Sinclair AW-12A Instruction Manual

Instruction Manual

PLEASE READ THE INSTRUCTION MANUAL CAREFULLY BEFORE USING THIS UNIT.PLEASE READ THE INSTRUCTION MANUAL CAREFULLY BEFORE USING THIS UNIT.PLEASE READ THE INSTRUCTION MANUAL CAREFULLY BEFORE USING THIS UNIT.

Table of Contents

1.Safety Cautions 1

2.Configuration 2

3.Assemble and disassemble 4

4.Operating instrutions 10

5.Maintenance 13

6.Technical parameters 14

7.Troubleshooting 15

8.Loading List 16

THROUGH-WALL AIR CONDITIONER

Model

AW-12AAW 12A-

1 2

Safety cautions

Configuration

■ SAFETY WARNING ■ BODY CONFIGURATION

■ Component configurationComponent configurationComponent configuration

1.Control Panel

2.Display Window

3. Indoor Outlet

4. Adjustable Foot pad

5. Indoor Inlet

6. Outdoor Outlet

7. Outdor Inlet

8. Drain

9. Handle

1.Drainpipe external joint

2.Drainpipe

3.Drainpipe internal joint

4.Screw

5.Cushion

6.Drainpipe Connecting rod

7.Drainpipe external joint hook

8.RemotE controller

■ PRECAUTIONS

●Do not use this product near open flame、Inflammable and explosives.

●To avoid the possibility of any damage ,do not beat、Crush or shake this machine.

●Do not cover or block the inlet and outlet in case of any potential hazard caused by
over-heating of this machine

●To avoid the possibility of electrical Shock, make sure this machines is not easily exposed
to water

●Make sure the professional Electric Personnel or service agent IS sended for maintenance
When the power cord is damaged.

●Do not alter the length of the power cord or share the socket with other eleCtric appliances.

●To avoid the possibility of electrical shock, do not unplug with wet hands.

●Do not insert sticks or other objects.

●Do not use altered power cord plug.
Do not allow Children playing around.●

●Please place this machine 1m away from the TV and radio to avoid the possibility of

electromagnetic interference.

●Do not place This machine in the sun to avoid the fading of the surface.

●Make sure the angle of inclination is less than 35°While transportation , 5°While operating；

●This macHine can not be used in certain rooms(more detailed information in the technical

parameters)

●Do not use chemical solvent to clean the surface to avoid the possibility of any SCRATCH,

DAMAGE and deformation.

Make sure the condenser water IS fully discharged during Removal or inclination to avoid
any leakage.

●

1
2

3

4

5

6

7

9

8

7

6

5

4

1

2

3

8

3

4

Assemble And Disassemble

■ DISPLAY SCREEN SYMBOL SPECIFICATION DISPLAY SCREEN SYMBOL SPECIFICATIONDISPLAY SCREEN SYMBOL SPECIFICATION ■ ASSEMBLE

■ OPERATION BUTTON SPECIFICATION

DISPLAY SCREEN

111098

7654321

1.AUTO

1.Put the machine in Place, ADJUST the nut to keep the machine horizontal; Any inclination

will cause Inadequate passage of water in the machine.

2. Drill a hole in walls in accordance with the position of the DRAINPIPE (As illustrated in

the picture)

2.COOLING

5.FAN SPEED

3.DEHUMIDIFICATION

11.WIND DIRECTION

1.TEMPERATURE/WIND SPEED DOWN

2.TEMPERATURE/WIND SPEED UP

3.TIMING

4.SLEEP

5. AUTOMATIC SWING

6. WINDSPEED

7. MODE

8. ON/OFF

9. CONTROLLER ACCEPTANCE WINDOW

10.SLEEP

7.HEAT

6.FAN SPEED

8.SETTLE THE HOUR

9.TIMER

4.TEMPERATURE

1 2 3 4 5 6 7 8 9

Configuration

Nut（4）

TEMP/DOWNTEMP/DOWNTEMP/DOWN TEMP/UPTEMP/UPTEMP/UP

TIMETIMETIME

SLEEP SLEEP SLEEP

WIND WIND WIND

SPEED SPEED SPEED

MODE MODE MODE

ON/OFFON/OFFON/OFF

5 6

Assemble And Disassemble Assemble And Disassemble Assemble And Disassemble Assemble And Disassemble

3.Place the drainpipe（L=482mm）In waist-shape hole,beyong the external wall 5mm;

NOTE: The length of the drainpipe can be incised in accordance with the thickness of
the wall (Ex. the thickness of the wall W=300mm, 482+23-300-5=200mm can be incised)

4.Wrench the drainpipe external joint hook into the drainpipe external joint

5.Stretch beyong the wall through the macropore in the drainpipe

6 .Pull the drainpipe external joint in walls to make it coordinate with the drainpipe;

7 .Stretch the drainpipe Connecting rod to a certain length beyond the wall Through the rail

alongside the drainpipe, then RotaTe 90°And pull inwards horizontally till the limit;

8 .Accomadate the drainpipe internal joint into the drainpipe through drainpipe connecting rod.

