Sinclair ASH-09AISR, ASH-09AISB, ASH-09AISW, ASH-13AISR, ASH-13AISB, ASH-13AISW User Manual

USER'S MANUAL

SYMPHONY SERIES

ASH-09AISR, ASH-09AISB, ASH-09AISW

ASH-13AISR, ASH-13AISB, ASH-13AISW



CONTENTS

Operation and Maintenance

■ ..................................1

Safety Precautions

■ Operation Tips .....................................17

■

Name of Parts

......... ...............................4

■

Operation of Remote Controller

............... ............. 5

■ ...................................11

Care and Cleaning

■ ....................................14

Troubleshooting

Installation Service

■ ................................19

Notices for Installation

■ .................................22

Installation Drawing

■ . .................................23

Installation of Indoor Unit

■

..........................

26

Installation of Outdoor Unit

■ 　 ..．............27

Check after Installation and Operation Test

■ ................................10

Emergency Operation

Do not dispose this product as unsorted municipal waste.

Collection of such waste separately for special treatment

is necessary.

Never attempt.

Be sure to follow this instruction

The physical product may differ from the drawing in this manual for different display.
If there are some differences between them, please refer to the physical product as

the standard

.

This appliance is not intended for use by persons (including children) with reduced

physical, sensory or mental capabilities or lack of experience and knowledge,
unless they have been given supervision or instruction concerning use of the appliance
by a person responsible for their safety.

Children should be supervised to ensure they are away from the appliance.

■ ........28

Installation and Maintenance of Healthy Filter(Optional)

WARNING

Please read the following notices before operation.

★

cut off power

If there's abnormal pheno-

If this abnormal status is kept

★★

★

Safety Precautions

it may

on, air conditioner may be
damaged or

even cause

electric shock or fire.

menon

(like smell of burning),
please cut off the power imm­ediately and then contact with
authorized maintenance
center.

Do not operate the air cond-

itioner with wet hands.

Otherwise, it may cause electric
shock.

Do not cut off or damage the
power cord or signal control
wire. If the power cord or signal
control wire of air conditioner

is damaged,

please replace it by
the professional with specified
power cord.

The special circuit must be
adopted for power supply to
avoid fire.

Do not use octopus multipurpose
socket or mobile wiring board for
wire connection.

Please cut off the power supply

when the air conditioner won't be
used for an extended period of

★

time.

Otherwise, accumulated dust
may cause overheating, fire

and other accidents.

★

Do not damage the power
cord or use unspecified
power cord.

★

Otherwise, it may cause fire due to
overheating of power cord.

★

Before cleaning the air con-

ditioner,

please cut off the power.

★

Otherwise, it will cause electric
shock or injury.

★

Power supply should adopt
the special circuit with the prote­ction of air switch and the capacity

must be sufficient. Pease do not
turn on or turn off the air conditioner

frequently .
Y-type connection is adopted for the
power supply of this air conditioner.
If the power cord is damaged, it

must be replaced by the

manuf-

acture

r, maintenance center or a

similarly qualified person to avoid
a hazard.

★

When the voltage is too high,
electric elements can be damaged

easily;

if the voltage is too low, the
compressor will vibrate fiercely,

which may damage the cooling
system or compressor, and electric
components can't operate.

１

★

★

★

2

★

★

For safety, be sure to turn
off the circuit beaker before

★

★

★

★

No earthing may cause electric

shock.

performing any maintenance

Accumulated dust may cause fire
or electric shock.

Select the most appropriate

temperature.

Keep room about

5 cooler than

outside.

It can save electric energy.

Do not keep windows and

doors open for a long time

during operation.

It will result in insufficient performance.

Do not block the air inlet or
outlet.

and cause

malfunctions.

Keep combustible

materials

at least 1m away

from the

units .

.noisolpxe ro erif esuac yam tI

It may cause falling of the unit

and

injury to the person.

Install the outdoor

unit firmly

enough.

Do not step on the top of the
outdoor unit or place heavy

things on it.

It may cause damage or injury

.

eht riaper ot tpmetta ton oD

air conditioner by yourself.

Incorrect repairs may cause electric
shock or fire.

Please contact the

local a

uthorised s

ervice center.

Always ensure effective

earthing.

or cleaning or when the
product is not used for an
extended period of time.

Safety Precautions

℃

It will result in insufficient performance

3

★

★

★

★

★

★

★

★

Safety Precautions

Do not cut off or damage the power cords or
control cords. If they are damaged, please

contact the dealer or qualified service
personnel

To change the airflow direction, adjust the vertical
and horizontal air flow direction by using the
remote controller.

Vertical

Louver

Horizontal

Louver

Do not insert your hands or objects into
the air in let or outlet.

It may cause an accident.

Do not expose animals or plants directly to
the air flow .

Do not expose yourself to cold air directly
for a long time.

Do not use the unit for any other purpose , such
as preserving food

or drying clothes.

Do not splash water on the air conditioner. Do not place a burner near the air

conditioner .

It will cause CO toxicosis due to incomplete burning.

It may have a detrimental effect on them.

It's not good for your health.

It may cause electric shock or malfunction.

⑹

⑸

⑵

⑻
⑼
⑽

⑷

⑺

⑶

⑴

Power cord

Remote controller

Front panel

Filter

Horizontal louver

Wall pipe

Binding tape

Connection wires

Drain hose

Drain connector

Name of Parts

⑸

⑻

⑶

⑼

⑽

⑴

⑵

Indoor unit

Air in

Air out

Outdoor unit

Air in

Air out

⑷

⑹

⑺

：Cool
：Dry
：Heat

：Set temp.

：

Power

The icons displayed:

4

5

Operation of Remote Controller

T-ON T-OFF

1

7

(not available)

Press it to set HEALTH or AIR function.

8

I FEEL

/

4

3

2

5

6

11

13

12

16

10

14

9

15

Press it to start or stop operation.

ON/OFF

MODE

+

-

Press it to select operation mode
(AUTO/COOL/DRY/FAN/HEAT).

: Press it to increase temperature

setting.

: Pressittodecrease temperature

setting.

FAN

Press it set swing angle.

QUIET

SWING

CLOCK

X-FAN

TEMP

TURBO

SLEEP

LIGHT

Press it to set fan speed.

Press it to set

Press it to set auto-off/auto-ontimer.

Press it set clock.

3

15

5

4

14

7

16

13

12

9

8

11

10

2

1

6

Press it to turn on/off the light.

QUIET function.

6

Operation of Remote Controller

6

Press this button to set up &down swing angle,which circularly changes as below

:

OFF

This remote controller is universal . If any command , or is sent out,

the unit will carry out the command as

indicates the guide louver swings as:

Press this button to turn on I FEEL function. The unit automatically adjust temperature
according to the sensed temperature. Press this button again to cancel I FEEL function.

I FEEL:

SWING:

7

Remote Controller Description

ON/OFF :

MODE :

+ :

AUTO

COOL

DRY

FAN HEAT

*

*Note:Only for models with heating function.

