Sinclair ASH-09AK PT, ASH-13AK, ASH-18AK, ASH-24AK PT User Manual

USER'S MANUAL

KING SE

RIE

ASH-09AK PT, ASH-13AK,

ASH-18AK, ASH-24AK PT

■　　　　　　　　　　　　　　　　　　　　　．．．．．．．．．．．．．．．．．．．．．．．．．．．．．１

■　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　．．．．．．．．．．．．．．．．．．．４

■　　　　　　　　　　　　　　　　　　　　　　　　　　　　 ．．．．．．．．．．．．．．．．．．．．．５

■　　　　　　　　　　　　　　．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．１１

■　　　　　　　　　　　　　　．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．１３

■　　　　　　　　　　　　　　　　　　

．．．

．．．．．．．．．．．．．．１８

■　　　　　　　　　　　　　　　　　　．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．１９

■　　　　　　　　　　　　　　　　　　　．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．２１

■　　　　　　　　　　　　　　　　　　．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．１６

■　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　．．．．．．．．．．．．．．．．．２３

■　　　　　　　　　　　　　 ．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．３

■　　　　　　　　　　　　　　　 ．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．１０

Do not dispose this product as unsorted municipal waste.
Collection of such waste separately for special treatment

is necessary.

CONTENTS

Operation and maintenance

Notices for operation

Notices for use

Names and functions of each part

Operation of wireless remote control

Clean and care

Troubleshooting

Installation service

Notices for installation

Installation dimension diagram

Install indoor unit

Install outdoor unit

Test operation and check after installation

This symbol stands for the items
should be forbidden

This symbol stands for the items
should be followed

Emergency operation

The figures in this manual may be different with the material objects, please refer
to the material objects for reference.

．．．

．．．．．．．．．．．

．．．

．．．

■

..............

２４

Installation and Maintenance of Healthy Filter

Thank you for choosing SINCLAIR air conditioner. For correct operation, please

carefully for consultation.

read this owner's manual carefully before operating the unit and keeps it

■　　　　　　　　　　　　　　　　　　　　　．．．．．．．．．．．．．．．．．．．．．．．．．．．．．１

■　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　．．．．．．．．．．．．．．．．．．．４

■　　　　　　　　　　　　　　　　　　　　　　　　　　　　 ．．．．．．．．．．．．．．．．．．．．．５

■　　　　　　　　　　　　　　．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．１１

■　　　　　　　　　　　　　　．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．１３

■　　　　　　　　　　　　　　　　　　

．．．

．．．．．．．．．．．．．．１８

■　　　　　　　　　　　　　　　　　　．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．１９

■　　　　　　　　　　　　　　　　　　　．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．２１

■　　　　　　　　　　　　　　　　　　．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．１６

■　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　．．．．．．．．．．．．．．．．．２３

■　　　　　　　　　　　　　　　　　　．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．３

■　　　　　　　　　　　　　　　 ．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．１０

Do not dispose this product as unsorted municipal waste.
Collection of such waste separately for special treatment

is necessary.

CONTENTS

Operation and maintenance

Notices for operation

Notices for operation

Names and functions of each part

Operation of wireless remote control

Clean and care

Troubleshooting

Installation service

Notices for installation

Installation dimension diagram

Install indoor unit

Install outdoor unit

Test operation and check after installation

This symbol stands for the items
should be forbidden

This symbol stands for the items
should be followed

Emergency operation

The figures in this manual may be different with the material objects, please refer
to the material objects for reference.

．．．

．．．．．．．．．．．

．．．

．．．

1

★

★

★

★

★

The power supply

must adopt the

special circuit that with air

switch protection and assure

★

★Keep combustilble

spray away from the

units more than 1m.

★

Don't block the air
intake or outlet vents

of both the outdoor and indoor
units.

It can decrease the air conditioning
capacity or cause a malfunction.

Don’t leave windows
and doors open for

a long time while operating
the air conditioner.

It can decrease the air
conditioning capacity.

It can cause a fire or explosion

Don’t attempt to
repair the air

conditioner by yourself.

The wrong repair will lead to
an electric shock or fire, so
you should contact the service
center to repair.

Be sure to pull out
the power plug as

the air conditioner not in use
for a long time.

Otherwise, the accumulated
dusts that may cause over
heating or fire.

Never splice the
power cord or use

an extended cord.

It can cause overheating or
fire.

When having a

burning smell or

smoke, please turn off the
power supply and contact
with the service center.

If the abnormity still exists,
the unit may be damaged,
and may cause electric
shock or fire.

Please read the following carefully before operating

Notices for operation

components would be easily
damaged, when the voltage
is very low, the compressor
vibrates terribly and that the
refrigerant system will be
damaged, the compressor
and electric components
cannot work, the voltage
should be stable; there
shouldn’t be big fluctuation.

When the voltage
is very high, the

it has enough capacity.

