................................ 16

Powering the Skylink BEETLE On and Off ............................................................................................ 18

Choose between Wi-Fi mode and USB Modem Mode ................................................................. 18

4 Wi-Fi Mode Connection for the First time. ..................................................................................... 19

Browser Interface ............................................................................................................................................. 19

How to Connect to the Skylink BEETLE ................................................................................................. 19

Open the Browser Interface ........................................................................................................................ 21

Home Screen ..................................................................................................................................................... 22

5 Basic Settings in Wi-Fi Mode .................................................................................................................. 24

Setup Wizard ..................................................................................................................................................... 24

4

WWAN Settings ............................................................................................................................................... 24

Temporary Hotspot ........................................................................................................................................ 26

6 Advanced Settings in Wi-Fi Mode ....................................................................................................... 28

Internet Settings .............................................................................................................................................. 28

Wireless Settings .............................................................................................................................................. 29

Firewall ................................................................................................................................................................. 30

Traffic Control ................................................................................................................................................... 32

Utility ..................................................................................................................................................................... 34

Administration................................................................................................................................................... 36

Status .................................................................................................................................................................... 37

7 USB Modem Mode Connection for the First Time ..................................................................... 39

NetKit Installation and Uninstall (Windows® XP) ............................................................................ 39

NetKit Installation and Uninstall (Windows® Vista (or 7)) ........................................................... 43

8 Descriptions of the NetKit GUI in USB Modem Mode ............................................................. 47

Launch the NetKit ........................................................................................................................................... 47

Interface overview ........................................................................................................................................... 47

9 Internet Services in USB Modem Mode ............................................................................................ 48

Accessing the Internet .................................................................................................................................. 48

History Information ........................................................................................................................................ 48

10 SMS Service in USB Modem Mode ................................................................................................... 49

Creating and sending a Message ............................................................................................................ 49

Inbox ..................................................................................................................................................................... 49

Outbox.................................................................................................................................................................. 50

11 PhoneBook in USB Modem Mode ..................................................................................................... 51

Creating a Contact .......................................................................................................................................... 51

Editing a Contact ............................................................................................................................................. 51

Deleting a Contact .......................................................................................................................................... 51

5

Searching a Contact ....................................................................................................................................... 51

Sending a message ........................................................................................................................................ 52

12 Settings and Information in USB Modem Mode ....................................................................... 53

Version Information ........................................................................................................................................ 53

Unlocking the PIN ........................................................................................................................................... 53

Selecting a PPP mode ................................................................................................................................... 53

Enable / Disable PIN ...................................................................................................................................... 54

Change PIN Code ............................................................................................................................................ 54

Selecting Always On Top mode ............................................................................................................... 54

Selecting a Pref Mode ................................................................................................................................... 55

Selecting a language ..................................................................................................................................... 55

13 How to Mac OS in USB Modem Mode ........................................................................................... 56

14 Trouble Shooting ........................................................................................................................................ 57

Reset and Factory Reset ............................................................................................................................... 57

15 Product Specification ................................................................................................................................ 59

Technical Specification .................................................................................................................................. 59

6

1 Before using the Skylink BEETLE

Important Notice

1. When connecting the device to Notebook only with USB Data Cable may cause

more consumption of Notebook’s battery.

2. Using the device for a long time may cause over heating problem, please be

careful. Always try to turn off the power if not in use.

3. Do not forcefully open, fix, or assemble the device; please visit assigned service

center for repair.

4. Be careful not to damage RUIM Card. Inside of RUIM Card, data are stored to

initiate the device and if it is damaged the device may not work.

5. When the device is connected to PC/Notebook do not logout by irregular

method, there might be some abnormal packet data in PC/Notebook. Logout by

normal procedure.

6. Protect the Skylink BEETLE from liquids, dust and excessive heat.

7. Store the Skylink BEETLE in a safe place, when not in use.

8. Turn the power off and remove the battery from device when not in use if

possible.

9. Due to the transmission and reception properties of wireless communications,

data can occasionally be lost or delayed. This can be due to the variation in radio

signal strength that results from changes in the characteristics of the radio

transmission path. Although data loss is rare, the environment where you operate

the Skylink BEETLE may adversely affect communications.

Skylink or its partners will not be held responsible for damages of any kind

resulting from the delays or errors in data transmitted or received with the

Skylink BEETLE device, or failure of the Skylink BEETLE device to transmit or

receive such data.

Battery Use and Removal

1. Never expose batteries to temperatures below -10°C (14°F) or above 45°C

(113°F). For example, never leave the device in a car.

2. Always use Skylink BEETLE’s original battery and charger.

7

3. Do not disassemble/open, crush, or make hole/holes.

4. Do not expose to water or other liquids, expose to fire, explosion, or other

hazardous items.

5. Do not short circuit a battery.

6. Do not contact metallic or conductive object to the battery terminals.

7. Use only genuine battery from Skylink when replacing. Using unreliable battery

may cause a risk of fire, explosion, leakage, or other hazard.

8. When charging the battery, keep it near room temperature.

Safety Hazards

Please do not operate the Skylink BEETLE device in any environment that may be

susceptible to radio interference resulting in danger specifically;

Areas where prohibited by the law

 Follow any special rules and regulations and obey all signs and notices.

Always turn off the host device and remove the modem from the USB port

when instructed to do so, or when you suspect that it may cause

interference or danger.

