Skil 1450 Instruction Manual

Download

SPIRAL SAW 1450 (F0151450..)

ORIGINAL INSTRUCTIONS 8

NOTICE ORIGINALE 12

ORIGINALBETRIEBSANLEITUNG 16

ORIGINELE GEBRUIKSAANWIJZING 21

BRUKSANVISNING I ORIGINAL 25

ORIGINAL BRUGSANVISNING 29

ORIGINAL BRUKSANVISNING 33

FIN

ALKUPERÄISET OHJEET 37

MANUAL ORIGINAL 41

MANUAL ORIGINAL 46

ISTRUZIONI ORIGINALI 50

EREDETI HASZNÁLATI UTASÍTÁS 55

PŮVODNÍM NÁVODEM K POUŽÍVÁNÍ 59

ORİJİNAL İŞLETME TALİMATI 63

INSTRUKCJA ORYGINALNA 67

ПОДЛИННИК РУКОВОДСТВА ПО ЭКСПЛУАТАЦИИ

www.skilmasters.com

SKIL Europe BV - Konijnenberg 60 07/09 2610399939 4825 BD Breda - The Netherlands

ОРИГІНАЛЬНА ІНСТРУКЦІЯ

З ЕКСПЛУАТАЦІЇ

ΠΡΩΤΟΤΥΠΟ Ο∆ΗΓΙΩΝ ΧΡΗΣΗΣ 82

INSTRUCŢIUNI DE FOLOSIRE ORIGINALE

ОРИГИНАЛНО РЪКОВОДСТВО ЗА ЕКСПЛОАТАЦИЯ

PÔVODNÝ NÁVOD NA POUŽITIE 96

ORIGINALNE UPUTE ZA RAD 101

SRB

ORIGINALNO UPUTSTVO ZA RAD 105

SLO

IZVIRNA NAVODILA 109

EST

ALGUPÄRANE KASUTUSJUHEND 113

ORIĢINĀLĀ LIETOŠANAS PAMĀCĪBA 117

ORIGINALI INSTRUKCIJA 121

AR FA

133 130

ME77

1450

500

Watt

EPTA 01/2003

1,3 kg

R A

15000-30000

4 mm

RUBBER

5x1x

~3 mm

PLASTICS

MAX.

22 mm

2610950521 2610942614

5-6

3-6

2-3

1-2

2 mm

18 mm

5 mm

5-6

34-35 mm

Spiral saw 1450 INTRODUCTION

• This tool is intended for cutting gypsum, wood,

plexiglass, plastics and soft wall tiles

• Read and save this instruction manual 3

TECHNICAL SPECIFICATIONS 1 TOOL ELEMENTS 2

A Spindle-lock button B Collet nut C Wrench D Collet E On/off switch F Speed selection wheel G Locking lever H Depth adjustment accessory J Tool collar K Adjustment screw L Depth gauge M Dust suction accessory N Adjustment knobs P Extension for vacuum cleaner Q Multi-functional bit (5) R Ventilation slots S Tile bit T Circular guide

SAFETY

GENERAL SAFETY INSTRUCTIONS

WARNING! Read all safety warnings and all

instructions. Failure to follow the warnings and

instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. The term “power tool” in the warnings refers to your mains-operated (corded) power tool or batteryoperated (cordless) power tool.

1) WORK AREA SAFETY

a) Keep work area clean and well lit.

Cluttered or dark areas invite accidents.

b) Do not operate power tools in explosive

atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks

which may ignite the dust or fumes.

c) Keep children and bystanders away while operating

a power tool. Distractions can cause you to lose control.

2) ELECTRICAL SAFETY a) Power tool plugs must match the outlet.

Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools.

Unmodiﬁ ed plugs and matching outlets will reduce risk of electric shock.

b) Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric

shock if your body is earthed or grounded.

c) Do not expose power tools to rain or wet conditions.

Water entering a power tool will increase the risk of electric shock.

d) Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase

the risk of electric shock.

e) When operating a power tool outdoors,

use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.

f) If operating a power tool in a damp location is

unavoidable, use an earth leakage circuit breaker. Use of an earth leakage circuit breaker reduces the risk of electric shock.

3) PERSONAL SAFETY a) Stay alert, watch what you are doing and use

common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication.