The unit will be turned
on or off according to your
requirement automatically,
please do not turn on or turn
off the unit frequently, other­wise disadvantage effect may
be caused to the unit.

2

★

★

★

★

★

★

★

★

Notices for use

Don’t apply the cold wind to
the body for a long time.

It can cause the health problems.

Splashing water on the air
conditioner can cause an electric

shock and malfunction.

Don’t place a space heater

near the air conditioner.

Don’t blow the wind to animals
and plants directly. It can cause

a bad influence to them.

Don’t insert your hands or stick into
the air intake or outlet vents.

Don’t use the air conditioner

for other purposes, such as

drying clothes, preserving foods, etc.

To adjust the airflow direction

appropriately. At operating,the
louvers of air conditioner could be adjusted
by pressing the SWING button on wireless
remote control to change the airflow direction.

Swing louver

Guide louver

Please don't cut off or damage the
power cords and control cords.

If they are damaged, please ask the qualified
personnel to change them.

3

Notices for operation

Working principle and special functions for cooling

Principle:

Air conditioner absorbs heat in the room and transmit to outdoor and discharged,
so that indoor ambient temperature decreased, its cooling capacity will increase

or decrease by outdoor ambient temperature.

Anti-freezing function

If the unit is running in COOL mode and in low termperature, there will be frost formed
on the heat exchanger, when indoor heat exchanger temperature decreased below 0
the indoor unit microcomputer will stop compressor running and protect the unit.

Working principle and special functions for heatin

g

Principle:

*

Air conditioner absorbs heat in the room and transmit to outdoor and discharged,
will increase, its heating capacity will decrease by outdoor ambient temperature.

so that indoor ambient temperature increased, so room heating capacity.

*

If outdoor temperature got lower, please operate with the other heating ventilating
equipments.

Defrosting:

*

When outdoor temperature is low but high humidity, after a long while running,
frost will form on outdoor unit, that will effect the heating effect, at this time,

the auto defrosting function will act, the heat running will stop for 8-10mins.

*

During the auto defrosting, the fan motors of indoor unit and outdoor unit will stop.

*

During the defrosting, the indoor indicator flashes, the outdoor unit may emit vapor.

This is due to the defrosting, it isn't malfunction.

*

After defrosting finished,the heating will recover automatically.

Anti-freezing function:

In "HEAT" mode, if in the following status, the indoor heat exchanger haven't achieve

the certain temperature, that the indoor unit will not act, in order to prevent cool air blowing.

(Within 3mins)

1.Heating starts. 2.After Auto defrosting finished. 3.Heating under the low temperature.

The climate type of this unit is according to the nameplate.

Plasma Technology PLASMA TEC

Only for models ASH-09AK PT and ASH-24AK PT
Plasma Air Purification Technology PLASMA TEC produces a natural bio-climate rich in active oxygen
molecules, known as ions. It creates optimal quantity of positive and negative oxygen ions. Such an
ion-enriched environment is notably cleaner and fresher. Plasma Technology has the capacity of
breaking down bacteria into harmless particles, air purification, odor neutralization and reduction of
particles in the air. All these qualities make PLASMA TEC Technology invaluable also for allergic
persons.

4

⑴

⑴

⑹

⑶

⑵

⑸

⑷

⑺

⑼

⑹

⑸

⑵

⑻

⑼

⑷

⑺

⑶

⑻

Names and functions of each part

Indoor unit

Air in

Air out

Manual switch

Front panel

Filter

Guide louver

Receiving window

Bind tape

Connection wire

Drainage pipe

Remote control

Outdoor unit

Air in

Air out

遥控器各按键的名称及作用

５

Names and functions of wireless remote control

●

Press this button, the unit will be turned

on, press it once more, the unit will be

ON/OFF button

ON/OFF

Remote control

Signal transmitter

AUTO

COOL

DRY

FAN

HEAT

(only for cooling and heating unit)

Don't drop or throw the remote control; Don't let any liquid in the remote control and

Note: Be sure that there are no obstructions between receiver and remote controoler;

Middle fan

turned off. Sleep function will be canceled,

put the remote control directly under the sunlight or any place where is very hot.

while unit off.

●

Press this button, Auto, Cool,Dry, Fan,

Heat mode can be selected circularly.

MODE button

MODE

Auto mode is default while power on.

Under Auto mode,the temperature will not

be displayed; Under Heat mode, the
initial value is 28℃

;Under other

modes,

the initial value is 25℃

．

●

Press this button, Sleep On and Sleep
Off can be selected. After powered on,Sleep

SLEEP button

SLEEP

Off is defaulted. After the unit is turned
off, the Sleep function is canceled. After
Sleep function set up, the signal of Sleep

will display. In this mode, the time of timer
can be adjusted. Under Fan and Auto
modes, this function is not available.

●

Press this button, Auto, Low, Middle, High

speed can be circularly selected. After

FAN button

FAN

powered on,Auto fan speed is default.
Under Blow mode, Low fan speed only
can be set up.

