Sinclair ASH-09AQ, ASH-18AQ, ASH-13AQ User Manual

USER'S MANUAL

ASH-09AQ, ASH-13AQ, ASH-18AQ

QUEEN SERIES

Usage Notice (Please read the following notice carefully before usage)

WARNING

Ensure power plug had

fire may occur.

be inserted firmly.

Don't plug out power plug

when unit is operating.

fire may occur.

Otherwise electric shock or

Don't damage wire or use
the wire that is not appointed.
Otherwise electric shock or

fire may occur.

Don't share socket with

other appliances or use

electric shock or fire may

prolonged hose. Otherwise

Don't operate unit with wet

hand for electric shock may

Don't insert finger or stick­like thing into air outlet vent
of indoor and outdoor unit.

Don't let cooled air blows

body directly for too long, and

don't set indoor temp. too low

If abnormal phenomenon

occurs (like burning odor etc),
cut off power supply first, then
contact our service center.
If abnormal continues, the unit

may be damaged and cause

Don't repair the unit yourself

for incorrect repair may cause
electric shock or fire. Contact
our service center to have

Cut off

Otherwise electric shock or

occur.

occur.

Or it would cause harm.

for it is not good for health.

electric shock or fire.

the unit repaired.

power

－１－

★

Earthing: Earth must

be reliable! Earth wire

should be connected on special

If there is no such settings, have
it connected by perfessional
personnel. Don't connect earth

earth settings in the building.

wire onto gas pipe, water pipe,

★Plug out power plug when

the unit will not be used for a

★

Cut off power when cleaning

the unit. Otherwise, electric

shock or damage may occur.

Otherwise, fire may be caused

★Don't take out the plug by

pulling the power hose.

for over heat of wire.

★Don't let the unit blows to

CO toxicosis may occur for

heater or cooker directly. Or

imcomplete burning.

★Chemical sprayer must be

placed 1m or more away from
both indoor and outdoor unit.

damaged

without repair, unit

★Note if install chassis is

damaged. If the chassis is

may fall down and cause

or things may fall down and

★Don't stand or put things

on the outdoor unit. For people

cause injury.

★

Don't block the air intake or

outlet vent of both indoor and

outdoor unit. It would cause

low performance or stop of

blowing pipe or places where
perfessional personnel
considers it unrealiable.

long time.

Otherwise fire or explosion

may occur.

injury.

unit.

－２－

Name of Every Part of The Unit

◆

Button ON/OFF

Wire connection

Power plug

cover plate

Panel

Displayer

Wireless remote control

Filter

Guide louver

Air in

Air out

Air in

Air out

High

Medium

Low

Displayer

All on in Auto

Swing

Sleep

Dry

Fan

Window

Receive

Air purifying

Air outlet grill

Unit

Drainage hose

Outdoor

Static dust catcher

Connecting pipe

and connecting
wire

Indoor Unit

－３－

(functionless for this model)

Name and Function of Every Button on Wireless Remote Control

Usage Method of Wireless Remote Control

between the two sides; don't drop or throw the control; don't flow any liquid

Ensure the control is aligning receive window, and there is no obstruction

Note:

●

　Press this button then the unit begins

running; repress unit stop running and

ON/OFF button

ON/OFF

cancel Timer at the same time.

(Note: Cooling only units have no

mode.)

●

　Press MODE and run mode changes

Mode

Mode selecting button

according to following order.

“　　　”Dry
“　　　”Fan
“　　　”Heat

“　　　”Cool

Display

Display of every mode

●

　Every press of , set temp. raise 1℃.

Under mode, set temperature can be

set between 16~30℃.
Under mode is between 16~30℃.
Under mode 16~30℃.

Every press of , set temp. lower 1℃.

Temp.

Temperature button

When transmitting and

●

　Every press of the button, fan speed

Fan

Fan speed cannot be changed when Drying.

changes by following order:

PCB receives it as High speed. Note:

Low is displayed as and Medium as

, High displayed as and

Fan button

Swing

Auto Swing

by 7 swing states below.

Stop

Left and right swing button

Wireless

“　　　”Sleep

Signal transmit terminal

●　Under mode, the recommended set

temperature is 24~26℃.

Under mode is 19~23℃.
Under mode is 20~24℃.

Note: When unit is turned on after turning
off by wireless remote control, the control
would remember the set swing position set

●

　Every press of , swing mode changes

into it or place it under direct sun burn or where there is extrimely hot.

remote

control

Auto

Auto

at last operation.

