Simrad SH40 - MINI MANUAL REV A User Manual
Mini-manual
Simrad SH40
High frequency sonar
M A X I M I Z I N G Y O U R P E R F O R M A N C E A T S E A
www.SIMRAD.com
Simrad SH40
Mini-manual
This manual provides you with the basic information
required to operate the Simrad SH40 High frequency sonar.
For more detailed information, refer to the Operator ma
nual.
302656/A
March 2006
Document history
Document number: 302656 / ISBN-10: 82-8066-067-4 / ISBN-13: 978-82-8066-067-4-1
Rev. A
March 2006 First version.
Copyright
©2006 Simrad AS
Disclaimer
The information contained in this document remains the sole property of Simrad AS. No part of this
document may be copied or reproduced in any form or by any means, and the information contained within
it is not to be communicated to a third party, without the prior written consent of Simrad AS.
Simrad AS endeavours to ensure that all information in this document is correct and fairly sta ted, but does
not accept liability for any errors or omissions.
Warning
The equipment to which this manual applies must only be used for the purpose for which it was
designed. Improper use or maintenance may cause damage to the equipment and/or injury to personnel.
The user must be familiar with the contents of the appropriate manuals before a
ttempting to operate
or work on the equipment.
Simrad disclaims any responsibility for damage or injury caused by improper installation, use or
maintenance of the equipment.
Support
If you require maintenance on your Simrad equipment, contact your local dealer. You can also contact
Simrad using the following e-mail address:
e-mail: contact@simrad.com
Strandpromenaden 50
P. O .B o x 1 11
N-3191 Horten,
Norway
Simrad AS
Telephone:+4733034000
Telefax:+4733042987
simrad.sales@simrad.com
www.simrad.com
Mini-manual
Table of contents
INTRODUCTION ................................................................ 5
IMPORTANT MATTERS ...................................................... 6
RELEASES ......................................................................... 7
SH40 Release history ...............................................................................................7
POWER ON/OFF................................................................ 8
How to s witch on the sonar......................................................................................8
How to switch off the sonar......................................................................................9
SONAR CONTROL PANEL ................................................. 10
OPERATIONAL MODES .................................................... 12
USING THE MENUS.......................................................... 14
Menu structure........................................................................................................14
Menu buttons..........................................................................................................15
How to h ide the menu ............................................................................................16
Horizontal menu.....................................................................................................16
Vertical menu..........................................................................................................17
Display menu..........................................................................................................18
Setup menu.............................................................................................................18
COMMON P ROCEDURES................................................... 21
Menu procedures ....................................................................................................21
How to hide the menu.................................................................................21
How to simplify the menu ...........................................................................21
Gain adjustment procedures ...................................................................................21
How to adjust the gain.................................................................................22
How to control the RCG.............................................................................. 22
How to control the TVG.............................................................................. 23
Mode procedures ....................................................................................................23
How to select operational mode................................................................... 23
How to define the function of the Mode buttons............................................ 24
How to sort the operationalmodes............................................................... 24
Storage procedures .................................................................................................24
How to store sonar images........................................................................... 24
How to recall sonarimages.......................................................................... 25
How to keep sonarimages........................................................................... 26
How to delete sonarimages......................................................................... 26
How to renamesonar images....................................................................... 26
How to print sonar images........................................................................... 27
How to burn sonarimages on a CD .............................................................. 27
302656/A 3
Simrad SH40
Automatic search and tracking procedures ............................................................28
How to start the horizontal search program ................................................... 28
How to start the vertical search program....................................................... 29
How to enable position track ....................................................................... 29
How to enable target track........................................................................... 30
How to add a target tracking line..................................................................30
BASIC THEORY................................................................ 31
Settings...................................................................................................................31
TVG..........................................................................................................31
PP Filter..................................................................................................... 32
Pulse formandlength..................................................................................32
Gain ........................................................................................................... 32
Tilt............................................................................................................. 33
Noise and reverberation..........................................................................................33
Cavitation................................................................................................... 34
Reverberation ............................................................................................. 34
Blocking.................................................................................................... 35
Check the noise yourself!............................................................................ 35
Layers and deflections............................................................................................36
Temperature and salinity layers....................................................................36
Deflections................................................................................................. 36
4
302656/A
Introduction
INTRODUCTION
The purpose of this booklet is to give you a short introduction to
the operational use of the SH40 sonar. It is not possible to explain
all the functionality and possibilities in detail, it is therefore
important that you familiarize yourself with the operator manual
provided with the sonar.
Know your sonar!
Your SH40 sonar is a large and expensive instrument. It is still
relatively easy to operate once you get to know the menus and
buttons. The sonar comprises the following units:
• A colour display monitor
• A computer
• A control panel
• A transmitter- and receiver unit
• A hull unit with a transducer array
In this publication we will focus on the basic use of the display
and control panel.
Click “Help”!
Installed on your SH40 sonar you will also find a comprehensive
on-line help system. You may not be able to find your language,
but everything written in the SH40 Operator manual is also
available on the sonar display. When you click the
Help button
you will first see a small help text in a window below the menu.