Low fan

High fan

●

Press this button, the clock can be set up,

signal blink and display.Within 5

CLOCK button

CLOCK

seconds, the value can be adjusted by
pressing + or - button, if continuously
press this button for 2 minutes above,
in every 0.5 seconds, the value on ten place
of Minute will be increased 1. During blinking,
repress the Clock button or Confirm button,

signal will be constantly displayed and
it denotes the setting succeeded. After
powered on, 12:00 is defaulted to display
and signal will be displayed. If there is

current time value is Clock value, otherwise
is Timer value.

signal be displayed that denotes the

TEMP button

TEMP

Operation of wireless remote control

（

ｏ

Ｆ）

82

（

ｏ

Ｆ）

77

●

Press this button, can set up and select:

setting temperature (displaying the room),

indoor ambient temperature (displaying
indoor temperature), outdoor ambient
temperature (displaying outdoor tempe­rature),if there no outdoor ambient

temperature displaying be required that will
keep original display status. and circulate

like this. No signal displayed. Remark: When

operating this button,the setting temperature
is displayed all the time on the wireless
remote control.

６

Remote control

buttons of this control which are not available to this unit will not be described below.

This wireless remote control is universal, and it could be used for many units, some

●

Press this button, the Blow On and Blow

Off can be set up. Under the Cool and Dry

BLOW button

BLOW

mode, press this button once, the signal
"DRY" will be displayed, and BLOW is
turned on; When repressing this button

once more, signal "DRY" will be concealed,

at this time, the BLOW is turn off. After
powered on, Blow Off is defaulted. If
operating ON/OFF button and changing
mode to Cool, Dry, the status of BLOW
will stay in the original position. If unit
is off, only Blow off can be set up and send
the signal. This function is not available
under the Auto, Fan and Heat mode
and there is no Blow signal displayed.

●

Under Cool or Heat mode, press this

button can turn on or turn off the Turbo

TURBO button

TURBO

function.After the Turbo function turned
on, the signal of Turbo will display. The
signal will be automatically cancelled if
changing the mode or fan speed.

●

Press this button at unit On or Off status,

Light On and Light Off can be set up.

LIGHT button

LIGHT

After powered on, Light On is defaulted.

●

Presetting temperature can be increased.

Press this button, the temperature can be

+ button

+

set up, continuously press this button
and hold for two seconds, the relative
contents can quickly change, until unhold

this button and send the order that the ℃
（ｏＦ）signal will be displayed all the time.

The temperature adjustment is unava­ilable under the Auto mode, but the order
can be sent if pressing this button.
Temperature of Celsius degree setting:
16-30 ; for Fahrenheit degree setting:
61-86.

●

Presetting temperature can be decreased.

Press this button, the temperature can be

- button

-

set up, continuously press this button
and hold for two seconds, the relative
contents can quickly change, until unhold

this button and send the order that the ℃
（ｏＦ）signal will be displayed all the time.

The temperature adjustment is unav­ailable under the Auto mode, but the order
can be sent by if pressing this button.

Names and functions of wireless remote control

Operation of wireless remote control

７

●

Press this button to set swing angle,

which circularly changes as below:

OFF

This remote controller is universal.If it

receives threes kinds of following status,

the swing angle will remain original.

If guide louver is stopped when it is

swinging up

and down,it will remian its

present position.

indicates guide louver swings back and

forth

in the five places,as shown in the

figure.

SWING UP AND DOWN BUTTON

TIMER ON

TIMER ON BUTTON

Timer On setting: Signal “ON” will blink
and display, signal will conceal, the
numerical section will become the timer
on setting status. During 5 seconds blink,
by pressing ＋ or － button to adjust the
time value of numerical section, every
press of that button, the value will be
increased or decreased 1 minute. Hold
pressing ＋ or －button, 2 seconds later,
it quickly change, the way of change is:
During the initial 2.5 seconds, ten numbers
change in the one place of minute, then
the one place is constant, ten numbers
change in the tens place of minute at 2.5
seconds speed and carry. During 5s blink,
press the Timer button, the timer setting
succeeds. The Timer On has been set up,
repress the timer button, the Timer On
will be canceled. Before setting the
Timer, please adjust the Clock to the
current actual time.

TIMER OFF BUTTON

●One press this key to enter into

TIMER OFF setup, in which case
the TIMER OFF icon will blink.
The method of setting is the same

TIMER OFF

as for TIMER ON.

●

Remote control

buttons of this control which are not available to this unit will not be described below.

This wireless remote control is universal, and it could be used for many units, some

Names and functions of wireless remote control

Operation of wireless remote control

８

★

This function indicates that moisture on evaporator of indoor unit will be blowed after the unit

About blow function

is stopped to avoid mould.

1. Having set blow function on: After turning off the unit by pressing ON/OFF button
indoor fan will continue running for about 10 min. at low speed. In this period,

press blow button to stop indoor fan directly.