－４－

Name and Function of Every Button on Wireless Remote Control (Remove Cover)

◆

Note: This kind of wireless remote control is the general one that is suitable for several

models (functions). Please understand that we won't introduce the buttons that

When Cool and Dry is running: After

Sleep

●

　Press the button once to be in Sleep

Note: There is no Sleep function under

raise 1℃, 2 hours later set temp. raise

When Heat is running: After running of

and 2 hours later lower 2℃, then unit
runs by this set temperature.

state and repress to exit.

running of Sleep for 1 hour, set temp.

2℃, then unit runs by this set temp..

Sleep for 1 hour, set temp. lower 1℃,

Auto and Fan mode.

Sleep button

Timer button

●

　Press this button and Timer Off (or On)

blinks and display last set time. Press +
or - at this time can set Timer time (press
+ or - for a long time to increase or decrease
time rapidly). The set ranges from 0.5-24
hours; repress the button to confirm the
time and transmit and Timer Off (On) sign
stop blinking. If the sign is blinking but no
Timer Button is not repressed, former set
state would be resumed automatically after

10s. When unit is on, press this button can
set auto off time; and auto on time can be
set when unit is off. When Timer is set,

Timer

control

are not available to this unit.

remote

Wireless

press the button once to cancel.

Displayer

●

　Displays selected information of every

LCD

Upper and lower swing button

Auto Swing

Stop

Swing

Light button

●

　Press once then displayer on, repress

is not controled by this button (This button

to make it off. Lights of mode and sleep

Light

mode changed according to 7 swing

Guide louver swings according to above state.
Note: When the unit is turned on after being turned
off by wireless remote control, the unit remembers

●

　Every press of , displayed swing

selected button.

state below.

the swing position of last operation automatically.

is not available when unit is off).

－５－

◆　Change of Batteries of Wireless Remote Control

1. Slide the battery cover downward to take out worn batteries, then change 2 new

2. Cover battery cover.

Note:

●Don't confuse the new and worn or

●If wireless remote control will not be used

for several weeks, please do take out

batteries to prevent leakage of liquid from

●Operation of the control should within its

receivable area.

●The control should be 1m or above away

from TV or hi-fi equipments.

Reset

Insert 2 AAA batteries

Wireless remote control use 2 AAA dry alkaline cell

different types of batteries.

Batteries cover

ones (note the correct polarities).

damaging the control.

8. Press TIMER and then

/

to set Timer on or off time.

◆　　Operation Guideline

Common process:

1. After connecting with power, buzzer sounds and indoor unit displayer displays all signs. Several
seconds later all indicator signs off automatically except power indicator sign, then only power indicator

2. Press ON/OFF on wireless remote control, power indicator light off and present set running mode
set temperature and fan speed etc are displayed at the same time, unit begins running (Note: After

3. Press MODE to select proper running mode.

4. Press SWING to select swing mode or fix the air supply in a certain direction. When Swing is operating,

5. Press FAN to set fan speed.

Optional process:

7. Press SLEEP to set sleep state.

Note: When AUTO mode is selected, the unit would select proper operation mode
according to indoor temperature to make ambient comfort.

6. Press TEMP to set proper temperature.

light on and displays in green. The unit is in waiting state (Note: When every electrified or received

signal from wireless remote control, buzzer sounds; every electrify, both guide louver and swing

louver reset automatically).

turning off light, all signs except running indicator sign off).

Swing indicator light on, otherwise the light off.

－６－

Align proper set temp. can avoid electric

Indoor temperature should be set in proper

Don't water or wash the unit by water, it

could cause malfunction or electric shock.

This unit adopts X-connection power cord, please

don't cut or damage power cord and signal control

wire. If the cord and wire are damaged, do have

them replaced by professional personnel.

This unit cannot be used for drying clothes and

refrigerating foods etc.

★Don't open the doors and windows for a

long time when unit is running.

When unit is running, press the Swing on wireless remote

★Align proper airflow and direction

control for left and right swing can align airflow horizontal

direction, press Swing for upper and lower swing can align

★Don't let the unit blow against pat and plant

directly, for it is not good for them.

★The allowed voltage flucture of this unit

is 230±10%V. The strong shocking of
compressor caused by too low voltage

Temp. dif.

and outdoor

Or the capacity of unit would be decreased.

Left and right air direction

Upper and lower direction

Users' Notice

wasting.

between

indoor

should be 5℃

airflow vertical direction.

aligning louver

aligning louver

would damage cooling system.