In walls

beyond walls

23mm

5mm

7 8

Assemble And Disassemble Assemble And Disassemble Assemble And Disassemble Assemble And Disassemble

9.Cushion into the connecting rod for air exhaust duct, and fix screw.

10.Disconnect the excessive drainpipe connecting rod;

The following procedure can be applied when the machine is to be fixed on the wall (at the
request of the customers)

1.Push hard the tab to the back of the machine, rotate the air-inlet grille and remove it;

2.Remove the filter, release the screw, and remove the air-inlet frame;

Push

Filter

Screw

Air-inlet

11.Another drainpipe connecting rod follows 7-10

12.Push the machine into the hole on the wall (the heihgt of the screw can be adjusted to

facilitate the process).

9 10

Assemble And Disassemble Assemble And Disassemble Operating Instructions Operating Instructions

3.Push upward the front shroud and then forward, then remove it;

4.Sew on the screw st5x8 and fix it;

●OPERATION BUTTION SPECIFICATION: (the buzzer will make a “D”sound when pressing
The button and the operation is effective.)

1.When the electricity is on ,the machine Will make two “D D”Short Sound, press the button ,

the machine is on; press again , the machine is Off; turn on the machine after the machine
halts, 3 minutes automatic protection will be on.

2.For setting the operation mode, in accordance with the following order:

4.TEMP/UP AND TEMP/DOW N：to set temperature and timing

（1）Set the temperature, once pressing the button TEMP/UP TEMP/DOWN, the
temperature climbs or falls 1℃; when the indoor temperature is displayed on LED,
when first pressing the button, it will switch to the display of setting temperature, after
that, every time when pressing the button, the temperature climbs or falls 1℃;5 seconds
after the operation, LED will re-display the indoor temperature;
（2）When in the time setting position, every time when pressing TIME/UP TIME/DOWN,
the time gains or looses 1 hour, the time being 0-12 hour circulating setting,5 seconds

after the time setting, it will fall into timer position; if the current setting is 0 hour,5seconds
after the time setting ,it will quit the timing position.

5. TIMER：
（1）To set the machine on, pressing the button can set timing shutdown, pressing the
TEMP/UP TEMP/DOWN can set timing shutdown;re-pressing the button when the timing
is not determined will cancel timing shutdown; during timing shutdown, the customer can
shutdown the machine manually to cancel the timing shutdown;
（2 To set the machine off, pressing the button can set the timing start, pressing the）
TEMP/UP TEMP/DOWN can set the on time; press the button again when the timing is not
determined can cancel the timing shutdown, the customer can shutdown the machine
manually to cancel the timing shutdown;

6.SWING：

Press the button will switch between automatic swing and swing halt, the swing angle being
120°;The swing wind is simultaneous with the internal wind machine switch.

7.SLEEP：

(Sleep can only work when the cooling and heating mode is on, sleep will automatically cancels
when restart) when the sleep is on, the internal wind machine will automatically switch to low wind.

A.When the cooling is on: after 1hour,the set temperature climbs 1℃;2 hour later, it climbs
another 1℃;6 hours later, off;

b.When the heating is on; after 1hour,the set temperature falls 1℃;2 hour later, it falls another
1℃;6 hours later, off;

5. Assemb le the disassemb led parts following the compleme ntary procedures.

Disassemb le

1.If the machine is fixed on the wall, disassemble the air-inlet frame and front cover, then

wrench the screw;

2.Remo ve the ma chine;

3.Loose the screw, and remo ve the fixed connecting rod cover and drainpipe internal joint

4.Loose the drainpipe connecting rod and rotate 90°,remove alon the rail alongside the drainpipe;

5.Remo ve the drainpipe from the drainpipe;

6.Remo ve the drainpipe.

AIr-inlet

Scre

low speed wind

edium speed wind

igh speed wind

auto

cooling

ehumidification

entilation eating

3.3.

d v

h

h

m

11 12

●Remote controller operation ●How to assemble batteries and set the time

1.Auto

2.Cooling

3.Dehumidification

4.Ventilation

5.Temperature

6.Highspeedwind

7.Mediumspeed wind

8.Lowspeed wind

9.Auto swing on

10.Auto swing off

11.Time

12.Sleep on

13.Timer on

14.Timer off
15Timing.

1.open back cover

2.place the batteries into the slot, pay attention to the two poles.

3.press the button as illustrated in the picture

4.set the time flash

5.adjust the hour button
6press the button as illustrated in the picture again when the time is set, the
setting is completed when the time display symbol stops flashing.

.

Notes:

1．The positive pole and negative

pole of the battery must correspond
with the respective pole on the
controller.
2．Do not mix the new batteries with
the old ones.
3．Please remove the batteries when
the controller is not to be used for a
while.
4．To avoid environmental pollution,
make sure the batteries are removed
before deserted, and arrange them
properly.