2. Having set blow function off: After turning off the unit by pressing ON/OFF button,
the complete unit will be off directly.

Operation of wireless remote control

Introduction for special function

1. After powered on, press ON/OFF button, the unit will start to run.(Note: When

it is powered on, the guide louver of main unit will close automatically.)

2. Press MODE button, select desired running mode, or press COOL or HEAT
mode to enter into the corresponding operation directly.

3. Pressing +or - button, to set the desired temperature (It is unnecessary

to set the temp. at AUTO mode.)

4. Pressing FAN button, set fan speed, can select AUTO FAN, LOW, MID

and HIGH.

5. Pressing button, to select the swing.

1. Press SLEEP button, to set sleep.

2. Press TIMER ON and TIMER OFF button, can set the scheduled timer on

3. Press LIGHT button, to control the on and off of the displaying part of the

unit (This function may be not available for some units).

4. Press TURBO button, can realize the ON and OFF of TURBO

function

or timer off.

Guide for operation- General operation

Guide for operation- Optional operation

When AUTO RUN mode is selected, the setting temperature will not be displayed on the

LCD, the unit will be in accordance with the room temp. automatically to select the suitable

running method and to make ambient comfortable.

About turbo function

If start this function, the unit will run at super-high fan speed to cool or heat quickly so that

the ambient temp. approachs the preset temp. as soon as possible.

★

★

About AUTO RUN

９

Press +and - buttons simultaneously to lock or unlock the keyboard. If the remote controller
is locked, the icon

flicker for three times. If the keyboard is unlocked, the mark will disappear.

1. Press swing up and down button continuously more than 2s,the main unit will swing back
and forth form up to down, and then loosen the button, the unit will stop swinging and present
position of guide louver will be kept immediately.

2. Under swing up and down mode, when the status is switched from off to , if press this
button again 2s later, status will switch to off status directly; if press this button again

within 2s,the change of swing status will also depend on the circulation sequence stated above.

About switch between Fahrenheit and Centigrade

Under status of unit off, press +and - buttons simultaneously to switch

℃　ａｎｄ　．

It indicates: after starting this function by remote controller and the unit has been under
defrost status, If turn off the unit by remote controller, the unit will not stop defrosting until

it is finished; if change setting mode by remote controller, the function ,which is set last
time, won't be carried out until defrosting finished.

Operation of this function on or off: If remote controller is under off status, press mode button
and blow button simultaneously in order to enter or cancel this new function. If the unit is under

defrost mode, dual eight position on remote controller will display H1.If switch to heat mode,
the position will display H1, which flickers for 5s, in which case, press +/- button, H1 will
disappear and setting temp. be displayed.

After remote controller is powered on, the new defrost function will be defaulted to be closed.

★

★

★

★

About swing up and down

About lock

About new function of defrosting

will be displayed on it, in which case, press any button, the mark will

Operation of wireless remote control

1.

４.

２.

３．

★

●

●

●

●

●

Slightly to press the place with , along the arrowhead direction to push the back cover of wireless

remote control. (As show in figure)

Take out the old batteries. (As show in figure)
Insert two new AAA1.5V dry batteries, and pay attention to the polarity.

(As show in figure)
Attach the back cover of wireless remote control. (As show in figure)

When changing the batteries, do not use the old or different batteries,

If the wireless remote control will not be used for a long time, please

otherwise, it can cause the malfunction of the wireless remote control.

take them out, and don't let the leakage liquid damage the wireless

remote control.

The operation should be in its receiving range.
It should be placed at where is 1m away from the TV set or stereo sound sets.

If the wireless remote control can not operate normally, please take them out,

after 30s later and reinsert, if they cannot normally run, please change them.

Sketch map for
changing batteries

NOTE:

Changing batteries and notices

１０

●

●

●

●

Emergency Operation

Emergency Operation

When the wireless remote control is lost or damaged, please use the manual switch, at
this time, it is running in Auto Run mode that will not change the temperature setting
value and fan speed.

The manual switch can be operated as follow:

At operation: When the unit stopped running,
press ON/OFF button, unit will enter into AUTO
RUN mode. The microcomputer will accord to
the room temperature to select the (COOL,
HEAT, FAN) mode automatically, to obtain the
comfortable effect.

At stopping:When the unit is running, press the
ON/OFF button of the manual switch, the unit
will stop work.

The code swich can be operated as follow:

At operation: When the unit is stopped running,
adjust the code switch to AUTO, the unit will
enter into AUTO RUN mode. The microcomputer
will accord to the room temperature to select the
(COOL, HEAT, FAN) mode automatically, to
obtain the comfortable effect.

At stopping: When the unit is running, adjusts
the code switch to STOP position, the unit will
stop work.