Where explosive atmospheres may be present

 Do not operate the Skylink BEETLE in any area where a potentially explosive

atmosphere may exist. Sparks in such areas could cause an explosion or fire

resulting in bodily injury or even death. Be aware and comply with all signs

and instructions.

 Users are advised not to operate the Skylink BEETLE while at a refueling

point or service station. Users are reminded to observe restrictions on the

use of radio equipment in fuel depots (fuel storage and distribution areas),

chemical plants or where blasting operations are in progress.

 Area with a potentially explosive atmosphere are often but not always clearly

marked. Potential locations can include gas stations, below deck on boats,

chemical transfer or storage facilities, vehicles using liquefied petroleum gas

(such as propane or butane), areas where the air contains chemicals or

particles, such as grain, dust or metal powders, and any other area where

you would normally be advised to turn off your vehicle engine.

Near Medical and life support equipment

 Do not operate the Skylink BEETLE in any area where medical equipment,

life support equipment, or near any equipment that may be susceptible to

8

any form of radio interference. In such areas, the host communications

device must be turned off. The Skylink BEETLE may transmit signals that

could interfere with this equipment.

On an aircraft, either on the ground or airborne

 Many airline regulations state that you must suspend wireless operations

before boarding an airplane. Please ensure that the host device is turned

off and the Skylink BEETLE is removed from the USB port prior to boarding

aircraft in order to comply with these regulations. The Skylink BEETLE can

transmit signals that could interfere with various onboard systems and

controls.

While operating a vehicle

 The driver or operator of any vehicle should not operate a wireless data

device while in control of a vehicle. Doing so will detract from the driver or

operator’s control and operation of that vehicle. In some countries,

operating such communications device while in control of a vehicle is an

offense.

The Skylink BEETLE Package

The Skylink BEETLE package includes:

- Skylink BEETLE Mini Hotspot

- Lithium Ion Battery

- AC Travel Adaptor (T/A)

- MicroUSB Data Cable

- User Manual CD

9

2 Overview : Skylink BEETLE

Introduction

Skylink BEETLE is a mini mobile Hotspot, enabling you with high-speed data access

through CDMA wireless broadband data network and Wi-Fi connectivity anywhere.

Skylink BEETLE offers you more freedom than ever before. The device is a truly wireless

that can work without any cables and less hassle with Software.

Features

 Possible to connect the Internet by 1x EV-DO Rev. A, High speed

Wireless Broadband Data Network.

 Choose between Two operating mode :

Wireless data networking with Wi-Fi or USB Cable

- Single user: One can use it with USB data cable as Modem mode or

without data cable as Wi-Fi mode.

- Multiple users: Use as Wi-Fi mode.

- The Skylink BEETLE package includes a battery to work on both Wi-Fi

mode and USB Modem mode.

- When using as USB Modem mode, the driver and “NetKit” program will

automatically installed into PC/Notebook.

 Using as Wi-Fi Mode

- Multiple users can access the Internet and exchange e-mails at the same

time.

- Possible to connect to Wi-Fi devices: Such as Notebooks, Desktops,

Tablet PC, Smartphone, PDA (Personal Digital Assistants), and consumer

devices that supports Wi-Fi.

- Since the device is equipped with latest Wi-Fi Router chipset, it supports

Wi-Fi 802.11 b/g/n technology.

10

 Using as USB Modem Mode

- By using NetKit program, it easily connects to the Internet.

- Driver and NetKit program will automatically be installed. Supported OS

are Windows XP, Vista, Windows 7 and Mac OS (check the version)

 VPN Capability
 SMS supported

About the Skylink BEETLE Mini Hotspot

1. Power Button and Status Indicators

- Indicates power, battery and CDMA communication activities.

- Please refer to the Power Button LED status page. (See page 14 for

Power Button LED description)

2. Wi-Fi Router Status Indicator

- Indicates Wi-Fi Router status. (See page 14 for Wi-Fi Router Status

Indicator LED description)

3. External Antenna Connector

- Enable you to use external antenna for better signal reception. (External

antenna is not included in the package.)

1

2

3 4

11

4. MicroUSB Connector

- Connects to desktops/notebooks with a Type A USB port.

5. Factory Reset button

- Resets the device to initial factory settings.

6. RUIM Card Slot

- RUIM card is inserted here.

7. Battery Compartment

- Battery is inserted here.

5

6

7

12

3 Getting Started

Hope this will help you to guide and to get started with the Skylink BEETLE in this

chapter. There are two modes in the Skylink BEETLE Mini Wi-Fi Router, one is Wi-Fi and

the other is USB Modem.

Quick Start Procedure

Before you begin with Skylink BEETLE, please follow few steps:

1. Check to make sure your computer meets the minimum system requirements.

(See page 14 for Minimum System Requirements.)

2. Slide to open the battery cover at the bottom of the device.

3. Insert RUIM card that provided by service provider to RUIM slot.

4. Insert a charged battery.

5. Connect the AC Travel Adaptor to the device and charge it for 3 hours before

using the device.

6. Choose between either Wi-Fi Mode or USB Modem mode.

- When multiple users are using, choose Wi-Fi mode.

- When single user is using, choose USB Modem mode or Wi-Fi Mode

7. Using as Wi-Fi mode for the first time,
① Press the Power button on Skylink BEETLE, shortly. The Power button LED

and Wi-Fi LED will flash.

② Use Wi-Fi manager on your computer to locate the Skylink BEETLE Wi-Fi

network.

③ Find “WMR-100AP_XXXXXX” network in the list of available wireless

networks and click “Connect”.

