Sima Products SDW-150 User Manual
Oakmont, PA 15139
Bldg # 5
Register your product at www.simaproducts.com
140 Pennsylvania Ave
Sima Products Corporation
User Manual SDW-150 Wireless Microphone
©2008 Sima Products Corporation. Made in Taiwan. PN 21780
may also have other rights which vary from state to state.
may not apply to you. This warranty gives you specic legal rights, and you
incidental or consequential damages, so the above limitation or exclusion
any other liabilities. Some states do not allow the exclusion or limitation of
this product. Sima neither assumes nor authorizes anyone to assume for it
Sima’s liability for damages in no event shall exceed the amount paid for
warranty, even if Sima has been advised of the possibility of such damages.
arising out of contract, negligence, tort or under any
damages arising from the use of, or the inability to use, this product, whether
or anticipated benets, or other incidental, consequential, special or punitive
Sima shall have no liability for any damages due to lost prots, loss of use
Limitation of Liability and Remedies
return authorization number.
It is recommended that you call Sima at the number listed above to obtain a
Oakmont, PA 15139
Bldg. #5
140 Pennsylvania Ave.
Attn: Customer Service
Sima Products Corp.
of sale and this limited Warranty statement as proof of warranty coverage to:
You must deliver, mail or ship the product, together with both the original bill
What you must do to enforce Warranty:
made).
either repair or replace same without charge (but no cash refund will be
within 90 days from the original retail purchase, Sima will, at Sima’s option,
proves to be defective to the original purchaser in material or workmanship
Sima Products Corp. (“Sima”) warrants that is the accompanying product
Limited Warranty
Sima Products Corporation
90 Day Limited Warranty
Congratulations on your purchase of Sima’s new Wireless
Microphone, Model SDW-150. This high quality electret
condenser microphone is designed to connect to a
transmitting unit which transmits wirelessly to a receiving unit
that can be connected to your camcorder.
This package contains:
SDW-150 microphone with windscreen
1.
Transmitter unit
2.
Receiver unit
3.
Tie clip
4.
User manual
5.
Warnings and Cautions
FCC Part 15 - Class B digital device
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and,
if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
You are cautioned that changes or modications not expressly approved by the
party responsible for compliance could void your authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference and (2)
this device must accept any interference received, including interference that may
cause undesired operation
FCC RF Radiation Exposure Statement:
1. This Transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
2. This equipment complies with FCC RF radiation exposure limits set forth for an
uncontrolled environment. This device was tested for typical lap held operations with
the device contacted directly to the human body to the back side of the notebook
computer. To maintain compliance with FCC RF exposure compliance requirements,
avoid direct contact to the transmitting antenna during transmitting.
Battery Installation
To install batteries in the transmitter:
Slide open the battery door cover.
1.
Insert 2 AA batteries in the battery
2.
compartment as shown at right. Be
sure to follow the polarity markings
indicated in the compartment.
Replace battery door
3.
Low battery
The LED of each unit will ash frequently when power is at a low level. Please
change batteries for the units as needed. The transmitting range will be reduced
when the battery power is low.
To install batteries in the receiver:
Slide open the battery door cover.
1.
Insert 2 AAA batteries in the battery
2.
compartment as shown at right. Be
sure to follow the polarity markings
indicated in the compartment.
Replace battery door
3.
Operation of SDW-150 Wireless Digital Microphone
System link:
When using the SDW-150 for the rst time, you must establish a communications link between
the transmitter and receiver. Before starting, make sure each unit has batteries.
1.
Set the POWER switch to the ON position on both the transmitter and receiver units.
The “STATE” LED of both the transmitter and receiver will light up and ash while the two
units link together. When the system links successfully, the light will then remain on steady.
The next time you use the SDW-150, the system will link automatically. Note: If the receiver is
out of range, the LED will ash slowly to indicate loss of signal. Bring the receiver closer to the
transmitter, and push the LINK button until the LED remains steady.
Step 1
Operation:
After linking the system as described above:
Attach the receiver unit to your camcorder by sliding the adjustable shoe mount
1.
on the receiver unit into the camcorder’s hot shoe. Tighten to secure.
Connect the audio jack of the receiver unit into the mic input of the camcorder.
2.
Slide the POWER switch on the receiver unit to the ON position as shown above.
Insert the microphone jack into the mic jack on the transmitter unit. Slide the
3.
POWER switch to the ON position as shown above.
Attach the tie clip to the mic and locate the mic where desired.
Specications:
Electronic Condenser microphone
Frequency response: 100 – 10KHz
Sound quality: 22KHz mono channel
Impedance: 1.5K Ohm, 30% unbalanced
Effective output level: -50dB +/- 5dB unbalanced
Power requirement:
Receiver: AAA x 2pcs
Transmitter: AA x 2pcs
Power Consumption: 60mA (both transmitter and receiver)
Runtime: 12 to 15 hrs - transmitter
4 to 5 hrs - receiver
Effective range - 30 to 40 feet
Note: The LED indicators located on the transmitter
and receiver units perform 3 functions.
1.
2.
3.
Step 1
Step 2
Step 3
Communications link is intact (steady)
Low battery power (ashing quickly)
Out of range (ashing slowly)
Loading...