50Hz~230V

－７－

Maintenance

◆

▲Turn off the unit and take out the power plug before cleaning the unit, or
▲Don't make the unit wet, or electric shock may occur, ensure that the unit

would not be washed by water under any circumstance.

▲Volatile liquid like thinner or gasoline would damage the appearance of the

unit (Only adopts soft dry cloth and wet cloth moisted with neuture cleaning

Take off and clean the panel

1. Take off the panel by pulling the grooves of both

ends to the shown position in figure at the same

2. Clean

3. Install panel

Insert the supports on 2 ends of panel into groove,

and put the mid rotating shaft in groove, cover

the panel cover according to arrow direction and

Clean air filter (Once about 3 months)

If the usage environment of the unit has lots of duct, the cleaning of air filter should

1. Take off air filter

Pull out the panel to an angle at both grooves on

panel forcibly at the same time, then pull the air

filter downward to take it off. As shown in right

Clean it by soft brush, water and neutral cleaning

fluid, then swing water or dry it (Note: Take off

LCD box before cleaning panel to prevent

damaging the box by water leakage. Don't

water it by hot water whose temperature is higher

than 45℃ to prevent fade or deformation).

（ａ）

（ｂ）

electric shock may occur.

fluid to clean appearance of the unit.)

time by the arrow direction.

cover it well.

be more frequently.

figture.

－８－

Check before usage season

1. Check if the air intake or outlet vent of indoor or
outdoor unit is blocked.

2. Check if earth wire is connected firmly.

3. Check if batteries in wireless remote control is

4.

Check if install support of outdoor unit is damaged,

if so, contact our service center.

Maintenance after usage season

1. Clean filter and body of indoor and outdoor unit.

2. Cut off power supply of the unit.

3. Clear dust and things on outdoor unit.

4. If outdoor unit rusts, paint oil paint on rust to

prevent spreading.

2. Clean air filter

Adopt ductcollector or water to clean filter. If the
filter is too dirty (like oil spot), clean it by warm water

(lower than 45℃) melted with neutral cleaning fluid

Note: Don't wash it by hot water whose temp. is

higher than 45℃ to prevent fade or deformation. Don't

3. Install air filter

Insert the air filter, then cover panel cover well.

then dry it in shade as shown in right figure.

dry it on fire for filter would catch fire or deformation.

replaced.

－９－

Water flow sound is heard when the unit is

This is the sound of flow of refrigerant inside the

When cooling, mist comes from air outlet vent.

This is because the indoor air is cooled rapidly.

This is the frictional sound caused by expansion of

panel etc since the change of temperature.

Slight creaking noise can be heard when the

Phenomenon Troubleshooting

Odor comes out from the unit when it is just turned

This is the odor of furniture and cigarette that sucked

in the unit when it was working and now be blown out.

The unit cannot be restarted immediately after

Once the unit be restarted immediately after turned

off, overload protect switch would make it run after

Troubleshooting

◆

Warning: Please don't repair the unit by yourself for incorrect repair would cause

electric shock or fire; please contact our service center to have the unit
repaired by prefessional personnel. Check the following items before
requesting on service center would saves your time and cost.

being turned off.

3 minutes' delay.

on.

operating.

unit.

unit is turned on or off.

－１０－

Stop the unit from operating immediately and plug out power

plug then contact our service center when following circumstance

▲Harsh noise is heard when the unit is running;

▲Air switch or creepage protector always trip;

▲

Water or other things poured into unit or wireless

▲Water leakage occured in room;

▲Power cord and plug are extremely hot;

▲Abnormal odor is produced when unit is running.

Please contact

service center if there

is problem.

·Is power supply cut off?

·Is power cord loosen?

·Is circuit protect setting triped?

·Is voltage too high or too low?

·Is Timer On set by wireless remote control?

·Is temperature set in proper?

·Is air intake or outlet vent of outdoor unit blocked?

·Is there too much dust on air filter?

·Are windows and doors closed?

·Is airflow set to Low?

·Is there any heat source in room (when cooling is

·

When unit is interfered by abnormal interference or

too frequent of change function, wireless remote

control would not control occationally. Plug out power

·

Is the control in receive area? Or is there onstruction?

·Check if voltage of batteries in the control enough?

If not, change batteries.

Phenomenon Troubleshooting

Trip

☆　Please refer Warranty for relative items.
☆　If there is any question about quality or others of the unit, please contact

the service center.

Wireless remote control cannot control

Bad cooling (heating) effect of the unit

The unit cannot run

·Is wireless remote control damaged?

