Sinclair ASH-09AF, ASH-12AF Operational Manual

AIR CONDITIONING

WALLMOUNTED SPLIT AIR CONDITIONER SINCLAIR

OPERTIONAL MANUAL

ASH-09AF, ASH-12AF

FLAT SERIE

Before operation please carfully read this manual.

Ｃｏｎｔｅｎｔｓ

Structure Principle and Usage

Install Part

and

Repair

Maintenance

Structure and Function

Important Advice 　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　2

Specificate Model and Technical Data 　　　　　　　　　　　　　　　５

Name and Function of Every Button of Wireless Remote Control 6

Operation Guide 　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　8

Install Note Items 9

Install of Indoor Unit 12

Install of Outdoor Unit 14

Trial Run 17

Repair and Maintenance 18

When the unit cannot run normally 19

　　　　　　　　　　　　　　　　　　　　　　　　　　　　　1

Structure Principle and Usage

◆

Structure and Function

Ｉｎｄｏｏｒ
ｕｎｉｔ

Ｐａｎｅｌ

：

Heat

:Cool/Dry
:Run

:Auto

Ａｉｒ　ｉｎ

Air out

Ｆｉｌｔｅｒ

Power plug

Wireless remote control

Ｄｒａｉｎａｇｅ　ｈｏｓｅ

Ｗｉｒｅ　ｃｏｎｎｅｃｔｉｏｎ
ｃｏｖｅｒ　ｐｌａｔｅ

Ａｉｒ　ｉｎ

Front grill of air outlet vent

Connection pipe and wire

Outdoor
unit

Air out

Structure Principle and Usage

Important Advance (Read the follwoing items carefully before using the unit)

ＷＡＲＮＩＮＧ

Insert power plug firm enough
For loose insert may cause electric
shock or fire.

Don't share socket with other

appliances or use prelonged hose.
Or electric shock or fire may

occur.

Don't plug out power plug

when unit is operating.

Or electric shock or fire may

occur.

Don't operate unit with wet

hand for electric shock may occur.

Don't damage wire or use the

wire that is not appointed.
Or electric shock or fire may

occur.

Don't insert finger or stick-

like thing into air inlet and outlet
vents, or damage may occur.

Danger

Don't let cooled air blows body

directly for too long, and don't
set indoor temp. too low for it is

not good for health.

If abnormal phenomenon occurs

(like burning odor etc.), cut off
power supply first, then contact
Gree Service Center. If abnormal

continues, the unit may be damaged
and cause electric shock or fire.

Cut off power

Don't repair the unit yourself

for incorrect repair may cause

electric shock or fire. So, contact
Gree Service Center to have
unit repaired.

Structure Principle and Usage

★Earthing: Earth must be

reliable! Earth wire should be

connected on special earth settings．

If there is no such settings, have it
connected by perfessional personnel

Don't connect earth wire onto gas

pipe, water pipe, blowing pipe or
place where perfessiona personnel
considers it unrealiable.

★Don't plug out the plug by
pulling the power hose.
Otherwise, fire may be caused
for over heat of wire.

★Plug out power plug when the

unit will not be used for a long time.

★Don't let the unit blows to
heater or cooker directly. Or carbon
monoxide poisoning may occur for

incomplete burn.

★Cut off power when cleaning

the unit. Otherwise, electric shock
or damage may occur.

★Chemical sprayer must be

placed 1m away from both indoor
and outdoor unit to prevent fire

or explosionor explosion

★Note if install chassis is
damaged. If the chassis is damaged
without repair, unit may fall down

and cause injury.

★Don't stand or put things on
the outdoor unit. For people or
things may fall down and cause

injury.

★Don't block the air inlet or outlet
vent of both indoor and outdoor unit.
It would cause low performance
or stop of unit.

Structure Principle and Usage

ＮＯＴＩＣＥ

Indoor temperature should be set properly
Proper set temp. can save electricity.

Temp. dif of

indoor and outdoors

should be５℃

When the unit is running, don't open windows
or doors of the room for long time.

It would lower performance of the unit.

Don't pour water on the unit or wash it by water

for malfunction or electric shock may occur.

●Adjust airflow and direction properly
When the unit is running, adjust up and down adjusting plate
by wireless remote control can adjust vertical direction of
air, hold the adjust plate that control left and rignt direction

can adjust horizontal flow direction of air.

Left and right adjust plate

●Don't blow pets or plants directly for it is not
good for them.

Power hose of this unit adopts X type connection, don't
cut off or damage it and signal control wire. If power
hose or signal wire is damaged, please have them

changed by trained maintainer.

Up and down adjust plate

The unit allow voltage fluctuation of ２３０±１０％Ｖ，

too low of voltage may increase libration of

compressor that cause damage on cool system.

50Hz~230V

This unit cannot be used to dry clothes or refrigerate
and store foods etc..

４

Structure Principle and Usage

Specificate Model and Technical Data

50Hz

230V～

T1

IP×4

Indoor：101.5×29.0×15

Outdoor：84.8×54.0×32.0

2000 2500 3500

Cooling and Heating Cooling and Heating Cooling and Heating

ASH-07AF ASH-09AF ASH-12AF

Function

Model

Cooling Capacity（W）

2300 2700 3700

Heating Capacity（W）

4/4 4/4 6.26/6.26

450 450 500

/h）

３

920/920 920/920 1440/1440

Rated Voltage

Rated Frequency

Air Flow（m

Cooling/Heating Rated Power (W)

Cooling/Heating Rated Currency (A)

38/52 38/53 40/54

R410A 1. 2kg R410A 1.35kg R410A 1.4kg

Name of Refrigerant and Charge Amount

Noise (Indoor/Outdoor) dB（A）

Climate Type

Water-proof Level

Electric Shork Proof Protect Type I Weight (Indoor/Outdoor) (kg)

11/32 11/32 11/36

（W ×H ×D）（cm）

All above are tested according to standard ＧＢ／Ｔ７７２５－１９９６, cooling capacity, heating capacity and noise etc. are tested before leaving factory

Outline Diameter (Indoor/Outdoor)

If the data are changed, please refer the one offered on nameplate.

Remote control operation procedure

Note:

Be sure that there are no obstructions between receiver and remote controller.
The remote control signal can be received at the distance of up to about 10m.
Don’t drop or throw the remote control.
Don’t let any liquid in the remote controller and put the remote controller di-

rectly under the sunlight or any place where is very hot.

SWING button

REMOTE CONTROL OPERATION PROCEDURE

When it is pressed, the louvers
start to rotate automatically and
stop when repressed.

