Skutch Electronics BA-1 User Manual
ONE YEAR LIMITED WARRANTY
This SKUTCH PRODUCT is warranted against defects for a period
of one (1) year from the date of original invoice. Within this period,
we will repair the PRODUCT without charge for parts and labor. To
obtain warranty service the product must be returned, at the customer’s
expense, to SKUTCH Electronics along with a copy of the original
invoice. After the unit has been repaired, SKUTCH will ship the
PRODUCT back via UPS GROUND service at our expense. If any
other form of return shipment is requested, the customer will pay for
100% of the shipping cost.
This Warranty does not apply if in the sole opinion of SKUTCH
Electronics, the product has been damaged by lightning or any other
Acts of God, or by accident, misuse, neglect, or improper packing,
shipping, modification or servicing by other than an authorized
SKUTCH Service Center.
EXCEPT AS SPECIFICALLY PROVIDED IN THIS AGREEMENT, THERE
ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING,
BUT NOT LIMITED TO, ANY IMPLIED WARRANTIES OR
MERCHANTABILITIES OR FITNESS FOR A PARTICULAR PURPOSE AND
IN NO EVENT SHALL SKUTCH ELECTRONICS BE LIABLE FOR LOSS OF
PROFITS OR BENEFITS, INDIRECT, SPECIAL, CONSEQUENTIAL OR
OTHER SIMILAR DAMAGES ARISING OUT OF ANY BREACH OF THIS
WARRANTY OR OTHERWISE.
“Telecommunication Products to solve Telecommunication Problems”
ELECTRONICS, INC.
209 Kenroy Lane #9
Roseville, California 95678
Voice (916) 786-6186 FAX (916) 783-1909
E-MAIL skutch@inreach.com http://www.skutchelectronics.com
BA-1
BA-1
BA-1BA-1
Hold Button Adapter for use with BA-704
Hold Button Adapter for use with BA-704
Hold Button Adapter for use with BA-704Hold Button Adapter for use with BA-704
series
series
seriesseries
SN A112001 and above
Introduction
Thank you for purchasing the Skutch BA-1 Hold Button Adapter for
use with the BA-704 series Promotion-On-Hold modules. The BA-1
mounts directly to your corded telephone and becomes an integral part
of the phone itself. It supplies a HOLD BUTTON and four "IN-USE"
lights that show the accurate status of each telephone line. The BA-1 is
perfect for heavy use phones where properly functioning "IN-USE"
lights and easy to use HOLD functions are mandatory. A separate
BA-1 should be installed on each high traffic corded telephone. Other
phones and all cordless phones can still use the STAR tone to activate
the Promotion-On-Hold system. The BA-1 requires that a Skutch BA704 Promotion-On-Hold module be used on one of the telephones.
Installation Diagram
Placing A Call ON HOLD
Press the hold button and hang up the telephone or select another line
within 6 seconds of pressing the button.
Taking a call off hold
Simply select the line and pick up the phone.
Status of "IN-USE" Lights
OFF
Steady RED
or line is not connected to BA-1.
Steady GREEN
: Indicates line is hung up and not in use.
: Another phone is currently using the line,
: Line is being used by this phone.
123
456
789
*0#
Te l ephone
Te l ephone J ack s
1& 2
BA-1
Line s
4
3
2
1
HOLD
3& 4
115V AC
Back View
3- 4
Phone
3-4
Line
1-2-3
Phone
1-2-3
Li ne
Flashing RED
Flashing GREEN
: Another phone has placed the call ON HOLD.
: This phone has placed the line ON HOLD.
Disabling a non used "IN-USE" light
If you have less than four lines then the unused "IN-USE" lights on
the BA-1 will stay lit RED. If you wish you may disable the unused
lights by pressing and holding down the BA-1 HOLD button until
only the desired lights are lit up YELLOW. At this point release the
HOLD button. The BA-1 will retain this information until the unit is
disconnected from power.
Power Up
On initial power up, the lights will alternately flash RED and GREEN for 2 seconds.
Tech Support - 916-786-6186
If you have any problems getting the BA-1 to work properly feel free to give us a
call. Technical Support is available between the hours of 7:30 AM and 4:30 PM
Pacific Time, Monday through Friday.
Loading...