Page 1
USER'S MANUAL
ASH-09AIP PT, ASH-12AIP PT
POLAR
SERIES
Page 2
Page 3
This symbol stands for the items
should be forbidden.
This symbol stands for the items
should be followed
■
Installation and Maintenance of Healthy Filter .......................... 24
■
Install snow guard (Optional) ................................................ 25
Do not dispose this product as unsorted municipal waste.
Collection of such waste separately for special treatment
is necessary.
The products in this manual may be different with the real one, according to different
models, some models have displayer and some models without displayer, the position
and shape of the displayer please refer to the real one.
This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities or lack of experience and knowledge,
unless they have been given supervision or instruction concerning use of the appliance
by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
CONTENTS
■
■
■
■
■
■
■
■
■
■
■
Operation and maintenance
Notices for operation ............................................................. 1
Notices for use .................................................................... 3
Names and functions of each part ........................................... 5
■
Operation of wireless remote control ........................................ 6
Clean and care .................................................................. 12
Troubleshooting ................................................................. 14
Installation service
Notices for installation ......................................................... 17
Installation dimension diagram
.............................................. 19
Install indoor unit
................................................................ 20
Install outdoor unit
.............................................................. 22
Check after installation and test operation ............................... 23
Emergency operation .......................................................... 11
Page 4
★
★
★
Operation and maintenance-notices for operation
１
★
★Be sure to pull out the power
★
★
★
★
Earth: The ground
be connected!
If not, please ask the qualified person-
nel to install. Furthermore, don't conn-
ect each wire to the gas pipe, water
pipe, drainage pipe or any other improper places.
plug when not using the air conditioner for a long time.
Otherwise, the accumulated dust
may cause fire or electric shock.
Select the most appropriate tem-
perature.
Keep room cool-
er than outside
about 5 degree.
It can preclude the electricity wasted.
Don't leave windows and
doors open for a long time
while operating the air conditioner.
It can decrease the air conditioning
capacity.
Don't block the air intake or outlet
vents of both the outdoor and indoor
units.
It can decrease the air conditioning
capacity or cause a malfunction.
Keep combustible spray away
from the units more than 1m.
It can cause afire or explosion.
If it is damaged, it may lead to
the fall of the unit and cause
the injury.
Please note whether the installed
stand is firm enough or not.
Don't step on the top of the
outdoor unit or place something
on it.
As falling off the outdoor unit
can be dangerous.
Don't attempt to repair
the air conditioner by yourself.
The wrong repair will lead to
an electric shock or fire, so
you should contact the service
center to repair.
Page 5
２
★
★
★
★
★
★
★
★
Notices for operation
If the supply cord is damaged, it must be replaced
by the manufacturer or its service agent or a
similarly qualified person in order to avoid a
hazard.
The airflow direction can be adjusted appropriately. At operating, adjust the vertical airflow
direction by adjusting the louvers of upward/downward direction. And then, hold two ends of
left and right louver to adjust the horizontal airflow.
Louver of left/right directionLouver of upward/
downward direction.
Don't insert your hands or stick into the air
intake or outlet vents.
Otherwise it will cause accident.
Don't blow the wind to animals and plants
directly. It can cause a bad influence to them.
Don't apply the cold wind to the body for a
long time.
It can cause the health problems.
Don't use the air conditioner for other purposes,
such as drying clothes, preserving foods, etc.
Splashing water on the air conditioner can
cause an electric shock and malfunction.
Don't place a space heater near the air
conditioner.
Or CO toxicosis may occur for imcomplete
burning.
Page 6
.
Anti-cool wind function:
In "Heat" mode, under the following three kinds of state, if indoor heat exchanger doesn't
arrive at certain temp., indoor fan will not act, in order to prevent cool wind blowing(within
2 mins):
1. Heating starts. 2. After Auto Defrost finished. 3. Heating under the low temperature.
Gentle Breeze
In the following situation, the indoor unit may blow gentle breeze, and
the guide louver rotate to a certain position:
1. In “Heat” mode, the unit turned on, the compressor doesn’t arrive the starting condition
2. In “Heat” mode, the temperature arrive at the setting value and the compressor stop
running about 1min.
*
*
*
*
*
*
Notices for use
Working principle and special functions for cooling
Principle:
Anti-freezing function:
Working principle and special functions for heating
Principle:
Defrosting:
Air conditioner absorbs heat in the room and transmit to outdoor and discharged, so that
indoor
ambient temperature decreased, its cooling capacity will increase or decrease by
outdoor ambient temperature.
If the unit is running in COOL mode and in low temperature, there will be frost formed on
the heat exchanger, when indoor heat exchanger temperature decreased below 0 , the
indoor unit microcomputer will stop compressor running and protect the unit.
℃
Air conditioner absorbs heat from outdoor and transmits to indoor, in this way to increase
room temperature. This is the heat pump heating principle, its heating capacity will be
reduced due to outdoor temperature decrease.
If outdoor temperature becomes very low, please operate with other heating equipments.
When outdoor temperature is low but high humidity, after a long while running, frost will
form on outdoor unit, that will effect the heating effect, at this time, the auto defrosting
function will act, the heat running will stop for 8-10mins.
During the auto defrosting, the fan motors of indoor unit and outdoor unit will stop.
During the defrosting, the indoor indicator flashes, the outdoor unit may emit vapor.
This is due to the defrosting, it isn't malfunction.
After defrosting finished,the heating will recover automatically.
3
Page 7
4
Notices for use
The operating temperature range (outdoor temperature) for cooling unit is -15℃
~
46℃；
for cooling and heating unit is -15℃
~
24℃.