Name and Function-Remote control

FAN button

Press this button to change
the fan speed of:

TEMP. button

SET TEMP. increases 1
pressing button once,and decreases
1

by pressing button once.
At COOL mode operation, SET
TEMP. can be selected from 16
30

.
At DRY mode oper ation, SET TEMP.
can be selected from 16
At HEAT mode operation, SET
TEMP. can be selected from 16
30

.

MODE button
press this button to change the
operation mode in order of:

AUTO

by

to

to 30 .

to

“ ” COOL mode
“ ” DRY mode
“ ” FAN mode
“ ” HEAT mode

ON/OFF button (1/0 is
used in some models)
Press this button to turn on
or turn off the unit.

3

Name and Function-Remote control. (Remove the cover)

Note: This type of remote controller is a kind of new controller.

some buttons of the controller which are not available to this Air condi-

tioner will not be described below.
Operate on unmentioned buttons would not impact on the normal use.

Liquid crystal displayer It
shows all set contents.

SLEEP button
Press this button to set
SLEEP operation. And stop
when repressed.

1/0 is used in some
models

TIMER ON button
At stopping, press TIMER
ON button, set ON TIME in
range of 0 to 24 hour at the
interval of 0.5h to start the
unit automatically.

0 24h

Timer

cancellation

TIMER OFF button
At operating, press TIMER
OFF button, set OFF TIME
in range of 0 to 24 hour to
stop the unit automatically.

0 24h

Timer

cancellation

REMOTE CONTROL OPERATION PROCEDURE

4

REMOTE CONTROL OPERATION PROCEDURE

3.Press SWING button,

COOL mode operation procedure

According to difference between room temp. and set temp., microcomputer can control cooling on or

not.

If room temp. is higher than set temp., compressor runs at COOL mode.

If room temp. is lower than set temp., compressor stops and only indoor fan motor runs.

SET TEMP. should be in range of 16

the louvers start to ro­tate automatically, and
stop when repressed.

to 30

4.Press FAN button, set

fan speed.

5.Press TEMP. but-

ton, set suitable SET
TEMP.

2.Press MODE button,

set operation
mode.

1.Plug in, press ON/OFF button
(1/0 is used in some models),then
air conditioner is turned on.

5

HEAT mode operation procedure

If room temp. is lower than set temp., compressor runs at HEAT mode;
If room temp. is higher than set temp., compressor and outdoor fan motor stop, only indoor fan motor
runs, louver motor makes the louvers horizontal.
SET TEMP. should be in range of 16

to 30

3.Press SWING button, the

louvers start to rotate
automatically, and stop
when repress it.

4.Press FAN button, set

fan speed.

5.Press TEMP. but-

ton, set suitable
SET TEMP.

REMOTE CONTROL OPERATION PROCEDURE

1.Plug in, press ON/OFF button
(1/0 is used in some models),
then air conditioner is turned on.

2.Press MODE button,

set operation
mode.

6

DRY mode operation procedure

If room temp. is lower than set temp., compr essor ,outdoor and indoor fan motor stop. If r oom temp. is

REMOTE CONTROL OPERATION PROCEDURE

between

2 of set temp., Air conditioner is drying.If room temp. is higher than set temp., it’s at
COOL mode.
SET TEMP. should be in range of 16

3.Press SWING button,

the louvers start to ro­tate automatically, and
stop when repress it.

to 30

4.Press TEMP.button,set
suitable SET TEMP.

2.Press MODE button,set
operation mode.
Air speed couldn’t be
changed after the “ ”
being set.

7

1.Plug in,press ON/OFF button
(1/0 is used in some models),then
air conditioner is turned on.

AUTO mode operation procedure

Under Auto mode operation, standard SET TEMP. is 25 for COOL mode and 20 for H E AT
mode.

1.Plug in,Press ON/OFF but­ton (1/0 is used in some
models), then air conditioner
is turned on.

2.According to room temp.,micro­computer can automatically set

operation mode,so

as for best effect.

REMOTE CONTROL OPERATION PROCEDURE

8

REMOTE CONTROL OPERATION PROCEDURE

TIMER mode operation procedure

TIMER ON button

At stopping, press TIMER
ON button, set ON TIME in
range of 0 to 24 hour to start
the unit automatically.

1/0 is used in some models

TIMER OFF button

At operating, press TIMER
OFF button, set OFF TIME
in range of 0 to 24 hour to
stop the unit automatically.

0 24h

Timer

cancellation

0 24h

Timer

cancellation

9

SLEEP mode operation procedure

As the unit is cooling or drying, if SLEEP operation is set, SET TEMP. would increase 1 in 1 hour
and 2

in 2 hours.
As the unit is heating , if SLEEP operation is set, SET TEMP. would decrease 1
2 hours.

4.Press FAN button, set

fan speed.

3.Press SWING button, the

louvers start to rotate
automatically, and stop
when repress.

6.SLEEP button
Press it to set SLEEP

operation.

in 1 hour and 2 in

5.Press TEMP. but-

ton, set suitable
SET TEMP.

2.Press MODE button,

set or op­eration mode.

REMOTE CONTROL OPERATION PROCEDURE

1.Plug in, press ON/OFF button
(1/0 is used in some models),then
air conditioner is turned on.

10

1.Remove the cover from the back
of the remote control.

2.Insert the two batteries ( Two AAA
dry - cell batteries ) and press but­ton “ACL”.

3.Re - attach the cover.

REMOTE CONTROL OPERATION PROCEDURE

NOTE:

How to insert batteries

Don’t confuse the new
and worn or different
types of batteries.
Remove batteries when
the remote controller is
not in use for a long
time.
The remote control sig­nal can be received at
the distance of up to
about 10m.
The lifetime of the bat­teries is about one year.
The remote controller
should be placed about
1m or more away from
the TV. or any other

2. Insert the AAA batteries.

1.Remove the cover.

3.Re - attach the cover.

11

electric appliances.
Bad batteries are for­bidden.

Install Part

◆　　Install Note Items

Select of install location

Indoor unit

１．The air inlet and outlet vent should be far away from obstruction to ensure the air

is blowed to the entire room.

2.Select where is easy to drain condensate or connect with outdoor unit.

3.Far away from heat resource, steam and flammable gas.

4.Select where can stand weight of indoor unit without increasing running noise and librations.

5.Ensure there is enough space for maintenance, and indoor unit should be at lest 2m above floor.

6.Place the unit to where is at lest 1m away from TV, Hi-fi and other appliances.