④ From your computer’s Web browser, enter http://192.168.0.254

into the

address window and press the Enter or Return key.

⑤ Enter the id & password “admin”, “admin” when requested.
⑥ Using for the first time, Setup Wizard will launch on the screen. It will

guide you through setting up security of your device.

13

⑦ Follow the instructions on the screen.
⑧ After you click “Done”, your device will start.

For more details and information on Wi-Fi mode connection, please refer

sections from “4. Wi-Fi Mode Connection for the first time

” to “6.

Advanced Setting in Wi-Fi Mode”.

8. Using as USB Modem Mode for the first time,
① Plug USB data cable into Skylink BEETLE and USB port on your computer.

The device will be power on automatically. The Power button LED will

light on but the Wi-Fi status LED will not lit.

② Launch NetKit software for either Windows OS or Mac OS as follows.

 NetKit Installation for Windows® OS

i. If USB DRIVER is not present, Modem package Installer will

run automatically.

Tip

If Modem package Installer doesn’t work automatically, Execute RunPack.exe

manually.

ii. Select the desire language and press “OK”. Welcoming

message for using NetKit Program window will be shown.

iii. Press “Install” button. The program starts automatically.
iv. Press “Finish” button once it is done with program

installation.

v. It will now start to install the USB driver. Please check

whether the driver has been installed properly by checking

<Device Manager>.

 NetKit Installation for MAC® OS

i. Plug the Skylink BEETLE in USB port on MAC.

14

ii. Open SkyLink CD, start mintechUSBCDC and install MAC

Drivers. Restart MAC.

iii. Execute any connection manager for Skylink BEETLE Mobile

Products.

iv. Enter the User ID, Password and Number in Network

Preference, and connect Internet.

For more details and information for USB Modem mode connection, please

review section from “7. USB Modem Mode Connection for the First Time

”

to “13.How to Mac OS in USB Modem Mode

”.

Minimum System Requirements

1. PC Hardware

- Recommend to use PC/Notebook at speed of 300 MHz or higher.

- Wireless LAN is essential. Recommending 802.11 b/g/n 2.4GHz.

- Minimum 233 MHz speed required

* Intel Pentium/Celeron products, AMD K6/Athlon/Duron products or compatible

processors

- Recommend to use 128MB RAM or higher

- At least 100 MB of free hard disk space is required.

- Motherboard or PCI card that supports USB.

- Video adaptor with Super VGA (800 x 600) or higher resolution and Monitor

- CD-ROM or DVD Optical Drive

- Keyboard and Mouse

2. Operating System

- Windows® XP Home or Professional ( with Service Pack 2 )

- Windows® 2000 (with Service Pack 4 for optimal performances)

- Windows® Vista 32bits/64bits

- Windows® 7 32bits/64bits

- Mac OS 10.4 or higher

15

< Recommended parameters >

Windows Update : Keep your computer up to date

Power Source and Battery Charging

There are three power sources that Skylink BEETLE may use.

- Battery

- AC Travel Adaptor

- USB Data Cable

User must press Power button to turn on the device even though the Battery and AC

Travel Adaptor are connected. If USB cable is connected between the device and

PC/notebook, the device will be turned on automatically without pressing the Power

button.

When Power button is not pressed, then battery will be charged only through either USB

Cable or AC Travel Adaptor.

LED States

 Wi-Fi Router Status LED

LED Status Status information

LED not lit No Power (Wi-Fi mode off)

LED Green Solid Wi-Fi Powered

LED Green Blink Wi-Fi transmitting and receiving data;

Blinking rate proportional to data speed

16

 Power Button LED

LED Status Status information

LED not lit No Power

LED RED Solid Power ON

LED RED Blink Low Battery warning

LED Green Solid Service Available

LED Green Blink Service Not Available

LED Blue Solid Connected to EVDO

LED Blue Blink Connected to 1x

LED Orange Solid Charging

LED Orange Blink Fully Charged

How to insert RUIM Card, Battery, and Charge the Battery

For first time use of Skylink BEETLE Mini Hotspot, we recommend to follow below

sequences.

Note

Before using the Skylink BEETLE Mini Hotspot for the first time, please

insert RUIM card and fully charged battery.

1. Open the battery cover, which located in the bottom of the device

17

2. Insert RUIM Card that provided by the service provider. See the below

picture for more detail.

3. Insert the battery by lining up battery contact point with the gold contact

points.

4. Once the battery is securely settled, put the battery cover back into the

device until it locks firmly.

18

5. Plug the AC travel adaptor into the proper electrical outlet and connect

MicroUSB port of the AC travel adaptor to the MicroUSB port of the

device. Charge the battery for at least three hours.

Powering the Skylink BEETLE On and Off

To power the device on:

Press the Power button until the Power LED lights up solid red.

And solid green LED indicates the device is in service area and ready to connect.

(Press Power button for two to three seconds to power on)

To power the device off:

Press the Power button until the Power LED shuts off.

(Press Power button for two to three seconds to power off)

Choose between Wi-Fi mode and USB Modem Mode

When setup is completed, you can choose one of two modes : Wi-Fi mode or

USB Modem mode.

Note

Pressing Power button, the device will automatically connected to Wi-Fi

mode if MicroUSB Data Cable is not connected.

19

4 Wi-Fi Mode Connection for the First time.

Browser Interface

Skylink BEETLE uses a browser interface to configure the device.

The browser interface lets you:

 View the status aspects of your network.
 Set up wireless security, including MAC, port filtering and Port forwarding.
 Set up a temporary hotspot to allow a maximum of five connections to your

device without having to share your network name and network key.