Code Switch

Manual Switch

AUTO/STOP

1１

●●

●

●●

①

②

③

Clean and care

CAUTION

Turn power off and pull out the power plug before cleaning air conditioner. Or it may
cause electric shock.

Never sprinkle water on the indoor unit and the outdoor unit for cleaning because i

t

can cause an electric shock

.

Volatile liquid (e.g. thinner or gasoline) will damage the air conditioner. (So wipe th

e

units with a dry soft cloth, or a cloth slightly moistened with water or cleanser.

)

Clean the front panel(m

ake sure to take it off before cleaning)

Take off the front panel

Along the direction of arrows to lift the front panel

up, meanwhile t

o hold both slots of the front panel

and t

ake it out forcibly and then can take it off.

Washing

Clean

with a soft brush, water and neutral detergent,

and then t

o dry it.(Note: Never use the water above

45 to

℃ wash the panel, or it could cause deformation

or discolouration.)

Install front panel

Place two supporters of the front panel into the slots,

along the

direction of arrows to cover and clasp the

front panel. As show

in righ figure.

Cleaning the air filters (Recommended once every three months)

Note: If dust is much more around the air conditioner, the air filters should be cleaned many

times. After taking off the filter, don't touch the fin of indoor unit, in order to avoid hurt your

fingers.

1２

①

②

③

④

①
②

③

Check before use

Be sure that nothing obstructs the air outlet and intake
vents.

Check that whether ground wire is properly connected
or not.

Check that whether the batties of air conditioner are
changed or not.

Check that whether the installation stand of the outdoor
unit is damaged or not. If damaged, please contact the dealer.

Maintain after use

Turn main power off.

Clean the filter and indoor and outdoor units' bodies.

Repaint the rubiginous place on the outdoor unit to prevent it from spreading.

②

③

①

(a)

(b

)

Clean and care

Take down the air filter

Cleaning

Reinsert the filters

Reinsert the filters along with the arrow head, then cover
the surface panel and clasp it.

To clean the dust adhering to the filters, you can either
use a vacuum cleaner, or wash them with warm water
(the water with the neutral detergent should below 45

℃).

When the filters are very dirty (such as oil stain), and

dry it in the shade.

NOTE: Never use water above 45℃to wash, or it can
cause deformation or discoloration. Never partch it by
fire, or can cause a fire or deformation.

At the slot of surface panel to open an angle, pull the

air filter downward and take it out.

1３

●

●

●

●

●

●

Troubleshooting

Warning

Do not repair the air conditioner at your discretion. Incorrect repair may cause electric
shock or fire, so please contact Authorized Service Center for professional repair.
Following checks prior to contact may save your time and costs.

Air conditioner does not run upon immediately
restart after a stop.

Phenomenon

To protect the air conditioner upon
immediate restart after a stop, the
microcomputer controller will delay
the unit for 3 minutes before the air
conditioner will run.

Troubleshooting

Air conditioner blows out bad smell when
it is initially started.

You may hear “Water Flowing” noise
when the air conditioner is running.

Sometimes a thin fog will flow out of the
outlet when air conditioner is running
under cooling mode.

You may hear a slight crack when the
air conditioner is started or stopped.

The air conditioner itself has no bad smell.
If any. It is the bad smell accumulated from
environment. Solution: Clean the air filter.

If still any problem, the air conditioner shall
be cleaned (Please contact Authorized
Service Center)

When the air conditioner is started, or the
compressor is started or stopped during
running or the air conditioner is stopped,
sometimes you may hear “hua-hua” or “di-di-”
noise. This is the flowing sound of refrigerant
other than fault.

This might occur when indoor temperature
and humidity are high. This is because the
indoor air is quickly cooled down.
After a period of time, the fog will disappear
with the decrease of indoor temperature
and humidity.

This is the sound of friction caused by
expansion of panel or other parts due
to the change of temperature.

Wait

1４

●

●

●

●

●

●

●

●

●

●

●

●

●

●

●

●

●

●

●

●

●

●

Troubleshooting

The unit can not run

Break off

Cooling(Heating) efficiency is not good.

Wireless remote control is not available

If water leakage in the room

If water leakage in outdoor unit

Noise from indoor unit emitted.

Phenomenon

Troubleshooting

Has the power been shut down?

Is voltage higher or lower?

(Tested by professionals)

Is the Timer correctly used?

Is the circuit protection device tripped off or not?

Is Temp. setting suitable?
Were inlet and outlet vents obstructed?

Are the windows and doors clothed?
Did Fan speed set at low speed?
Is there any heat sources in the room?

The unit is interfered by abnormal or frequent
functions switchover occasionally the controller
cannot operate. At this time, you need to pull
out of the plug, and reinsert it.

Is it in its receiving range? Or obstructed?

To check the voltage in wireless remote control

inside is charged, otherwise to replace the

batteries.

Whether the wireless remote control is damaged.

The air humidity is on the high side.
Condensing water over flowed.

The connection position of indoor unit drainage

pipe is loosed.