Working temperature range
Maximum cooling
Minimum cooling
Maximum heating
Minimum heating
Indoor sideDB/WB(oC)
Outdoor sideDB/WB(oC)
32/23
21/15
27/--20/---
-15/--
24/18
-15/--
46/---
Page 8
Names and functions of each part
⑹
⑸
⑵
⑻
⑷
⑺
⑶
⑴
Indoor unit
Outdoor unit
Wireless
remote control
Power cable
Remote control
Front panel
Filter
Guide louver
Wall pipe
Bind tape
Drainage pipe
⑹
⑺
Receive window
Heat
Cool
Run
Dry
SET TEMP
ON/OFF
5
Air out
Air in
⑻
Air out
Air in
⑻
Air in
Air out
⑶
⑸
⑴
⑷
⑵
Page 9
●
AUTO
COOL
DRY
FAN
HEAT
FAN
FAN speed button
Press this button once, fan speed will change
as below:
Auto
Low speed Middle speed
High speed
Note:Under the Dry mode, the fan speed isn't
●
Simpleness swing mode is defaulted for wireless
remote control, in this mode, press this button,
(＋/－)
16～30℃。
●
Names and functions of remote control buttons
Note: Be sure that there are no obstructions between receiver and remote control; Don't drop
or throw the remote control; Don't let any liquid in the remote control and put the remote control
directly under the sunlight or any place where is very hot
.
Signal transmitter
Remote control
ON/OFF
ON/OFF button
Press this button, the unit will be started or stopped,
which can clear the timer or sleeping function of
last time.
●
TEMP(+/-) button
When press +button , the setting temp. will b
e
increased by 1 ,When press -button,the
setting temp. will be decreased by 1
The temp. will be changed quickly
the button continuously and setting temp. range
℃
is
by pressing
●
●
●
Operation of wireless remote control
Swing up and down button
℃
below.
Press this button, the running mode
will change as
Mode button
MODE
FAN
AUTO
OPER
HEALTH
AIR
FILTER
TURBO
ON/OFF
X-FAN
HOUR
HUMIDITY
ON/OFF
MODE
FAN
X-FAN
TURBO
TEMP
TIMER
SLEEP
LIGHT
could turn on or turn off the Up and down
swing function.
When unit is turned off, synchronously press
"+" and Up and down swing buttons, it could
be switched between the simpleness swing
mode and stationary swing mode, at this time,
blinks 2 seconds.
In Stationary swing mode, press this button,the
angle for Up and down swing as show in below:
When up and down swing louver is working,
when turn off the unit, the siwng louver will
●
immediately stop at current position.
shows up and down swing louver swings back
and forth as show in the above figure.
adjustable, low fan speed is imperative,
but when operating this button, the wireless
remote control will send this signal.
6
(Only for cooling and heating unit.)
(As for cooling only unit, it won’t have
any action when it receives the signal
of heating operation. )
Page 10
7
HEALTH function:there is no this function
for this unit. If press this key, the main unit
will click, but it also runs under original status.
Health
save
HEALTH
SAVE
FAN
AUTO
OPER
HEALTH
AIR
FILTER
TURBO
ON/OFF
X-FAN
HOUR
HUMIDITY
ON/OFF
MODE
FAN
X-FAN
TURBO
TEMP
TIMER
SLEEP
LIGHT
Operation of wireless remote control
TIMER
●
NOTE: This Remote control is universal, it c o uld be used formany units, some buttons
of this control which are not availabl e to this unit will not be described below.
On the status of the unit on, press this
button to set timer off. On the status of
the unit off, press this button to set timer
off. Press this key once, words Hour on(off)
will appear and flicker. In which case, press
+/- button to adjust time (press+/- button
the setting time range is from 0.5 to 24 hr.
;
continuously to change timing value quickly
),
then remote controller will send out the signal
immediately and hour on/off will stop flickering.
If the time of that no press timer button
under flickering status is above 5s,the timer
setting will quit. If the timer has been set,
press this button once again to quit it.
press this key once again to fix the time,
●
Remote control
TURBO
Turbo button
Set turbo on or off (the characters of turbo
will appear or disappear ) by pressing this
●
key unde r cooling or heating mode.Once
energized, the unit will be defaulted to be
turbo off. This function can not be set under
of turbo won't appea r .
auto, dehumidify or fan mode, and characters
button
Timer button
Names and functions of remote control buttons
Left and right swing button
There is no this function
for this unit. If press
this key, the main unit
will click, but it also
runs
under original status.
●
“Electricity Save mode”, repress this button,
the whole unit will quit this mode, other mode
button is not available. Under the EnergySave
mode, the Temperature and the Fan speed
on the remote control are not adjustable.
●
Save energy function: Under Cool mode,press
the right part of this button, the remote control
will display“ ”, the whole unit will enter into
Page 11
1
2 hours later
setting temp.
●
℃
●
●
●
●
NOTE: This remote control is universal, it could be used formany units, some
buttons of this control which are not available to this unit will not be
described below.
Names and functions of remote control buttons
Operation of wireless remote control
X-FAN button
Set X-FAN on (the characters of X-FAN will
appear)or off (the characters of X-FAN
disappear ) by pressing this key under
cool or dehumidify mode. Once energized,
the unit will be defaulted to be X-FAN off.
This function can not be set under auto,
fan or heat mode, and the characters of
X-FAN won't appear.
Note：
X-FAN is the alternative expression
of BLOW for the purpose of understanding.
Press this button to select LIGHT on or off
in the displayer. When the LIGHT on is
set,the icon will be displayed and the
indicator light in the displayer will be on.
When the LIGHT off is set, the icon will
be displayed and the indicator light in the
displayer will be off.
Light button
LIGHT
Press this button, enter into SLEEP state,
when repressed, it will quit. The sleep function
and FAN mode.
will be canceled with the stop of the unit.
There is no SLEEP function under AUTO
is the icon for sleep
function.
SLEEP
Sleep button
At COOL, DRY mode: the SLEEP mode runs
after 1hour, the setting temp. will be increased
by 1 , 2 hour later, setting temp. will be
increased by 2 and then will run at this
setting temperature.
after 1hour, the setting temp
will be
At HEAT mode: the SLEEP mode runs
decreased by
,
then it will run
at setting temperature.