How to Connect to the Skylink BEETLE

1. Insert RUIM Card and Battery with AC Travel Adaptor

2. Press Power button to connect to Wi-Fi mode .

3. Use your default Wi-Fi manager to locate the Skylink BEETLE wireless network.

Tip

The Steps of connecting to a Wi-Fi network vary depending on your operating

system whether you use the native application or third-party software.

Generally you click an icon (often in the Windows notification area or System

Preferences>Network on a Mac) where you can select “View Available Wireless

Networks.” If you are unfamiliar with wireless networking on your computer,

consult the computer help system.

4. If multiple wireless networks are found, highlight the one that indicated as “WMR-

100AP_XXXXXX” in its name.

5. Click Connect.

6. If this is your first time connecting to the Skylink BEETLE, continue with these steps.

20

7. At computer’s Web browser, type http://192.168.0.254 into the address window and

press Enter or Return key.

8. Enter id & password as “admin”, “admin” when requested.

9. A Setup wizard will launch and guide you through setting up security sequences for

your device.

Important

Be sure to write down both the administrative password and the network

key which you created from the initial Setup wizard.

If you cancel the wizard, your network will be left unsecure (open).

10. Follow the instructions on the screen as shown:

- Choose one from 3 different connection mode, “Auto”, “Manual” and “On Demand”.

- Click “Next” button.

21

- Choose “Authentication” and “Preferred Mode”.

- Press “Next” button.

Important

To secure your personal information/files and virus attack, it is a must to set

“Security Mode” with password.

- Change “Network Name(SSID)” as you desire.

- It is strongly recommended to check “Enable” box and to write “Pass Phrase”.

“Pass Phrase” is your password.

11. After you click “Done”, your device will start.

Open the Browser Interface

1. Open your Web browser and type http://192.168.0.254 into the address window.

2. Type in the administrative password into the Login Popup window and press Enter key.

Important

If this is the first time you are entering the browser interface or if you have

used the factory reset button, it is absolutely recommended to start Setup

Wizard.

22

3. Home Screen will open.

Home Screen

Home screen is the first screen you see after logging in to the browser interface. It is the

main point of entry for all your work in the browser interface.

1. Status Bar

Status bar runs horizontally along top of the browser interface.

It displays information about the device as shown below.

From the left is Signal Strength, Service status, Connection status, RUIM status, Battery

level.

2. Internet Connection

Internet connection tells :

23

 The number of bytes received and transmitted
 Duration of the current connection
 IP address and Subnet Mask for the device

3. Wi-Fi

Wi-Fi section tells:

 The Radio Status
 The network mode
 The network name (SSID)
 The Security Status

To change Wi-Fi settings, use the Wireless Settings Menu in Advanced settings.

24

5 Basic Settings in Wi-Fi Mode

Minimum settings for using Skylink BEETLE.

Setup Wizard

For minimum settings of Skylink BEETLE, use default settings.

Just follow the instructions in the display.

Setup wizard starts automatically when SKYLINK BEETLE device is used for the first

time through the Browser. User can access it later from the menu.

WWAN Settings

Basic settings for connecting to 3G network.

1. RUIM Status

PIN Lock : Indicates RUIM Lock Status.

PIN Count : Indicates the number of PIN Verification attempts. 3 attempts are possible

for PIN Verification. If failed after 3 tries, RUIM card will be blocked. To reuse the

card, one must enter the validated Unblock code. Unblock code can be tried for upto

10 times.

Note

Pin, Unblock code is on the RUIM card.

Important

If RUIM card gets Locked or Blocked, Web UI shows a warning message

window. In such case, move to WWAN Settings menu and execute either

PIN Verification or Unblock code verification

25

2. RUIM Settings

Menu for setting RUIM

PIN Mode : Setting RUIM security. For configuring, it requires to enter PIN.

 Verification : When in Locked position, one must enter Valid PIN code to

complete the verification which enables to use RUIM. Setting is required when

reboot.

 Unlock : When Unlock is selected, RUIM security will be released and it will be

always in useable state

 Lock : By selecting RUIM Security Lock, one must go through PIN verification

to use it.

 Change : To change PIN code.
 Unblock : If PIN code failed after 3 attempts, card will be blocked. To unblock

the card and set a new PIN, one must enter the Unblock code. When Unblock

code is properly inserted the device will reboot and RUIM stays in a Locked

position.

PIN Code : Setting PIN code.

3. WWAN Connection Mode

Setting 3G connection mode

On Demand : User trying to access the Internet when the device is connected to Wi-Fi

network, it will automatically connects to 3G. If the device is not in use for designated

idle time, then it will automatically disconnected.

Auto : If user connects to Wi-Fi network, the Skylink BEETLE will connect to 3G network

and waits.

Manual : User can choose connect/disconnect as needed in the Web interface.

26

4. WWAN Connection Information

Setting parameters to connect to 3G. User can change contents as needed.

User name, Password, Service Number

Authentication: PPP Authentication Mode

System Selection: Setting 3G network

5. Wi-Fi Settings

Wi-Fi Security settings and change SSID

SSID : Wi-Fi network name. You can change the name of network to more informative to

you.

Security: Selecting Security settings. If not selected, Wi-Fi network becomes unsecure.

When enabled, must setup a password.

Pass Phrase: Pass code or password used to access the network. The default value is

WPA2-PSK.

Temporary Hotspot

This Function allows you to set up a temporary hotspot for multiple users in your

working area (maximum of five) to go online at the same time.