When the unit is running in COOL mode, the
pipe and connection of pipe would be condensed

due to the water cooled down.

When the unit is running in Auto Defrosting mode,

the ice thawed and flowed out.

When the unit is running in HEAT mode, the

water adhered on heat exchanger dripped off.

The sound of fan or compressor relay is switching
on or off.

When the defrosting is started or stop running,
it will sound. That is due to the refrigerant flowed
to the reverse direction.

Dose power plug come loose from the socket?

Is there too much dusts accumulated and
obstructed the filter?

１５

●

●

●

●

Troubleshooting

Phenomenon

Troubleshooting

Indoor unit cannot deliver air

Moisture on air outlet vent

Immediately stop all operations and plug out, contact
the dealer in following situations.

There is harsh sound during operation

The terrible odors emitted during operation

Water is leaking in the room

Air switch or protection switch often breaks

Carelessy splash water or something into unit

There is an abnormal heat in power supply cord
and power plug.

Stop running and pull out of the plug.

If unit is running under the high humidity for
a long time, the moisture will be condensed
on the air outlet grill and drip off.

In HEAT mode, when the temperature of
indoor heat exchanger is very low, that

will stop deliver air in order to prevent cool

air. (Within 3min)

In HEAT mode, when the outdoor temperatur

e

is low or high humidity, there are much frost

be formed on the outdoor heat exchanger,
that the unit will automatically defrost, indoor
unit stop blowing air for 8-10min.During the
defrosting, there is water flowing out or vapor
be produced.

In dehumidifying mode, sometimes indoor

fan will stop, in order to avoid condensing

water be vaporized again, restrain temper-

ature rising.

1６

●

●

●

●

●

●

Installation service- Notices for installation

Important Notices

1. The unit installation work must be done by qualified personnel according to the local
rules and this manual.

Basic Requirements For Installation Position

Install in the following place may cause malfunction. If it is unavoidable contact with

service center please:

Place where strong heat sources, vapors, flammable gas or volatile ob

juct are emitte

d

Place where high-frequency waves are generated by radio equipment, welders and
medical equipment.

Place where a lot of salinities such as coast exists.
Place where the oil (machine oil) is contained in the air.

Place where a sulfured gas such as the hot spring zones is generate

d.

Other place with special circumstance.

Indoor Unit Installation Position Selection

1. The air inlet and outlet vent should be far from the obstruction, make sure that the air
can be blown through the whole room.

2. Select a position where the condensing water can be easily drained out, and the place
is easily connected for outdoor unit.

3. Select a location where the children can not reach.

4. Can select the place where is strong enough to withstand the full weight and vibration of
the unit. And will not increase the noise.

5. Be sure to leave enough space to allow access for routine maintenance. The height of the
installed location should be 230 cm or more from the floor.

6. Select a place about 1m or more away from TVset or any other electric appliances.

7. Select a place where the filter can be easily taken out.

8. Make sure that the indoor unit installation should accord with installation dimension

diagram requirements.

Outdoor Unit Installation Position Selection

1. Select a location from which noise and outflow air emitted by unit will not inconvenience

neighbors, animals, plants.

2. Select a location where there should be sufficient ventilation.

3. Select a location where there should be no obstructions cover the inlet and outlet vent.

4. The location should be able to withstand the full weight and vibration of the outdoor unit
and permit safe installation.

5. Select a dry place, but do not expose under the direct sunlight or strong wind.

6. Make sure that the outdoor unit installation dimension should accord with installation
dimension diagram, convenient for maintenance, repair.

7. The height difference of connecting the tubing within 5m, the length of connecting the

tubing within 10m.

8. Select a place where it is out of reach for the children.

9. Select a place where will not block the passage and do not influence the city appearance.

2. If the air conditioner has not plug, directly connect it into the fixed circuit, a breaker should be
installed in the fixed circuit. all pole of this breaker should be switching off and the distance

of the contact should be at least 3mm.

1７

① ②
③

④

3

4.

1.

2.

2

Notices for installation

Earthing requirements

Others

Safety Requirements For Electric Appliances

The connection method of unit and power cable as well as the interconnect method
of each isolated component should refer to the circuit diagram stick on the unit.

The model of the blown fuse and rated value should refer to the silk-screen on the
controller or fuse sleeve.

1. Air conditioner is type 1 electric appliance, thus please do conduct reliable earthing
measure.

2. The yellow-greentwo-colorwireinairconditioner is earthing wire and cannot be used
for other propose. It cannot be cut off and be fix it by screw, otherwise it would cause

electric shock.

3. The earth resistance should accord to the National Criterion.

4. The user power must offer the reliable earthing terminal. Please don't connect the

earthing wire with the following place:

Tap water pipe Gas pipe

Contamination pipe

Other places that professional personnel consider them unreliable.

Note:

Make sure that the Live wire or Zero line as well as the earth wire in the family power
socket can not be wrong connected, there should be reliable and no short circuit in the
diagram.

wrong connection may cause fire.

