"Telecommunication Products to solve
Telecommunication Problems"
CK-1P6
Promotion-On-Hold
Module
(For Panasonic KX-TG9391T, KX-
TG9392T, KX-TG9381, KX-TG9382)
3/14/13
Introduction
Thank you for purchasing the Skutch CK1P6 Promotion-On-Hold Module. The
CK-1P6 is a true plug and play device. The
unit does not require any "Learning" to
operate. When a call is placed ON HOLD
from the Corded Base set, or any one of the
cordless phones, the caller will hear the
Promotion-On-Hold audio. When the line is
re-answered, the audio automatically stops.
It's that simple!
CK-1P6 Installed on
KX-TG9391 Phone
Power Cube
1/8” Audio Adapter
CK-1P6
Box
Flat Cable
Audio Cable (RCA)
Installation
1- Position the CK-1P6 box under the base
telephone with the jacks facing towards the back of the phone. (See Fig. 1).
2- Connect the short modular cord [1&2 Phone on CK-1] to [LINE 1/2 on Phone].
3- Connect the audio cord from the AUDIO IN jack on the back of the CK-1 box, to your
audio player. If your audio player has a 1/8” phone jack, use the audio adapter on the end
of the cable.
4- Connect a MOD cord from Telephone Wall Jack 1&2 to [1&2 Line on CK-1].
Page 1 of 4
Sensor Board
Fig #1
LINE 2
Connect to Wall Jack
LINE 1/2
RCA
Connect to AudioPlayer
5- Make sure that the surface area of the base phone, where the sensor board is to be
mounted, is clean and free of all dust and oil film. Peel off the paper protectors from the
bottom of the sensor board, and place it OVER the LINE 1 and LINE 2 buttons on the
Base phone as shown in Fig. 2. The Sensor fits the contour of the phone, and will almost
“click” into place. No
alignment should be needed.
The Sensor board MUST
completely cover the LINE
buttons on the phone.
6- Connect the POWER CUBE
from the CK-1 Black Box to
115VAC power. That's it!
Center white
lines with
blue Label
Fig #2
Page 2 of 4
Testing the System:
1- Pickup line 1 on your telephone. The No."1" Green LED on the CK-1P6 Sensor Board
should light up.
2- Repeat this test for line 2. If both lines light up when picked up, the CK-1 Sensor
Board is mounted correctly. If either light does not light up, then
a) Make sure that the CK-1P6 and Phone is connected to power.
b) Make sure that the SENSOR BOARD firmly attached and is flat against the surface
of the phone.
Lights on CK-1 Box.
When you place a line on HOLD, the corresponding LED on the rear of the CK-1P6 box
lights up to confirm the Promotion-On-Hold condition.
Using Other models of telephones
The CK-1P6 will ONLY provide Promotion-On-Hold audio when a call is placed ON
HOLD from the KX-TG9391T Corded Phone/Base or any of it's cordless telephones.
Only ONE Base Phone unit can be used. A maximum of 6 cordless phones can be used
with one Base phone. Other models of telephones can be used with the Base, but the
Promotion On Hold audio will not be played to calls placed ON HOLD from these
telephones.
Tech Support - 916-786-6186
If you have any problems getting the unit to work properly feel free to give us a call.
Technical Support is available between the hours of 7:30 AM and 4:30 PM Pacific Time,
Monday through Friday.
• ONE YEAR LIMITED WARRANTY
This SKUTCH PRODUCT is warranted against defects for a period of one (1) year from the date of the
original invoice. Within this period, we will repair it without charge for parts and labor. To obtain
warranty service the product must be returned, at the customer's expense, to SKUTCH Electronics along
with a copy of the original invoice. After the unit has been repaired, SKUTCH will ship the PRODUCT
back via UPS GROUND service at our expense. If any other form of return shipment is requested, the
customer will pay for 100% of the shipping cost.
This Warranty does not apply if in the sole opinion of SKUTCH Electronics, the PRODUCT has been
damaged by lightning or any other Acts of God, or by accident, misuse, neglect, or improper packing,
shipping, modification or servicing by other than an authorized SKUTCH Service Center.
EXCEPT AS SPECIFICALLY PROVIDED IN THIS AGREEMENT, THERE ARE NO OTHER
WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED
WARRANTIES OR MERCHANTABILITIES OR FITNESS FOR A PARTICULAR PURPOSE AND IN
NO EVENT SHALL SKUTCH ELECTRONICS BE LIABLE FOR LOSS OF PROFITS OR BENEFITS,
INDIRECT, SPECIAL, CONSEQUENTIAL OR OTHER SIMILAR DAMAGES ARISING OUT OF
ANY BREACH OF THIS WARRANTY OR OTHERWISE.
Page 3 of 4
ACTA Statement
This equipment complies with Part 68 of FCC rules and the requirements
adopted by ACTA. On the bottom side of this equipment is a label that contains, among
other information, a product identifier in the format US: AAAEQ##TXXXX. If requested,
this number must be provided to the telephone company.
A plug and jack used to connect this equipment to the premises wiring and
telephone network must comply with the applicable FCC Part 68 rules and requirements
adopted by the ACTA. A compliant telephone cord and modular plug is provided with
this product. It is designed to be connected to a compatible modular jack that is also
compliant. See installation instructions for details.
The REN is used to determine the number of devices that may be connected to a
telephone line. Excessive RENs on a telephone line may result in the devices not ringing
in response to an incoming call. In most but not all areas, the sum of RENs should not
exceed five (5.0). To be certain of the number of devices that may be connected to a
line, as determined by the total RENs, contact the local telephone company. For
products approved after July 23, 2001, the REN for this product is part of the product
identifier that has the format US:AAAEQ##TXXXX. The digits represented by ## are the
REN without a decimal point (e.g., 03 is a REN of 0.3). For earlier products, the REN is
separately shown on the label.
If this equipment causes harm to the telephone network, the telephone company
will notify you in advance that temporary discontinuance of service may be required. But
if advance notice isn't practical, the telephone company will notify the customer as soon
as possible. Also, you will be advised of your right to file a complaint with the FCC if you
believe it is necessary.
The telephone company may make changes in its facilities, equipment,
operations or procedures that could affect the operation of the equipment. If this
happens the telephone company will provide advance notice in order for you to make
necessary modifications to maintain uninterrupted service.
If trouble is experienced with this equipment, for repair or warranty information,
please contact our company. If the equipment is causing harm to the telephone network,
the telephone company may request that you disconnect the equipment until the
problem is resolved.
Connection to party line service is subject to state tariffs. Contact the state public
utility commission, public service commission or corporation commission for information.
Page 4 of 4
Loading...