It generates a temporary network name and network key to allow multiple users to

connect to your device without having to change the security settings on your secure

profile.

To set up the temporary hotspot

27

1. From the Menu, select “Temporary Hotspot”.

You will see a new (temporary) network name (SSID) and network key. In the example

shown above, the temporary network name is “WMR-100_638p” and the temporary

network key is “br7ecsrf”.

2. Click Apply. Members of your workgroup can now use the temporary network name

and network key to connect to your device.

Tip

Make sure “Enable” check box is selected to create a new network name and

network key.

28

6 Advanced Settings in Wi-Fi Mode

Menu for expert users.

Internet Settings

This screen allows you to view the local (WLAN) IP address and the MAC address of your

device.

1. IP Settings

LAN Setup/ DHCP Server

From this menu, it shows following (possible to make changes for your device):

 Local IP address
 Subnet mask
 MAC address of the device (Read Only)
 DHCP address range used by the device’s DHCP server

The IP address and subnet mask can be altered by entering new numbers and pressing

Apply button. If you have devices with local static IP addresses, these addresses should

not be within the DHCP range.

If all clients in the Network use static IP, the user can disable DHCP server.

When setting DHCP range, End IP address value must be larger than Start IP address.

UPNP

UPnP(Universal Plug and Play) is a protocol in Window’s Software that searches for

available router and make sure multiple server programs operate normally. To use UPnP,

select enable then press Apply button. When UPnP is in operation, Window recognizes it

as internet gateway.

29

Wireless Settings

This menu is for setting Wi-Fi.

Following information is available and can be configured.

 Current wireless mode.
 SSID
 Security type and encryption
 Network Key
 WPS Function

1. Basic

You can configure the minimum settings of Wireless, such as Network Name (SSID),

Network Mode and Channel. Once they are set, the Hotspot can be accessed.

Radio On/Off : Wi-Fi RF ON/OFF

Network Mode : User can choose network mode. The default setting for Skylink BEETLE

is to support all 802.11b/g/n modes. Choose the correct settings on the client’s network

card for proper connection.

SSID : Wi-Fi network name. You can assign a name to distinguish with other router

devices.

Broadcast Network Name : enable/disable. Your SSID will broadcasted.

Frequency (Channel) : It is strongly recommend to use the default values.

TX Power : 0, 25, 50, 75, 100%. User can change TX power based on distance from Base

Station or environment.

Note

Very careful with disabling “Broadcast Network Name”.

If you checked “disable” box of “Broadcast Network Name”, then you cannot

access to your AP. If you really want to disable Broadcast Network Name,

save your connection profile to Wireless Network Management, (for further

information, please refer to your PC manufacturer).

30

2. Security

Using security. When disabled, Wi-Fi network becomes unsecure. If enabled, must use a

password.

You can use WEP (64- or 128-bit), WPA-PSK, or WPA2-PSK security.

How to configure Security

1. Select a security protocol from the Security Mode list.

(The Encryption box displays the corresponding encryption level.)

2. Enter a new network key in the Network Key box. (Depending on security protocol,

there will be limitation of string size in Network key.)

3. Click Apply button

.

Tip

Some WiFi clients get confused if user changed the security but not the network

name. If you changed security settings and do not get asked for a new network

key when you try to reconnect, then delete the existing “old” network name from

your “Preferred Networks” list. Try to reconnect again.

3. WPS

User can setup security easily by choosing PIN or PBC method in Wi-Fi Protected Setup.

The WPS feature allows to connect Wi-Fi and to setup security with a single button. If

there is a same SSID nearby the AP, it changes SSID and assigns a random password

using alphabet and numerical combination.

Firewall

Firewall settings are needed to protect Network intrusion from outside. It will protect

from outside by using MAC, IP, Port, URL, and Contents Filtering. Also it can block ping

from outside or remote access.

1. MAC/IP/Port Filtering

User may setup firewall rules to protect your network from virus, worm and malicious

activity on the Internet. User can set to refuse or to accept designated IP, MAC or Port.

31

How to Configure

1) MAC/IP/Port Filtering: Filtering enabled. (or disabled)

2) Default Policy : The packet that doesn’t match with any rules will be dropped.

3) MAC address: Put MAC Address that user wants to refuse or to accept.

4) Comment: Description (ex: aaa site Drop, yy_computer Drop, etc)

5) Dest IP address, Dest Port Range : Put destination IP Address & Port that wants to

refuse or to accept

6) Source IP address, Source Port Range : Put source IP Address & Port that wants to

refuse or to accept.

7) Protocol: Choose a protocol, TCP or UDP or ICMP.

8) Action: Choose actual matching conditions. (Drop or Accept)

2. System Security

You may configure the system firewall to protect AP/Router itself from getting attacked.

Remote management : Setting remote access. If enabled, it is possible to access

remotely but it may get intrusion from outside.

Ping from WAN Filter : It can block PING from outside or unblock it.

Stateful Packet Inspection : Stateful Firewall enable. A stateful firewall (any firewall that

performs stateful packet inspection (SPI) or stateful inspection) is a firewall that keeps

track of the state of network connections (such as TCP streams, UDP communication)

travelling across it. The firewall is programmed to distinguish legitimate packets for

different types of connections. Only packets matching to a known connection state will

be allowed by the firewall; others will be rejected.

32

3. Contents Filtering

You can setup Content Filter to restrict the improper content access.