The min. distance from the unit and combustive surface is 1.5m.

It should be reliably earthed, and it should be connected to the special earth device,
the installation work should be operated by the professional.

The air switch must have the functions of magnetic tripping and heat tripping, in order

to protect the short circuit and overloading.

1. The power supply should be used the rated voltage and AC exclusive circuit,

the power cable diameter should be satisfied.
Don't drag the power cable emphatically.

●

●

3. The appliance shall be installed in accordance with national wiring regulations.

4. This appliance is not intended for use by persons (including children) with reduced

physical, sensory or mental capabilities, or lack of experience and knowledge, unless

they have been given supervision or instruction concerning use of the appliance by a

person responsible for their safety.

5. Children should be supervised to ensure that they do not play with the appliance.

Installation dimension diagram

1８

mc05

Installation dimension diagram

Space to the ceiling

Above

Above

Above

Above

Space to the wall

Space to the wall

Space to the wall

Above

Above

Above

m

c

0

3

50cm

0

2

0

15cm

15cm

300

cm

2

15
cm

Space to the floor

Air outlet side

Space to the obstruction

Air outlet side

Air inlet side

Above

m

c

0

2

m

c

0

Above

30cm

Above

cm

cm

230

1９

Install indoor unit

Install the rear panel

1.Always mount the rear panel horizontally. As the water drainage pipe at the left, when adjusting the rear
panel, this side should not be too high; the right side should be slightly high.

2. Fix the rear panel on the selected location

3. Be sure that the rear panel has been

fixed firmly enough to withstand the weight

of an adult of 60kg, furthermore, the weight
should be evenly shared by each screw.

Install the piping hole

1. Make the piping hole in the wall at a slight downward slant to the outdoor
side.

2. Insert the piping-hole sleeve into the hole to prevent the connection
piping and wiring from being damaged when passing through the hole.

Install the water drainage pipe

1. For well draining, the drain hose should be placed at a
downward slant.

2. Do not wrench or bend the drain hose or flood its end
by water.

3. When the long drainage hose passing through indoor,
should wrap the insulation materials.

Wrenched

Bent

Flooded

Indoor

Outdoor

Wall pipe

Seal pad

Fig.1

(Rear piping hole)

(Rear piping hole)

Left

Right

Mark on the middle of it

Gradienter

Space to
the wall
150mm
above

Space to
the wall
150mm
above

Wall

Wall

Connect indoor and outdoor electric wires

1. Open the front panel upwardly.

2.Screw off the fixing screw of cover plate and screw off cover plate.

3. Put the power connection cable through the back of indoor unit wire hole and take it out.

4. All the wiring should be connected according to the circuit diagram on the unit.

5. Put the power connection cable the section, which with sheath into wire groove, and
cover the cover plate, screw on the fixing screw, tighten the connection wire.

6. Cover the front panel cover.

7. For the cooling and heating unit, signal control wire can be passed through the connection
of connector and indoor unit, and use the wire clip that is under the body case, tighten the
signal control wire.

２０

●

●

●

●

●

1.

2.

(N·m)

Ф6

Ф 9.52

Ф 12

31～35

15～20

50～55

Ф 16 60～65
Ф 19 70～75

2.

3.

●

1.

Install indoor unit

NOTE:

When connecting the electric wire if the wire length is not enough, please contact with

the authorized service shop to buy a exclusive electric wire that is long enough and the

joint on the wire are not allowed.

The electric wiring must be correctly connected, wrong connection may cause spare
parts malfunction.

Tighten the terminal screw in order to prevent loose.
After tighten the screw, slightly pull the wire and confirm whether is it firm or not.

If the earth wire is wrong connection, that may cause electric shock.

The cover plate must be fixed, and tighten the connection wire, if it is poor installed, that
the dust, moisture may enter in or the connection terminal will be affected by outside force,
and will cause fire or elelctric shock.

Install the indoor unit

The piping can be lead out from right, right rear,

left, left rear.

When routing the piping and wiring from the left
or right side of indoor unit, cut off the tailings

from the chassis in necessary (show in Fig.2)

(1).Cut off the tailings 1 when routing the wiring only;
(2).Cut off the tailings 1 and tailings 2 when routing

both the wiring and piping.(or 1,2,3);

Take out the piping from body case, wrap the piping
electric wire, water pipe with tape and put them th­rough the piping hole (As show in Fig. 3)

Hang the mounting slots of the indoor unit on the
upper tabs of the rear panel and check if it is firm

enough. (As show in Fig.4)

Install the connection pipe

Align the center of the piping flare with the

relevant valve.

Screw in the flare nut by hand and then tighten

the nut with spanner and torque wrench refer

to the following.
Tightening torque table

Hex nut diameter

Tightening torque

NOTE: Firstly connect the connection pipe to indoor unit, then to outdoor unit; pay attention
to the piping bending, do not damage the connection pipe; the joint nut couldn't tighten too
much, otherwise it may cause leakage.

