Users Manual
Hi-SpecTM 1600W Chainsaw
Product Code 112113
© September 2006
• This guarantee becomes effective at the date of retail purchase.
PLEASE KEEP YOUR RECEIPT.
• If this product develops a fault within 30 days of purchase, return it to the
stockist where it was purchased, with your receipt, stating details of the fault.
You will receive a replacement or refund.
• If this product develops a fault within 3 years of purchase return it to;
Silverline Tools Service Centre
PO Box 2988
Yeovil
BA21 1WU
Include your original receipt, details of the fault, your name and address, place and
date of purchase. We do not refund carriage. All product should be in a suitably
clean and safe state for repair, and should be packaged carefully to prevent damage
or injury during transportation. We may reject unsuitable or unsafe deliveries.
• You must provide proof of purchase before any work can be carried out.
• All work will be carried out by Silverline Tools or its authorised repair agents.
• Any parts which are replaced will become the property of Silverline Tools.
• The repair or replacement of the product will not extend the period of guarantee.
• The repair or replacement of your product under guarantee provides benefits which
are additional to and do not affect your statutory rights as a consumer.
What is covered:
• The repair of the product, if found to be defective due to faulty materials or workmanship
within 3 years of purchase. If any part is no longer available or out of manufacture,
Silverline Tools will replace it with a functional replacement part.
• Use of the product in the UK.
What is not covered:
Silverline Tools does not guarantee repairs required as a result of:
• Normal wear and tear Eg blades, brushes, belts, bulbs, batteries etc.
• Accidental damage, faults caused by negligent use or care,
misuse, neglect, careless operation or handling of the product.
• Use of the product for anything other than normal domestic purposes.
• Change or modification of the product in any way.
• Use of parts and accessories which are not Silverline Tools genuine components.
• Faulty installation (except installed by Silverline Tools).
• Repairs or alterations carried out by parties other than
Silverline Tools or its authorised repair agents.
Silverline Tools 3 Year Guarantee
Thankyou for choosing this product
Product Familiarisation
Hi-SpecTM 1600W Chainsaw
1. Protection guard
2. Chain
3. Guide bar
4. Switch
5. Oil cap
6. Chain oil flow control
7. Oil level indicator
WARNING: - THIS MACHINE CAN CAUSE DEATH OR
SERIOUS INJURY. FOLLOW THE SAFETY INSTRUCTIONS IN
THIS BOOKLET AT ALL TIMES
ALWAYS WEAR THE CORRECT PERSONAL PROTECTIVE
EQUIPMENT FOR THIS PRODUCT. MAKE SURE BEFORE
USE THAT ALL PROTECTIVE EQUIPMENT IS IN A GOOD
WORKING ORDER AND FREE OF ANY DEFECTS.
ADDITIONAL SAFETY INSTRUCTIONS FOR HI-SPEC
TM
CHAIN SAW
• Before using this saw, familiarise yourself with all its controls
and how to use it correctly prior to use.
• If using this saw outside only use extension reels and cables
suitable for outdoor use.
• This tool must never be left unattended.
• Keep out of the reach of children at all times.
• Never attempt to use this saw if it is not fully equipped, or if it
has been subject to any unauthorised modifications.
SPECIFICATION
Motor:
1600W
Input power:
230V/50Hz
Weight:
6.5kgs
No load speed:
660m/min
Guide bar length:
405mm
Chain: Orgeon
®
Extra Guard3/8"*
*Orgeon
®
is a registered trademark of Blount International Inc
• Never use this machine when other people are in close vicinity.
• Always ensure that when using this chain saw you are on a safe
stable surface and in a safe working position.
• Do not use this product if the chain is broken or excessively
worn.
• This machine should be firmly held in both hands at all times.
• Always be aware of the rotating blade and the direction you are
cutting in.
• Beware of rebounds/kickback.
• The chain saw must be unplugged before moving it from one
location to another, when cleaning it, before carrying out any
maintenance and before putting it away.
• Do not attempt to repair this machine.
• When carrying the chain saw always make sure that it is held
by the front handle with the chain directed backwards. The
protective guard is in place. Never carry this product by the
power cable.
Weight vibration:
5.71m/s
2
Sound pressure: 98dB
Sound power: 112dB
Double insulated:
Fuse rating:
13A
1
2
3
6
5
4
Introduction
Carefully read and understand this manual and any label attached
to the tool before use. Keep these instructions with the product for
future reference. Ensure all persons who use and service this
product are acquainted with this manual.
Electrical Safety Information
• The wires in this product are coloured:
Blue Neutral (N)
Brown Live (L)
Green & Yellow Earth (E)
• As the colours may not correspond with the coloured markings
identifying the terminals in your plug, proceed as follows.
• The wire which is coloured blue must be connected to the
terminal which is marked with the letter N or coloured black, the
wire which is coloured brown must be connected to the terminal
which is marked L or coloured red.
