Page 1
Skylink® Wireless
Keyless Entry for Garage Doors
Model 318KR
1. INTRODUCTION
In this package, you will find a keyless entry transmitter with 3V lithium
batteries, a garage door receiver, a red / black wire and a clip.
Clip
Garage Door
Red/Black Wire
Receiver
Keyless Entry Transmitter
(Batteries inside)
2. INSTALLATION
The following instructions will show you how to install the rece iver. After
installing, the keyless entry transmitter (already programmed to the
receiver) can be used to operate your garage door opener.
You need to locate 2 things inside your garage to install the receiver:
1) the wall-mounted door control;
2) an electrical outlet, select an electrical outlet different from the one
already connected to the power cord of the garage door opener to
reduce the chance of interference. The further distance between
the receiver and the garage door opener, the less interference
between 2 devices.
Note: The length of the red/black wire is 20ft, so the receiver must be
plugged into an electrical outlet that is within 20ft of the wall mounted
door control. If there is no electrical outlet within 20ft of the wall
mounted door control, an extension cord can be used for temporary
installation.
Wall Mounted
Door Control
Remove power cord of garage
door opener before installation.
2. INSTALLATION (CONT)
Plug in the connector end of the Red/Black wire to the 318R
2
receiver. Note the orientation of the male & female connector.
Plug the receiver into an electrical outlet inside the garage.
3
The red light on the receiver should be on after being plugged into an
electrical outlet.
RECEIVER
RED/BLACK WIRE
Existing wires connected
to garage door opener.
(Do not remove)
Note: Alternative wiring options are available, the receiver can be
connected directly to the opener’s motor. Please contact customer
service for further information regarding alternative wiring options.
Re-connect the power cord of the Garage Door Opener.
4
Remove the battery isolator on the transmitter and enter the factory
5
default PIN [0,0,0,0], [#], you will hear 3 beeps indicating you have entered
the correct PIN. The door will now open.
Electrical
Outlet
Unplug the power cord of your garage door opener
WARNING
Remove the wall-mounted door control from the wall by removing
1
the screws. Connect the stripped ends of the Red/Black wire to the
before installation to ensure power is not connected.
2 terminals (2 screws) on the back of the wall mounted door
control. (Polarity does not matter.)
Existing
wires
Note: There should be another
pair of wires connected to the 2
terminals already. Do not remove/
Red /
Black wire
disconnect these existing wires.
Note: If you see no screws mounting the wall mounted door control,
the screws are probably under-neath the front cover. Remove the
front cover by pressing onto the tabs on top of the cover.
3. TROUBLE SHOOTING
Q: Door opener does not react after pressing the button on the transmitter.
A:- Ensure you hear 3 beeps from the keypad transmitter after entering
the default PIN and [#]. If you do not hear 3 beeps, that means the PIN
you entered is incorrect. Re-enter the correct PIN.
- If the red light on the receiver flashes after entering the PIN on the
transmitter, but the door opener does not respond, please ensure the
red/black wire is successfully connected from the receiver to the
wall mounted door control.
- Ensure the wires that are previously connected to the wall mounted
door control are not loose.
- Ensure the code setting on the keypad transmitter is the same as the
receiver. Refer to section 4 to check the code setting.
4. CHANGE THE OPERATION CODE FOR
BOTH TRANSMITTER AND RECEIVER
It is recommended to randomly set the operation code for your keypad
transmitter and receiver to avoid interference from other devices. Follow
the instructions below to change the operation code.
Pry off the cover on the back of the transmitter.
1
You will see 10 connectors labeled from
“1” to “10”, as shown. (the connectors
setting may not be the same as shown)
Remove front
cover first
Different wall-mounted door controls
Page 2
4. CHANGE THE OPERATION CODE FOR
BOTH TRANSMITTER AND RECEIVER (BOTH)
You can randomly remove some
2
connectors, leaving some in place.
A connector can be removed with
the clip, as shown.
6. CHANGE PIN
Follow the instructions below to change the PIN.