After energization, AUTO mode is defaulted. In AUTO mode, the set temperature will not
be displayed on the LCD, and the unit will automatically select the suitable operation
mode in accordance with the room temperature to make indoor room comfortable.

This button is used for setting Fan Speed in the sequence that goes from AUTO,

to

then back to Auto.

,

, ,

,

FAN

:

1

4

3

2

5

Press this button toturn on the unit .Press this button again to turn off the unit.

Press this button to decrease set temperature. Holding it down above 2 seconds rapidly
decreases set temperature. In AUTO mode, set temperature is not adjustable.

Press this button to increase set temperature.Holding it down above 2 seconds rapidly
increases set temperature. In AUTO mode, set temperature is not adjustable.

Auto

Medium speedLow-Medium speedLow speed

High speedMedium-High speed

Each time you press this button,a mode is selected in a sequence that goes from AUTO,
COOL,DRY, FAN,and HEAT

*

,as the following:

7

Operation of Remote Controller

Remote Controller Description

P

ress this button to achieve the on and off of healthy and scavenging functions in
operation status.Press this button for the first time to start scavenging function;
LCD displays“ ”. Press the button for the

second time to start healthy and scavenging

functions simultaneously; LCD displays“ ” and “ ” .

Press this button for the third

time to

quit healthy and scavenging functions simultaneously. Press the button for the

fourth

time to start healthy function; LCD display “ ”

. Press this button again to repeat

the operation above.

/

8

SLEEP:

9

Press this button, can select Sleep 1 ( ), Sleep 2 ( ),Sleep 3 ( ) and cancel
the Sleep,circulate between these, after electrified, Sleep Cancel is defaulted.

Sleep 1 is Sleep mode 1, in Cool, Dehumidify modes: sleep status after run for one hour, the
main unit setting temperature will increase 1

Sleep 3- the sleep curve setting under Sleep mode by DIY:
(1) Under Sleep 3 mode, press "Turbo" button for a long time, remote control enters into user
individuation sleep setting status, at this time, the time of remote control will dis

play "1hour ",

(2) Adjust "+" and "-" button, could change the corresponding setting temperature, after
adjusted, press "Trubo "button for confirmation;

(3) At this time, 1hour will be automatically increased at the timer postion on the remote

(4) Repeat the above step (2)

～ (3) operation, until 8hours

temperature setting finished,

sleep,curve setting finished, at this time, the remote control will resume the original timer

the setting temperature "88" will display the corresponding temperature of last setting sleep
curve and blink (The first entering will display according to the initial curve setting value of

original factory);

control, (that are "2hours " or "3hours " or "8hours "), the place of setting temperature "88"
will display the corresponding temperature of last setting sleep curve and blink;

display;temperature display will resume to original setting temperature.

●

●

Sleep3- the sleep curve setting under Sleep mode by DIY could be inquired:
The user could accord to sleep curve setting

method to inquire the presetting sleep curve,

enter into user

individuation sleep setting status, but do not change the temperature, press

"Turbo" button directly for confirmation.

Note: In the above presetting or enquir

y procedure,
if continuously within10s, there is no button pressed, the sleep curve setting within
10s, there is no button pressed, the sleep curve setting status will be automatically
quit and resume to display the original displaying. In the presetting or enquiry procedure, press

●

●

℃,setting temperature increased 2℃, the unit will
run at this setting temperature; In Heat mode: sleep status after run for one hour, the setting
temperature will decrease 1

℃, 2 hours, setting temperature will decrease 2

℃, then the unit

will run at this setting temperature.

●

Sleep 2 is sleep mode 2, that is air conditioner will run according to the presetting a group of
sleep temperature curve.

"ON/OFF" button, "Mode" button, "Timer"button or "Sleep" button, the sleep curve setting
or enquiry status will quit similarly.

8

Operation of Remote Controller

LIGHT:

15

Press LIGHT button to turn on the display's light and press this button again to turn off

the display's light. If the light is turned on , is displayed. If the light is turned off,

disappears.

TURBO:

14

Press this button to activate / deactivate the Turbo function which enables the unit to

reach the preset temperature in the shortest time. In COOL mode, the unit will blow strong

cooling air at super high fan speed. In HEAT mode, the unit will blow strong heating air

at super high fan speed.

Press this button, could select displaying the indoor setting temperature or indoor ambient
temperature.When the indoor unit firstly power on it will display the setting temperature,
if the temperature's displaying status is changed from other status to" ",displays the
ambient temperature, 5s later or within 5s, it receives other remote control signal that will

return to display the setting temperature. if the users haven't set up the temperature
displaying status,that will display the setting temperature.

T-ON T-OFF:

present time.Holding down either button above 2 seconds increases or decreases the

CLOCK :

time by 1 minute every 0.5 second and then by 10 minutes every 0.5 second. During
blinking after setting, press CLOCK button again to confirm the setting,and then

10

TEMP:

Press T-ON button to initiate the auto-ON timer. To cancel the auto-timer program, simply

press this button again.

After press of this button, disappears and "ON "blinks .0

0:00 is displayed for ON time

setting. Within 5 seconds, press + or - button to adjust the time value. Every press of either

button

changes the time setting by 1 minute. Holding down either button rapidly changes the

time settingby1 minuteand then10 minutes. Within 5Seconds aftersetting, pressTIMER

ON button to confirm.

12

will

be constantly displayed.

QUIET:

11

13

Press T-OFF button to initiate the auto-off timer. To cancel the auto-timer program, simply
press the button again.TIMER OFF setting is the same as TIMER ON.

Press this button, the Quiet status is under the Auto Quiet mode (display "

Auto

"signal )
and Quiet mode (display " " singal) and Quiet OFF (there is no signal of " "
displayed),after powered on, the Quiet OFF is defaulted.

Press CLOCK button, blinking . Within 5 seconds,pressing +or - button adjusts the

X-FAN:

16

Pressing X-FAN button in COOL or DRY mode, the icon is displayed and the indoor
fan will continue operation for 10 minutes in order to dry the indoor unit even though you

have turned off the unit.
After energization, X-FAN OFF is defaulted. X-FAN is not available in AUTO, FAN or
HEAT mode.

9

Operation of Remote Controller

★

●

●

●

●

●

1.Remove the battery cover plate from the rear of the remote controller.
(As shown in the figure)

2.Take out the old batteries.

3.Insert two new AAA1.5V dry batteries, and pay attention to the polarity.

4. Reinstall the battery cover plate.

When replacing the batteries, do not use old or different types of batteries,

If the remote controller will not be used for a long time, please

otherwise, it may cause malfunction.

remove batteries to prevent batteries from leaking.
The operation should be performed in its receiving range.
It should be kept 1m away from the TV set or stereo sound sets.
If the remote controller does not operate normally, please take the

batteries out and reinsert them after 30 seconds.If it still can't

operate properly,

Notes:

replace the batteries.

Sketch map for
replacing batteries

Replacement of Batteries

Press "+ " and "-" buttons simultaneously

to lock or unlock the keypad. If the remote

controller is locked, is

displayed. In this case,

pressing any button, blinks

three times.