Webs Content Filter : User can set filtering of contents that uses Proxy, Java, ActiveX.

Check and Click “Apply”.

URL Filter : User can set filtering of specific URL that might have viruses. Filtering URL

list can be added/deleted.

Traffic Control

1. Port Forwarding

Port forwarding allows remote computers, for example, computers on the Internet, to

connect to a specific computer or service within a private local area network (LAN) with

mapping of IP address and port number.

How to set Port Forwarding

1) In the menu, Advanced Settings > Traffic Control > Port Forwarding, do as follows.
A. Comment : Assign a name for Port Forward rules.
B. Protocol : Set Port Forward protocol. TCP or UDP
C. IP address : Set IP address for packets received from external source.
D. External Port : Set Port number for use of external application.
E. Internal Port : Set Port number for packets received from external source.

2) Click “Apply”.

3) For deleting, check the left box then Click “Delete”.

33

2. DMZ

DMZ host setting feature is to forward designate IP address to all ports that have not

been assigned from internal application, internal server, and port forward. In case user

cannot share the Internet because of unknown application service port number, DMZ

makes it possible.

If assigned as above settings, all ports from AP will be set as designated IP

(192.168.0.123) to send packets.

3. QoS

It is possible to control the speed of the Client’s connection to the Internet based on

bandwidth of connected AP.

For proper operations, it is important to know the basic values of internet speed of

connected AP and set accordingly.

Example)

CDMA EVDO rev.A : Down-3.1Mbps, Up-1.8Mbps

CDMA EVDO rev.0 : Down-2.4Mbps, Up-153kbps

34

Utility

1. VPN Pass-through

It is a VPN pass-through feature that sets VPN Server, VPN Client within the internal

network.

VPN pass-through is required if user is going to connect to a VPN (such as a corporate

system).

It is possible to set separate VPN protocols. By enabling protocols that used by VPN

server and client, user can connect to VPN through AP.

Supported VPN Protocol

 L2TP
 IPSec
 PPTP

2. DDNS

In AP network that uses PPP or DHCP with dynamic IP for FTP or Web server, the

external IP address may get altered. User needs to check each time and must make

changes accordingly. By using DDNS service, it provides a residential user's Internet

gateway that has a variable, often changing, IP address with a well known hostname

resolvable through standard DNS queries easily.

In order to use DDNS service, user needs to register user ID and domain to dyndns.org

(http://www.dyndns.org

, etc) or similar service sites. After registering, user must set as

below.

User can check the registered service.

35

How to setup.

1) Register the use of DDNS service to DDNS service site.

2) Choose DDNS Provider.

3) Setting User ID and password : Use ID/PW which registered in the service site.

4) Setting registered Host Name : Use host name which registered in the service site.

5) Click “Apply”.

3. Advanced Routing

Advanced Routing allows setting of routing table directly.

Setting up

1) Destination : Set Target IP

2) Range : Choose Host or Network

3) Gateway : Set Gateway address that transmits with Target.

4) Interface : Choose Interface. (LAN or WAN or custom)

5) Comment

36

Administration

1. Management

Administrator Settings : Set ID/PW for connecting Web UI.

Tip

Remember or write down your ID & PW.

In case of misplacing ID & PW, use reset button to set as a factory default.

Default values : ID: admin, PW: admin

NTP Settings : Setting time synchronization. It connects to NTP server automatically at

designated time and executes time synchronization function.

2. Firmware Upgrade

When AP is connected to the Internet, it is possible to upgrade the firmware through the

menu.

 Update Firmware
 Update Bootloader

3. Settings Management

User can save system settings for review, load or reset to factory default.

Export Settings : Save current status of AP to a PC. Before the firmware upgrade, Export

function saves configurations to a file.

Import Settings : Restore saved configuration file to AP. After the firmware upgrade,

Import function restores previous settings.

Load Factory Defaults : Restores back to the factory default values.

37

Status

Shows all status of AP.

1. DHCP Clients

The DHCP Clients section shows clients that are currently connected to the device. This is

another way you can find the MAC address for a particular device.

2. AP Status

It shows AP’s System Information, connection status of the Internet, and Network

Information.

3. Modem Status

Indicates status of the Modem.

Modem State : Connection status, Network service status, Received Signal Strength

information, and Battery level.

System Information : Roaming indicator, IP address, Subnet mask, and Connection time.

RUIM : RUIM Lock status, PIN/PUK Count.

EVDO : Indicates EVDO Network Status.

Channel, PN offset, State, Session, RSSI, Ec/Io, Tx Adjust, Tx Power, DRC

1x : Indicates 1x Network Status.

Channel, PN offset, SID, NID, state, RSSI, Ec/Io, Tx Adjust, Tx Power, FER

38

4. System Log

Records Wi-Fi activities.

User can check the AP’s activities through System Log.

It is possible to review AP’s acting status, IP distribution status, PPP connection status

and others.

5. Information

It displays Manufacturer Information, Firmware Version and Contact.

39

7 USB Modem Mode Connection for the First Time

NetKit Installation and Uninstall (Windows® XP)

1. NetKit Installation (Automatic)

1. Connect the device to USB port in personal computer with USB data cable. (The

device will power on automatically.) If USB DRIVER is not present, Modem package

Installer will run automatically.

Note

If Modem package Installer doesn’t work automatically, Execute RunPack.exe

manually.

2. Select the desire language as shown below.

3. Press button to proceed. By pressing button, the

installation of NetKit program will be aborted.

