AS-2500-3 Remote
Power Controller
Version 1.00
Table of Content
TABLE OF CONTENT .......................2
INTRODUCTION ................................3
CONTROL OUTPUTS ........................3
INSTALLATION..................................3
PROGRAM THE ACCESS CODE ....3
VERIFY THE ACCESS CODE ..........3
OPERATION ........................................4
CONTROL ACCESS ...........................4
VERIFY CHANNEL STATES ...........4
TIME-OUT............................................4
SHORT CUT INSTRUCTIONS .........4
Program the Access code....................... 4
•
Verify the Access code ...........................4
•
Normal operation................................... 4
•
TECH SUPPORT - 916-786-6186 .......4
WARRANTY ........................................4
Al Sandige Page 2 12/05/01
Introduction
The AS-2500-3 allows a method of remotely
controlling up to two different devices via the
telephone lines. Both channel 1 and 2 may be turned
"ON" or "OFF" as desired. The channel status is
stored in a State-Of-The-Art EEPROM which means
that the AS-2500-3 will retain the proper state of the
channels even after long power outages. The
EEPROM is capable of retaining information for up
to 100 years without power. The unit features a 4
digit security access code that prevents nonauthorized persons from controlling the unit. This
code can be changed or verified by the user.
Control outputs
Channel 1-an unfused, 110VAC, 3 prong
!
power outlet, rated at 10 amps. This
outlet can be used to directly control AC
powered devices, including computers.
Channel 2-an isolated (up to 1000VAC)
!
relay contact closure, can pass AC/DC
voltages (110VAC max.), 1/8" mini
phone jack output, rated at 2 amps. This
output is located on the back of the unit
and is labeled RESET SWITCH.
3) Connect the other end of the supplied modular
cable to any standard telephone company line
(RJ-11).
4) Connect the power cord to power.
Program the
Access code
The AS-2500-3 allows you to program your
own four digit access code; do the following:
1) Place the PROGRAM SWITCH, on the back of
the unit, to the PROGRAM position.
2) Call the telephone line, connected to the unit,
from any touch tone capable telephone.
3) When the unit answers, you will hear a
confirmation tone.
4) After the confirmation tone is finished, dial a
touch tone *; you will then hear a pulsating
acknowledgment tone.
5) Enter your new four digit access code (the * and
# cannot be used in your access code); you will
then hear a pulsating acknowledgment tone.
You can now verify your access code by going
to Step 4 of VERIFYING YOUR ACCESS CODE,
or you can hang up and place the PROGRAM
SWITCH, on the back of the unit, to the NORMAL
position.
Verify the access
Installation
1) Place the PROGRAM SWITCH, on the back of
ELECTRON ICS
RESET
MODEL:
S/N:
CODE :
SW ITCHED
1) The AS-2500-3 installs the same way as an
answering device.
2) Connect the supplied modular cable to the back
of the AS-2500-3 into the "LINE" jack. Note
that the "TAD" jack is NOT used on this unit.
Al Sandige Page 3 12/05/01
PROGRAM
SWITCH NORMAL
TAD LINE
Wal l
Phone
Jack
the unit, to the PROGRAM position.
2) Call the telephone line, connected to the unit,
from any touch tone capable telephone.
3) When the unit answers, you will hear a
confirmation tone.
4) After the confirmation tone is finished, dial a
touch tone #.
5) The unit will play the access code to you
through a series of BEEPS, i.e. the code 1 2 3 4
will give you: 1 BEEP, two second pause, 2
BEEPS, pause, 3 BEEPS, pause and 4 BEEPS
(NOTE: you will get 10 BEEPS for a 0).
You can now program a new access code by
going to Step 4 of ACCESS CODE
code
PROGRAMMING, or you can hang up and place
the PROGRAM SWITCH, on the back of the unit, to
the NORMAL position.
In ALL modes of operation, the AS-2500-3 will
hang up if no touch tone is detected within a 15
second period.
Operation
For normal operation, the PROGRAM
SWITCH, on the back of the unit, MUST be in the
NORMAL position.
Control access
1) To turn the control outputs on/off, do the
following:
2) Call the telephone line, connected to the unit,
from any touch tone capable telephone.
3) When the unit answers, you will hear a
confirmation tone.
4) After the confirmation tone, enter your four digit
access code; you will then hear a pulsating
acknowledgment tone.
5) * 1 --Turns Channel 1 ON.
6) # 1 --Turns Channel 1 OFF.
7) * 2 --Turns Channel 2 ON.
8) # 2 --Turns Channel 2 OFF.
9) * # --Verifies the current state of both channels.
Short cut
instructions
Program the Access code
•
1) PROGRAM SWITCH up, then call unit.
2) After the tone, enter *, then your new access
code (i.e. 1 2 3 4).
3) Hang up.
4) PROGRAM SWITCH down.
Verify the Access code
•
1) PROGRAM SWITCH up, then call unit.
2) After the tone, enter * #.
3) The unit will give the access code in BEEPS.
4) Hang up.
5) PROGRAM SWITCH down.
Normal operation
•
1) PROGRAM SWITCH down, then call unit.
2) Enter your four digit access code.
3) Hang up.
Verify channel
Tech Support -
states
916-786-6186
You can verify the state of each channel by
completing the steps in CONTROL ACCESS. When
you enter * #, the unit will give you: one LOW tone
(this indicates channel 1), either one short HIGH
tone (if channel 1 is off) or 10 short BEEPS (if
channel 1 is on), two LOW tones (this indicates
channel 2) and either one short HIGH tone (if
channel 2 is off) or 10 short BEEPS (if channel 2 is
on).
Time-out
Al Sandige Page 4 12/05/01
If you have any problems getting the unit to
work properly feel free to give us a call. Technical
Support is available between the hours of 7:30 AM
and 4:30 PM Pacific Time, Monday through Friday.
WARRANTY
This SKUTCH PRODUCT is warranted against
defects for a period of one (1) year from the date of
the original invoice. Within this period, we will
repair it without charge for parts and labor. To
obtain warranty service the product must be
returned, at the customer's expense, to SKUTCH
Electronics along with a copy of the original invoice.
After the unit has been repaired, SKUTCH will ship
the PRODUCT back via UPS GROUND service at
our expense. If any other form of return shipment is
requested, the customer will pay for 100% of the
shipping cost.
This Warranty does not apply if in the sole
opinion of SKUTCH Electronics, the PRODUCT
has been damaged by lightning or any other Acts of
God, or by accident, misuse, neglect, or improper
packing, shipping, modification or servicing by
other than an authorized SKUTCH Service Center.
EXCEPT AS SPECIFICALLY PROVIDED IN
THIS AGREEMENT, THERE ARE NO OTHER
WARRANTIES, EXPRESSED OR IMPLIED,
INCLUDING, BUT NOT LIMITED TO, ANY
IMPLIED WARRANTIES OR
MERCHANTABILITIES OR FITNESS FOR A
PARTICULAR PURPOSE AND IN NO EVENT
SHALL SKUTCH ELECTRONICS BE LIABLE
FOR LOSS OF PROFITS OR BENEFITS,
INDIRECT, SPECIAL, CONSEQUENTIAL OR
OTHER SIMILAR DAMAGES ARISING OUT OF
ANY BREACH OF THIS WARRANTY OR
OTHERWISE.
Al Sandige Page 5 12/05/01
Loading...