At unit OFF, press "MODE"

and " - " buttons simultaneously to switch between and .

℃

℉

Combination of "+" and "-" buttons: About lock

17

About Back-lighting Function

21

Combination of "MODE " and "-" buttons :

18

About switch between Fahrenheit and centigrade

Press “TEMP” and “CLOCK” simultaneously in COOL mode to start energy-saving function.
Nixie tube on the remote controller displays “SE”. Repeat the operation to quit the function.

Combination of " TEMP " and "CLOCK" buttons : About Energy-saving Function

19

Press “TEMP” and “CLOCK” simultaneously in HEAT mode to start

The unit lights for 4s when energizing for the first time, and 3s for later press.

8℃ Heating Function

.

Nixie tube on the remote controller displays “ ” and a selected temperature of “

8℃”

(46 if Fahrenheit is adopted). Repeat the operation to quit the function.

Combination of " TEMP " and "CLOCK" buttons : About 8℃ Heating Function

20

℉

Mode Model Temperature setting Airflow rate
AUTO COOLING 25 (COOL,FAN) AUTO
AUTO HEAT

℃
℃
℃

PUMP 25 ( COOL,FAN) AUTO

AUTO HEAT PUMP 20 ( HEAT) AUTO

10

Emergency Operation

When the remote controller is lost
or damaged, please use the manual switch
on the main unit. In that case, the unit will
operate in AUTO mode and the temperature
setting or fan speed can not be changed.

The manual switch can be operated as below:

Turn on the unit: Press AUTO/STOP button to
enter AUTO mode.
The microprocessor will select the mode
(COOL, HEAT, FAN) automatically according

to the room temperature for reaching comfortable

effect.

Turn off the unit: Press the AUTO/STOP button to
switch off the unit.

Emergency Operation

●

●

Manual switch

The operation mode is shown in the following table.

●

This switch is to be applied when the remote controller is missing.

●

℃

?

?

(Fig.a)

(Fig.b)

Caution

Wipe the units with a dry soft cloth, or a cloth slightly moistened with water or cleaner (not with
volatile liquid such as thinner or gasoline).

Note: If the air conditioner operates under dusty environment, the frequency of cleaning air filter shall
increase correspondingly. When the filter is removed, do not touch the fins of the indoor unit with fingers
for fear of scalding.

Remove the front panel.

●

●

●

Disconnect the power supply before cleaning and maintenance.

Do not splash water on the units for cleaning, as electric shocks may occur.

Dip a piece of cloth into the water colder than 45 and dry it . Then wipe

the dirty part of front panel.
Note: Do not immerse the front panel into water so as to protect microprocessor components and circuit

diagram on the front panel.

Care and Cleaning

11

℃

② Clean the air filter

③

①

Take down the air filter

Press the clasp as shown by arrow (1) to loosen the
lower end of clasps until a sound of “crack” is heard;
press the clasp as shown by arrow（2）to open the
upper end of clasp; open the panel and then pull the
filter downward to remove it.(As shown in figa and b)

Clean the filter with a vacuum cleaner or wash the filter
with water. If the filter is very dirty (such as oil stain),
please clean it with the mixture of warm water (<45℃)
and neutral abluent and then dry it up in the shade.

Note: Never use water above 45 to clean the air
filter as it may cause deformation or discoloration.

Reinstall the air filter

Install the air filter along arrow (1) direction and then
buckle the panel cover along arrow (2).

Cleaning the Air Filter (every 3 months)

Cleaning the Front Panel

⑴

⑵

⑵

⑴

⑵

12

1. Press the clasp as shown by arrow (1) to loosen
the clasps at the lower end until a sound of “crack” is
heard; press the clasp as shown by arrow （2） to open
the clasps at the upper end; open the panel and then
pull the filter downward to remove it.
(As shown in fig a)

2. Install the healthy filter on the air filter (as shown in
fig b). If the healthy filter fails to be installed on the
air filter, please install the healthy filter on the
front case（As shown in fig c）.

3. Install the air filter along arrow (1) direction and
then buckle the panel cover along arrow (2).
　（As shown in fig d）

Please remove the healthy filter before cleaning and reinstall it well after cleaning
according to the installation instruction. Please note that the silver ion filter shall
NOT be washed by water. Active carbon filter, photocatalytic filter，LTC catalyst
and formaldehyde-killer filter can be washed by water, but shall not be scrubbed
with a brush or hard object. When washing is completed, dry the filter in shade rather
than wipe with a rag.

Installation and Maintenance for Healthy filter

Clean and Maintenance for Healthy Filter

The general service life for healthy filter is one year under normal operation. As to
silver ion filter, it is ineffective when the surface turns black（or green）.

● This complementary instruction is only referred for the unit with healthy filter.The

graphs in this complementary instruction may be different from the actual product,
please refer to the actual product. Please refer to the actual delivery for the quantity of
healthy filter.

Service Life for Healthy Filter

Fig a.

Fig d.

Fig c.

Fig b.

Care and Cleaning

Healthy filter

Healthy filter Install position

Air filter

⑴

⑵

⑵

⑴

⑵

13

① Make sure that nothing obstructs the air inlet and air

outlet of indoor and outdoor units.

②

③

①
②

③

④

④

Check before Use

Maintenance after Use

Disconnect the power for the air conditioner.
Clean the filter and the body of indoor and outdoor units.

Remove the dust and other objects on the outdoor unit.

Make sure the installation support for outdoor unit is in good condition.
If it’s damaged, please contact appointed maintenance center.
If there is rust on the outdoor unit, please apply some paint to the rusty
spot to avoid spreading. BE CAREFUL when painting.

⑤

Indoor and outdoor units can be wrapped by special protective bags to avoid rain
and dust getting into the units to erode them.

Make sure there is effective grounding.

Make sure the batteries for remote controller are replaced.

Make sure the installation support for outdoor unit is in good condition. If it’s damaged,
please contact

appointed maintenance center. If there is rust on the outdoor
unit, please apply some paint to the rusty spot to avoid spreading. BE CAREFUL
when painting!

Care and Cleaning

●

●

●

●

●

●

Troubleshooting

CAUTION

Phenomenon

Troubleshooting

Waiting

The unit does not operate:

The unit does not operate if it is turned on
immediately after being turned off. This is to

Odours are emitted:

Some odours may be emitted from the indoor
unit. This is the result of room smells (such as
furniture, tobacco, ect.) which have been taken

Consult authorized service center for cleaning
if the odours still exist.

"Water flowing" noise:

The swishing noise like water flowing is the

sound of refrigerant flowing inside the unit.

Mist is emitted in COOL mode

During cooling operation, a thin mist may be

seen emitted from the indoor unit due to high

room temperature and humidity.

After a period of time,

the mist will disappear with the decrease of

room temperature and humidity.

14

The air conditioner is not expected to be serviced by users. Incorrect repair may cause
electric shock or fire, so please contact an authorized service center for professional
service. The following checks prior to contact may save your time and money.

