Silverline Gasless Turbo Mig User Manual [en, de, es, fr, it]

3 Year Guarantee

*Register online within 30 days. Terms & Conditions apply

Garantie de 3 ans *Enregistrez votre produit en ligne dans les 30 jours. Sous réserve des Conditions Générales d’utilisation

3 Jahre Garantie *Registrieren Sie sich innerhalb von 30 Tagen online. Es gelten die allgemeinen Geschäftsbedingungen

3 años de garantía

*Regístrese online dentro de 30 días. Se aplican los términos y condiciones

3 anni di garanzia *Registrarsi on-line entro 30 giorni. Termini e Condizioni si applicano

3 Jaar Garantie *Registreer online binnen 30 dagen. Algemene voorwaarden van toepassing

www.silverlinetools.com

POWER

282562

50-90A

Gasless Turbo Mig

Gasless Turbo Mig Poste à souder Turbo MIG sans gaz Turbo-MIG-Fülldrahtschweißgerät

www.silverlinetools.com

Soldador sin gas Turbo Mig Macchina a saldatura Mig senza gas Gaslose MIG lasmachine

50-90A

Gasless Turbo Mig

English .................. 4

Français ................ 8

Deutsch ................. 12

Español ................. 16

Italiano .................. 20

Nederlands ............ 24

www.silverlinetools.com

Description of Symbols

The rating plate on your tool may show symbols. These represent important information about the product or instructions on its use.

Wear hearing protection Wear eye protection Wear breathing protection Wear head protection

Wear hand protection

Read instruction Manual

Class I construction (Protective earth)

Conforms to relevant legislation and safety standards

Environmental Protection

Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your local authority or retailer for recycling advice

Speciﬁcation

Voltage: ........................................................230V

Frequency: ...................................................50Hz

Rated duty cycle:..........................................10% @ 90A, 60% @ 50A

Current range: ..............................................50–90A

No load voltage: ...........................................26-30V

Insulation class: ...........................................H

Wire: ..........................................................0.9mm ﬂux cored wire

Max welding thickness:................................6.5mm

Fuse rating: ..................................................13A

Protection Class: ..........................................

The sound intensity level for the operator may exceed 85dB(A) and

As part of our ongoing product development, speciﬁcations of Silverline

sound protection measures are necessary.

products may alter without notice.

Carefully read and understand this manual and any label attached to the tool before use. Keep these instructions with the product for future reference. Ensure all persons who use this product are fully acquainted with this manual.

Even when used as prescribed it is not possible to eliminate all residual risk factors. Use with caution. If you are at all unsure of the correct and safe manner in which to use this tool, do not attempt to use it.

General Power Tool Safety Warnings

WARNING Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, ﬁre and/or serious injury.

Save all warnings and instructions for future reference.

The term "power tool" in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.

Work Area Safety

a) Keep work area clean and well lit. Cluttered or dark areas invite accidents b) Do not operate power tools in explosive atmospheres, such as in the

presence of ﬂammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes

c) Keep children and bystanders away while operating a power tool.

Distractions can cause you to lose control

Electrical Safety

a) See ‘Connecting to a Power Supply’ below for critical safety information

regarding connecting this tool to the mains electrical supply. Failure to

follow this guidance can result in a fatal accident

b) Avoid body contact with earthed or grounded surfaces, such as pipes,

radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded

c) Do not expose power tools to rain or wet conditions. Water entering a

power tool will increase the risk of electric shock

d) Do not abuse the cord. Never use the cord for carrying, pulling or

unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric

shock

e) When operating a power tool outdoors, use an extension cord suitable

for outdoor use. Use of a cord suitable for outdoor use reduces the risk of

electric shock

f) If operating a power tool in a damp location is unavoidable, use a

residual current device (RCD) protected supply. Use of an RCD reduces

the risk of electric shock

NOTE: The term “residual current device (RCD)” may be replaced by the term “ground fault circuit interrupter (GFCI)” or “earth leakage circuit breaker (ELCB)”.

Personal Safety

a) Stay alert, watch what you are doing and use common sense when

operating a power tool. Do not use a power tool while you are tired or under the inﬂuence of drugs, alcohol or medication. A moment of

inattention while operating power tools may result in serious personal injury

b) Use personal protective equipment. Always wear eye protection.

Protective equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries

c) Prevent unintentional starting. Ensure the switch is in the off-position

before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your ﬁnger on the switch or

energising power tools that have the switch on invites accidents

d) Remove any adjusting key or wrench before turning the power tool on.