4. Welcoming message for using NetKit Program window appears.

40

5. Press Button. The program starts automatically.

41

6. Press button once it is done with program installation.

7. It will now start to install the driver. Please check whether the driver has been installed

properly by checking <Device Manager>.

[Start ▶ Control Panel ▶ System ▶ Hardware Tab ▶ Device Manager]

If Device Manager for Modems and Ports indicate as <WeTelecom Mobile USB

Modem> and<WeTelecom Mobile Serial Port 1/2>, then the driver has been

successfully installed.

42

Note : If installing driver manually, find the driver from Driver directory.

Run Setup.exe to install NetKit manually.

2. USB Driver Uninstall

1. Disconnect the modem from USB port before uninstalling the driver.

2. By clicking Uninstall in the [Start ▶ All program ▶ wetelecom], it will start

uninstalling as shown below.

43

NetKit Installation and Uninstall (Windows® Vista (or 7))

1. NetKit Installation (Automatic)

1. Connect the modem to USB port. If USB DRIVER is not present, Modem package

Installer will run automatically.

Note

If Modem package Installer doesn’t work automatically, Execute RunPack.exe

manually.

2. Select the desire language as shown below.

3. Press button to proceed. By pressing button, the

installation of NetKit program will be aborted.

4. Welcoming message for using NetKit Program window appears.

44

5. Press Button. The program starts automatically.

45

6. Press button once it is done with program installation.

7. It will now start to install the driver. Please check whether the driver has been installed

properly by checking <Device Manager>.

[Start ▶ Control Panel ▶ System ▶ Hardware Tab ▶ Device Manager]

If Device Manager for Modems and Ports indicate as <WeTelecom Mobile USB

Modem> and<WeTelecom Mobile Serial Port 1/2>, then the driver has been

successfully installed.

46

Note

If installing driver manually, find the driver from Driver directory.

Execute Setup.exe to install NetKit manually.

2. USB Driver Uninstall

1. Disconnect the modem from USB port before uninstalling the driver.

2. By clicking Uninstall in the [Start ▶ All program ▶ wetelecom], it will start

uninstalling as shown below.

47

8 Descriptions of the NetKit GUI in USB Modem Mode

Launch the NetKit

To launch the NetKit, double-click the shortcut icon of the NetKit on the desktop.

Note

If you are required to enter the Personal Identification Number (PIN) code, enter

the correct one and click OK. If you fail to enter the correct PIN or PIN

Unblocking Key (PUK) code, the network-related functions are unavailable.

Interface overview

1. Shortcut Icons

Internet Connection

Voice Call interface

Phonebook Interface

SMS Interface

Setting Interface

2. Status Information

Network signal Indicates the signal strength of the network:

Network information Display the profile of the current network : / /

SMS information

Display SMS message Notification

1. Text SMS : 2. Voice Mail :

Modem USB

connection

information

Display USB connection Status

1. Connected :

2. Disconnected :

Internet connection

information

Display Internet Connection Status

1. Internet Connected :

2. Internet Disconnected :

48

9 Internet Services in USB Modem Mode

Accessing the Internet

After setting the network and proper connection, you can access the network through

the NetKit.

Proceed as follows to connect to the internet.

1. Click to display the Connection interface.

2. Select Connect tab.

3. Enter proper UserName, Password, ServiceNum, and Click .

4. Open web browser on the PC to access the internet.

Note

You can disconnect the internet any time by pressing button.

History Information

History Information indicates connected time and Packet amount.

1. Click to display the Connection interface.

2. Select History Tab.

:

Search History by Date.

:

Delete the selected History.

:

Delete the All History.

49

10 SMS Service in USB Modem Mode

Creating and sending a Message

1. Click to display the SMS interface and Send tab will appear on the screen by

default.

2. Edit message on message box.

3. Edit number on Forward Number line. (Available 5 numbers, concurrently)

4. Click to search phone number, and Double-click searched number if you

want to send.

5. Click to send message.

Note

If you don’t want to save sent message, you can select ‘Not Save’ when SMS

window appears. Otherwise, the sent message will save in RUIM.

Inbox

Inbox stores the received messages.

1. Click to display the SMS interface.

2. Select Inbox Tab.

3. It displays received message, phone number, timestamp, and content. You can see

all messages by clicking the message.

50

:

Delete the selected message.

:

Delete all messages.

:

Reply to the selected message.

:

Forward the selected message.

Outbox

Outbox stores the transmitted message.

1. Click to display the SMS interface.

2. Select Outbox Tab.

3. It displays received message, phone number, timestamp, and content. You can see

all messages by clicking the message.

:

Delete the selected message.

:

Delete All messages.

:

Reply to the selected message.

:

Forward the selected message.

51

11 PhoneBook in USB Modem Mode

You can manage contacts in the phonebook of NetKit.

1. Click to display the PhoneBook interface.

2. You can check phone numbers in RUIM.

Creating a Contact

1. Click , then new window will popup.

2. Enter Index, Name and Phone number, and click

.

If you don’t want to save, click Exit button.

Editing a Contact

1. Click , after selecting a contact, it will popup phonebook edit window.

2. Click to edit the contact.

Deleting a Contact

1. Select the contact and Click .

Searching a Contact

1. Select the category for searching.

2. Click , you can see searched result in list box.

52

Sending a message

1. Select contact, and then Click .

2. Click to send the message.

53

12 Settings and Information in USB Modem Mode

Version Information

1. Click to display the Setting interface.

2. Select About Tab.

3. Shows Version Information.

Unlocking the PIN

1. When the RUIM card is locked, the Unlock PIN dialog box is displayed after you

start the NetKit.