Trips

bad)?

plug and reinsert it well could resume normal operation.

occur.

remote control carelessly;

－１１－

1. Air intake and outlet vent should be far away from abstruction so that airflow could

Indoor unit

2. Select the place where is easy to drain condensate and connect with outdoor unit;

3. Far away from heat source, steam and flammable gas;

4. Select the place where is strong enough to stand the weight of indoor unit without

5. Ensure enough space for maintenance and repair, ensure the height from floor

6. Place where is 1m or more away from TV, hi-fi and other household appliances;

7. Place where air filter can be taken out easily;

8. Ensure the installation of indoor unit fits requirements in Install Dimension Diagram.

Outdoor unit

1. Place where noise and airflow from the unit would not disturb neighbors;

2. Place where there is well ventilation for outdoor unit;

3. Obstructions are not allowed to exist around intake or outlet vent of outdoor unit;

4. Place where can stand weight and shake of outdoor unit and ensure safe

5. Place where there is no leakage of flammable gas and corrosive gas;

6. Ensure the install of outdoor unit fits the requirements of Install Dimension Diagram.

◆　Select of Install Location

Install Service

be blown to the whole room;

increasing operation noise and shake.

to indoor unit over 2m;

installation work;

－１２－

◆　Wire Allocation

1. Install according to national wiring regulation.

2. Power must adopt rated voltage and special circuit for air conditioner, diameter of

4. Earth should be connected reliably. Connect it on special earth settings of the building

and do have it done by professional personnel. There should be creepage protecting

switch and air switch with enough capacity in rated circuit (refer to following list). Air

Capacity of

air switch

Min. section

of earth wire

Min. section of

power cord

◆　Earth Requirements

1.

Air conditioner is type I electric appliances, please do conduct reliable earth connection.

2.

The yellow-green wire in the unit is earth wire, don't use it for other purpose and

don't cut it. Don't fix it by self tapping screw or electric shock may occur.

3. Earth resistance should fits requirements of National Criteria GB17790.

4. User's power must offer reliable earth terminal. Please don't connect earth wire

①　Water pipe ②　Gas pipe ③ Drainage pipe ④ Places where professional

Usage Models

3. Please don't pull power cord forcibly.

power cord should be big enough.

switch should contain magnetic dropout and heat dropout functions to guarantee

protection when circuit-short and overload occur.

onto following places:

personnel considers unreliable

ASH-12AQ

１０Ａ

１．０ｍｍ

２

１６Ａ

１．５ｍｍ

２

１．０ｍｍ

２

１．５ｍｍ

２

－１３－

ASH-18AQ

1６

Ａ

１．５ｍｍ

２

１．５ｍｍ

２

ASH-09AQ

◆　Install Dimension Diagram

Important Notes

★To ensure good usage, install the unit by professional personnel according to this instruction.

★Please contact our local service center before installation, malfunction caused by the unit that

was not installed by our service center would be hard to deal with in time for inconvenient

★It is better to be guided by professional personnel when moving the unit to other place.

Distance to floor

Exhaust side

Distance to ceiling

Distance to wall

Distance to wall

Air in side

Exhaust side

Distance to cover

Distance to wall

Distance to wall

or more

15cm or more

15cm or more

or more

or more

business contact.

－１４－

☆　Install Rear Plate

☆　Open Pipe Hole

1. Measure horizon by hanging line or horizontal measurement. Since drainage pipe hole is on

left, it is better to make left side lower.

2. Fix rear plate on wall by bolts.

3. Pull the rear panel by hand after
installation to see if it is firm enough.

Fig. 1

Left

Distance

The panel should be able to stand

Wall

１５０ｍｍ

φ６５ｍｍ

Right

Shown in middle Gradienter

８３０ｍｍ

１８０ｍｍ

１２０ｍｍ

２８４ｍｍ

(Rear pipe hole)

the weight of an adult (60kg) and

Wall

Distance

φ６５ｍｍ

(Rear pipe hole)

or more

１５０ｍｍ

or more

the weight should be evenly shared

1. Drill a hole outward at a slant after pipe hole is determined as

shown in fig.1 (Ф

65).

rats in the space, put on wall pipe.

Indoor Outdoor

Wall pipe

Sealing clay

Ø

６５

◆　Install of Indoor Unit

☆　Install Drainage Hose

1. Drainage hose must be placed at a downward slant
for smooth drainage.

end by water.

3. The indoor part of prolonged hose should be wrapped

Wrenched

Bent

Don't flood it

☆　Install Connect Pipe

1.