7.Select where air filter can be taken out easily.

８．Ensure the install of indoor unit meets requirements on Install Dimension Diagram.

Outdoor unit

１．Select place where noise and airflow produced when exharsting will not annoy neighbours.

２．Ensure well ventilation of outdoor unit.

３．There is no obstruction that may impact air in and out nears outdoor unit.

４．Install place should be able to stand weight and libration of outdoor unit and let the

outdoor unit run safely.

５．Select place where there is no leakage of flammable or corrosible gas.

６．Ensure the install of outdoor unit meets requirements on Install Dimension Diagram.

９

Ｉｎｓｔａｌｌ　Ｐａｒｔ

Ｗｉｒｅ　ｃｏｌｌｏｃａｔｉｏｎ

１．Wire should be connected according to local wiring regulation.
２．Power supply must adopt rated voltage and special circuit for air conditioner,

and size of the power wire should be big enough.

３．Please don't pull power wire forcibly.

４．Earthing should be reliable, and should be connected on special earthing settings on building,

and have them connected by professional personnel. Creepage protect switch and air switch

with enough capacitance must be set in rated circuitry (Refer to the following form). Air switch
should maintain magnetic and heat drop-out functions to ensure protect when curcuit short or overload occurs.

Ｍｏｄｅｌ

ASH-07AF
ASH-09AF
ASH-12AF

Ｃａｐａｃｉｔａｎｃｅ

ｏｆ　ａｉｒ　ｓｗｉｔｃｈ

１０Ａ
１０Ａ

１５Ａ

Ｅａｒｔｈ　ｗｉｒｅ

ｍｉｎ　ｓｅｃｔｉｏｎ

２

１．０ｍｍ

２

１．０ｍｍ

２

１．５ｍｍ

Ｐｏｗｅｒ　ｗｉｒｅ　ｏｆ　ｕｎｉｔ

ｍｉｎ．　ｓｅｃｔｉｏｎ

２

１．０ｍｍ

２

１．０ｍｍ

２

１．５ｍｍ

Ｅａｒｔｈｉｎｇ　ｒｅｑｕｉｒｅｍｅｎｔｓ

１．Air conditioner is type I appliance, please do conduct reliable earthing measure.

２．The yellow-green wire in the unit is earth wire, don't use it for other purpose or cut it.

Don't fix it by self tapping screw, or electric shock may occur.

３．User power supply should offer reliable earth terminal. Don't connect earth wire to

following place:

①Ｗａｔｅｒ　ｐｉｐｅ　②　Ｇａｓ　ｐｉｐｅ　③Ｂｌｏｗｉｎｇ　ｐｉｐｅ④Ｗｈｅｒｅ　ｐｒｏｆｅｓｓｉｏｎａｌ　ｐｅｒｓｏｎｎｅｌ　ｃｏｎｓｉｄｅｒｓ　ｉｔ　ｕｎｒｅｌｉａｂｌｅ

１０

Ｉｎｓｔａｌｌ　Ｐａｒｔ

Ｉｎｓｔａｌｌ　Ｄｉｍｅｎｓｉｏｎ　Ｄｉａｇｒａｍ　

Distance between unit and wall

Distance between
unit and ceiling

Distance between unit and wall

Air out side

Distance between unit and floor

Ｉｍｐｏｒｔａｎｔ　Ａｄｖａｎｃｅ

★

The installation must be done by professional personnel with reliability
according to this manual.

★

Contact service center before installation to avoid the malfunction due
to unprofessional installation.

★

When moving the units, you must be guided by professional personnel.

Distance between
unit and slider

Distance between unit and wall

Air in side

Distance between unit and wall

Air out side

１１

Ｉｎｓｔａｌｌ　Ｐａｒｔ

◆　　Ｉｎｓｔａｌｌ　ｔｈｅ　ｉｎｄｏｏｒ　ｕｎｉｔ

☆　Ｉｎｓｔａｌｌ　ｔｈｅ　ｒｅａｒ　ｐａｎｅｌ

1.Always mount the rear panel horizon­tally.As the water drainage pipe at

the left,this side should not be too
high when adjusting the rear panel.it

had better to adjust this side a little lower.

2.Fix the rear panel on the selected location.

3.Be sure that the rear panel has been fixed firmly enough to withstand
the weight of an adult of 60kg,furthermore,the weight should be

evenly shared each screw.

☆　

Install the piping hole

１．

Make the piping hole(¦Õ50) in the wall at a slight downward slant t

the outdoor side.

２．

Insert the piping-hole sleeve into the hole to prevent the connection
piping andwiring from being damaged when passing through the hole.

☆　

Install the drain hose

1.For well draining, the drain hose shoule be placed
at a downward slant.

2.Do not wrench or bend the drain hose or flood its

end by water.

3.When the long drainage hose passing through indoor

should wrap the insulation materials.

☆　

Install the connection pipes

Connect the connection pipes with the relevant union pipes of the indoor unit and

tighten the flare nut of the connection pipes (Shown in P19"Install the connection

pipes")

Ｆｉｇ．１

Ｗｒｅｎｃｈｅｄ

Ｆｉｇ．２

o　

Ｂｅｎｔ

Ｄｏｎ＇ｔ　ｓｏａｋ　ｉｎ　ｔｈｅ　ｗａｔｅｒ

Ｎｏｔｅ：

▲

Connect the connection pipes with the indoor unit
firstly and the outdoor unit secondly.

▲

Be careful in bending the connection pipes or you

will damage the pipe.

▲

If the tightening torque is too great in tightening

the flare nuts, leakage will happen.

☆　

Electric wiring

ｃｏｎｎｅｃｔｉｏｎ　ｐｏｗｅｒ　ｉｎｓｉｄｅ　ａｎｄ　

　ｏｕｔｓｉｄｅ　ｔｈｅ　ｕｎｉｔ

1.Open the panel upwards.

2.Disassembly the fixing bolts of connection cover , shown in the Fig. at right side.

3.power connecting wire cross through down to up from the bottom of case.

１２

ｃｏｖｅｒ　ｏｆ　ｃｏｎｎｅｃｔｉｏｎ

Install Part

4.Connect blue wire in power connect wire onto "N(1)" terminal, brown wire onto "2" terminal,

yellow-green wire (i.e. earth wire) onto " " terminal (as shown in fig.3); and press the

power connect wire by wire groove that in front of line bank that installed in electric box.

5.To heat pump type unit, signal control wire connect with indoor unit through connector
as (shown in fig.3), and tighten the control wire by wire clamp on bottom of case.