• This appliance must be protected by a suitable fuse.
• To prevent fire or shock hazard, do not expose this product to
rain/water or moisture. There are no user serviceable parts inside
except those referred to in this manual. Always refer servicing to
qualified service personnel. Never remove any part of the casing
unless qualified to do so; this unit contains dangerous voltages.
• Use of a residual current device (RCD) will reduce the risk of
electric shock.
NEVER CONNECT THE BROWN OR BLUE WIRE TO THE
EARTH PIN OF THE 13 AMP PLUG. IF IN DOUBT CONSULT A
QUALIFIED ELECTRICIAN
General Safety Instructions
Even when used as prescribed it is not possible to eliminate all
residual risk factors. Use with caution.
Keep guards in position
• Always keep guards in position, in good working order, correctly
adjusted and aligned. Never attempt to use a power tool without
any guard supplied with it.
Remove adjusting keys
• Always check to see that keys and adjusting wrenches are
removed from power tool before turning on.
Clean work area
• Accidents occur where benches and work areas are cluttered
or dirty, floors must be kept clear, avoid working where the floor is
slippery.
Dangerous environment
• Do not use power tools in damp or wet conditions, or expose
them to rain. Provide adequate surrounding work space and keep
area well lit. Do not use power tools where there is a risk of
explosion or fire from combustible material, flammable liquids,
flammable gases or dust of an explosive nature. When using
power tools avoid contact with any earthed items such as pipes,
radiators, cookers, refrigerators, metal baths and taps.
Children & pets
• Children and pets should always be kept at a safe distance
from
your workshop child-proof. Lock tool away where children can't get
access to them. Remove batteries from cordless tools.
Use the correct power tool
• Don't force, or attempt to use a power tool for a purpose it was
not designed for. Do not use a small tool to do the job of a heavy
duty tool.
Wear correct clothing and footwear.
• Don't wear loose clothing, neckties or jewellery or other items
which may get caught in moving parts. Wear non-slip footwear,
cover or tie back long hair. Use safety footwear if necessary.
Protect your head
• Wear safety goggles at all times, every day glasses are not
sufficient for eye protection, as lenses are not impact resistant
and could shatter. Use an approved face or dust mask when
operation creates dust. Ensure dust extraction equipment is
functioning and correctly used. Hearing protection should be used
if the sound intensity level for the operator could exceed 85dB(A).
Use a hard hat where there is a risk of falling objects or striking
your head on low level obstructions.
Protect yourself from vibration.
• Hand held power tools may produce vibration. Vibration can
cause disease. Gloves to keep the operator warm and dry and
therefore maintain good blood circulation in the fingers may help.
This tool has not been designed for extended or industrial
operation.
Secure work
• Always secure work. Where practical use a clamp or vice, it will
allow you to use both hands to operate your power tool.
Keep your balance
• Don't over reach, keep proper footing at all times to ensure
correct balance.
Maintain your power tool
• Keep your power tool in good working order, keep tools sharp and
clean for best and safest performance. Ensure ventilation holes
are kept clean and unrestricted at all times.
Always disconnect.
• Before changing tools, always ensure they are disconnected from
the power source.
Accessories
• The use of any attachment or accessory other than those
mentioned in this manual could result in damage or injury. The
use of improper accessories could be dangerous.
Never stand on your power tool
• Standing on your power tool or its stand could cause serious
injury if the tool is tipped or if the cutting tool is accidentally
contacted. Do not store materials above or near the tool so that it
is necessary to stand on the tool or its stand to reach them.
Switch off before connecting.
• Ensure the power tool is switched off before connecting to the
power source. If the power tool stops unexpectedly turn the power
switch to off.
Do not abuse the power cord.
• Be sure your cable/extension cable is properly wired and in good
condition. Always replace a damaged cable/extension cable or
have it repaired by a qualified person before using it. Never yank
or pull the cable to disconnect it from the power socket. Never
carry your power tool by it’s cable. Keep the cable away from
damp, heat, oil, solvents, and sharp edges.
Check for damaged or missing parts
.
• Before each use check if any part of the power tool is damaged or
missing, check carefully that it will operate properly and perform
its intended function. Check alignment of moving parts for binding.
Any guard or other part that is damaged should be correctly
repaired or replaced. Do not use if the power switch does not turn
the power on and off. Check any other condition that may affect
the safety of the power tool. DO NOT USE IF DEFECTIVE.
Direction of feed
• Feed work into a blade or cutter against the direction of rotation of
the blade or cutter only.
Don’t leave the tool running unattended
• Always wait until your power tool has come to a complete stop
before leaving it and then disconnect from power source.
FUSE
BROWN
(Live)
BLUE
(Neutral)
E
L
N
FUSE
GREEN/YELLOW
OR GREEN
FUSE
BROWN
(Live)
BLUE
(Neutral)
E
L
N
FUSE
Double Insulated
Earthed
7
Loading...