• Installation
Follow the 6 steps below for connection to your AT&T 843, 853, 854,
874, 953 and 954 phones.
Make sure the audio cable has the right plug for the AS-703-A
!
(male phono or RCA).
Make sure you are NOT using a "Dubbing" audio cord.
!
Try repgrogramming the station ID's for each of the phones, start
!
with 22 and go down from there.
Phone
1. Connect cord from L1&L2
on phone, to 1,2&3 OUT
on AS703.
3. Connect cord
from 1,2&3 IN
on AS703 to
Phone Jack #1.
6. Connect
audio
cable
from
AS-703 to
Audio
Source.
Phone Jack #1
RJ-14
Lines 1 & 2
Head
Phones
LINES
3 & 4
IN
Phone Jack #2
RJ-14
Lines 3 & 4
4. Connect cord
from 3&4 IN
on AS703 to
Phone Jack#2.
Audio
Source
5. Plug
AS703
into
120VAC
wall
outlet.
• Operation
Once the AS-703-A is connected it will set itself up as you start to use
your phones. The unit will play music to all calls that are placed ON HOLD.
Make sure that you adjust the level of the music to the proper level on the
audio source.
• Troubleshooting Guide
No Audio But The Lights Turn On The AS-703-A
Make sure the Message Source is playing.
!
Make sure the Message Source volume is turned up.
!
Make sure that the audio cable is connected from the headphone
!
jack on the Message Source, to the AUDIO IN jack on the AS703-A.
Music does not always shut OFF or turn ON.
Re-program the STATION ID number in EACH telephone. This
!
can be done as follows:
1- The phone MUST be "ON HOOK" to program it.
2- Press the
3- Press *.
4- Press #.
5- Press xx. xx equals a two digit STATION ID code. Each phone
has to have a different code. Codes can range from 22 to 11. Always start
with 22 and work down.
6- Press the
If the phone accepts the STATION ID it will confirm by RINGING one
time. If it keeps ringing, this indicates that the ID is already being used by
another phone. In this case re-enter a new STATION ID code.
NOTE: If the phones loose power for 5 seconds or more, they will loose
their STATION ID numbers. You can put 4 AA batteries in the phones to
hold this information and protect it against power failures. Look on the
bottom of the phone for the battery compartment access.
[PROGRAM]
[INTERCOM]
button.
button.
• Tech Support - 916-786-6186
If you have any problems getting the unit to work properly feel free to
give us a call. Technical Support is available between the hours of 7:30 AM
and 4:30 PM Pacific Time, Monday through Friday.
• ONE YEAR LIMITED WARRANTY
This SKUTCH PRODUCT is warranted against defects for a period of
one (1) year from the date of the original invoice. Within this period, we will
repair it without charge for parts and labor. To obtain warranty service the
product must be returned, at the customer's expense, to SKUTCH Electronics
along with a copy of the original invoice. After the unit has been repaired,
SKUTCH will ship the PRODUCT back via UPS GROUND service at our
expense. If any other form of return shipment is requested, the customer will
pay for 100% of the shipping cost.
This Warranty does not apply if in the sole opinion of SKUTCH
Electronics, the PRODUCT has been damaged by lightning or any other Acts
of God, or by accident, misuse, neglect, or improper packing, shipping,
modification or servicing by other than an authorized SKUTCH Service
Center.
EXCEPT AS SPECIFICALLY PROVIDED IN THIS AGREEMENT,
THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED,
INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTIES
OR MERCHANTABILITIES OR FITNESS FOR A PARTICULAR
PURPOSE AND IN NO EVENT SHALL SKUTCH ELECTRONICS BE
LIABLE FOR LOSS OF PROFITS OR BENEFITS, INDIRECT, SPECIAL,
CONSEQUENTIAL OR OTHER SIMILAR DAMAGES ARISING OUT
OF ANY BREACH OF THIS WARRANTY OR OTHERWISE.
"Telecommunication Products to solve Telecommunication Problems"
LIN E S
3 & 4
IN
AS-703AM
Four Line Promotion-On-Hold Module
V1.00
For the AT&T 843, 853, 854, 874, 953, & 954
telephones
Loading...