6.Install the cover plate on where it was and tighten screws.

7.Cover panel.

Signal control wire (only for heat pump units)

Line bank

Connector

Wire

blue

brown

yellow-green

gloove

Power connect

Wire clamp

wire

Ｆｉｇ．３

☆Install Indoor Unit

１．Please refer to the fig. (a) and (b) for routing piping type of indoor unit. When routing the

piping (wiring) from the left or right side, cut off the tailings of the pipe left from chassis

of main unit (as shown in fig.4(c)):

(1)Cut off tailings 1 when only power cord is routed;

（２）Cut off tailings 1 and 2 when connection pipe and power cord are routed.

１３

Ｉｎｓｔａｌｌ　Ｐａｒｔ

Methods ①、②、③ are recommended piping ways.

２．After wrapped pipe and wire, pull them though the pipe hole (as shown in fig.5).
３．Hang the mounting slot behind indoor unit on the pothook of the rear panel and move

it to check if it is firm enough (as shown in fig.6).

４．Ensure the install height of indoor unit is 2m or higher.

①Right pipe

②Rear right pipe

（ａ）

Wrapping strap

Coonection pipe

Power connect wire

Tailings ２

Tailings １

Fig.5

Fig.4

（ｃ）

Fig.6

◆　　Ｉｎｓｔａｌｌ　ｏｆ　Ｏｕｔｄｏｏｒ　Ｕｎｉｔ

（ｂ）

Drainage hose

④Left pipe

③Rear left pipe

Signal control wire

☆　Ｉｎｓｔａｌｌ　ｃｏｎｎｅｃｔｉｏｎ　ｐｉｐｅ

１．Aligh the flare of connection pipe to the joint flare of relative valve.
２．Tighten the nuts on connection pipe forcibly then tighten ti by spanner as shown in fig.7.

Note: Too great of torque would damage nuts.

１４

Ｉｎｓｔａｌｌ　Ｐａｒｔ

Ｔｉｇｈｔｅｎｉｎｇ　ｔｏｒｑｕｅ　ｔａｂｌｅ

Ｈｅｘ　ｎｕｔ

Ф６

９．５

１２

Ｔｉｇｈｔｅｎｉｎｇ　ｔｏｒｑｕｅ　ｔａｂｌｅ（Ｎ·ｍ）

１５～２０

３１～３５

５０～５５

☆　Ｅｌｅｃｔｒｉｃ　ｗｉｒｉｎｇ　ｃｏｎｎｅｃｔｉｏｎ

Nut of connection pipe

Ｔｏｒｑｕｅ　ｗｒｅｎｃｈ

Ｓｐａｎｎｅｒ

Ｊｏｉｎｔ

Ｆｉｇ．７

１．Take off handle on right side plate of outdoor unit (1 bolt).
２．Take off clamp, then connect and fix the power connect wire to wiring terminal

board.Wiring allocation should be in accordance with that of indoor unit.

３．Fix power connect wire by clamp, to cooling and heating unit, fix signal control wire too,

then connect the corresponding connector well.

４．Ensure that the wiring is done well.
５．Install handle (tightened by 1 bolt).

ＮＯＴＥ：

●Wrong wiring connection will lead

to electric malfunction.

●

The lead between the joint and the fixed should

be a little free when fixing it with wire clamp.

１５

Signal control wire

Only for cooling
and heating unit

Ｈａｎｄｌｅ

Blue

Wire clamp

Yellow-green

Brown

Power connect wire

Ｉｎｓｔａｌｌ　Ｐａｒｔ

☆　Ａｉｒ　ｐｕｒｇｉｎｇ　ａｎｄ　ｌｅａｋａｇｅ　ｔｅｓｔ

１．Ｒｅｍｏｖｅ　ｔｈｅ　ｎｕｔｓ　ｃａｐ　ｆｒｏｍ　ｔｈｅ　ｃｕｔ－ｏｆｆ　ｖａｌｖｅｓ

ｏｆ　ｔｈｅ　ｏｕｔｄｏｏｒ　ｕｎｉｔ．
２．Ａｉｍ　ａｔ　ｔｈｅ　ｃｅｎｔｅｒ　ｏｆ　ｔｈｅ　ｔｕｂｉｎｇ，　ｓｃｒｅｗ　ｔｈｅ

ｃｏｎｅ－ｓｈａｐｅｄ　ｎｕｔｓ　ｂｙ　ｈａｎｄ．

３．Ｔｉｇｈｔｅｎｉｎｇ　ｔｈｅ　ｃｏｎｅ－ｓｈａｐｅｄ　ｎｕｔｓ　ｗｉｔｈ　ｗｒｅｎｃｈ．
４．Ｒｅｍｏｖｅ　ｔｈｅ　ｖａｌｖｅ　ｃａｐｓ　ｏｆ　ｔｈｅ　ｇａｓ　ｖａｌｖｅ　ａｎｄ