℃
℃
℃
will be decreased by
2
Remote control
X-FAN
FAN
AUTO
OPER
HEALTH
AIR
FILTER
TURBO
ON/OFF
X-FAN
HOUR
HUMIDITY
ON/OFF
MODE
FAN
X-FAN
TURBO
TEMP
TIMER
SLEEP
LIGHT
Press this button, (display ), display
the presetting temperature; (display ),
display indoor ambient temperature,
will not change current display status. If
current display status is indoor ambient temp.
when received other remote control sginal,
then will display presetting temp., 5s later
return to ambient temp. display.
Other models haven't this function. But
pressing this button, the main unit will click
and keep the original status.
no signal display on the remote control).
●
After powered on, displaying presetting
temperature is defaulted,(According to
customer requirements to display,if there
are no requirements,the presetting temperature displaying is defaulted, there is
TEMP
Temp. display button
8
Page 12
Guide for operation-general operation
★
cheduled timer on or timer off.
ON/OFF
MODE
FAN
X-FAN
TURBO
SLEEP LIGHT
TEMP TIMER
ON/OFF
MODE
FAN
X-FAN
TURBO
SLEEP LIGHT
TEMP TIMER
1. Press ON/OFF button to start the unit after powering
the main unit on. (Note: Power the unit on every time,
the big -guide louver and small-guide louver will be
closed firstly.
)
2. Press MODE button to select desired running mode.
3.
Press +/ - button to set the desired temperature
.
(It is unnecessary to set the temperature at AUTO mode)
4. Press FAN button to set fan speed, the AUTO FAN,
LOW, MID or HIGH could be selected.
5. Press button to set swing mode.
1.
Press SLEEP button, set the sleep mode.
2. Press TIMER button, then press +/- button, to set the
3. Press light button to control displayer light on or off.
4. Press X-FAN button to set X-FAN function on or off.
5. Press turbo button to set this function on or off.
Guide for operation-optional operation
Introduction for special function
This function indicates that moisture on evaporator of indoor unit will be blowed after the unit
About X-FAN function
is stopped to avoid mould.
1. Having set X-FAN function on: After turning off the unit by pressing ON/OFF button
indoor fan will continue running for about 10 min. at low speed. In this period,
press X-FAN button to stop indoor fan directly.
2. Having set X-FAN function off: After turning off the unit by pressing ON/OFF button,
the complete unit will be off directly.
Operation of wireless remote control
９
Page 13
1.
Changing batteries and notices
4.
2.
3.
★
●
●
●
●
●
Slightly to press the place with , along the arrowhead direction to push the back cover of wireless
remote control. (As show in figure)
Take out the old batteries. (As show in figure)
Insert two new AAA1.5V dry batteries, and pay attention to the polarity.
(As show in figure)
Attach the back cover of wireless remote control. (As show in figure)
When changing the batteries, do not use the old or different batteries,
If the wireless remote control will not be used for a long time, please
otherwise, it can cause the malfunction of the wireless remote control.
take them out, and don't let the leakage liquid damage the wireless
remote control.
The operation should be in its receiving range.
It should be placed at where is 1m away from the TV set or stereo sound sets.
If the wireless remote control can not operate normally, please take them out,
after 30s later and reinsert, if they cannot normally
run, please change them.
Sketch map for
changing batteries
NOTE:
Fig.1
Fig.2
★
★
★
★
★
About lock
About AUTO RUN
About new function of defrosting
will be displayed on it, in which case, press any button, the mark will
When AUTO RUN mode is selected, the setting temperature will not be displayed on the
LCD, the unit will be in accordance with the room temp. automatically to select the suitable
running method and to make ambient comfortable.
About turbo function
If start this function, the unit will run at super-high fan speed to cool or heat quickly so that
the ambient temp. approachs the preset temp. as soon as possible.
Press +and - buttons simultaneously to lock or unlock the keyboard. If the remote controller
is locked, the icon
flicker for three times. If the keyboard is unlocked, the mark will disappear.
About switch between Fahrenheit and Centigrade
Under status of unit off, press MODE and - buttons simultaneously to switch℃
and
．
It indicates: after starting this function by remote controller and the unit has been under
defrost status, If turn off the unit by remote controller, the unit will not stop defrosting until
it is finished; if change setting mode by remote controller, the function ,which is set last
time, won't be carried out until defrosting finished
.
Operation of this function on or off: If remote controller is under off status, press mode button
and X-FAN button simultaneously in order to enter or cancel this new function. If the unit is under
defrost mode, dual eight position on remote controller will display H1.If switch to heat mode,
the position will display H1, which flickers for 5s, in which case, press +/- button, H1 will
disappear and setting temp. be displayed.
After remote controller is powered on, the new defrost function will be defaulted to be
closed.
Operation of wireless remote control
１０
Page 14
Get the displayer indicator light off: If cancel the light function,the mark will disap-
per on the remote controller screen by pressing this
button. In which case, the displayer indicator light will
be off if the AC receives this signal.
●
If the wireless remote control is lost
or broken, please use the manual switch
Auto mode, but the temperature and fan
button. At this time, the unit will run at the
To open the panel, the manual switch
is on the displayer box.
It's a special selective button for the users ,who are not accustomed to the
light at sleeping.
Get the displayer indicator light on: When setting the light function,the mark will
pressing this button. In which case,the dissplayer indicator light will be on if the AC receives
Displayer indicator light control of indoor unit
●
display on the remote controller screen by
this signal.
Emergency operation
Emergency operation
speed cannot be changed. The operation
was shown as below:
Turn on the unit: At unit turned off, press
the button,the unit will run at Auto mode
immediately.The microcomputer will accord
●
to the indoor temperature to select (Cooling,
Heating, Fan) and obtain the comfortable effect.
Turn off the unit: At unit turned on, press the
button, the unit will stop working.