A moment of inattention while operating power tools may result in serious personal injury.

b) Use personal protective equipment. Always wear

eye protection. Protective equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries.

c) Prevent unintentional starting. Ensure the switch is

in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your ﬁ nger on the

switch or energising power tools that have the switch on invites accidents.

d) Remove any adjusting key or wrench before turning

the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.

e) Do not overreach. Keep proper footing and balance

at all times. This enables better control of the power tool in unexpected situations.

f) Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewellery or long

hair can be caught in moving parts.

g) If devices are provided for the connection of dust

extraction and collection facilities, ensure these are connected and properly used. Use of dust collection

can reduce dust-related hazards.

4) POWER TOOL USE AND CARE a) Do not force the power tool. Use the correct power

tool for your application. The correct power tool will

do the job better and safer at the rate for which it was designed.

b) Do not use the power tool if the switch does not turn

it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.

c) Disconnect the plug from the power source and/or

the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. Such pr

the risk of starting the power tool accidentally.

d) Store idle power tools out of the reach of children

and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool.

Power tools are dangerous in the hands of untrained users.

e) Maintain power tools. Check for misalignment or

binding of moving parts, breakage of parts and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly

maintained power tools.

f) Keep cutting tools sharp and clean.

Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.

g) Use the power tool, accessories and tool bits etc.,

in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations

different from those intended could result in a hazardous situation.

5) SERVICE a) Have your power tool serviced by a qualified repair

person using only identical replacement parts.

This will ensure that the safety of the power tool is maintained.

SPECIFIC SAFETY INSTRUCTIONS FOR SPIRAL SAWS

A) The outside diameter and the thickness of your

accessory must be within the capacity rating of your power tool. Incorrectly sized accessories cannot be

adequately guarded or controlled.

B) Wear personal protective equipment 4. Depending

on application, use face shield, safety goggles or safety glasses. As appropriate, wear dust mask, hearing protectors, gloves and shop apron capable of stopping small abrasive or workpiece fragments.

The eye protection must be capable of stopping ﬂ ying debris generated by various operations. The dust mask or respirator must be capable of ﬁ ltrating particles generated by your operation. Prolonged exposure to high intensity noise may cause hearing loss.

C) Keep bystanders a safe distance away from work

area. Anyone entering the work area must wear personal protective equipment. Fragments of the

workpiece or of a broken accessory may ﬂ y away and cause injury beyond the immediate area of operation.

D) Hold the power tool only by the insulated gripping

surfaces when performing an operation where the cutting tool may contact hidden wiring or its own power cord. Contact with a “live” wire will also make

exposed metal parts of the power tool “live” and shock the operator.

E) Position the cord clear of the spinning accessory.

If you lose control, the cord may be cut or snagged and your hand or arm may be pulled into the spinning accessory.

eventive safety measur

es reduce

F) Never lay the power tool down until the accessory

has come to a complete stop. The spinning accessory may grab the surface and pull the power tool out of your control.

G) Do not run the power tool while carrying it at your

side. Accidental contact with the spinning accessory could snag your clothing, pulling the accessory into your body.

H) Regularly clean the power tool’s air vents.

The motor’s fan will draw the dust inside the housing and excessive accumulation of powdered metal may cause electrical hazards.

I) Do not operate the power tool near flammable

materials. Sparks could ignite these materials.

GENERAL

• This tool should not be used by people under the age of 16 years

• Only use this tool for applications without the use of water

• Always disconnect plug from power source before making any adjustment or changing any accessory

• Protect accessories from impact, shock and grease

ACCESSORIES

• Only use the original accessories supplied with the tool (2610950521 & 2610942614); damage due to the use of non-original accessories will be excluded from the warranty

• SKIL can assure ﬂ awless functioning of the tool only when the correct accessories are used which can be obtained from your SKIL dealer

• Use only accessories with an allowable speed matching at least the highest no-load speed of the tool

• Do not use damaged or deformed cutting bits

• Only use sharp cutting bits

• Cutting bits become hot during use; do not touch them until they have cooled down

• Handle the sharp cutting bits with caution

• Only use cutting bits of 4 mm (5/32”) Ø

OUTDOOR USE

• When used outdoors, connect the tool via a fault current (FI) circuit breaker with a triggering current of 30 mA maximum, and only use an extension cord which is intended for outdoor use and equipped with a splashproof coupling-socket