Cracking noise:

This is the sound of friction caused by expansion

and/or contraction of panel or other parts due

to the change of temperature.

protect the unit. You are expected to

wait

for

about 3

minutes.

into the air conditioner.

●

●

●

●

●

●

●

●

●

●

●

●

●

●

●

●

●

●

●

●

●

Troubleshooting

Phenomenon

Troubleshooting

The unit can not be started up:

Is the power cut off?
Is the power plug loose? (If applicable)
Is the circuit protection device tripped off?
Is voltage higher or lower?

(Tested by professionals)

Is the TIMER correctly used?

Cooling/Heating effect is poor:

Is temperature setting appropriate?

Is
Is

filter dirty?

Is low fan speed set?

Remote controller is not available:

The humidity is high.

Condensate

Drain hose is loose.

Noise from indoor unit. The noise emitted when the fan or compressor

relay is switching on or off.

Breaking off

inlet or outlet blocked?

Are there heat sources in the room?

the

the

Check if there is magnetic or electrical interference
near the unit that may affecting operation of
the controller. In this case, pull the plug out and
reinsert it.

Is the remote controller within its operating range
or obstructed? Check the condition of the
batteries and replace them if necessary.

Check if the remote controller is damaged.

Water leakage of indoor unit :

Water leakage of outdoor unit :

overflows.

During cooling operation, condensate is

generated around the pipes and connection joints.

During defrosting operation, the thaw water flows
out.

●　

During heating operation, the water on the heat

exchanger drips out.

When the defrosting operation is

started or stopped,
there is a sound of refrigerant flowing in the
reverse direction.

Is the window or the door open?

15

16

In HEAT mode, when the temperature of indoor

heat exchanger is very low, air flow is stopped
in order to prevent cold air. (Within 2 minutes)

In HEAT mode, when the outdoor temperature
is low or humidity is high, frost will be formed on
the outdoor heat exchanger. The unit will defrost

automatically and indoor unit will stop blowing
air for 3-12 minutes.

During defrosting operation, water or vapour may
be emitted.

●

In DRY mode, the indoor fan will stop blowing air

for 3-12 minutes in order to avoid condensate

being vaporised again.

If the unit operates at high humidity for a
long time, moisture will be generated on
the air outlet grill and then drip off.

If any one of the following situations occurs, immediately stop all operations,

cut off the power supply, and contact the authorized personnel

Strong odours are emitted during operation.

The air switch or protection switch often trips.

Power cord and power plug is overheating.

noitarepo potS

and cut off the power supply.

●

●

●

●

Troubleshooting

Phenomenon

Troubleshooting

Indoor unit can not blow air:

Moisture on air outlet :

C5: Malfunction of connector jumper: Check if the connector jumper contacts

properly. If the PCB is to be replaced,
please take off the old for the new PCB.

●

F1

: Malfunction of indoor ambient temperature

sensor

sensor

Check if indoor room temperature sensor is
connected properly．

●

F2: Malfunction of evaporator temperature Check if the evaporator temperature is

connected properly.

There is harsh sound during operation.

Water is leaking from the unit.

Water or other liquid is splashed into the unit.

Operation Tips

Cooling Operation

17

Principle:

Air conditioners absorb heat in the room and transmit it to the outdoor unit so that the
room temperature is decreased. The cooling capacity will increase or decrease according
to outdoor ambient temperature.

F

reeze

Protection:

If the unit is operating in COOL mode and in low ambient temperature, frost may form

on the heat exchanger. When indoor heat exchanger temperature decreases below zero,

compressor will stop operation to protect the unit.

*

*

*

*

*

Principle:

Defrosting:

Air conditioners absorb heat from outdoors and transmit it to the indoor unit, increasing
room temperature. The heating capacity will decrease at low ambient temperature.

When outdoor temperature is low but humidity is high, frost may form on the outdoor unit
during extended operation, affecting heating efficiency. The air conditioner may stop
operation during auto defrosting operation.

During auto defrosting, the fan motors of indoor unit and outdoor unit will stop.

During defrosting, the indoor indicator displays “ ” and the outdoor unit may emit vapor.
This is not malfunction.

After defrosting is finished, the heating operation will recover automatically.

C

old Blow Prevention:

In HEAT mode, the indoor fan will not operate in order to prevent cold air blowing out

(within 2 minutes) if indoor heat exchanger doesn't reach a certain temperature under the
following three states:

1. Heating operation starts; 2. After Auto Defrosting is finished; 3.Heating at low temperature.

Gentle Breeze

In the following situations, the indoor unit may blow gentle breeze, and the horizontal
louver rotates to a certain position:

1. In HEAT mode, the compressor does not start operation after the unit is turned on.

2. In HEAT mode, the temperature reaches the set value and the compressor has stopped

operation for about 1minutes.

Heating Operation

18

Operation Tips

Tips for energy saving:

* Do not overcool or overheat

.

Setting temperature at a moderate level helps energy saving.

*

Cover windows with a blind or a curtain.

Blocking sunlight and air from outdoors is favorable for cooling (heating).

*

Clean air filters once per two weeks.

Clogged air filters lead to inefficient operation and energy waste.

The operating temperature range (outdoor temperature) for cooling only unit is 18℃

~

43℃；

for heat pump unit is -7℃

~

24℃.

Operating Temperature Range

Maximum cooling

Minimum cooling

Maximum heating

Minimum heating

Indoor side DB/WB(oC)

Outdoor side DB/WB(oC)

32/23
21/15

27/--­20/---

43/26
21/15

24/18

-

7/-8

Tip for relative humidity:

Condensate is likely to form at the air outlet if cooling or drying for a long time

when the relative humidity is more than 80% ( with doors and windows open).



4

.

Warning: Before obtaining access to terminals, all supply circuits must be disconnected.

5.

For appliances with type Y attachment, the instructions shall contain the substance of
the following. If the supply cord is damaged, it must be replaced by the manufacturer, its

service agent or similarly qualified persons in order to avoid a hazard.

6.The appliance must be positioned so that the plug is accessible.

7.The temperature of refrigerant line will be high; please keep the interconnection cable
away from the copper tube.

8. The instructions shall state the substance of the following:
This appliance is not intended for use by persons(including children)with reduced physical,

sensory or mental capabilities, or lack of experience and knowledge, unless they have been

given supervision or instruction concerning use of the appliance by a person responsible
for their safety.

Children should be supervised to ensure that they do not play with the appliance.

Notices for Installation

Caution

Installation Site Instructions

19

The unit should be installed only by authorized service center according to local or

government regulations and in compliance with this manual.

Before installing, please contact with local authorized maintenance center. If the unit is

not installed by the authorized service center, the malfunction may not be solved

due to incovenient contact between the user and the service personnel.

When removing the unit to the other place, please firstly contact with the local authorized

service center.

●

●

●

●

●

●

Proper installation site is vital for correct and efficient operation of the unit. Avoid the
following sites where:

strong heat sources, vapours, flammable gas or volatile liquids are emitted.

high-frequency electro-magnetic waves are generated by radio equipment,
welders and medical equipment.
salt-laden air prevails (such as close to coastal areas).
the air is contaminated with industrial vapours and oils.

the air contains sulphures gas such as in hot spring zones.

corrosion or poor air quality exists.