●
Manual switch
Fig.3
１１
Page 15
℃
●●
●●
●
℃
② Clean the air filter
③
①
(a)
(b)
Clean and care
Caution
Turn power off and pull out the power plug before cleaning air conditioner, or it may cause electric
shock.
Never sprinkle water on the indoor unit and the outdoor unit for cleaning because it can cause an
electric shock.
Volatile liquid (e.g. thinner or gasoline) will damage the air conditioner. (So wipe the units with a
dry soft cloth, or a cloth slightly moistened with water or cleanser.)
Clean the front panel
Clean the air filter (Recommended once every three months)
NOTE: If dust is much more around the air conditioner, the air filters should be cleaned many times.
After taking off the filter, don't touch the fin of indoor unit, in order to avoid hurt your fingers.
Take down the air filter
At the slot of surface panel to open an angle, pull the air filter
downward and take it out, please see the Fig. 4 (a, b).
To clean the dust adhering to the filters, you can either
use a vacuum cleaner, or wash them with warm water
the water with the neutral detergent should below 45
degree), and dry it in the shade.
NOTE: Never use water above 45 to clean, or it can
cause deformation or discoloration. Never parch it by
fire, or can cause a fire or deformation.
Insert the air filter
Reinsert the filters along the direction of arrowhead, and
then to cover the cover and clasp it.
Fig.4
When cleaning the front panel, please dip the cloth into the water temperature of 45 below, then to dry
the cloth and wipe the dirty part.
Note: Please do not to immerse the front panel in water, due to there are microcomputer components and
circuit diagrams on the front panel.
１２
Page 16
① Be sure that nothing obstructs the air outlet and intake vents.
②
③
Check that whether the batteries of air conditioner are
changed or not.
④ Check that whether the installation stand of the outdoor
unit is damaged or not. If damaged, please contact the dealer.
①
②
③
④
⑤
Clean and care
Check before use
Check that whether ground wire is properly connected or not.
Maintain after use
Turn main power off.
Clean the filter and indoor and outdoor units' bodies.
Clear dust and obstructions from the outdoor unit.
Repaint the rubiginous place on the outdoor unit to prevent it from spreading.
Adopt the special shield to cover the outdoor unit, avoid the rain water, dust enter into
the unit and get rust.
１３
Page 17
Once the air conditioner is stopped, it will
not operate in approximately 3 minutes to
protect itself.
●
●
●
●
●
●
Troubleshooting
CAUTION
Don't attempt to repair the air conditioner by yourself, it can cause an electric shock or
fire. Please check the following items before asking for repair, it can save your time and
money.
Phenomenon
Troubleshooting
Not operate immediately when the air
conditioner is restarted.
There's unusual smell blowing from the outlet
after operation is started.
The unit has no peculiar smell by itself. If has,
that is due to the smell accumulated in the
ambient.
Solution method: Cleaning the filter.
If problem still has, so need to clean air
conditioner. (Please contact with the authorized
maintenance center.)
Sound of water flow can be heard during
the operation.
The air conditioner is started, when it is
running the compressor started or stopped
running, or the unit is stopped, sometimes
there is swoosh or gurgle, the sound is due
to refrigerant flowing they are not malfuncti ons.
In COOL mode, sometimes the mist emitted
from the air outlet vent.
When the indoor temperature and humidity
are very high, this phenomenon would
happen. This is caused by the room air is
swiftly cooled down. After running for a while,
indoor temperature and humidity will fall
down, the mist will die away.
Creaking noise can be heard when start or
stop the unit.
This is caused by the deformation of plastic
due to the changes of temperature.
Waiting
１４
Page 18
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
Troubleshooting
Phenomenon
Troubleshooting
The unit can not run.
Has the power been shut down?
Is power plug loosed?
Is the circuit protection device tripped off or not?
Is voltage higher or lower?
(Tested by professionals)
Is the TIMER correctly used?
Cooling(Heating) efficiency is not good.
Is Temp. setting suitable?
Were inlet and outlet vents obstructed?
Is filter dirty?
Are the windows and doors clothed?
Did Fan speed set at low speed?
Is there any heat sources in the room?
Wireless remote control is not available.
The unit is interfered by abnormal or frequent
functions switchover occasionally the controller
cannot operate. At this time, you need to pull out
of the plug, and reinsert it.
Is it in its receiving range? Or obstructed?
To check the voltage in wireless remote control inside
is charged, otherwise to replace the batteries.
Whether the wireless remote control is damaged.
If water leakage in the room. The air humidity is on the high side.
Condensing water over flowed.
The connection position of indoor unit drainage
pipe is loosed.
If water leakage in outdoor unit. When the unit is running in COOL mode, the pipe
and connection of pipe would be condensed due
to the water cooled down.
When the unit is running in Auto Defrosting mode
the ice thawed and flowed out.
When the unit is running in HEAT mode, the water
adhered on heat exchanger dripped off.
Noise from indoor unit emitted. The sound of fan or compressor relay is switching
on or off.
When the defrosting is started or stop running,
it will sound. That is due to the refrigerant flowed
to the reverse direction.
Breaking off
１５
Page 19
●
●
●
●
●
Troubleshooting
Phenomenon
Troubleshooting
Indoor unit cannot deliver air.
Moisture on air outlet vent
.
If unit is running under the high humidity for
a long time, the moisture will be condensed
on the air outlet grill and drip off.
Immediately stop all operations and plug out, contact
the dealer in following situations.
There is harsh sound during operation.
The terrible odors emitted during operation.
Water is leaking in the room.
Air switch or protection switch often breaks.
Carelessy splash water or something into unit.
There is an abnormal heat in power supply cord
and power plug.
Stop running and pull out of the plug.
In HEAT mode, when the temperature of indoor
heat exchanger is very low, that will stop deliver
air in order to prevent cool air. (Within 2min)
In HEAT mode, when the outdoor temperature
is low or high humidity, there are much frost be
formed on the outdoor heat exchanger, that the
unit will automatically defrost, indoor unit stop
blowing air for 3-12min.
