Singer Sewing Machine User Manual

Easy PipingICording

Materials Required:

> SINGER®Serger
> SINGER

®

cording foot for serger
> Fabrics of your choice
> 3-4 Cones of overlock thread
> SINGER® overlock needles
> Piping (available in stores)
> Thread for tacking, if required

1

Preparing the Serger:

3

Let’s Start Sewing:

1 I

> Attach (snap-on) the

cording foot

> Set the stitch length

to »N«

> The stitch width

should match the
piping width

> Set the differential

feed to »N«
(if applicable)

> Thread the needles

(3 or 4, depending on the material used)

> Set the needle(s) at the highest position

4 I Professional piped corners – not only for the »experts«!

It only takes a little practice to finish corners with an exquisite
piped trimming. Stop sewing approx. 3 cm away from the
seam end. Place the piping across the corner.Doing this, the
piping may form a soft
»wavy line«.Continue
sewing right up to the
corner and raise the
needle. Slightly raise the
presser foot and pivot
the fabric. Lower the
presser foot and then
lower the needle – as
closely to the last sewn
stitch as possible.Finish
the seam.

3 I Line up the piping
with the groove in the
presser foot. Make sure
to line up the edge of
your fabric along the
upper knife.With every­thing properly aligned,
start sewing. While the
fabric layers are joined
together,the piping is
simultaneously attached
between the fabric
layers.Make sure that the piping follows the groove of the
cording foot while sewing!

Sewing piping (cording) as edge finishing:

Piped edges look as exquisite on curtains and table linen
as they do on clothing! When working with light-weight
materials there is no better way than piping to give the
fabric a heavier and firmer finish.

Tack the piping on the
fabric so that the edge of
the piping lines up with the
raw fabric edge.Stitch the
piping in place.

Fold in and press along the
stitch line of the piping and
make sure that only the
piping is visible after
pressing.

Stitch in place the seam
allowance using your
sewing machine.We re­commend to use the zipper
foot with a left needle
position (as far left as you
can go).

Tip! Whether to choose a 3 or 4-thread overlock

stitch depends on the fabric type and size of the
piping. The basic rule is:For sewing firm,heavy­weight materials select a 2-needle/4-thread over­lock seam,for sewing light-weight materials choose
a 1-needle/3-thread overlock seam.

!

Important! Remember that you need different size

needles when working with different types of
materials.This basic rule also applies to sewing
piping! Stretch materials should be sewn with ball
point needles,heavy fabrics with larger-size needles,
etc. Following this simple rule will lead to neat,
professional results.

!

Have you ever tried to use piping for creating lavish decora­tive effects? It’s just as fast and easy! Follow your inspira­tions and use a multitude of different colors and materials
– for intriguing results!

On the right fabric side
stitch in place the differ­ent rows of piping with
different spacings.Fold
in the piping so it covers
the seam allowance.
Press the fold and top­stitch in place using
your sewing machine.
You’ll be stunned by the
beautiful textured,
striped adornments!

Stripes with a difference!

Fancy stripes for every taste!

Piped seams are nothing unusual on upholstery,
cushions or curtains. They’re not only great-looking
trimmings, but give seams additional strength and
durability. Accenting clothes with piped edges is just
as pretty and practical: Used on casual jackets or
pants, children’s wear and even elegant evening
wear – piping has a huge variety of applications to
enhance your sewing projects.

Piped edge finishings always give your work a
professional touch – and they’re so easy to sew with
your SINGER

®

serger.

Stitch program:

Select a 3 or 4-thread overlock stitch

2

Preparing the Fabric:

The Serger

Using a serger is the easiest
way for producing beautiful
piped edge finishings.Its
special cording foot lets you
sew and finish piping between
multiple fabric layers in one
easy operation.And the serger’s
multiple-thread overlock seam
provides an extra-strong rein­forcement for heavier-type fabrics!

The piping (cording) follows the groove of the cording
foot as you sew, thus preventing displacement of the
piping. As a result,you’ll achieve precise and evenly sewn
piped seams that really look professional!

The Piping/Cording Foot

The secret of
piping:

Piping,
closed edge

W

rong fabric side

Right

fabric side

Important!

Don’t use pins to avoid damage to the serger’s
upper knife! Always tack slippery fabrics,never pin
in place.

!

How to prepare your own piping:

It may be difficult at times to buy piping that matches
the fabric for your planned project.Don’t worry! You
can make your own piping in just a few simple steps:

> Fold in half store-bought

bias binding or bias-cut
fabric strips
(approx.4 cm wide).

> Place the cord of your choice

in the center of the folded
bias binding.

> Tack in place the two fabric

layers of the bias binding,as
close to the cord as possible,
so the cord can no longer slip
out.

Using your sewing
machine with attached
zipper foot,topstitch along
the tacking line and through
the two layers.The zipper
foot ensures even feeding –
for guaranteed perfect
results!

Cord

Seam edge

2 I

Sewing piping (cording) between two layers of fabric:

> With right sides together,place the piping between the

two layers of fabric.

> The edge of the piping must line up with the raw fabric

edges and lay towards the inside of the fabric.

> Best results are achieved

by tacking the piping on
the bottom fabric layer
first and then placing the
upper fabric layer on top
(tack again, if desired).