Page 1
Flex ATX SERIES
SST-FX350-G
The reference Flex ATX power supply
Support standard Flex ATX form factor
350W continuous power output at 40℃ operating temperature rated for 24/7 operation
High efficiency with 80 PLUS Gold certification
Class-leading single +12V rail
Support PCIe 6pin connector
Active PFC
Page 2
SPECIFICATION
Flex ATX Form Factor
SST-FX350-G
350W Switching Power Supply
1.0 INPUT:
1.1 VOLTAGE
MINIMUM NOMINAL MAXIMUM UNITS
90 100~240 264 Vrms
1.2 FREQUENCY
47Hz ~ 63Hz
1.3 CURRENT
115Vac / 5A max. 230Vac / 2.5A max.
With Active PFC
80Plus Gold
1.4 INRUSH CURRENT
No damage
01
Page 3
1.5 POWER EFFICIENCY
MEET 80 Plus Bronze at 115/230Vac input.
LOAD 5V 3.3V +12V -12V +5VSB SPEC
20% 1.53A 1.86A 4.48A 0.05A 0.38A 87%
50% 3.83A 4.66A 11.19A 0.12A 0.96A 90%
100% 7.67A 9.31A 22.38A 0.23A 1.92A 87%
In order to meet Eup* requirements the following quidance must be
met for the 5Vsb efficiency at 230V AC.
Load on 5Vsb 2013 Efficiency
< 45mA AC input power should be <0.5W, including no load
45mA ≥ 50%
100mA ≥ 55%
250mA ≥ 65%
≥ 1A ≥ 75%
1.6 LEAKAGE CURRENT
3.5mA max.
1.7 POWER FACTOR
PF>0.9 at 115/230Vac Full Load
2.0 OUTPUT:
+5V +3.3V +12V -12V +5Vsb
14.0A 17.0A 29.17A 0.3A 2.5A
0.A 0 A 0A 0.0A 0.0A
-- -- -- -- --
+3,-3% +3,-3% +3,-3% +10,-10% +5,-5%
50mV 50mV 120mV 120mV 50mV
＊
＊
＊
Voltage
Max load
Min load
Peak load
Regulation
Ripple & Noise
02
Page 4
＊ The continuous total output power is 350W max.
• The combined power of +5V and +3.3V is 90W max.
＊ Add 0.1uF and 10uF capacitors across output terminal during ripple & noise test.
＊ LOAD REGULATION TEST TABLE:
+5V +3.3V +12V -12V +5Vsb
LOAD1 0.0A 0.0A 0.5A 0.0A 0.0A
LOAD2 5.0A 5.0A 0.0A 0.0A 0.0A
LOAD3 1.53A 1.86A 4.48A 0.05A 0.38A
LOAD4 3.83A 4.66A 11.19A 0.12A 0.96A
LOAD5 7.67A 9.31A 22.38A 0.23A 1.92A
LOAD6 0.0A 0.0A 29.17A 0.0A 0.0A
LOAD7 14.0A 6.0A 20.34A 0.3A 2.5A
LOAD8 6.76A 17.0A 20.34A 0.3A 2.5A
2.1 REMOTE ON/OFF
TTL High/PS-OFF; TTL Low/PS-ON
VIL=0.8Vmax, IIL=-1.6mAmax @Vin=0.4V
VIH=2.0Vmin @Iin=-200uA, VIH=5.25Vmax @open ckt.
2.2 HOLD-UP TIME
10msec (minimum) at 75% of full load at 230/115Vac input.
2.3 POWER GOOD SIGNAL
Singal type +5V TTL compatible.
power good max ripple & noise 400mV pk-pk.
2.4 POWER GOOD
Power good delay time 100-500 msec.
2.5 POWER FAIL DELAY
>1 msec.
03
Page 5
2.6 TURN-ON DELAY TIME
2000 msec max.At nominal line full load.
2.7 TRANSIENT OVERSHOOT
+/-10% max with 30% load change(+12V 40% load chang) on all outputs are
100% of the rated.
Load slew rated 1A/uS and capacitive load as below :
+5V +3.3V +12V -12V +5Vsb
10000uF 10000uF 10000uF 330uF 10000uF
2.8 RISE TIME
20ms max at full load.
2.9 TIMING WAVEFORMS
T1:Power Turn On Time
T2:Rise Time of the +12V/+5V/+3.3V Output
T3:Pwr_OK Delay
T4: Pwr_OK Rise Time
T5:AC loss to Pwr_OK Hold Up Time
T6:Power_Fail Warning Time
04
Page 6
3.0 PROTECTION
When OPP, OVP,OTP or short protection is triggered, the main outputs will be
latched off. The main outputs can be reset by cycling the DC remote on/off or
AC power. +5Vsb output is auto recovery when fault condition removed.
3.1 OVER POWER PROTECTION
Foldback at 115%~150% over peak load
3.2 OVER VOLTAGE PROTECTION
+3.3V output 5.2 Vmax.
+5.0V output 7.0 Vmax.
+12.0V output 16 Vmax.
3.3 SHORT PROTECTION
All output to GND.
4.0 ENVIRONMENT:
4.1 OPERATING TEMP. 0 ºC to +40 ºC
4.2 STORAGE TEMP. -20 ºC to +70 ºC
4.3 OPERATING HUMIDITY 20% to 90%,non-condensing
4.4 STORAGE HUMIDITY 5% to 95%, non-condensing
4.5 OPERATING ALTITUDE 0 to 10,000 feet
4.6 STORAGE ALTITUDE 0 to 50,000 feet
5.0 HI-POT:(Input/Output isolation)
5.1 PRIMARY TO SECONDARY
3535Vdc for 3 seconds
5.2 INSULATION RESISTANCE
3535Vdc for 3 seconds
05
Page 7
6.0 CE REQUIREMENTS
6.1 CONDUCTED EMI
1. MEET FCC： Class B
2. MEET CISPR 22： Class B
3. MEET BSMI： Class B
6.2 SAFETY STANDARDS
1. MEET CUL (UL 60950)
2. MEET TUV EN60950
3. MEET CB (IEC 60950 )
4. MEET CE
5. MEET CCC
6.3 HARMONIC
MEET IEC1000-3-2,Class D
7.0 MTBF at 25
100K hrs minimum
ºC(demonstrated)
8.0 DIMENSIONS
LxWxH=150 mm x 81.5 mm x 40.5 mm
06
Page 8
G11233050
Loading...