ｌｉｑｕｉｄ　ｖａｌｖｅ　ａｎｄ　ｔｈｅ　ｓｅｒｖｉｃｅ　ｐｏｒｔ　ｎｕｔ．

５．Ｌｏｏｓｅｎ　ｔｈｅ　ｖａｌｖｅ　ｓｒｅｍ　ｏｆ　ｔｈｅ　ｌｉｑｕｉｄ　ｖａｌｖｅ

ｗｉｔｈ　ａ　ｈｅｘ　ｗｒｅｎｃｈ．ｐｕｓｈ　ｔｈｅ　ｃｈｅｃｋ　ｖａｌｖｅ　ｃｏｒｅ
ｏｆ　ｔｈｅ　ｇａｓ　ｖａｌｖｅ　ｔｏ　ｄｉｓｃｈａｒｇｅ　ａｉｒ　．

６．Ａｆｔｅｒ　１５　ｓｅｃｏｎｄｓ，　ｓｔｏｐ　ｐｕｓｈｉｎｇ　ｔｈｅ　ｖａｌｖｅ

ｃｏｒｅ　ａｓ　ｓｏｏｎ　ａｓ　ｔｈｅ　ｒｅｆｒｉｇｅｒａｎｔ　ｓｔａｒｔｓ　ｔｏ　ｂｅ

ｄｉｓｃｈａｒｇｅｄ，　ａｎｄ　ｒｅｉｎｓｔａｌｌ　ｔｈｅ　ｓｅｒｖｉｃｅ　ｐｏｒｔ　ｎｕｔ．

７．Ｏｐｅｎ　ｔｈｅ　ｌｉｑｕｉｄ　ｖａｌｖｅ　ｃａｐｓ　ａｎｄ　ｇａｓ　ｖａｌｖｅ　

ｅｎｔｉｒｅｌｙ　（ｓｈｏｗｎ　ｉｎ　Ｆｉｇ．８）

８．Ｔｉｇｈｔｅｎ　ｔｈｅ　ｖａｌｖｅ　ｃａｐｓ　ａｎｄ　ｔｅｓｔ　ｌｅａｋａｇｅ　ａｔ

ａｌｌ　ｊｏｉｎｔｓ　ｏｆ　ｔｈｅ　ｐｉｐｉｎｇ（ｂｏｔｈ　ｉｎｄｏｏｒ　ａｎｄ

ｏｕｔｄｏｏｒ）ｂｙ　ｌｉｑｕｉｄ　ｓｏａｐ　ｏｒ　ｌｅａｋ　ｄｅｔｅｃｔｏｒ．

９．Ｉｆ　ｐｏｓｓｉｂｌｅ，　ｄｉｓｃｈａｒｇｅ　ａｉｒ　ｆｒｏｍ　ｖａｌｖｅ　ｃｏｒｅ

ｗｉｔｈ　ａ　ｖａｃｕｕｍ　ｐｕｍｐ．（ｓｈｏｗｎ　ｉｎ　ＦＩｇ．９）

Ｇａｓ　ｐｉｐｅ

Ｌｉｑｕｉｄ

ｐｉｐｅ

Ｌｉｑｕｉｄ　ｐｉｐｅ

Ｓｃｒｅｗｄｒｉｖｅｒ

Ｆｌｕｒｉｎｅ　ｃｈａｒｇｉｎｇ
　ｎｕｚｚｌｅ

Ｇａｓ　ｖａｌｖｅ

Ｌｉｑｕｉｄ　ｖａｌｖｅ

Ｈｅｘ　ｗｒｅｎｃｈ

Ｆｉｇ．８

Ｖａｃｕｕｍ　ｖａｌｖｅ

Ｖａｌｖｅ　ｃａｐ

Ｖａｃｕｕｍ　ｐｕｍｐ

Ｇａｓ　ｐｉｐｅ

Ｆｉｇ．９

☆　Ｏｕｔｄｏｏｒ　ｃｏｎｄｅｎｓａｔｉｏｎ　ｄｒａｉｎａｇｅ

　　　（Ｈｅａｔ　ｐｕｍｐ　ｔｙｐｅ　ｏｎｌｙ）

Ｗｈｅｎ　ｔｈｅ　ｕｎｉｔ　ｉｓ　ｈｅａｔｉｎｇ　ｏｒ　ｄｅｆｒｏｓｔｉｎｇ，　ｔｈｅ
ｃｏｎｄｅｎｓｉｎｇ　ｗａｔｅｒ　ａｎｄ　ｄｅｆｒｏｓｔｉｎｇ　ｗａｔｅｒ　ｆｏｒｍｅｄ
ｉｎ　ｔｈｅ　ｏｕｔｄｏｏｒ　ｕｎｉｔ　ｃａｎ　ｂｅ　ｄｒａｉｎｅｄ　ｏｕｔ　ｒｅｌｉａｂｌｙ

ｔｈｒｏｕｇｈ　ｔｈｅ　ｄｒａｉｎ　ｈｏｓｅ．

Ｉｎｓｔａｌｌａｔｉｏｎ：　ｉｎｓｔａｌｌ　ｔｈｅ　ｏｕｔｄｏｏｒ　ｄｒａｉｎ　ｔｉｅ－ｉｎ　
ｉｎ　ｔｈｅ　　２５　ｈｏｌｅ　ｏｎ　ｔｈｅ　ｂａｓｅ　ｐｌａｔｅ　ａｓ　ｓｈｏｗｎ

Ø

ｉｎ　Ｆｉｇ．１０，　ａｎｄ　ｊｏｉｎｔ　ｔｈｅ　ｄｒａｉｎ　ｈｏｓｅ　ｔｏ　ｔｈｅ　ｔｉｅ－ｉｎ，
ｓｏ　ｔｈａｔ　ｔｈｅ　ｗａｓｔｅｗａｔｅｒ　ｆｏｒｍｅｄ　ｉｎ　ｔｈｅ　ｏｕｔｄｏｏｒ

ｕｎｉｔ　ｃａｎ　ｂｅ　ｄｒａｉｎｅｄ　ｏｕｔ　ｔｏ　ａ　ｐｒｏｐｅｒ　ｐｌａｃｅ．

１６

Ｂａｓｅ　ｐｌａｔｅ　ｏｆ

ｏｕｔｄｏｏｒ　ｕｎｉｔ

Ｏｕｔｄｏｏｒ　ｄｒａｉｎ　ｔｉｅ－ｉｎ

Ｆｉｇ．１０

Ｉｎｓｔａｌｌ　Ｐａｒｔ

◆　Ｔｒｉａｌ　ｒｕｎ　ａｎｄ　ｃｈｅｃｋ　ｉｔｅｍｓ　ａｆｔｅｒ　ｉｎｓｔａｌｌａｔｉｏｎ

☆　Ｔｒｉａｌ　Ｒｕｎ

１．　Preparation for trial run

（１）　Don't turn on power supply if entire

installations are not completed.

（２）　Connect of control circuit should be correct

all wire connect should be firm.

（３）　Cut-off valves of both thick and thin pipes should be turned on.
（４）　All scattered components, especially metal scrap thrum etc., should be cleared from unit.

２．　Ｔｒｉａｌ　ｒｕｎｎｉｎｇ　ｍｏｔｈｏｄ

（１）　

Press ON/OFF on wireless remote control after connecting to power supply, unit begins running.

（２）　

Press MODE to select run mode of COOL, HEAT and SWING etc. to check if it can run normally.

（３）　When wireless remote control is losed, operation unit by following mode:
（ａ）　When unit is halt, press the ON/OFF button, then unit begins running in AUTO micro-

computer select COOL, DRY, HEAT or FAN automatically according to indoor temp.

to make comfort effect. Repress ON/OFF to stop the unit from running.

（ｂ）　When unit is running, press ON/OFF to stop unit from running.