During the defrosting, there is water flowing out
or vapor be produced.
In dehumidifying mode, sometimes indoor fan will
stop, in order to avoid condensing water be vaporized again, restrain temperature rising.
16
H1: Defrosting It is normal.
Page 20
1.
2.
Select a position where the condensing water can be easily drained out, and the place
is easily connected for outdoor unit.
4.Can select the place where is strong enough to withstand the full weight and vibration o
f
the unit. And will not increase the noise.
5.
6.
7.
8.
Make sure that the indoor unit installation should accord with installation dimension
diagram requirements.
3.
Select a location where the children can not reach.
●
●
1.The unit installation work must be done by qualified personnel according to the local
rules and this manual.
2.Before installation, please contact with local authorized maintenance center, if unit is
not installed by the authorized maintenance center, the malfunction may not solved,
due to discommodious contacts.
3.W
4
.the appliance must be positioned so that the plug is accessible
hen removing the unit to the other place, please firstly contact with the authorized
Maintenance Center in the local area.
●
●
●
●
Notices for installation
Important Notices
Basic Requirements F
or Installation Position
Install in the following place may cause malfunction. If it is unavoidable contact with
service center please:
Place where strong heat sources, vapors, flammable gas or volatile object are emitted.
Place where high-frequency waves are generated by radio equipment, welders and
medical equipment.
Place where a lot of salinities such as coast exists.
Place where the oil (machine oil) is contained in the air.
Place where a sulfured gas such as the hot spring zones is generated.
Other place with special circumstance.
Indoor Unit Installation Position Selection
The air inlet and outlet vent should be far from the obstruction, make sure that the air
can be blown through the whole room.
Be sure to leave enough space to allow access for routine maintenance. The height of the
installed location should be 250cm or more from the floor.
Select a place about 1m or more away from TVset or any other electric appliances.
Select a place where the filter can be easily taken out.
.Do not use the unit in the immediate surroundings of a laundry a bath a shower or a
swimming pool.
9
17
1
.
Select a location from which noise and outflow air emitted by unit will not inconvenience
neighbors, animals, plants.
2
.
Select a location where there should be sufficient ventilation.
3
.
Select a location where there should be no obstructions cover the inlet and outlet vent.
4
.
The location should be able to withstand the full weight and vibration of the outdoor unit
and permit safe installation.
5
.
Select a dry place, but do not expose under the direct sunlight or strong wind.
6
.
7.
8.
9.
Outdoor Unit Installation Position Selection
Make sure that the outdoor unit installation dimension should accord with installation
dimension diagram, convenient for maintenance, repair.
The height difference of connecting the tubing within 5m, the length of connecting the
tubing within 10m.
Select a place where it is out of reach for the children.
Select a place where will not block the passage and do not influence the city appearance.
Page 21
Note:
Make sure that the Live wire or Zero line as well as the earth wire in the family power
socket can not be wrong connected, there should be reliable and no short circuit in the
diagram.
wrong connection may cause fire.
●
●
4. The min. distance from the unit and combustive surface is 1.5m.
1. The power supply should be used the rated voltage and AC exclusive circuit,
the power cable diameter should be satisfied.
2. Don't drag the power cable emphatically.
3.
① ②
③
④
1. Air conditioner is type I electric appliance, thus please do conduct reliable earthing
measure.
2. The yellow-green two-color wire in air conditioner is earthing wire and cannot be used
for other propose. It cannot be cut off and be fix it by screw, otherwise it would cause
electric shock.
3. The earth resistance should accord to the National Criterion.
4. The user power must offer the reliable earthing terminal. Please don't connect the
earthing wire with the following place:
Tap water pipe. Gas pipe.
Contamination pipe.
Other places that professional personnel consider them unreliable.
5. The appliance shall be installed in accordance with national wiring regulations.
An all-pole disconnection switch having a contact separation of at least 3mm in all poles
7. Including an air switch with suitable capacity, please note the following table. Air switch
should be included magnet buckle and heating buckle function, it can protect the circuit-short
and overload. (Caution: please do not use the fuse only for protect the circuit)
should be connected in fixed wiring.
It should be reliably earthed, and it should be connected to the special earth device,
the installation work should be operated by the professional.
The air switch must have the functions of magnetic tripping and heat tripping, in order
to
protect the short circuit and overloading.
6.
5. The model and rating values for fuses according the silk print on fuse cover or related
PCB board.
Notices for installation
Safety Requirements For Electric Appliances
Earthing requirements
18
09K
Air switch capacityModels
16A
12K
16A
For models with a power plug, make sure the plug
is within reach after installation.
Page 22
Installation dimension diagram
Installation dimension diagram
Space to the ceiling
Space to the wall
Space to the wall
Air outlet side
Space to the floor
Above
Above
Above
Above
Above
The dimensions of the space necessary for correct
installation of the appliance including the minimum
permissible distances to adjacent structures
●
19
Space to the wall
Above
Above
Space to the obstruction
Air outlet side
Space to the wall
Air inlet side
Above
Above
evobA
Space to the wall
Above
Above
Space to the obstruction
Air outlet side
Space to the wall
Air inlet side
Above
Above
evobA
Page 23
20
Install indoor unit
mm
0 5 1
mm5 5 φ
mm5 5 φ
mm0 5 1
Ø
5 5
Install the rear panel
1. Always mount the rear panel horizontally. Due to the water tray of indoor unit has been adopted the
both-way drainage design, the outlet of water tray should be adjusted slightly down when installing, that is
taking the outlet of the water tray as the center of a circle, the included angle between the evaporator and
level should be 0 or more, that is good for condensing water drainage.
2. Fix the rear panel on the wall with screws.
(Where is pre-covered with plastic granula)
3.
Be sure that the rear panel has been fixed
firmly enough to withstand the weight of an
adult of 60kg, further more, the weight should
be evenly shared by each screw.
