Simpson H335, H340, H345 Data Sheet

• All parameters set from easy to understand front panel access
• One, two or four 5-amp relays optional
• Five user-selectable brightness levels
• 1/8 DIN, shallow depth case, 3.24”
• RS485 digital communications optional (H345)
• 12 or 24 DCV power supply output optional
• 4-20mA or 0-10 DCV analog transmission
• NEMA 4X rated front panel
Specications
7-segment, red LED 4 or 5 5 user-selectable levels
0.56" (14.2mm) 4 or 5 position, user programmable Display flashes “EEEEE” indicating Maximum Value Exceeded Display flashes “-EEEE” indicating Minimum Value Exceeded 4 LED indicators for up to four independ­ent setpoints
120, 85-250 VAC @ 10VA
9-36 DCV @ 10VA
0 to 50°C
-10 to +60°C <80% 25°C 100 ppm/°C 10 minutes
60 dB @ 50-60 Hz 70 dB @ 50-60 Hz
Successive approximation with oversampling 10 conversions per second User programmable 1-420 updates/min (240 default)
3.9" x 2.0" x 0.52” (99.8mm x 51.9mm x 13.2 mm)
3.24" (82.3 mm)
3.62" x 1.77" (92 mm x 45mm) 10 oz (283.5g) NEMA 4X Rated front panel
DISPLAY Type Quantity Brightness Height Decimal point Overrange indication
Underrange indication
Alarm Indicators
POWER REQUIREMENTS AC DC
ACCURACY @ 25°C as % of rdg DC Current High (5A, 2A) All Others DC Volts High (600 V) All others Resistance All ranges *AC Current High (2A, 5A) All others *AC Volts High (600V) All others
ENVIRONMENTAL
A TO D CONVERSION
MECHANICAL
0.2% ± 1 count
0.05% ± 1 count
0.1% ± 1 count
0.05% ± 1 count
0.1% ± 2 counts
0.2% ± 2 counts
0.1% ± 2 counts
0.1% ± 1 count
0.05% ± 1 count
0.3% ± 1 count
0.1% ± 1 count
0.2% ± 1 count
0.1% ± 1 count
0.1% ± 2 counts
0.3% ± 2 counts
0.2% ± 2 counts
0.2% ± 1 count
0.1% ± 1 count
* AC functions measured at 50 Hz, include ± 1 count for each additional
100 Hz above 50 Hz
more >>
For more information, visit www.simpsonelectric.com
ISOLATION
250V RMS MAX
Operating Temperature Storage Temperature Relative Humidity Ambient Temperature Temperature Drift
Warmup Time Noise Rejection
NMRR CMRR
Technique Sample Rate
Display Rate
Bezel Depth Panel Cutout Weight
Cover
4-1/2 digit
3-1/2 digit
HHaawwkk 33 IInnddiiccaattoorrss ccaann bbee ccoonnffiigguurreedd bbyy mmaakkiinngg aann eennttrryy iinnttoo eeaacchh sseeccttiioonn.. EExxaammppllee:: HH333355-33-7711-00-44-11
Basic Unit Power Supply Function/Range Output Signal 5A Relay Excitation
Basic Unit
3-1/2 digit, Red LED 4-1/2 digit, Red LED
Power Supply
Function/Range
Continued on next column
Ordering Information
1 2 3 4
81 82 83 84
0 1 2 6
0 1 2 4
0 1 2
71 72
51 52 53 54 55
H335 H345
11 12 13 14 15
21 22 23 24 25 26
61 62 63 64 65 66
41 42 43 44 45 46
31 32 33 34 35
* Awaiting UL approval
Selection Description
Selection Description
Function/Range continued
120 ACV (3-1/2 only) 85-250 ACV (4-1/2 only) 9-36 DCV 85-250 ACV (3-1/2 only)
200 DCmv 2 DCV 20 DCV 200 DCV 600 DCV*
200 DCµA 2 DCmA 20 DCmA 200 DCmA 2 DCA 5 DCA
200 ACmV 2 ACV 20 ACV 200 ACV 600 ACV*
200 ACµA 2 ACmA 20 ACmA 200 ACmA 2 ACA 5 ACA
200 ACmV TRMS
2 ACV TRMS 20 ACV TRMS 200 ACV TRMS 600 ACV* TRMS
200 ACµA TRMS 2 ACmA TRMS 20 ACmA TRMS 200 ACmA TRMS 2 ACA TRMS 5 ACA TRMS
4-20 DCmA Process 0-10 DCV Process
200 Ohm 2K Ohm 20K Ohm 200K Ohm
None 4-20 DCmA 0-10 DCV RS-485 (4-1/2 only)
None One Two Four
None 12 DCV 24 DCV
Output
5A Relays
Excitation
For more information, visit www.simpsonelectric.com
Installation and Panel Cutout - H335, H340, H345
Engineering Label Placement
To replace the engineering unit label, place the tip of a ballpoint pen into the small hole at the base of the engineering label in the bezel. Slide the label up until it pops out. Grasp and remove. Slide the new label half the distance in, then use the ballpoint pen to slide it into place.
Mounting Requirements
The Hawk 3 Advanced Digital Controller 1/8 DIN meters require a panel cutout of 1.77” (45mm) high and 3.62” (92 mm wide). To install the Hawk 3 meter into the panel cutout, remove the clips from the side of the meter. Slide the meter through the panel cutout, then slide the mounting clips back on the meter. Press evenly to ensure a proper fit. Tighten screws.
5DCV
5DCV 300DCV 300DCV
1K DCV
DC Voltage
4.5 mA DC
45mA DC
200mA DC
600mA DC
5.5A DC
5.5A DC
DC Current
200mV 5DCV
5DCV 300DCV 300DCV
1K DCV
AC Voltage
4.5 mA DC 45mA DC
200mA DC 600mA DC
5.5A DC
5.5A DC
AC Current
Range Resolution Resolution Input Overload
4.5 3.5 Impedance
200 10m
.1
1.2K 5DCV
2K
.1 1 12K 5DCV
20K 1 10
121K
5DCV
200K
10
100
1.2M
5DCV
Resistance
Inputs
For more information, visit www.simpsonelectric.com
3.59”
.52”
3.93”
2.04”
1.77”
3.62”
3.24”
1.75”
3.5
1 mV
.1 mV
1 V
3.5
1 V
Input
Impedance
1 M 1 M
1 M 1 M
Input
Impedance
1 M 1 M 1 M
Resolution
Resolution
Range
4.5
10 µV .1 mV
200 mV
.1mV
20 V 200 V 600 V
2 V
1 mV
10 mV
.1 V
10 mV 1 M
Range
20 V 200 V 600 V
Resolution
4.5
10uV .1mV 1 mV 200K2 V
1mV
10 mV
.1 V
Resolution
.1 mV 200K
10 mV
.1 V
Overload
Resolution
Range
4.5
200µA
10 nA
2 mA .1 µA
20 mA
1 µA
10 µA .1 mA
200 mA
.1 mA
2 A
.1 mA
5 A
Resolution
3.5
Impedance
.1 µA
1 µA
10 µA 10
1 mA
1 mA
Input
1K
100
.013 .013
1
Overload
Range
200µA
2 mA
20 mA
200 mA 10 µA
Overload
Resolution
4.5
3.5
.1 µA
.1 µA
1 µA
1 µA
10 µA 10
.1 mA 1 2 A 5 A
10 nA
.1 mA 1 mA .1 mA 1 mA
InputResolution
Impedance
Overload
1K
100
.013 .013
06/20/2011
Loading...