Heating indicator

Cooling indicator

ON/OFF button

Running indicator

☆　Ｃｈｅｃｋ　ａｆｔｅｒ　ｉｎｓｔａｌｌａｔｉｏｎ

Ｉｔｅｍｓ　ｔｏ　ｂｅ　ｃｈｅｃｋｅｄ

Is the installation firm enough？
Is leakage test done？
Is heat insulation sufficient？

Is drainage smooth？
Is the power voltage the same with that in

product nameplate？
Is the install of circuit and pipeline correct？

Is the unit earthed safely？
Is model of wire fits that of regulation？

Is both the air inlet or outlet vent of indoor
and outdoor unit blocked？

Is length of refrigerant pipe and charge amount recorded

　　　　　　Creepage may occur

Ｐｏｓｓｉｂｌｅ　ｍａｌｆｕｎｃｔｉｏｎ

Unit may drop, shake or emit noise

It may cause insufficient of cooling (heating) capacity

Condensation or water drop may occur

Condensation or water drop may occur

Malfunction or burn out of parts may occur

Malfunction or burn out of parts may occur

Malfunction or burn out of parts may occur

Insufficient of cooling (heating)
capacity may occur.

？

Charge amount of refigerant is hard to handle.

１７

Ｒｅｐａｉｒ　ａｎｄ　Ｍａｉｎｔｅｎａｎｃｅ

Ｒｅｐａｉｒ　ａｎｄ　Ｍａｉｎｔｅｎａｎｃｅ

◆

Ｗａｒｎｉｎｇ

▲Stop the unit and pull out the plug before cleaning the unit,or electic shock will be happened.
▲Don't get wet the unit,for it will cause the electric shock,make sure don't wash

the unit by water.

▲The volatile liquid,such as thinner or gas will damage the face of unit. (only using

the soft cloth and wet cloth with neutral cleaning fluid to clean the body of unit)

Ｕｎｐｉｃｋ　ａｎｄ　ｗａｓｈ　ｔｈｅ　ｆｉｌｔｅｒ

１．Ｕｐｌｉｆｔ　ｔｈｅ　ｐａｎｅｌ　ｕｐｗａｒｄｓ　ｂｙ　ｈａｎｄ　ａｃｃｏｒｄｉｎｇ　ｔｏ
　　ｔｈｅ　ｄｉｒｅｃｔｉｏｎ　ｏｆ　ａｒｒｏｗｈｅａｄ．

２．Ｐｕｔ　ｄｏｗｎ　ｔｈｅ　ｐａｎｅｌ　ａｃｃｏｒｄｉｎｇ　ｔｏ　ｄｉｒｅｃｔｉｏｎ　ｏｆ

　　ａｒｒｏｗｈｅａｄ．

３．Ｕｐｌｉｆｔ　ｔｈｅ　ｐａｎｅｌ　ａ　ｌｉｔｔｌｅ　ｂｉｔ　ａｃｃｏｒｄｉｎｇ　ｔｏ　ｔｈｅ

ｄｉｒｅｃｔｉｏｎ　ｏｆ　ａｒｒｏｗ　１，ｔｈｅｎ　ｔａｋｅ　ｏｕｔ　ｔｈｅ　ｆｉｌｔｅｒ
ａｃｃｏｒｄｉｎｇ　ｔｏ　ａｒｒｏｗ　２．ｃｌｅａｎ　ｔｈｅ　ｆｉｌｔｅｒ　ｂｙ　ｃｌｅａｎｅｒ
ｏｒ　ｗａｔｅｒ，ｗｈｅｎ　ｔｈｅ　ｆｉｌｔｅｒ　ｉｓ　ｄｉｒｔｙ（ｏｉｌ），ｉｔ　ｃａｎ　ｂｅ
ｗａｓｈｅｄ　ｂｙ　ｗａｒｍ　ｗａｔｅｒ（ｂｅｌｏｗ　４５℃）　ｄｉｓｓｏｌｖｉｎｇ　
ｗｉｔｈ　ｎｅｕｔｒａｌ　ｃｌｅａｎｉｎｇ　ｆｌｕｉｄ，ｔｈｅｎ　ｄｒｙ　ｉｔ　ｏｎ
ｔｈｅ　ｓｈａｄｙ　ａｎｄ　ｃｏｏｌ　ｐｌａｃｅ．

Ｉｎｓｔａｌｌａｔｉｏｎ　ｏｆ　ｆｉｌｔｅｒ

１．Ｕｐｌｉｆｔ　ｔｈｅ　ｐａｎｅｌ　ａ　ｌｉｔｔｌｅ　ｂｉｔ　ｆｒｏｍ　ｔｈｅ　ｄｉｒｅｃ－

ｔｉｏｎ　ｏｆ　ａｒｒｏｗｈｅａｄ　１，ｔｈｅｎ　ｉｎｓｅｒｔ　ｔｈｅ　ｆｉｌｔｅｒ　
ｂｅｌｏｗ　ｔｈｅ　ｐａｎｅｌ　ａｃｃｏｒｄｉｎｇ　ｔｏ　ａｒｒｏｗｈｅａｄ　２．

２．Ｕｐｌｉｆｔ　ｔｈｅ　ｐａｎｅｌ　ａｃｃｏｒｄｉｎｇ　ｔｏ　ｔｈｅ　ｄｉｒｅｃｔｉｏｎ　

　ｏｆ　ａｒｒｏｗｈｅａｄ　ｔｏ　ｔｈｅ　ｌｏｃａｔｉｏｎ　ｓｈｏｗｎ　ａｓ　Ｆｉｇ．

３．Ｉｎｓｅｒｔ　ｔｈｅ　ｃｌａｍｐ　Ａ、Ｂ、Ｃ　ｂａｃｋ　ｔｏ　ｔｈｒｅｅ　ｔｈｅ　

ｒｏｔａｔｉｎｇ　ｓｈａｆｔ．ａｎｄ　ｃｏｖｅｒ　ｔｈｅ　ｐａｎｅｌ．

１８

Ｒｅｐａｉｒ　ａｎｄ　Ｍａｉｎｔｅｎａｎｃｅ

Ｃｈｅｃｋ　ｂｅｆｏｒｅ　ｕｓｅ　

１．　Ｂｅ　ｓｕｒｅ　ｔｈａｔ　ｎｏｔｈｉｎｇ　ｏｂｓｔｒｕｃｔｓ　ｔｈｅ

ｔｈｅ　ａｉｒ　ｏｕｔｌｅｔ　ａｎｄ　ｉｎｔａｋｅ　ｖｅｎｔｓ．

２．　Ｃｈｅｃｋ　ｔｈａｔ　ｗｈｅｔｈｅｒ　ｇｒｏｕｎｄ　ｗｉｒｅ　ｉｓ　

ｐｒｏｐｅｒｌｙ　ｃｏｎｎｅｃｔｅｄ　ｏｒ　ｎｏｔ．
３．Ｃｈｅｃｋ　ｔｈａｔ　ｗｈｅｔｈｅｒ　ｔｈｅ　ｂａｔｔｅｒｉｅｓ　ｏｆ
　　　ａｉｒ　ｃｏｎｎｅｃｔｉｏｎｅｒ　ａｒｅ　ｃｈａｎｇｅｄ　ｏｒ　ｎｏｔ