Spanner

Torque wrench

Indoor unit piping

Taper nut Piping

Fig.4

Fixing hook

Mounting

board

Mounting

board

Right

Left rear

Left

Right rear

Fig.3

Fig.2

Tailing 3

Tailing 2

Tailing1

Gas side piping

External connection

electric wire

Liquid side

piping

Liquid side

piping

insulation

Water drainage pipe

Finally wrap it

with tape

Gas side piping

insulation

●

Leakage circuit-breaker and air switch of correct capacity must be installed.

２１

●

●

Install outdoor unit

Air pu rgi ng and lea kag e test

Electric Wiring

1. Disassemble handle of right side plate or front side plate of outdoor unit.

4. Ensure if wire has been fixed well.

5. Install handle or front side plate.

NOTE:

Wrong wiring may cause

spare parts malfunction.

After the cable fixed, make sure

there should be a free space

between the connection and

fixing place on the lead wire.

2. Take off wire clamp, connect and fix power connect cord to terminal of line bank.
Wiring should fit that of indoor

unit.

3. Fix the power connection cable with wire clamp, for cooling and heating unit, then use the
wire clamp to fix the signal control wire, then connect the corresponding connector.

●

5

-1.0 10

pa(-76cmHg)

５

Air purging and leakage test

Liquid pipe

Gas pipe

Valve

cap

Vacuum

gauge

Vacuum pump

Fig.

1. Connect charging hose of manifold valve to charge end of low
pressure valve (both high/low pressure valves must be tightly

shut).

2. Connect joint of charging hose to vacuum pump.

3. Fully open handle handle of Lo manifold valve.

4. Open the vacuum pump to evacuate. At the beginning, slightly

loosen joint nut of low pressure valve to check if there

is air coming inside.

5. After finishing evacuation, shut Lo handle of manifold

valve to stop the vacuum pump. (Keep evacuating for

more than 15 minutes and make sure the reading of

multi-meter is

6. Fully open high/low pressure valves.

7. Remove charging hose from charging end of low
pressure valve.

8. Tighten bonnet of low-pressure valve. (As shown in Fig.5)

２２

Ø

●

Outdoor condensation drainage (Heat pump type only)

When the unit is heating, the condensing water

and defrosting water can be drained out reliably

through the drain hose.

Installation: Install the outdoor drain elbow in

25 hole on the base plate, and joint the

drain hose to the elbow, so that the wastewater
formed in the outdoor unit can be drained out

to a proper place.

Chasis

Outdoor drain

elbow

Install outdoor unit

Fig.6

Use soap water or leak hunting meter to check whether

the joints is leak.

Indoor unit check point

Indoor unit check point

Leak hunting

２３

Check after installation and test operation

Items to be checked

Possible malfunction

Has it been fixed firmly?

The unit may drop, shake or emit noise.

Have you done the refrigerant leakage test?

It may cause insufficient cooling(heating)

capacity.

Is heat insulation sufficient?

It may cause condensation and dripping.

Is water drainage well?

It may cause condensation and dripping.

Is the voltage in accordance with the rated
voltage marked on the nameplate?

It may cause electric malfunction

or damage the part..

Is the electric wiring and piping

connection installed correctly and securely?

It may cause electric malfunction

or damage the part.

Has the unit been connected to a secure

earth connection?

It may cause electrical leakage.

Is the power cord specified?

It may cause electric malfunction

or damage the part

Is the inlet and outlet been covered?

It may cause insufficient cooling(heating)
capacity.

Has the length of connection pipes

and refrigerant capacity been recorded?

The refrigerant capacity is not accurate.

Test Operation

1. Before test operation

(1) Do not switch on power before installation isfinished completely.

(2) Electric wiring must be connected correctly and securely.

(3) Cut-off valves of the connection pipes should be opened.

(4) All the impurities such as scraps and thrums must be cleared from the unit.

2. Test operation method

(1) Switch on power, press "ON/OFF" button on the wireless remote control to start the
operation.

(2) Press MODE button, to select the COOL, HEAT, FAN to check whether the operation

is normal or not.

Check after installation

ENVIRONMENTAL INFORMATION

This unit contains fluorinated gases with greenhouse effect covered by the Kyoto Protocol.
Maintenance and disposal must be carried out by qualified persons only.
Refrigerant gas R410A, GWP = 1730

EXTRA REFRIGERANT CHARGE

Pursuant to Regulation EC 842/2006 on certain fluorinated greenhouse gases, in case of extra
refrigerant charge, it is compulsory to:

- Fill in the label accompanying the unit inserting the factory quantity of refrigerant

charge (see the technical label), the extra refrigerant charge and the total charge.

- Apply the label next to the technical label applied on the unit. For the split-type air

conditioner apply on the outdoor unit.