Install the piping hole
1. Make the piping hole (Ф55) in the wall at a slight downward slant to the
outdoor side.
2. Insert the piping-hole sleeve into the hole to prevent the connection piping
and wiring from being damaged when passing through the hole.
Install the water drainage pipe
1. For well draining, the drain hose should be placed at a downward slant.
2. Do not wrench or bend the drain hose or flood its end by water.
3. When the long drainage hose passing through indoor,
should wrap the insulation materials.
Wrenched
Bent
Flooded
Indoor Outdoor
Wall pipe
Seal pad
Fig.5
Wall
Wall
Mark on the middle of it
Gradienter
Left
Right
(Rear piping hole)
(Rear piping hole)
Space
to the
wall
above
Space
to the
wall
above
Connect indoor and outdoor electric wires
1. Open the surface panel.
2. Remove the wiring cover.
3. Route the power connection cord and signal control wire (for cooling and heating unit only) from the
4. Connect the interconnection cord to the terminal block, and then fix the cord with cord anchorge.
5. Reassemble the clampand wiring cover.
back of the indoor unit and pull it toward the front through the wiring hole for connection.
yellow-
green
brown
6. Recover the surface panel.
Fig.6
Page 24
２１
●
●
●
After tighten the screw, slight pull the wire and confirm whether is it firm or not.
●
● The cover plate must be fixed, and tighten the connection wire, if it is poor installed, that
Install indoor unit
NOTE:
When connecting the electric wire if the wire length is not enough, please contact with
the authorized service shop to buy a exclusive electric wire that is long enough and the
joint on the wire are not allowed.
The electric wiring must be correctly connected, wrong connection may cause spare parts
malfunction.
Tighten the terminal screw in order to prevent loose.
If the earth wire is wrong connection, that may cause electric shock.
the dust, moisture may enter in or the connection terminal will be affected by outside force,
and will cause fire or electric shock.
右后
4.
2.
3.
●
1.
⑴
⑵
1.
2.
Install the indoor unit
The piping can be lead out from right, right rear, left
left rear.
When routing the piping and wiring from the left
or right side of indoor unit, cut off the tailings
from the chassis in necessary(Show in Fig.7)
Cut off the tailings 1 when routing the wiring only;
Cut off the tailings 1 and tailings 2 when routing
both the wiring and piping.
Take out the piping from body case, wrap the piping
electric wire, water pipe with tape and pull them
through the piping hole (As show in Fig.8)
Hange the mounting slots of the indoor unit on the
upper tabs of the rear panel and check if it is firm
enough.(As show in Fig.9)
The height of the installed location should be 2. m
or more from the floor.
Install the connection pipe
Align the center of the piping flare with the relevant valve.
Screw in the flare nut by hand and then tighten the
nut with spanner and torque wrench refer to the
following:
NOTE: Firstly connect the connection pipe to indoor unit, then to outdoor unit; pay attention
to the piping bending, do not damage the connection
pipe; the joint nut couldn't tighten too
much, otherwise it may cause leakage.
Spanner
Torque
wrench
Piping
Taper nut
Indoor unit piping
Fig.9
Mounting
plate
Fixing hook
Mounting
baord
Right
Right rear
Fig.8
Left rear
Left
Fig.7
Tailing 1
Tailing 2
Finally wrap it
with tape
Gas side piping
insulation
Water drainage pipe
Liquid side
Piping insulation
Gas side pipe
External connection
electric wire
Liquid side piping
(N·m)
Ф6
Ф 9.52
Ф 12
31～35
15～20
50～55
Ф 16 60～65
Ф 19 70～75
Hex nut diameter
Tightening torque
5
Page 25
Ø
Air purging and leakage test
Condensate drainage of outdoor unit (no for cooling only)
The condensate and defrosting water formd during heating
in the outdoor unit can be properly discharged by drainage
pipe .
Installation method:set the drain connection in 25 hole of the
chassis has been installed and then connect drainage pipe
with drain nozzle,so that condensate and defrosting waer can
be properly discharged
Chassis
Drain
connection
●
●
Install outdoor unit
Electric wiring
NOTE:
Wrong wiring may cause spare parts malfunction.
After the cable fixed, make sure there should be
a free space between the connection and
connection and fixing place on the lead wire.
3.
4.
5.
1.
2.
Disassemble the handle on the outdoor unit right side plate.
Take off cord anchorage. Connect and fix power connect
cord (for cooling and heating unit, connect and fix power
connect cord and signal control wire)to terminal block.
Fix the power connection cable with cord anchorage,
(for cooling and heating unit, use the cord anchorage
to fix the power connection cable and the signal
control wire).
Ensure wire has been fixed well.
Install the handle.
5
-1.0 10 pa
(-76cmHg)..
1. Connect charging hose of manifold valve to charge end of low pressure
valve (both high/low pressure valves must be tightly shut).
2. Connect joint of charging hose to vacuum pump.
3. Fully open handle handle of Lo manifold valve.
4. Open the vacuum pump to evacuate. At the beginning, slightly
loosen joint nut of low pressure valve to check if there
is air coming inside. (If noise of vacuum pump has
been changed, the reading of multimeter is 0) Then
tighten the nut.
5. Keep evacuating for more than 15mins and make
sure the reading of multi-meter is
6. Fully open high/low pressure valves.
7. Remove charging hose from charging end of low pressure valve.
8. Tighten bonnet of low-pressure valve. (As shown in Fig.10)
Fig.10
yellowgreen
yellowgreen
blue
black
brown
blue
black
brown
Handle
3
3
power connect wire
wire clamp
3
INDOOR/OUTDOOR
CONNECT FIG
INDOOR
OUTDOOR
power
connect
wire
22
Liquid pipe
Gas pipe
Valve
cap
Vacuum
gauge
Vacuum pump
Page 26
1.
(1)
Do not switch on power before installation isfinished completely.
(2)Electric wiring must be connected correctly and securely.