４．Ｃｈｅｃｋ　ｔｈａｔ　ｗｈｅｔｈｅｒ　ｔｈｅ　ｉｎｓｔａｌｌａｔｉｏｎ　

ｓｔａｎｄ　ｏｆ　ｔｈｅ　ｏｕｔｄｏｏｒ　ｕｎｉｔ　ｉｓ　ｄａｍａｇｅｄ
　ｏｒ　ｎｏｔ．ｉｆ　ｄａｍａｇｅｄ，　ｐｌｅａｓｅ　ｃｏｎｔａｃｔ　
　ｔｈｅ　ｄｅａｌｅｒ．

Ｍａｉｎｔｅｎａｎｃｅ　ａｆｔｅｒ　ｕｓｅ　

１．　Ｃｌｅａｎ　ｆｉｌｔｅｒｓ　ａｎｄ　ｏｔｈｅｒ　ｐａｒｔｓ．
２．　Ｔｕｒｎ　ｍａｉｎ　ｐｏｗｅｒ　ｏｆｆ．
３．　Ｃｌｅａｒ　ｄｕｓｔ　ｆｒｏｍ　ｔｈｅ　ｏｕｔｄｏｏｒ　ｕｎｉｔ．
４．　Ｒｅｐａｉｎｔ　ｔｈｅ　ｒｕｂｉｇｉｎｏｕｓ　ｐｌａｃｅ　ｏｎ　ｔｈｅ

ｏｕｔｄｏｏｒ　ｕｎｉｔ　ｔｏ　ｐｒｅｖｅｎｔ　ｉｔ　ｆｒｏｍ　

　　　ｓｐｒｅａｄｉｎｇ．

◆

Ｗｈｅｎ　ｔｈｅ　ｕｎｉｔ　ｃａｎｎｏｔ　ｒｕｎ　ｎｏｒｍａｌｌｙ

Ｗａｒｎｉｎｇ：Ｄｏｎ＇ｔ　ａｔｔｅｍｐｔ　ｔｏ　ｒｅｐａｉｒ　ｔｈｅ　ａｉｒ　ｃｏｎｄｏｔｉｏｎｅｒ　ｂｙ　ｙｏｕｒｓｅｌｆ，　ｉｔ　ｃａｎ　　

ｃａｕｓｅ　ａｎ　ｅｌｅｃｔｒｉｃ　ｓｈｏｃｋ　ｏｒ　ｆｉｒｅ．　ｐｌｅａｓｅ　ｃｈｅｃｋ　ｔｈｅ　ｆｏｌｌｏｗｉｎｇ　ｉｔｅｍｓ　
ｂｅｆｏｒｅ　ａｓｋｉｎｇ　ｆｏｒ　ｒｅｐａｉｒ，ｉｔ　ｃａｎ　ｓａｖｅ　ｙｏｕｒ　ｔｉｍｅ　ａｎｄ　ｍｏｎｅｙ．

Ｐｈｅｎｏｍｅｎｏｎ

Ｃｏｍｐｒｅｓｓｏｒ　ｄｏ　ｎｏｔ　ｏｐｅｒａｔｅ　ｗｈｅｎ
ｔｈｅ　ａｉｒ　ｃｏｎｄｉｔｏｎｅｒ　ｉｓ　ｒｅｓｔａｒｔｅｄ．

waiting

Ｔｈｅｒｅ＇ｓ　ｕｎｕｓｕａｌ　ｓｍｅｌｌ　ｂｌｏｗｉｎｇ　ｆｒｏｍ　ｔｈｅ
ｏｕｔｌｅｔ　ａｆｔｅｒ　ｏｐｅｒａｔｉｏｎ　ｉｓ　ｓｔａｒｔｅｄ．

　　　　　　　　　　　Ｔｒｏｕｂｌｅ　ｓｈｏｏｔｉｎｇ

Ｏｎｃｅ　ｔｈｅ　ａｉｒ　ｃｏｎｄｉｔｉｏｎｅｒ　ｉｓ　ｓｔｏｐｐｅｄ，
ｉｔ　ｗｉｌｌ　ｎｏｔ　ｏｐｅｒａｔｅ　ｉｎ　ａｐｐｒｏｘｉｍａｔｅｌｙ

ｔｏ　ｐｒｏｔｅｃｔ　ｉｔｓｅｌｆ．

Ｔｈｉｓ　ｉｓ　ｃａｕｓｅｄ　ｂｙ　ｔｈｅ　ｏｄｏｒｓ　ｗｈｉｃｈ　ｇｉｖｅ
ｏｆｆ　ｆｒｏｍ　ｆｕｒｎｉｔｕｒｅ　ａｎｄ　ｃｉｇａｒｅｔｔｅ

ｄｕｒｉｎｇ　ｔｈｅ　ＡＣ　ａｄｊｕｓｔ　ｔｈｅ　ａｉｒ．

１９

Ｒｅｐａｉｒ　ａｎｄ　Ｍａｉｎｔｅｎａｎｃｅ

Ｐｈｅｎｏｍｅｎｏｎ

Ｓｏｕｎｄ　ｏｆ　ｗａｔｅｒ　ｆｌｏｗ　ｃａｎ　ｂｅ　ｈｅａｒｄ　Ｔｈｉｓ　ｉｓ　ｃａｕｓｅｄ　ｂｙ　ｔｈｅ　ｒｅｆｒｉｇｅｒａｎｔ　
ｄｕｒｉｎｇ　ｏｐｅｒａｔｉｏｎ．