2. Enter the correct PUK code.

3. Enter the new PIN code.

4. Click OK to complete the modification.

Selecting a PPP mode

1. Click to display the Setting interface.

2. Select User Tab.

3. Choose from the list in , and Click .

54

Enable / Disable PIN

1. Click to display the Setting interface.

2. Select RUIM Card Tab.

3. Select Enable or Disable in PIN Mode.

4. Enter PIN Code, and Click .

Change PIN Code

1. Click to display the Setting interface.

2. Select RUIM Card Tab.

3. Select Change in PIN Mode.

4. Enter pin code for Old PIN Code, New PIN Code and Verify New PIN Code, and

then Click .

Note

Entering the wrong PIN codes for 3 times, the RUIM card will be locked and

cannot use it until you have entered the correct PUK code. The NetKit prompts

you each remaining number of attempts for entering the PIN code or the PUK

code.

Selecting Always On Top mode

1. Click to display the Setting interface.

2. Select User Tab.

3. Select ON or OFF in Always On Top, and then Click .

55

Selecting a Pref Mode

1. Click to display the Setting interface.

2. Select User Tab.

3. Select Evdo+1x or Evdo only or 1x only in Pref Mode, and then Click .

Selecting a language

1. Click to display the Setting interface.

2. Select User Tab.

3. Select your language in Language list, and then Click .

56

13 How to Mac OS in USB Modem Mode

Version Information

Supported MAC OS 10.4 or higher

Drivers install

1. Plug the Skylink BEETLE modem in USB port MAC PC. Open SkyLink CD, start

mintechUSBCDC and install MAC Drivers.

2. Restart MAC PC.

3. Execute any connection manager for Skylink BEETLE Mobile Products.

4. Enter the User ID, Password and Number in Network Preference, and connect

Internet.

57

14 Trouble Shooting

This chapter will help you to solve common problems encountered while using the

Skylink BEETLE Mini Hotspot. Check following before continuing.

- Make sure that the wireless network covers your current location.

- Check antenna signal strength bar if you’re in weak area or no service area.

- Check if the driver has been installed properly.

- Make sure that system resources needed by Skylink BEETLE Mini Hotspot are not used

by other devices.

Issue Cause

Solution

Powered off without pressing the

power button

-Pressing the Factory Reset button

-Restarting the device

-Restoring the configuration settings

-Battery depleted

-Press the power button to turn it on.

-Remove Battery, AC Travel Adaptor and

USB Cable. Reinsert battery and press the

power button again.

If battery is depleted, charge it fully.

No connection or No Service

-No Service area

-RUIM card damaged

-RUIM Card not inserted

-Factory Reset

-Check antenna signal strength

-Insert RUIM Card again

-Check Wi-Fi settings

-Check battery level status

Powered off when connected to

computer with USB cable

- Incorrect USB Cable

- No battery

-Press the power button to turn the

device on.

-Make sure battery is inserted.

Reset and Factory Reset

1. How to reset in case of system lockdown or no connection which caused by

malfunction of the modem:

- Use Power button to power off. At this point, CDMA Modem and Wi-Fi

Router both get reset.

58

- In case it does not reset by Power Button, detach battery, unplug AC

Travel Adaptor, and USB Data cable. Then reinsert the battery and press

the Power button to try again.

2. Wi-Fi Router Factory Reset
A. From Skylink BEETLE

- Open the battery compartment.

- Press RST button located in lower left corner with sharp ended pen or

similar for 5 seconds. By pressing it, the device will reboot and all the

Wi-Fi settings will be initialized to factory settings.

B. From homepage, http://192.168.0.254

- Open the Web browser and enter ID and Password.

- Open “ Administration” and “Setting Management”

- Click “ Load Factory Defaults”.

59

15 Product Specification

Technical Specification

Table 1 : General Specifications

Model Name Skylink BEETLE

Type Mini Hotspot

Weight 83g

Dimensions 60.5mm X 100.5mm X 14.5mm

Wireless Network CDMA 1X/EV-DO

Wi-Fi Network 802.11 b/g/n 2.4GHz

Default SSID WMR-100AP_XXXXXX (6 decimals)

Battery

-Full Charging Time by AC T/A

-Full Charging Time by USB port of PC

1510mAh

3 Hours (when not in use)

4-5 Hours (when not in use)

Power Consumption 850mA,max

Chipset

QUALCOMM MSM6800A

RALINK RT3050

Interface Type

MicroUSB port for the device

Type A USB Port for computer

Table 2 : CDMA Technology

Technology CDMA 1x EVDO Rev. A/0, 1xRTT

Band Designation 450MHz

Transmit Frequency 452.5~457.475MHz (A Block)

Receive Frequency 462.5~467.475MHz (A Block)

Nominal Output Power 0.25 W (+24dBm)

Receiver Sensitivity Level Below -104dBm

60

Table 3 : Wi-Fi Technology

Technology 802.11 b/g/n

Operating Frequency in Europe 2.4–2.4835 GHz

Nominal Output Power

802.11 b

802.11 g/n

+17dBm

+14dBm

Minimum Receiver Sensitivity Level

802.11 b @ 11Mbps

802.11 g @ 54Mbps

802.11 n @ 135Mbps

Below -76dBm

Below -65dBm

Below -61dBm

Table 4 : Environmental Specifications

Operating Temperature -10°C ~+50°C

Storage Temperature -20°C ~+65°C