To change your PIN:
1. Enter the current PIN, (factory default PIN 0 0 0 0), press ,
2. Enter new 4 digit PIN, press ,
3. Enter new PIN again, press .
*
*
*
For example, if you are changing the PIN number from 0000 to
1234, enter the following sequence, 0000, ,1234, ,1234, .
**
*
If confirmed, the backlit LED flashes and the unit emits a long beep.
If the connector is placed on the top and middle posts, that column is
3
set on “ + ” . If the connector is placed on the middle and bottom posts,
that column is set on “ - ”. If the connector is removed completely,
(not placed on any posts), it is set to
“ 0 ”. (see diagram for examples of
how to set a column to the three
‘0’
different positions). When removing
a connector to set a column to “ 0 ”,
‘+’
save the connector in case you
change the code at a later date.
After setting up the code connectors on the keypad transmitter,
4
you are ready to set the same code on the receiver.
Remove the receiver from the electrical outlet before
WARNING
Remove the screw that holds
5
changing the code.
the connector cover, and remove
the cover.
You will see 10 connectors. The settings must match with those of
6
the transmitter.
Connectors
1 to 10 are
the same.
7 Put the cover and screw back onto the receiver. Plug the receiver
into an electrical outlet.
Enter [0,0,0,0] [#] will open the garage door.8
You can now mount the transmitter on a
9
desired location.
Lift up the cover and insert screw
above the keypad in the slot provided (a).
Remove the battery cover and insert
the second screw in the lower slot (b).
Tighten all screws. Replace the battery
cover, insert and tighten screw (c).
(c)
If you do not hear 3 beeps after the 4-digit PIN and [#] is entered,
that means you have entered an incorrect PIN, and the keypad transmitter
will not operate your garage door.
7. BATTERY
Two 3 volt Lithium type (CR2032) batteries (included).
‘-’
-
It is time to change
the batteries when
the backlight no
+
Battery Compartment
longer appears.
8. ADDITIONAL TRANSMITTER
You can add as many additional transmitters as you
want to control the same receiver. Simply set the
same operation code on all transmitters with the same
code setting on the receiver. Skylink® offers Keychain
Transmitter Model 318TN and Keyless Entry
Transmitter Model 318K to work with your receiver.
For more information, please visit our website at
www.skylinkhome.com or contact us.
9. CAUTION
RISK OF ELECTRICAL SHOCK. FOR INDOOR USE ONLY.
CAUTION : DISCONNECT POWER BEFORE CODE CHANGING.
REPLACE COVER AFTER CODE CHANGING.
Maximum Rating:
Input : 120VAC 60Hz 2W
10. FCC
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) This device must accept any interference
received, including interference that may cause undesired operation.
WARNING:
Changes or modifications to this unit not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
(a)
- Consult the dealer or an experienced radio/TV technician for help.
11. WARRANTY
If, within one year from date of purchase, this product should become defective
(except battery), due to faulty workmanship or materials, it will be repaired or
(b)
replaced, without charge. Proof of purchase and a Return Authorization are required.
5. KEYPAD OPERATION
NOTE:
The backlight comes on and a beep is emitted when any key is pressed.
The backlight of the keypad may not be visible when it is too bright
outside. When any key is pressed, the next key must be pressed w ithin 5
seconds or the backlight turns off and the sequence is cancelled. You
must begin again.
If the keypad does not emit a beep when pressed, wait a few seconds
and press the key again.
12. CUSTOMER SERVICE
If you would like to order Skylink’s products or have difficulty getting them to work,
please :
1. visit our FAQ web site at www.skylinkhome.com, or
2. email us at support@skylinkhome.com , or
3. call our toll free at 1-800-304-1187 from Monday to Friday, 9 am to 5 pm EST.
Fax +800 286-1320
CUSTOMER SERVICE
17 Sheard Avenue, Brampton, Ontario, Canada L6Y 1J3
Email:support@skylinkhome.com
http://www.skylinkhome.com
P/N. 101A207-004 Rev.4
©2005 SKYLINK GROUP
Loading...