(3)Cut-off valves of the connection pipes should be opened.
(4)
2.
(1)
Switch on power, press "ON/OFF" button on the wireless remote control to start
the operation.
(2)
Check after installation and test operation
Check after installation
Items to be checked Possible malfunction
Has it been fixed firmly?
The unit may drop, shake or emit noise.
Have you done the refrigerant leakage test?
It may cause insufficient cooling (heating)
capacity
Is heat insulation sufficient?
It may cause condensation and dripping.
Is water drainage well?
It may cause condensation and dripping.
Is the voltage in accordance with the rated
voltage marked on the nameplate?
It may cause electric malfunction
or damage the part.
Is the electric wiring and piping
connection installed correctly and securely?
It may cause electric malfunction
or damage the part.
Has the unit been connected to a secure
earth connection?
It may cause electrical leakage.
Is the power cord specified?
It may cause electric malfunction
or damage the part.
Is the inlet and outlet been covered? It may cause insufficient cooling (heating)
capacity.
Has the length of connection pipes
and refrigerant capacity been recorded?
The refrigerant capacity is not accurate.
Test Operation
Before test operation
All the impurities such as scraps and thrums must be cleared from the unit.
Test operation method
Press MODE button, to select the COOL, HEAT (Cooling only unit is not available),
FAN to check whether the operation is normal or not.
２３
Page 27
Fig. a
Installation Instructions
1. Forcibly pull the panel for a specific angle
from the two ends of the front panel according
to the arrow direction. Then pull the air filter
2. Mount the healthy filter onto the air filter,(as
shown in Fig.b). If the air filter cannot be installed, please mount the healthy filter on
3. Mount the air filter properly along the arrow
direction in Fig.d, and then close the panel cover.
ion filter can't be cleaned with water, while active carbon, photocatalyst,
low temperature conversion (LTC) catalyst, formaldehyde eliminator, ca-
The healthy filter commonly has its usage lifetime for one year under
normal condition. As for silver ion filter, it is invalid when its surface becomes
according to the installation instruction. Pay special attention to that silver
Take out the healthy filter before cleaning and reinstall it after cleaning
Installation and Maintenance of Healthy Filter
Cleaning and Maintenance
Service Life
●
Healthy filter
Air filter
Healthy filter
downwards to remove it. (See Fig.a)
the front case. (as shown in Fig.c)
Fig. b
Fig. c
Fig. d
techin or mite killing filter can, but can't with brush or hard things. Dry it in
the shade or sun after cleaning, but not by wiping.
black (green).
goods, the latter one shall prevail. The quantity of healthy filters shall be
based on the actual delivery.
This supplementary instruction is provided for reference to the unit with
healthy filter. If the graphics provided herein is different from the physical
２４
Page 28
Installation method of snow guard
Install snow guard
(Optional)
25
Height of base in consideration of snow
(More than 50cm)
More than 50cm
seasonal
(Provide at field)
wind
In consideration of snow during installation of outdoor units
Correct Incorrect
Note: It is required to equip snow guard and a higher foundation base to
prevent snow from covering air inlet and outlet.
Snow guard
Snow guard
(Install in
windward side)
seasonal
wind
Windward side
Height of base in consideration of snow
(More than 50cm)
50cm Above
20cm
Above
100cm Above
The snow guard shall
be wider than the
air conditioner.
The snow guard shall
be wider than the
air conditioner.
WALL
WALL
Page 29
ASH‐09AIPPT ASH‐12AIPPT ASH‐18AIPPT ASH‐24AIPPT
cooling kW 2,65(0,45‐3,23) 3,53(0,60‐3,96) 5,30(1,05‐6,50) 6,45(1,50‐7,00)
heating kW 3,52(0,45‐4,10) 4,10(0,60‐5,13) 5,70(1,00‐7,00) 7,00(1,20‐7,80)
505050
50
MODEL
POLARSERIES
Capacity
H
z
505050
50
220‐240 220‐240 220‐240 220‐240
cooling A 6,30 6,88 11,09 11,09
heating A 6,88 7,32 11,54 11,98
cooling W 800(200‐1350) 1100(220‐1450) 1600(360‐2500) 1985(1500‐7000)
Powercurrent
Powerinput
Powersupply
HzVheatingW
950(200‐1450)
1135(220‐1550)
1578(350‐2600)
1930(350‐2700)
EER 3,30 3,21 3,31 3,25
COP 3,70 3,61 3,61 3,62
Noise‐indoorunit 41/38/30/24 42/39/31/25 45/40/37/32 46/42/37/32
Noise‐outdoorunit max dB(A) 51 53 54 54
W/W
dB(A)
W/W
Airflow 520 560 800 950
Dehumidifyingvolume 1,0 1,2 1,8 2,0
Refrigeranttype/charge R410a/0,7 R410a/1,0 R410a/1,3 R410a/1,4
Liquidside inch/mm ¼/6¼/6¼/6¼/6
gasside inch/mm ⅜/10 ⅜/10 ½/12 ½/12
m
3
/h
type/kg
Pipediameter
l/h
Lengthofconnectionpipe max m 15 20 25 25
Elevation/Dropheight max m 10 10 10 10
IU mm 770x283x201 770x283x201 865x305x215 1008x319x221
OU mm 710x318x550 710x318x550 955x700x396 955x700x396
IU kg 8 9 12 15
Dimension(wxhxd)
g
OU kg 28 30 52 52
cooling °C
‐15~46 ‐15~46 ‐15~48 ‐15~48
heating °C
‐15~24 ‐15~24 ‐15~24 ‐15~24
Thespecificationofproductsissubjecttochangebasedfurtherdevelopmentoftheunitsbytheproducerandcanbechangedwithoutprior
N
etweight
Operatingtemperaturerange
Dataarebasedonfollowingconditions:
Lengthofconnectionpipe:5m
Cooling:indoortemperature27°CDB/19°CWB,outdoortemperature35°CDB/24°CWB
notice
.