Connect the connect pipe with 2 leading pipes of indoor unit, then tighten joint nuts on connect pipe.

2. Tighten nuts on connect pipe forcibly, and then tighten it by spanner.

Note: Too great of torque would damage nuts.

Refer the following list for tighten torque.

Note: Connect the connect pipe with indoor unit first and then outdoor unit; bend and place of

pipe should be careful to prevent damaging the pipe; joint nut should not tighten too much

Hex nuts Tighten Torque (N·m)

Ф６

Ф９．５

Ф１２

３１～３５

１５～２０

５０～５５

by each screw.

to wall

side

to wall

side

2. In order to protect pipe and cable from being damaged and avoid

2. Don't wrench, bend or heave the hose or flood its

by heat insulating material.

Pipe of indoor unit

Nut

Pipe

Spanner

Wrench torque

or it would cause leakage.

in water

－１５－

4. Connect the blue wire among power connect wires onto terminal N(1) on line bank, black

wire onto terminal 2 and yellow-green one (earth wire) onto terminal (as shown in fig.4).

5.

Put the section of power connect wire with sleeve into clamp groove, cover wire cover plate,

screw on fixing bolts to tighten the wires.

7. Cover panel.

6. To cooling and heating unit, signal control wire connect with indoor unit via connector, and

has the wire tightened by clamp at bottom of the unit's body (as shown in fig. 5).

Wire cover plate

Power

Connect

Fig. 3

Linebank

Power connect wire

Fig. 4

☆　Electric Wiring

1. Open panel upwardly (as shown in fig. 2):

2. Take off fixing bolts of wire cover plate to take off the plate (as shown in fig.3).

3. Make power connect wire goes through the single wire hole at rear side of indoor unit and

Fig. 2

Note:

If the connecting wire was not long enough, please contact the appointed service shop to
match another special wire that was long enough. Don't prolong wires.

●

　Don't connect wire in wrong for it would cause malfunction on some components.

●

　Tighten bolts to prevent loosen of them.

●

　After tighten bolts, pull wires slightly to see if they can be moved.

●

　Electric shock may occur when earth wire is connected wrongly.

●

　Wire cover plate should be fixed well and tighten connecting wires. If the plate is

not installed well, dust and moisture may get in or cause fire or electric shock for

Signal control wire (only for cooling and heating unit)

Clamp

Fig. 5

pull it in front side.

wire

Blue

Black

Yellow-green

terminals were affected by outside force directly.

－１６－

◆　Install Outdoor Unit

☆　Install Connect Pipe

●

　Pipe can be led from 4 directions of right, rear right, left and rear left.

1. When routing pipe (wire) at right side or left side, cut off tailings of pipe left on chassis of main

unit in necessary (as shown in fig. 6).

(1)

Cut off tailing 1 when only power cord is routed;

(2) Cut off tailings 1 and 2 (or 1,2 and 3) when connect pipe and power cord are routed;

2. Pull out pipe from bottom of case, wrap pipes, wires and drainage hose by strap then make

3. Hang the slots behind indoor unit onto the upper tabs of rear panel, then move the unit left
and right to check if it is firm enough (as shown in fig. 8).

4. Ensure the install height of indoor unit is 2m or more.

Gas side pipe

Wire

Liquid side

Heat insulator

Heat insulator

Drainage hose

Wrap by strap

Tailing 1

Tailing 3

Tailing 2

Fixing hook

Install

Install plate

Right

Rear right

Left

Rear left

Fig. 6

Fig. 7

Fig. 8

☆Install Indoor Unit

1. Align the flare of connect pipe to the joint flare of corresponding valve.

2. Tighten nuts on connect pipe and then tighten it by spanner.

1. Take off handle at right side of outdoor unit.

2. Take off clamp, connect and fix the power connect

wire onto line bank. The wire connection should

3. Fix power connect wire by clamp. To cooling and

heating unit, fix signal control wire by clamp, and

then connect to corresponding connector.

4. Ensure wire had been fixed well.

5. Put on handle.

Handle

☆ Wire connection

them though wire hole (as shown in fig. 7).

plate

pipe

in the end

match that of indoor unit.

Blue

Black

Yellow-green

Signal control wire

(Only for cooling and heating unit)

Clamp

Power connect wire

－１７－

into the hole 25 on the chassis as shown in figure.

When heating, condensate produced by outdoor

1. Take off nut cover on cut-off valve of outdoor unit.

2. Align the center of wire, tighten it the flare nut

and nut on freon charging nozzle.