● How to operate with the controller

There are two methods to use the controller to operate the auto、cooling、heating、
dehumidification、ventilation mode:

1. Select the operation mode>> adjust the setting temperature>> adjust the wind speed >>.
off (this method is same with the operating instructions of the operating panel)

16.Mode
17Temp/ up

18.Temp/ down

19.Wind speed

20.Swing

21.Time hour

22.Time minute

23.Sleep on/off

24.Timing

25.On/off

LCD display screen

Operating instructionsOperating instructions

Operating instructions Operating instructions

1

2

3

4

5

6

13 14

Technical parametersTechnical parameters

1．Remove the air-inlet grille; remove the filter from back of the machine;
2．Soak the filter in 40°C or so mild water contain netural detergent to clean, dry it in the
shades;
3．After dried put the filter back to the back of the machine and close theair-inlet grille.

Notes:

1.To avoid the possibility of any electrical shock, make sure the machines is shutdown and
the socket is unplugged before cleaning;

2.If the air output decreases due to the pile-up of dust in the filter, it is suggested the filter
cleaned every other month.

Drainage

When the machine is on the cooling position, the condenser water will bedischarged into the
chassis, auto-alarm will be on when the chassis is filled with water, the buzzer beeps for 20
seconds, LED display screen will display E4; meanwhile the cooling system is off. The indoor
inner wind machine will shut after 3minutes, please unplug the rubber plug alongside the
machine for drainage if more cooling is needed.

● continuous-drainage

Please select this method when the machine will be use for a while;

1. Unplug the rubber plug alongside the machine as illustrated in the picture. Place it
carefully for further usage.

2.Connect the drainpipe to the drain as illustrated in the picture. The condenser water will
be discharged from the drainpipe.

4. PVC pipe with inner pathway of 8mm can be connected to the drainpipe. If the drainpipe

3. Take the drain pipe connect with drainage.

is to be lengthened.
Notes; the drainpipe shall be parallel with or lower than the drain.

■ FILTER CLEANING

Model

Rfrigerating capacity (Btu/h)/（W）

12000/3500

Heating capacity(Btu/h)/（W）

12000/3500

Dehumidification capacity (L/h) 1.8

Heating input power (W) 1500

Refrigerating input power (W) 1300

Circulating input air (m³/h) 400

power(single-phase) (V~/ Hz) 230V/50Hz

Noise dB (A)

≤52

Net weight (kg) 47

body (mm) 610×285×825

Body package (mm) 685x370x885

Dimensions

Accessories package

(mm)

420X230X525

Refrigerant Charge R410A / 790g

Applicable area(m²) 20~25

Notes: since the high updating speed of the products, revision of Technical parameters will

not be otherwise notified.

AW- 12 A

MaintenanceMaintenance

Device is not intended for continuous running.

15 16

Loading listTroubleshootingTroubleshooting

Before maintenance request, please check the machine with the following methods:

the machine can not start

The machines stops
automatically

No cool air when cooling
position is on

No hot air when heating
position is on

LED “E1”

LED “E2”

LED “E3”

LED “E4”

LED “E5”

Power troubles:

1. the power cord is not plugged

2.the power cord or socket is damaged

3.The fuse is cut off

Timing off time is up or the indoor
temperature is lower than the set
temperature

1. Iindoor temperature is lower than the
set temperature
2 The indoor temperature is too low and
causes anti-frozen protecti on

.

1. Tthe indoor temperature is higher than
the set temperature
2Defrosting.

lack of coolant

indoor temperature sensor out of
order or damaged

indoor coil sensor out of order or
damaged

chassis filled with water

outdoor coil sensor out of order or
damaged

re-start after adding coolant

change indoor temperature sensor

change indoor coil sensor

Discharge the chassis

change outdoor coil sensor

1. This is normal, it will start
automatically when the indoor
temperature is higher than the set
temperature

2. The machine will start automatically
after defrosting.

This is normal, the machine will start
automatically when after defrost or
indoor temperature is lower than the
set temperature.

Close timing shutdown or wait until
machine starts

1.Plug the power cord

2. Change the power cord or socket

3. (Specification：3.15A/250V).ask
the local after-service agent to change
the fuse

TROUBLES CAUSES SETTLEMENT

No.1

BODY PACKAGE COMPONENGS NAME

QUANTITY

1.1 Mobile air conditioner 1

1.2 Controller 1

1.3 Specifications 1

1.4 Drainpipe(1.5m) 1

No.2

ACCESSORIES PACKAGE COMPONENGS NAME

2.1 Drainpipe internal joint 1

2.2 Drainpipe external joint 1

2.3 Drainpipe 1

2.4 Drainpipe connecting rod 2

2.5 Drainpipe external joint hook 1

2.6 M3 screw cushion 2

2.7 Universal wheel 4

2.8 Spanner 1

2.9 Drainage pan 1

2.10 Drain connective pipe 1