Ｍｉｓｔ　ｉｓ　ｅｍｍｉｔｔｅｄ　ｆｒｏｍ　ｔｈｅ　ａｉｒｏｕｔ　ｖｅｎｔ
ｄｕｒｉｎｇ　ｃｏｏｌｉｎｇ　ｏｐｅｒａｔｉｏｎ．

Ａ　ｓｌｉｇｈｔ　ｃｒｅｐｉｔａｔｉｏｎ　ｃａｎ　ｂｅ　ｈｅａｒｄ

ｗｈｅｎ　ｓｔａｒｔ　ｏｒ　ｓｔｏｐ　ｔｈｅ　ｕｎｉｔ．

ＡＣ　ｄｏｅｓ　ｎｏｔ　ｒｕｎ．

　　　　　　　　　Ｔｒｏｕｂｌｅ　ｓｈｏｏｔｉｎｇ

ｆｌｏｗｉｎｇ　ｉｎｓｉｄｅ　ｔｈｅ　ｕｎｉｔ．

Ｂｅｃａｕｓｅ　ｔｈｅ　ａｉｒ　ｏｆ　ｔｈｅ　ｒｏｏｍ　ｉｓ　ｃｏｏｌｅｄ　
ｄｏｗｎ　ｒａｐｉｄｌｙ　ｂｙ　ｔｈｅ　ｃｏｌｄ　ｗｉｎｄ　ａｎｄ　ｉｔ
ｌｏｏｋｓ　ｌｉｋｅ　ｔｈｅ　ｆｏｇ．

Ｔｈｉｓ　ｉｓ　ｃａｕｓｅｄ　ｂｙ　ｔｈｅ　ｇｒａｔｉｎｇ　ｎｏｉｓｅ

ｗｈｉｃｈ　ｉｓ　ｍａｄｅ　ｂｙ　ｔｈｅ　ｅｘｐａｎｄｉｎｇ　ｏｆ

ｐａｎｅｌ．

·Ｈａｓ　ｔｈｅ　ｐｏｗｅｒ　ｂｅｅｎ　ｓｈｕｔ　ｄｏｗｎ？

·Ｉｓ　ｔｈｅ　ｐｏｗｅｒ　ｐｌｕｇ　ｗｅｌｌ　ｐｌｕｇｇｅｄ　ｉｎ？

·Ｉｓ　ｔｈｅ　ｌｅａｋａｇｅ　ｐｒｏｔｅｃｔｉｏｎ　ｓｗｉｔｃｈ

·ｔｒｉｐｐｉｎｇ　ｏｆｆ？

ｃｕｔ　ｏｆｆ

·Ｉｓ　ｖｏｌｔａｇｅ　ｈｉｇｈｅｒ２５３Ｖ　ｏｒ　ｌｏｗｅｒ１９５Ｖ？

·Ｈａｓ　ｔｈｅ　ＴＩＭＥＲ　ＯＮ　ｂｅｅｎ　ｗｅｌｌ　ｓｅｔ？

Ｃｏｏｌｉｎｇ（Ｈｅａｔｉｎｇ）ｅｆｆｉｃｉｅｎｃｙ　ｉｓ　ｂａｄ．

Ｒｅｍｏｔｅ　ｃｏｎｔｒｏｌ　ｉｓ　ｎｏｔ　ａｖａｉｌａｂｌｅ

·Ｒｅｍｏｔｅ　ｃｏｎｔｒｏｌ　ｃａｎ＇ｔ　ｂｅ　ｕｓｅｄ　ｏｃｃａｓｉｏｎ－
　　　　　　　ａｌｌｙ　ｗｈｅｎ　ｔｈｅ　ａｉｒ　ｃｏｎｄｉｔｉｏｎｅｒ　ｉｓ

·Ｉｓ　ＳＥＴ　ＴＥＭＰ．ｓｕｉｔａｂｌｅ？

·Ｉｓ　ａｉｒ　ｉｎｌｅｔ　ｏｒ　ｏｕｔｌｅｔ　ｏｂｓｔｒｕｃｔｅｄ？

·Ａｒｅ　ａｉｒ　ｆｉｌｔｅｒｓ　ｄｉｒｔｙ？

·Ｉｓ　ｉｎｄｏｏｒ　ｆａｎ　ｓｐｅｅｄ　ｓｅｔ　ａｔ　ｌｏｗ　ｓｐｅｅｄ？

·Ｉｓ　ｔｈｅｒｅ　ａｎｙ　ｏｔｈｅｒ　ｈｅａｔ　ｓｏｕｒｃｅ　ｉｎ　

ｄｉｓｔｕｒｂｅｄ　ｏｒ　ｃｈａｎｇｉｎｇ　ｉｔｓ　ｆｕｎｃｔｉｏｎｓ　ｆｒｅｑ－

ｕｅｎｔ　ｔｉｍｅ，ｐｕｌｌ　ｏｕｔ　ｔｈｅ　ｐｏｗｅｒ　ｐｌｕｇ　ａｎｄ　ｉｎ－

ｓｅｒｔ　ｉｔ　ａｇａｉｎ　ｔｏ　ｒｅｃｏｖｅｒ　ｔｈｅ　ｏｐｅｒａｔｉｏｎ．

·Ｉｆ　ｉｔ　ｉｓ　ｉｎ　ｔｈｅ　ｒｅｃｅｉｖｅｄ　ｓｃｏｐｅ？　ｏｒ　

·ｔｈｅｒｅ　ｉｓ　ｂｌｏｃｋａｇｅ　ｉｎｓｉｄｅ．

·Ｃｈｅｃｋ　ｉｆ　ｔｈｅ　ｂａｔｔｅｒｉｅｓ　ａｒｅ　ｓｕｆｆｉｃｉ－
ｅｎｔ　ｏｒ　ｒｅｐｌａｃｅ　ｔｈｅ　ｂａｔｔｅｒｉｅｓ．

２０

Ｒｅｐａｉｒ　ａｎｄ　Ｍａｉｎｔｅｎａｎｃｅ

When the following circumstance occur, stop the unit from running

immediately and plug out power plug, then contact Gree Service Center.

▲Harsh noise is heard when the unit is running；
▲Air switch or creepage protect switch often trips;
▲Other things or water poured into unit or wireless

remote control carelessly;

▲Indoor water leakage occurs;
▲Power hose and power plug are extremely hot.
▲Abnormal odor is produced when the unit is running.

Please contact Gree

Service center if there

is any problem

２１

ENVIRONMENTAL INFORMATION

This unit contains fluorinated gases with greenhouse effect covered by the Kyoto Protocol.
Maintenance and disposal must be carried out by qualified persons only.
Refrigerant gas R410A, GWP = 1730

EXTRA REFRIGERANT CHARGE

Pursuant to Regulation EC 842/2006 on certain fluorinated greenhouse gases, in case of extra
refrigerant charge, it is compulsory to:

- Fill in the label accompanying the unit inserting the factory quantity of refrigerant

charge (see the technical label), the extra refrigerant charge and the total charge.

- Apply the label next to the technical label applied on the unit. For the split-type air

conditioner apply on the outdoor unit.

30