3. Tighten flare nut by spanner.

4. Take off valve cover on liquid valve and gas valve

5. Screw out valve core of liquid valve by hex wrench

and prize the gas core on gas valve by screwdriver.

At this time, some gas may be exhausted.

6. When exhausted for about 15s and refrigerant gas

appear, close gas core, tighten nut on freon charge nozzle.

7. Open valve core of liquid valve and gas valve completely

8. Tighten the valve caps and test leakage at all joints

of the pipe (both indoor and outdoor unit) with liquid

soap or leakage detector.

9. If it is possible, exhaust air in unit by vacuum pump

on gas core (fig. 10).

☆　Drainage of Condensate of Outdoor Unit

unit and defrost water when defrosting could be drained

to proper place by drainage hose.

Install method: Insert the outdoor drainage joint

Then connect the drainage hose to drainage mouth so

that condensate and defrost water could be drained

Screwdriver

Gas pipe

Freon charge

Gas

Liquid

Liquid valve

Hex wrench

Vacuum meter

Valve cap

Thin pipe

Thick pipe

Vacuum pump

Outdoor drainage

Chassis of

enough by hand.

☆　Vacummize and Leakage Detect

Fig. 9

Fig. 10

Fig. 11

(fig. 9)

nozzle

pipe

valve

(Not for cooling only unit)

to proper place.

outdoor unit

joint

－１８－

AUTO/STOP

ON/OFF button

◆　Trial Run and Check Items after Installation

☆　Trial Run

1. Preparation for trial run

(1) Don't turn on power before entire installation

(2)

Ensure the correct connect of control wire, all

wire should be connected firmly.

(3)

Both cut-off valve of thin and thick pipe should

(4) Take off all scattered objects, especially metal scrap, wire waste etc from the unit.

2. Trial run method

(1) Connect power, press ON/OFF on wireless remote control, then unit begins to run.

(2)

Press MODE to select running mode of COOL, HEAT and SWING to see if the running is normal.

(3) Conduct the following operation when emergency run under the circumstance of wire-

(a) Press ON/OFF button when unit is off, then unit be in auto run operation. Micro-computer

would select COOL, HEAT and FAN automatically according to indoor temperature to offer

comfort effect. Repress ON/OFF button to stop the operation.

(b) Press ON/OFF button when unit is on to stop the unit from operating.

☆　Check after Installation

Items to be checked

Is installation firm?

Possible malfunction

Unit may drop, shake or emit noise

Is leakage detect done?

It may lead insufficient of refrigerate capacity

Is heat insulation sufficient?

Condensation or drop may occur

Is drainage smooth?

Condensation or drop may occur

Is power voltage the same with that in

Malfunction or burnout of parts may occur

Malfunction or burnout of parts may occur

Is connection of circuit and pipeline correct?

Is the unit earthed safely?

Creepage may occur

Is model of wire fits that of regulation?

Malfunction or burnout of parts may occur

Insufficient of refrigerant capacity may

Are air intake or outlet vent of indoor and

outdoor unit blocked?

Are length of refrigerant pipe and charge

Charge mount of refrigerant may be hard

are completed.

be opened.

less remote control is missing.

product nameplate?

volume of refrigerant recorded?

to handle.

occur

－１９－

１

３

４

７

８

１０

１２

１３

１９

１７

Usage Notice

１５

Name of Every Part of The Unit

１４

Usage Method of Wireless Remote Control

２０

Users' Notice

Appendix

Maintenance

Troubleshooting

Select of Install Location

Wire Allocation and Earth Requirement

Install Dimension Diagram

Install Indoor Unit

Install Outdoor Unit

Trial Run and Check Item after Installation

Thank you for choosing SINCLAIR Air conditioner, For correct use, please keep
this owner's manual carefully for consultation.

CONTENT

Maintenance

Install Service

Instruction of Health Function

ENVIRONMENTAL INFORMATION

This unit contains fluorinated gases with greenhouse effect covered by the Kyoto Protocol.
Maintenance and disposal must be carried out by qualified persons only.
Refrigerant gas R410A, GWP = 1730

EXTRA REFRIGERANT CHARGE

Pursuant to Regulation EC 842/2006 on certain fluorinated greenhouse gases, in case of extra
refrigerant charge, it is compulsory to:

- Fill in the label accompanying the unit inserting the factory quantity of refrigerant

charge (see the technical label), the extra refrigerant charge and the total charge.

- Apply the label next to the technical label applied on the unit. For the split-type air

conditioner apply on the outdoor unit.