1

.

2.

3.

Note:

Notices for Installation

Safety Precautions for Electric Appliances

Installation Site of Outdoor Unit

20

1

.

Select a site where noise and outflow air emitted by the unit will not annoy neighbors.

Select a site where there is sufficient ventilation.
Select a site where there is no obstruction blocking the inlet and outlet.
The site should be able to withstand the full weight and vibration.
Select a dry place, but do not expose the unit to direct sunlight or strong wind.
Make sure that the outdoor unit is installed in accordance with the installation instructions,

and is convenient for maintenance and repair.
The height difference between indoor and outdoor units is within 5 m, and the length of

the connecting tubing does not exceed 10 m.

Select a place where it is out of reach of children.

Select a place where the unit does not have negative impact on pedestrians or on the city.

5. The minimum distance between the unit and combustive surface is 1.5m.

1. A dedicated power supply circuit should be used in accordance with local electrical

safety regulations.

2. Don't drag the power cord with excessive force.

3.

The appliance shall be installed in accordance with national wiring regulations.

An all-pole disconnection switch with a contact separation of at least 3mm in all poles
should be connected in fixed wiring.

The unit should be reliably earthed and connected to an exclusive earth device by the

professionals.

4. The air switch must have the functions of magnetic tripping and heat tripping to prevent
short circuit and overload.

Make sure the live wire, neutral wire and earth wire in the family power socket are properly
connected. There should be reliable circuit in the diagram.

Inadequate or incorrect electrical connections may cause electric shock or fire.

●

●

6.

7.

2.

3.

4.

5.

6.

7.

8.

9.

Installation Site of Indoor Unit

Select a site where the condensate can be easily drained out, and where it is
easily connected to outdoor unit.

Select a place where the wall is strong enough to withstand the full weight and vibration
of the unit.

Make sure that the indoor unit is installed in accordance with installation dimension

Select a place where it is out of reach of children.

The air inlet and outlet should be away from the obstructions. Ensure the air can be

blown through the whole room.

Be sure to leave enough space to allow access for routine maintenance. The installation
site should be 250cm or more above the floor.

Select a place about 1m or more away from TV set or any other electric appliance.

Select a place where the filter can be easily taken out.

instructions.

6.

7.

8.

5.

4.

1

.

2.

3.

9. Do not use the unit in the laundry or by swimming pool etc.

Earthing Requirements

① ②

③

④

1. Air conditioner is type I electric appliance. Please ensure that the unit is reliably earthed.

2. The yellow-green wire in air conditioner is the earthing wire which can not be used
for other purposes. Improper earthing may cause electric shock.

3. The earth resistance should accord to the national criterion.

4. The power must have reliable earthing terminal. Please do not connect the earthing

wire with the following:

W epipsaGepipreta

Contamination pipe

Other place that professional personnel consider is unreliable

5. The model and rat

6. Including an air switch with suitable capacity, please note the following table. Air switch

ed values of fuses should accord with the silk print on fuse cover or

related

should be included magnet buckle and heating buckle function, it can protect the
circuit-short and overload. (Caution: please do not use the fuse only for protect the circuit)

PCB.

Notices for Installation

21

09K

12K 16A

25A 18K

16A

Air switch capacityAir-conditioner (W)

Space to the wall

Above

Above

Installation Drawing

Installation Drawing

Space to the ceiling

Space to the wall

Space to the wall

Air outlet side

Space to the floor

Above

Above

Above

Above

Above

Space to the obstruction

Air outlet side

Space to the wall

Air inlet side

Above

Above

Above

22

The dimensions of the space necessary for proper
installation of the unit include the minimum
permissible distances to adjacent parts.

●

Ø

55

Drill Piping Hole

1.Slant the piping hole ( 55) on the wall slightly downward to the
outdoor side.

2.Insert the piping-hole sleeve into the hole to prevent the connection piping
and wiring from being damaged when passing through the hole.

Indoor

Outdoor

Wall pipe

Seal pad

23

Installation of Indoor Unit

drain hose

outlet pipe of

indoor unit

outlet pipe of

indoor unit

rubber belt

Installation of Mounting Plate

1. Mounting plate should be installed horizontally. As the water tray's outlet for the indoor unit is two-way
type, during installation, the indoor unit should slightly slant to water tray's outlet for smooth drainage of

condensate.

2.Fix the mounting plate on the wall with screws.

3.Be sure that the mounting plate has been fixed firmly enough to withstand about 60 kg. Meanwhile, the
weight should be evenly shared by each screw.

1.

2.

3.

Installation of Drain Hose

Connect the drain hose to the outlet pipe of the indoor unit.

Bind the joint with rubber belt.

Put the drain hose into insulating tube.

Wrap the insulating tube with wide rubber belt to prevent
the shift of insulating tube. Slant the drain hose downward

slightly for smooth drainage of condensate.

Note: The insulating tube should be connected reliably with

the sleeve outside the outlet pipe. The drain hose should be

slanted downward slightly, without distortion, bulge or
fluctuation. Do not put the outlet in the water.

bulge

distortion

outlet pipe of
indoor unit

insulating tube

connected

insulating tube

drain hose

outlet pipe of

indoor unit

rubber belt

rubber belt

Flooded

Ф

Ø55

845

275

542131

256.8

124

50

Ø55

50

100

Fig.5

18K UNIT:

09、12K UNIT:

275+0.5

-

55

99

575

9.5

55

99

685

189

1018

315

Ø55

45

Ø55

65

09K,

1

2K，

yellow-

green

3

brown

●

●

●

After tightening the screws, pull the wire slightly to confirm whether it's firm or not.

●

●

Make sure that all wiring connections are secure and the cover plates are reinstalled

NOTE:

All wires between indoor and outdoor units must be connected by the qualified electric

contractor.

Electric wires must be connected correctly. Improper connection may cause malfunction.

Tighten the terminal screws securely.

Make sure that the electric connections are earthed properly to prevent electric shock.

properly. Poor installation may cause fire or electric shock.

Connecting Indoor and Outdoor Electric Wires

Fig.6

1.Open the front panel.

2.Remove the wiring cover as shown in Fig 6.

3.Make the power connection cord pass through the hole at the back of indoor unit.

4.Reinstall the cord anchorage and wiring cover.

5.Reinstallthefrontpanel.

24

Installation of Indoor Unit

18K

25

Installation of Indoor Unit

4.

2.

3.

●

1.

⑴
⑵

1.

2.

Installation of Indoor Unit

The piping can be output from right, right rear, left

or left rear.

When routing the piping and wiring from the left
or right side of indoor unit, cut off the tailings
from the chassis when necessary(As shown in Fig.7)

Cut off tailing 1 when routing the wiring only;

Cut off tailing 1 and tailing 2 when routing

both the wiring and piping.
Take out the piping from body case; wrap the piping,
power cords, drain hose with the tape and then make
them pass through the piping hole. (As shown in Fig.8)

Hang the mounting slots of the indoor unit on the
upper hooks of the mounting plate and check if it is

firm enough. (As shown in Fig.9)

The installation site should be 250cm or more above

the floor.