In this window you can click
Free to open the complete manual.
To close the manual, click the
Free button at the lower left side of
the large window.
But remember: When you open the complete on-line help
manual, it will place itself on the top of the sonar picture!
302656/A 5
Simrad SH40
IMPORTANT MATTERS
As with all advanced instruments, there are a few important
matters about the SH40 that you must remember.
Before you switch on the sonar
When you power up the sonar, the transducer is lowered down
below the vessel’s hull. Make sure that you have sufficient water
depth before you do this!
Whenthesonarisnotinuse
To protect the sonar when it is not in use, we strongly advice you
to hoist the transducer, even though you may not switch off the
power. In narrow or shallow waters this is very important, since
you may - in worst case - run the transducer into the bottom.
This will damage the transducer and the transducer shaft, and
extensive repair is required.
When you dock the vessel
It is very important that the sonar system remains switched off
when the vessel is in dry dock. If the transducer is subjected
to transmit power when it is in open air, it will be damaged.
As a safeguarding measure, you can remove the power fuses
on the sonar system before the vessel is docked. As an extra
safeguarding measure, the sonar is by default powered up with
the transmit power switched off.
If something breaks down
If you think that something has been damaged on the sonar,
contact your local dealer for advice.
6
302656/A
Releases
RELEASES
The SH40 sonar is based on advanced software. We are
continuously improving our products, and for this reason the
sonar software is upgraded. New software versions will in most
cases provide you with new functionality. To find out which
software your sonar uses, click the
System tab, then click Test in
the menu, and finally
About.
SH40 Release history
SW 1.3.X
New feature Noise filter implementedontheHorizontal menu.
The new filter will remove impulsive noise like cavitating
propellers and interfering noise from other sonars and echo
sounders.
New transmission beamforming greatly enhances the sonar
performance.
Improved performance when the sonar beam is tilted.
Added interface for third-party current profiler.
Improved software installation.
SW 1.2.X
This is the first software version for the SH40 sonar.
302656/A 7
Simrad SH40
POWER ON/OFF
This chapter explains how to switch your sonar system on and off.
WARNING
Before you start: Make sure that the water
depth below the keel is sufficient to lower the
transducer!
Howtoswitchonthesonar
Observe the following procedure.
Middle
Up
Down
MAIN SW.
POWER
A
B
C
D
(CD015022B)
1 Press the Power button on the colour display monitor.
2 Press the
Power button (A) on the Sonar Control Panel, and
keep it depressed for approximately two seconds.
• A green lamp w ill flash to indicated that the power has
been switched on, and that the computer is starting up.
After a short period (approximately 2 minutes) you will
see the sonar picture on the display.
3 Press the
Down button (D) on the control panel to lower
the transducer.
• The transducer will stop automatically when it has
been lowered to its full length. The dialogue at the
bottom right corner of the display will tell you when the
transducer has been fully lowered.
• By default the transmit power is disabled when the sonar
is powered up. This is for safety reasons. In the menu,
you will see that the
Transmit power button flashes to
remind you of this.
4 Set
Transmit power to On.
8 302656/A
Power on/off
How to switch off the sonar
Observe the following procedure.
Middle
Up
Down
MAIN SW.
POWER
A
B
C
D
(CD015022B)
1 Press the Up button (B) on the Sonar Control Panel.
• The transducer will automatically be hoisted, and it will
stop when it has been fully retracted. The dialogue at
the bottom right corner of the display will tell you whe
n
the transducer has been fully retracted.
2 Press the
Power button (A) on the Sonar Control Panel,
and
keep it depressed for approximately two seconds.
• The sonar is switched off. Note that you must N
OT
use the on/off switch on the computer, only t
his
Power
button on the Sonar Control Panel.
3 Switch off the display monitor.
If the sonar is switched off by mistake befo
re the transducer has
be hoisted, or you have problems with
the electrical power, you
can also hoist the transducer manu
ally.
302656/A 9
Simrad SH40
SONAR CONTROL PANEL
The sonar control panel is organized into fields. The buttons
within each field control a specific function on the sonar.
(CD015022A)
POWER
Up
Middle
Down
MAIN SW.
SYMBOL
Gain
H-
Range
H-
Gain
V-
Range
V-
Gain
H+
Range
H+
Gain
V+
Range
V+
MODE
Mode
1
GAIN
Mode
2
Mode
3
Mode
4
RANGE
CURSOR
Select
Menu
View
Object
SONAR OPERATING PANEL
TILT
Manual
Auto
VARIOUS
Zoom
Record
Off
Centre
Position
Track
Manual
Target
Track
Auto
Search
TRAIN
SIMRAD
Main switch
This is the sonar’s “on/off” switch. It has been previously
explained.
SYMBOL
(CD015022C)
A
B
C
D
Symbol
These buttons allow you to enter four different markers on the
sonar picture;
Target marker (A), Own ship (B) and Circle marker
(C). The markers will be placed at the cursor’s location when you
press the button. Every marker is identified with a number. You
can study and remove the markers if you click the
Marker tab.
The last button (D) is used to deploy a seine or trawl symbol.
10
302656/A
Loading...