BEFORE USE

• Always check that the supply voltage is the same as the voltage indicated on the nameplate of the tool (tools with a rating of 230V or 240V can also be connected to a 220V supply) Do not work materials containing asbestos (asbestos

• is consider

• Secure the workpiece (a workpiece clamped with clamping devices or in a vice is held more securely than by hand)

• Use completely unrolled and safe extension cords with a capacity of 16 Amps (U.K. 13 Amps)

ed car

cinogenic)

• Dust from material such as paint containing lead, some wood species, minerals and metal may be harmful (contact with or inhalation of the dust may cause allergic reactions and/or respiratory diseases to the operator or bystanders); wear a dust mask 5 and

work with a dust extraction device when connectable

• Certain kinds of dust are classiﬁ ed as carcinogenic (such as oak and beech dust) especially in conjunction with additives for wood conditioning; wear a dust

mask 5 and work with a dust extraction device when connectable

• Follow the dust-related national requirements for the materials you want to work with

• Avoid damage that can be caused by screws, nails and other elements in your workpiece; remove them before you start working

• Use suitable detectors to find hidden utility lines or call the local utility company for assistance (contact with electric lines can lead to ﬁ re or electrical shock; damaging a gas line can result in an explosion; penetrating a water pipe will cause property damage or an electrical shock)

• Ensure that the collet size corresponds with the shaft size of the accessory

DURING USE

• If the cord is damaged or cut through while working, do not touch the cord, but immediately disconnect the plug

• Never use the tool when cord is damaged; have it replaced by a qualiﬁ ed person

• Keep hands away from rotating accessories

• Never use spindle lock while tool is running (damage due to improper handling will be excluded from the guarantee)

• In case of electrical or mechanical malfunction, immediately switch off the tool and disconnect the plug

AFTER USE

• After switching off the tool, never stop the rotation of the accessory by a force applied against it

• Store tool in locations where temperature will not exceed 50°C

WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):

• Do not connect the blue (= neutral) or brown (= live) wire in the cord of this tool to the earth terminal of the plug

• If for any reason the old plug is cut off the cord of this tool, it must be disposed of safely and not left unattended

USE

• Mounting of accessories 6

! switch off the tool and disconnect the plug ! ensure that collet size corresponds with shaft

size of accessory

- push spindle-lock button A and hold it while you turn

collet nut B by hand until the spindle lock prevents further rotation and loosen collet nut B with wrench C

! push spindle-lock button A only when tool is at a

standstill

- insert required accessory in collet D (leave

approximately 3 mm of the shaft exposed)

- push spindle-lock button A and hold it while you tighten collet nut B with wrench C

! avoid excessive tightening of collet nut B ! never tighten collet nut, if there is no accessory in

collet; collet may be damaged

• Before using the tool

- ensure that accessory is correctly mounted and ﬁ rmly tightened

- check if accessory runs freely by turning it by hand

- test-run tool for at least 30 seconds at highest noload speed in a safe position

- stop immediately in case of considerable vibration or other defects and check tool to determine the cause

• On/off

- switch on/off the tool by pushing switch E 2 in “I”/”O” position

! be aware of the sudden impact when the tool is

switched on

• Speed control 7 For optimal results on different materials

- select speed with wheel F (also while tool is running)

- use table 8 as reference for determining the right speed

- before starting a job, ﬁ nd the optimal speed by testing out on spare material

! after longer periods of working at low speed,

allow the tool to cool down by running it for approximately 3 minutes at high speed with no load

• Depth adjustment accessory 9 For guiding the tool along the workpiece at a pre-set

cutting depth

- release lever G before mounting/removing accessory H onto/from tool collar

! lock lever G after mounting accessory H

- loosen adjustment screw K counter-clockwise with wrench C as illustrated

- slide depth gauge L up or down to the desired cutting depth and tighten screw K clockwise

• Dust suction accessory 0 For combining tool guidance at a pre-set cutting depth

with dust suction

- release lever G before mounting/removing accessory M onto/from tool collar

! lock lever G after mounting accessory M

- loosen 2 adjustment knobs N counter-clockwise

- slide depth gauge L up or down to the desired cutting depth and tighten 2 adjustment knobs N clockwise

- connect vacuum cleaner to extension P

! never let the vacuum cleaner hose interfere with

the cutting operation

• Operating the tool !