Installation of Connection Pipe

Align the center of the pipe flare with the related valve.

Screw in the flare nut by hand and then tighten the

nut with spanner and torque wrench by referring to the
following:

NOTE: Connect the connection pipe to indoor unit

For 09、12K UNIT:
NOTE: Three situations (in front of the unit)

1. Connecting left water outlet of the unit, drain pipe is laid on the left of the unit.

2. Connecting to left or right water outlet, drain pipe is laid on the right of the unit.

3. Connecting right water outlet of the unit, drain pipe goes through hole in the
wall behind the indoor unit.

at first and then to outdoor unit. Handle pi-

ping bending with care. Do not damage the connection

pipe. Ensure that the joint nut

is tightened firmly, otherwise, it may cause leakage.

Spanner

Torque
wrench

Piping

Taper nut

Indoor unit piping

Fig.9

Mounting
plate

Fixing hook

Mounting
plate

Right

Right rear

Fig.8

Left rear

Left

Fig.7

Tailing 1

Tailing 2

Finally wrap it
with tape

Gas side piping

insulation

Water drainage pipe

Liquid side

Piping insulation

Gas side piping

External connection

electric wire
Liquid side piping

(N·m)

Ф6

Ф 9.52

Ф 12

30～40

15～20

45～55

Ф 16 60～65
Ф 19 70～75

Hex nut diameter

Tightening torque

Manifold
Valve

Multimeter

-76cmHg

LoHandle

Charginghose

Manometer

Hihandle

Charginghose

Vacuumpump

Lo

wpressurevalve

Ø

、0912K 18K

N(1)

Indoor unit
connection

blueblack

brown

yellow-green

2

3

Handle

26

3.

4.

5.

1.

2.

Remove the handle on the right side plate of outdoor unit.

Take off wire cord anchorage. Connect andfix power connection cord
to the terminal board. Wiring should fit that of indoor unit.

Fix the power connection cord
with wire clamps and then connect the
corresponding connector.

Confirm if the wire has been fixed properly.
Reinstall the handle.

AirPurging and LeakageTest

Outdoor Condensate Drainage (only for Heat pump unit)

During heating operation, the condensate anddefrosting
watershould be drained out reliably through the drain hose.

Install the outdoor drain connector in anoeloh42
the base plate and attachthe drain hose to the connector
sothat the waste water formed in the outdoor unit can be
drained out .The hole diameter 42 must be plugged.

●

●

Installation of Outdoor Unit

Electric Wiring

NOTE:

Incorrect wiring may cause malfunction of spare part.

After the wire has been fixed, ensure there is free
space between the connection and fixing places
on the lead wire.

5

-1.0 10 pa

(-76cmHg

)..

1. Connect charging hose of manifold valve to charge end of low pressure
valve (both high/low pressure valves must be tightly shut).

2. Connect joint of charging hose to vacuum pump.

3. Fully open the handle of Lo manifold valve.

4. Open the vacuum pump for vacuumization. At the beginning, slightly

loosen joint nut of low pressure valve to check if there
is air coming inside (If noise of vacuum pump has
been changed, the reading of multimeter is 0). Then
tighten the nut.

5. Keep vacuuming for more than 15mins and make
sure the reading of multi-meter is

6. Fully open high/low pressure valves.

7. Remove charging hose from charging end of low pressure valve.

8. Tighten lid of low pressure valve. (As shown in Fig.10)

Fig.10

S

chematic diagram being reference only, please refer to

Whether to plug other holes will be determined by the dealers according to actual conditions.

Drain-water hole

Bottom frame

Drain plug

Hose (available commercially,
inner dia. 16mm)

Drain connecter

real product for authentic information.

1.
(1)

Do not switch on power before installation is finished completely.

(2)Electric wiring must be connected correctly and securely.
(3)Cut-off valves of the connection pipes should be opened.
(4)

2.

(1)

Switch on power and press "ON/OFF" button on the remote controller to start
operation.

(2)

Check after Installation and Operation Test

Check after Installation

Items to be checked Possible malfunction

Has the unit been fixed firmly?

The unit may drop, shake or emit noise.

Have you done the refrigerant leakage test?

It may cause insufficient cooling(heating)

Is thermal insulation sufficient?

It may cause condensation.

Is water drainage satisfactory?

It may cause water leakage.

Is the voltage in accordance with the rated
voltage marked on the nameplate?

It may cause electric malfunction
or damage the unit.

Is the electric wiring or piping
connection installed correctly and securely?

It may cause electric malfunction
or damage the parts.

Has the unit been securely earthed?

It may cause electrical leakage.

Is the power cord specified?

It may cause electric malfunction
or damage the parts.

Is the inlet or outlet blocked? It may cause insufficient cooling(heating)

Is the length of connection pipes
and refrigerant capacity recorded?

The refrigerant capacity is not accurate.

Operation Test

Before Operation Test

All the impurities such as scraps and thrums must be cleared from the unit.

Operation Test Method

Press MODE button to select the COOL, HEAT (Not available for cooling only unit),

FAN to check whether the operation is normal or not.

27

Installation and Maintenance of Healthy Filter(Optional)

28

Fig. a

1.

2.
(as shown in Fig.b).

3. Install the air filter properly along the arrow

direction in Fig.c, and then close the panel .

Cleaning and Maintenance

Service Life

●

filter

Air filter

(as shown in Fig.a)

Fig. b

Fig. c

Lift up the front panel from its two ends,
as shown by the arrow direction, and

then remove

the air filter.

Attach the healthy filter onto the air filter,
.

Healthy

Remove the healthy filter and reinstall it after cleaning according
to the installation instruction. Do not use brush or hard objects to clean

the filter. After cleaning, be sure to dry it in the shade.

The general service life for the healthy filter is about one year under

normal condition. As for silver ion filter, it is ineffective when its surface

becomes black (green).

This supplementary instruction is provided for reference to the unit with
healthy filter. If the graphics provided herein are different from the actual
product, please refer to the actual product. The quantity of healthy filters
is based on the actual delivery.