Heatingcondition:indoortemperature20°CDB/15°CWB,outdoortemperature7°CDB/6°CWB
Page 30
Page 31
63229939341
ISO9001
TUV
Sinclair Corporation Ltd, 1-4 Argyll St., London, UK
Model ASH-09AIP PT
SPLIT AIR CONDITIONER
INDOOR UNIT
Rated Voltage 220-240V~
Rated Frequency 50Hz
Cooling Capacity 2650W
Heating Capacity 3520W
Air Flow Volum e
3
600m /h
Sound Pressure Level(H) 38dB(A)
Weight 8kg
Manufactured Date
ISO9001
TUV
63229939342
Sinclair Corporation Ltd, 1-4 Argyll St., London, UK
Model
ASH-09AIP PT
Rated Voltage
220-240V~
(ISO 5151)
2650W
Rated Frequency
50Hz
Cooling Capacity
3520W
Climate Type
T1
Heating Capacity
800W
Weight
28kg
Cooling Power Input
950W
Isolation
I
Heating Power Input
Refrigerant
R410A
Cooling Rated Input
1420W
Refri. Charge 0.74kg Heating Rated Input
1550W
Comp. LRA 4A Sound Pressure Level
51dB(A)
3.8/1.2MPa
4MPa
Manufactured Date
Moisture Protection
I P24
Operating Pre ssure ( Discharge Side/Suction Side)
Maximum Allowable Pressure
Contains fluorinated greenhouse gases covered by the Kyoto Protocol
AIR CONDITIONER OUTDOOR UNIT
63229939343
ISO9001
TUV
Sinclair Corporation Ltd, 1-4 Argyll St., London, UK
Model
ASH-12AIP PT
SPLIT AIR CONDITIONER
INDOOR UNIT
Rated Voltage 220-240V~
Rated Frequency 50Hz
Cooling Capacity 3530W
Heating Capacity 4100W
Air Flow Volum e
3
680m /h
Sound Pressure Level(H) 39dB(A)
Weight 9kg
Manufactured Date
ISO9001
TUV
63229939344
Sinclair Corporation Ltd, 1-4 Argyll St., London, UK
AIR CONDITIONER OUTDOOR UNIT
Model
ASH-12AIP PT
Rated Voltage
220-240V~
(ISO 5151)
3530W
Rated Frequency
50Hz
Cooling Capacity
4100W
Climate Type
T1
Heating Capacity
1100W
Weight
30kg
Cooling Power Input
1135W
Isolation
I
Heating Power Input
Refrigerant
R410A
Cooling Rated Input
1550W
Refri. Charge
1.0kg
Heating Rated Input
1650W
Comp. LRA
16.5A
Sound Pressure Level
53dB(A)
4.3/2.5MPa
4.3MPa
Manufactured Date
Moisture Protection
I P24
Operating Pressure ( Discharge Side/Suction Side)
Maximum Allowable Pressure
Contains fluorinated greenhouse gases covered by the Kyoto Protocol
Page 32
Energy
Manufacturer
Unit model
More efficient
Less efficient
Air cooled
Water cooled
Noise
(() )
dB A re 1 pW
Further information is contained
in product brochures
Norm EN 14511
Air-conditioner
Energy Label Directive 2002/31/ CE
Type
Cooling only
Cooling+Heating
kW
Heat output
Heating performance
A: higher
G: lower
Annual Energy Consumption
kWh in cooling mode
( Actual consumption will depend
on how the appliance is used
and climate)
Cooling output
Energy Efficiency Ratio
Full load ( the higher the better )
kW
A
A
B
C
D
E
F
G
ASH-09AIP PT
62229925972
400
2.65
3.31
3.52
A
B
CDEFG
38/51
3.7
Energy
Manufacturer
Unit model
More efficient
Less efficient
Air cooled
Water cooled
Noise
(() )
dB A re 1 pW
Further information is contained
in product brochures
Norm EN 14511
Air-conditioner
Energy Label Directive 2002/31/ CE
Type
Cooling only
Cooling+Heating
kW
Heat output
Heating performance
A: higher
G: lower
Annual Energy Consumption
kWh in cooling mode
( Actual consumption will depend
on how the appliance is used
and climate)
Cooling output
Energy Efficiency Ratio
Full load ( the higher the better )
kW
A
A
B
C
D
E
F
G
ASH-12AIP PT
62229925973
550
3.53
3.21
4.10
A
B
CDEFG
39/53
3.61
Energy
Manufacturer
Unit model
More efficient
Less efficient
Air cooled
Water cooled
Noise
(() )
dB A re 1 pW
Further information is contained
in product brochures
Norm EN 14511
Air-conditioner
Energy Label Directive 2002/31/ CE
Type
Cooling only
Cooling+Heating
kW
Heat output
Heating performance
A: higher
G: lower
Annual Energy Consumption
kWh in cooling mode
( Actual consumption will depend
on how the appliance is used
and climate)
Cooling output
Energy Efficiency Ratio
Full load ( the higher the better )
kW
A
A
B
C
D
E
F
G
ASH-18AIP PT
62229925974
800
5.30
3.31
5.70
A
BCDEF
G
55/64
3.61
Energy
Manufacturer
Unit model
More efficient
Less efficient
Air cooled
Water cooled
Noise
(() )
dB A re 1 pW
Further information is contained
in product brochures
Norm EN 14511
Air-conditioner
Energy Label Directive 2002/31/ CE
Type
Cooling only
Cooling+Heating
kW
Heat output
Heating performance
A: higher
G: lower
Annual Energy Consumption
kWh in cooling mode
( Actual consumption will depend
on how the appliance is used
and climate)
Cooling output
Energy Efficiency Ratio
Full load ( the higher the better )
kW
A
A
B
C
D
E
F
G
ASH-24AIP PT
62229925975
992.5
6.45
3.24
7.00
A
BCDE FG
42/54
3.62
Loading...