- insert multi-functional bit Q

- mount depth adjustment accessory H or dust suction accessory M

- set wheel F 2 to desired speed

- place the bit onto the workpiece at a 45° angle

- switch on the tool

- slowly lower the bit into the workpiece at a 45° angle

- after reaching the desired cutting depth, move the tool to its normal working position again

- continue to cut along the cutting line in a clockwise direction with the accessory base resting ﬂ at on the workpiece

- cut slowly for optimal control (fast cutting will cause excessive heat and may shorten the service life of the bit)

- after completing the cut, switch off the tool and carefully remove it from the workpiece

! always test out first on a piece of scrap material

• Cutting soft wall tiles @

! insert tile bit S

- create a starting-point for plunge cutting by slowly making a groove on the tile’s surface at a 45° angle

- start rotating the tool at a 45° angle, while keeping the point of the cutting bit ﬁ rmly positioned within the groove

- continue rotating the tool until the cutting bit has completely plunged through the wall tile

- move the tool to a 90° angle and guide it up and down along the desired cutting line (the up and down movement prolongs the service life of the cutting bit)

• Holding and guiding the tool #

! while working, always hold the tool at the grey-

coloured grip area(s)

- hold tool ﬁ rmly with both hands, so you will have full control of the tool at all times

- keep ventilation slots R 2 uncovered

- do not apply too much presssure on the tool (excessive pressure will cause excessive heat and may shorten the service life of the accessory)

APPLICATION ADVICE

• For making circular cut-outs use circular guide T $

• When cutting a hole in a vertical surface, start and end your cut at the top, so that the scrap part will not drop onto the rotating bit

MAINTENANCE / SERVICE

• Always keep tool and cord clean (especially the ventilation slots R 2)

! do not attempt to clean ventilation slots by

inserting pointed objects through openings

! disconnect the plug before cleaning

• Always clean depth adjustment accessory H 2 and dust suction accessory M 2 after use

• If the tool should fail despite the care taken in manufacturing and testing procedures, repair should be carried out by an after-sales service centre for SKIL power tools

- send the tool undismantled together with proof of

purchase to your dealer or the nearest SKIL service station (addresses as well as the service diagram of the tool are listed on www.skilmasters.com)

- in observance of European Directive 2002/96/EC on waste of electric and electronic equipment and its implementation in accordance with national law, electric tools that have reached the end of their life must be collected separately and returned to an environmentally compatible recycling facility

- symbol % will remind you of this when the need for disposing occurs

CE DECLARATION OF CONFORMITY

• We declare under our sole responsibility that this product is in conformity with the following standards or standardized documents: EN 60 745, EN 55 014, in accordance with the provisions of the directives 2006/95/EC, 2004/108/EC, 98/37/EC (until Dec. 28,

2009), 2006/42/EC (from Dec. 29, 2009 on)

• Technical file at: SKIL Europe BV (PT-SEU/PJE), 4825 BD Breda, NL

09 SKIL Europe BV A. v.d. Kloot

NOISE/VIBRATION

• Measured in accordance with EN 60 745 the sound pressure level of this tool is 88 dB(A) and the sound power level 99 dB(A) (standard deviation: 3 dB), and the vibration 3.0 m/s² (hand-arm method; uncertainty K = 1.5 m/s²)

• The vibration emission level has been measured in accordance with a standardised test given in EN 60 745; it may be used to compare one tool with another and as a preliminary assessment of exposure to vibration when using the tool for the applications mentioned

- using the tool for different applications, or with

different or poorly maintainted accessories, may signiﬁ cantly increase the exposure level

- the times when the tool is switched off or when it is

running but not actually doing the job, may signiﬁ cantly reduce the exposure level

! protect yourself against the effects of vibration by

maintaining the tool and its accessories, keeping your hands warm, and organizing your work patterns

Perceuse 1450 INTRODUCTION

• Cet outil a été conçu pour couper le gypse, le bois, le plexiglass, le plastique et les carreaux muraux mous

• Lisez et conservez ce manuel d’instructions 3

ENVIRONMENT

• Do not dispose of electric tools, accessories and packaging together with household waste material

(only for EU countries)

SPECIFICATIONS TECHNIQUES 1

Skil 1450 Instruction Manual

Specifications and Main Features

Frequently Asked Questions

User Manual