Installation of Healthy Filter

ASH‐09AISR ASH‐13AISR
ASH‐09AISB ASH‐13AISB

ASH‐09AISW ASH‐13AISW

cooling kW 2,6(1,0‐3,4) 3,5(1,3‐4,0)

heating kW 2,9(0,6‐3,8) 3,8(0,9‐4,3)

50 50

220‐240 220‐240

cooling A 2,8 4,2

heating A 3,1 4,6

cooling W 645(200‐1200) 970(360‐1300)

heating W 695(160‐1250) 1055(340‐1360)
EER 4,0(2,7‐4,6) 3,6(2,5‐4,4)
COP 4,1(2,4‐4,2) 3,6(2,1‐3,7)
Noise‐indoorunit 22‐38 23‐39
Noise‐outdoorunit max dB(A) 50 52

Airflow 560 560
Dehumidifyingvolume 0,8 1,4
Refrigeranttype/charge R410a/0,9 R410a/1,3

Liquidside inch/mm ¼/6¼

/6

gasside inch/mm ⅜/10 ½/12
Lengthofconnectionpipe max m 15 20
Elevation/Dropheight max m 10 10

IU mm 896x320x159 896x320x159

OU mm 776x540x320 848x540x320

IU kg 11,5 11,5

OU kg 29 38

cooling °C

18~43 18~43

heating °C

‐

7~24 ‐7~24

Dataarebasedonfollowingconditions:
Lengthofconnectionpipe:5m
Cooling:indoortemperature27°CDB/19°CWB,outdoortemperature35°CDB/24°CWB
Heatingcondition:indoor

temperature20°CDB/15°CWB,outdoortemperature7°CDB/6°CWB

Thespecificationofproductsissubjecttochangebasedfurtherdevelopmentoftheunitsbythe

producerandcanbechangedwithoutpriornotice.

Operatingtemperaturerange

Netweight

Dimension(wxhxd)

Pipediameter

type/kg

l/h

m

3

/h

dB(A)

W/W

W/W

Powerinput

Powercurrent

V

Powersupply

Hz

Capacity

MODEL

SERIES SYMPHONY

Model

SPLIT AIR CONDITIONER

INDOOR UNIT

Rated Voltage

220-240V~
Rated Frequency 50Hz
Cooling Capacity 2600W
Heating Capacity 2870W
Air Flow Volume

3

560m /h
Sound Pressure Level(H) 34dB(A)
Weight

11.5kg

Manufactured Date

63229936470

Sinclair Corporation Ltd, 1-4 Argyll St., London, UK

ISO9001

TUV

ASH-09AISW

ISO9001

TUV

AIR CONDITIONER OUTDOOR UNIT

63229936471

Sinclair Corporation Ltd, 1-4 Argyll St., London, UK

Model

Rated Voltage

220-240V~

(ISO 5151)

2600W

Rated Frequency

50Hz

Cooling Capacity

2870W

Climate Type

T1

Heating Capacity

645W

Weight

29kg

Cooling Power Input

695W

Isolation

I

Heating Power Input

Refrigerant

R410A

Cooling Rated Input

1400W

Refri. Charge

0.85kg

Heating Rated Input

1450W

Comp. LRA

25A

Sound Pressure Level

50dB(A)

2.8/1.2MPa

3.8MPa

Manufactured Date

Moisture Protection

I P24

Operating Pressure ( Discharge Si de/Suction Si de)

Maximum Allowable Pressure

Contains fluorinated greenhouse gases covere d by the Kyoto Protocol

ASH-09AISW

Model

SPLIT AIR CONDITIONER

INDOOR UNIT

Rated Voltage

220-240V~
Rated Frequency 50Hz
Cooling Capacity 2600W
Heating Capacity 2870W
Air Flow Volume

3

560m /h
Sound Pressure Level(H) 34dB(A)
Weight

11.5kg

Manufactured Date

63229936468

Sinclair Corporation Ltd, 1-4 Argyll St., London, UK

ISO9001

TUV

ASH-09AISB

ISO9001

TUV

AIR CONDITIONER OUTDOOR UNIT

63229936469

Sinclair Corporation Ltd, 1-4 Argyll St., London, UK

Model

Rated Voltage

220-240V~

(ISO 5151)

2600W

Rated Frequency

50Hz

Cooling Capacity

2870W

Climate Type

T1

Heating Capacity

645W

Weight

29kg

Cooling Power Input

695W

Isolation

I

Heating Power Input

Refrigerant

R410A

Cooling Rated Input

1400W

Refri. Charge

0.85kg

Heating Rated Input

1450W

Comp. LRA

25A

Sound Pressure Level

50dB(A)

2.8/1.2MPa

3.8MPa

Manufactured Date

Moisture Protection

I P24

Operating Pressure ( Discharge Si de/Suction Si de)

Maximum Allowable Pressure

Contains fluorinated greenhouse gases covere d by the Kyoto Protocol

ASH-09AISB

Model

SPLIT AIR CONDITIONER

INDOOR UNIT

Rated Voltage

220-240V~
Rated Frequency 50Hz
Cooling Capacity 2600W
Heating Capacity 2870W
Air Flow Volume

3

560m /h
Sound Pressure Level(H) 34dB(A)
Weight

11.5kg

Manufactured Date

63229936466

Sinclair Corporation Ltd, 1-4 Argyll St., London, UK

ISO9001

TUV

ASH-09AISR

ISO9001

TUV

AIR CONDITIONER OUTDOOR UNIT

63229936467

Sinclair Corporation Ltd, 1-4 Argyll St., London, UK

Model

Rated Voltage

220-240V~

(ISO 5151)

2600W

Rated Frequency

50Hz

Cooling Capacity

2870W

Climate Type

T1

Heating Capacity

645W

Weight

29kg

Cooling Power Input

695W

Isolation

I

Heating Power Input

Refrigerant

R410A

Cooling Rated Input

1400W

Refri. Charge

0.85kg

Heating Rated Input

1450W

Comp. LRA

25A

Sound Pressure Level

50dB(A)

2.8/1.2MPa

3.8MPa

Manufactured Date

Moisture Protection

I P24

Operating Pressure ( Discharge Side/Suction Side)

Maximum Allowable Pressure

Contains fluorinated greenhouse gases covere d by the Kyoto Protocol

ASH-09AISR

Model

SPLIT AIR CONDITIONER

INDOOR UNIT

Rated Voltage

220-240V~
Rated Frequency 50Hz
Cooling Capacity 3500W
Heating Capacity 3810W
Air Flow Volume

3

560m /h
Sound Pressure Level(H) 36dB(A)
Weight

11.5kg

Manufactured Date

63229936476

Sinclair Corporation Ltd, 1-4 Argyll St., London, UK

ISO9001

TUV

ASH-13AISW

ISO9001

TUV

AIR CONDITIONER OUTDOOR UNIT

63229936477

Sinclair Corporation Ltd, 1-4 Argyll St., London, UK

Model

Rated Voltage

220-240V~

(ISO 5151)

3500W

Rated Frequency

50Hz

Cooling Capacity

3810W

Climate Type

T1

Heating Capacity

970W

Weight

38kg

Cooling Power Input

1055W

Isolation

I

Heating Power Input

Refrigerant

R410A

Cooling Rated Input

1500W

Refri. Charge

1.26kg

Heating Rated Input

1600W

Comp. LRA

25A

Sound Pressure Level

52dB(A)

2.8/1.2MPa

3.8MPa

Manufactured Date

Moisture Protection

I P24

Operating Pressure ( Discharge Si de/Suction Si de)

Maximum Allowable Pressure

Contains fluorinated greenhouse gases covere d by the Kyoto Protocol

ASH-13AISW

Model

SPLIT AIR CONDITIONER

INDOOR UNIT

Rated Voltage

220-240V~
Rated Frequency 50Hz
Cooling Capacity 3500W
Heating Capacity 3810W
Air Flow Volume

3

560m /h
Sound Pressure Level(H) 36dB(A)
Weight

11.5kg

Manufactured Date

63229936474

Sinclair Corporation Ltd, 1-4 Argyll St., London, UK

ISO9001

TUV

ASH-13AISB

ISO9001

TUV

AIR CONDITIONER OUTDOOR UNIT

63229936475

Sinclair Corporation Ltd, 1-4 Argyll St., London, UK

Model

Rated Voltage

220-240V~

(ISO 5151)

3500W

Rated Frequency

50Hz

Cooling Capacity

3810W

Climate Type

T1

Heating Capacity

970W

Weight

38kg

Cooling Power Input

1055W

Isolation

I

Heating Power Input

Refrigerant

R410A

Cooling Rated Input

1500W

Refri. Charge

1.26kg

Heating Rated Input

1600W

Comp. LRA

25A

Sound Pressure Level

52dB(A)

2.8/1.2MPa

3.8MPa

Manufactured Date

Moisture Protection

I P24

Operating Pressure ( Discharge Side/Suction Side)

Maximum Allowable Pressure

Contains fluorinated greenhouse gases covere d by the Kyoto Protocol

ASH-13AISB

Model

SPLIT AIR CONDITIONER

INDOOR UNIT

Rated Voltage

220-240V~
Rated Frequency 50Hz
Cooling Capacity 3500W
Heating Capacity 3810W
Air Flow Volume

3

560m /h
Sound Pressure Level(H) 36dB(A)
Weight

11.5kg

Manufactured Date

63229936472

Sinclair Corporation Ltd, 1-4 Argyll St., London, UK

ISO9001

TUV

ASH-13AISR

ISO9001

TUV

AIR CONDITIONER OUTDOOR UNIT

63229936473

Sinclair Corporation Ltd, 1-4 Argyll St., London, UK

Model

Rated Voltage

220-240V~

(ISO 5151)

3500W

Rated Frequency

50Hz

Cooling Capacity

3810W

Climate Type

T1

Heating Capacity

970W

Weight

38kg

Cooling Power Input

1055W

Isolation

I

Heating Power Input

Refrigerant

R410A

Cooling Rated Input

1500W

Refri. Charge

1.26kg

Heating Rated Input

1600W

Comp. LRA

25A

Sound Pressure Level

52dB(A)

2.8/1.2MPa

3.8MPa

Manufactured Date

Moisture Protection

I P24

Operating Pressure ( Discharge Si de/Suction Si de)

Maximum Allowable Pressure

Contains fluorinated greenhouse gases covere d by the Kyoto Protocol

ASH-13AISR

Energy

Manufacturer

Unit model

More efficient

Less efficient

Air cooled
Water cooled

Noise

(() )

dB A re 1 pW

Further information is contained
in product brochures

Norm EN 14511
Air-conditioner
Energy Label Directive 2002/31/ CE

323

2.6

4.03

Type

Cooling only
Cooling+Heating

kW

Heat out put
Heating performance

A: higher

G: lower

Annual Energy Consumption
kWh in cooling mode

( Actual consumption will depend

on how the appliance is used
and climate)

Cooling output
Energy Efficiency Ratio

Full load ( the higher the better )

kW

2.87

A

B

CDEFG

A

A

B

C

D

E

F

G

ASH-09AISB

44/60

62229924358

Energy

Manufacturer

Unit model

More efficient

Less efficient

Air cooled
Water cooled

Noise

(() )

dB A re 1 pW

Further information is contained
in product brochures

Norm EN 14511
Air-conditioner
Energy Label Directive 2002/31/ CE

323

2.6

4.03

Type

Cooling only
Cooling+Heating

kW

Heat output
Heating performance

A: higher

G: lower

Annual Energy Consumption
kWh in cooling mode

( Actual consumption will depend

on how the appliance is used
and climate)

Cooling output
Energy Efficiency Ratio

Full load ( the higher the better )

kW

2.87

A

B

CDEFG

A

A

B

C

D

E

F

G

ASH-09AISW

44/60

62229924359

Energy

Manufacturer

Unit model

More efficient

Less efficient

Air cooled
Water cooled

Noise

(() )

dB A re 1 pW

Further information is contained
in product brochures

Norm EN 14511
Air-conditioner
Energy Label Directive 2002/31/ CE

323

2.6

4.03

Type

Cooling only
Cooling+Heating

kW

Heat output
Heating performance

A: higher

G: lower

Annual Energy Consumption

kWh in cooling mode

( Actual consumption will depend

on how the appliance is used
and climate)

Cooling output
Energy Efficiency Ratio

Full load ( the higher the better )

kW

2.87

A

B

CDEFG

A

A

B

C

D

E

F

G

ASH-09AISR

44/60

62229924357

Energy

Manufacturer

Unit model

More efficient

Less efficient

Air cooled
Water cooled

Noise

(() )

dB A re 1 pW

Further information is contained
in product brochures

Norm EN 14511
Air-conditioner
Energy Label Directive 2002/31/ CE

485

3.5

3.61

Type

Cooling only
Cooling+Heating

kW

Heat output
Heating performance

A: higher

G: lower

Annual Energy Consumption
kWh in cooling mode

( Actual consumption will depend

on how the appliance is used
and climate)

Cooling output
Energy Efficiency Ratio

Full load ( the higher the better )

kW

3.81

A

B

CDEFG

A

A

B

C

D

E

F

G

ASH-13AISB

44/60

62229924361

Energy

Manufacturer

Unit model

More efficient

Less efficient

Air cooled
Water cooled

Noise

(() )

dB A re 1 pW

Further information is contained
in product brochures

Norm EN 14511
Air-conditioner
Energy Label Directive 2002/31/ CE

485

3.5

3.61

Type

Cooling only
Cooling+Heating

kW

Heat out put
Heating performance

A: higher

G: lower

Annual Energy Consumption

kWh in cooling mode

( Actual consumption will depend

on how the appliance is used
and climate)

Cooling output
Energy Efficiency Ratio

Full load ( the higher the better )

kW

3.81

A

B

CDEFG

A

A

B

C

D

E

F

G

ASH-13AISW

44/60

62229924362

Energy

Manufacturer

Unit model

More efficient

Less efficient

Air cooled
Water cooled

Noise

(() )

dB A re 1 pW

Further information is contained
in product brochures

Norm EN 14511
Air-conditioner
Energy Label Directive 2002/31/ CE

485

3.5

3.61

Type

Cooling only
Cooling+Heating

kW

Heat output
Heating performance

A: higher

G: lower

Annual Energy Consumption
kWh in cooling mode

( Actual consumption will depend

on how the appliance is used
and climate)

Cooling output
Energy Efficiency Ratio

Full load ( the higher the better )

kW

3.81

A

B

CDEFG

A

A

B

C

D

E

F

G

ASH-13AISR

44/60

62229924360