A wrench or a key left attached to a rotating part of the power tool may result in personal injury

e) Do not overreach. Keep proper footing and balance at all times. This

enables better control of the power tool in unexpected situations

f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair,

clothing and gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts

g) If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use

of dust collection can reduce dust-related hazards

Power Tool Use & Care

a) Do not force the power tool. Use the correct power tool for your

application. The correct power tool will do the job better and safer at the

rate for which it was designed

b) Do not use the power tool if the switch does not turn it on and off. Any

power tool that cannot be controlled with the switch is dangerous and must be repaired

c) Disconnect the plug from the power source and/or the battery pack

from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures

reduce the risk of starting the power tool accidentally

Gasless Turbo Mig282562

d) Store idle power tools out of the reach of children and do not allow

persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users

e) Maintain power tools. Check for misalignment or binding of moving

parts, breakage of parts and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools

f) Keep cutting tools sharp and clean. Properly maintained cutting tools with

sharp cutting edges are less likely to bind and are easier to control

g) Use the power tool, accessories and tool bits etc. in accordance with

these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from

those intended could result in a hazardous situation

Service

a) Have your power tool serviced by a qualiﬁed repair person using only

identical replacement parts. This will ensure that the safety of the power

tool is maintained

Welding Safety

• Welding produces toxic fumes and can reduce oxygen levels in the work area

• Always work in a well-ventilated area. Avoid inhaling welding fumes, use a

suitable respirator where appropriate

• Some metal parts may have zinc, lead, cadmium or other coatings. Attempting to weld through these coatings can produce highly toxic fumes. Always remove all coatings before welding

• If you experience irritation to the lungs, throat or eyes whilst welding, STOP IMMEDIATELY and seek fresh air

• Welding produces extremely high levels of UV light. To prevent eye damage, ALWAYS wear an approved welding face mask. Under no circumstances look directly at the arc

• If there is a possibility of other people approaching the work area, erect suitable screening to protect them from the light / glare

• To prevent skin damage, ALWAYS wear a suitable ﬁre-proof long sleeved jacket, heat proof gloves, and cap. Keep covered up

• Always remove any ﬂammable materials (e.g. cigarette lighter, matches) from your clothing before welding

• Always keep a ﬁre extinguisher nearby when welding. Sparks and accidental contacts can cause ﬁres. Only weld when the work area and all workpieces are dry

• Do not weld sealed containers (e.g. fuel tanks, air tanks, oil drums). The heat generated from welding can cause sealed containers to burst without warning

• Be aware of transferred heat. Metal parts can conduct heat away from the work area and cause ignition of ﬂammable materials

• Be aware that welded parts will remain hot for some time after joining. Allow to cool completely before handling, or leaving unattended

• Never weld where ﬂammable gases, liquids or dust are present

• Ensure that there is always a responsible person nearby to alert you to any ﬁre,

or to call help in an emergency

• Use of welding machines will create powerful magnetic ﬁelds. This may disturb the operation of sensitive electronic equipment. Pacemaker wearers should consult a doctor before using a welding machine

• Do not overload power supply. Check that your mains wiring is capable of delivering the required currents safely (see speciﬁcation)

Wire feed

• Caution: The tip of welding wire can be very sharp, and is fed with adequate force to puncture skin

• Keep the welding machine switched off until you are ready to begin welding. Never point the torch towards people or animals

Product Familiarisation

1 Shroud

2 Trigger 3 Wire Speed Dial 4 Access Cover 5 Voltage Control Switches 6 Power Switch 7 Earth Cable & Clamp

Accessories

Wire Reel (0.9mm ﬂux cored) Welding Mask (inc. handle and visor) Spare Tips (x2) Hammer & Brush

Unpacking Your Tool

• Carefully unpack and inspect your tool. Fully familiarise yourself with all its features and functions

• Ensure that all parts of the tool are present and in good condition. If any parts are missing or damaged, have such parts replaced before attempting to use this tool

Assembly

Assembling the mask

1. Carefully slot the handle into the ﬁxing slots on the mask. Ensure both

nibs engage for a secure ﬁt

2. Remove protective wrapping from the visor and slot the visor into

place. Take care not to scratch the visor, and ensure the visor engages fully with the clips so that it fully covers the viewing panel and cannot be dislodged

Installing wire

1. Open the Access Cover (4) on the top of the machine

2. Carefully remove the spool locking knob, spring and washer

3. Slide the reel of welding wire (supplied) onto the spool spindle, positioning so

that the wire will feed off of the top of the spool into the drive rollers

4. Replace the washer, spring and spool locking knob, and tighten. Tighten

so that the reel of wire doesn’t unravel under its own spring tension and resistance is felt when the spool is rotated

5. Raise the roller clamp knob so that the guide roller can be swung clear

6. Carefully release the end of the wire from the spool, take care not to let the

wire unravel. Ensure that the wire tip is straight, and is cut off cleanly

7. Slowly feed the wire into the torch liner

8. Swing the guide roller back into position, ensuring that the wire is centred in

the grooves of the guide and drive rollers

9. Lower the drive roller clamp knob so that the guide roller is secured, and

tighten gently

10. Close the Access Cover (4)

11. Pull the Shroud (1) from the torch and unscrew the tip

12. Connect the machine to the mains power supply, switch on, and hold the torch

13. Move the torch away from the machine, so that the torch cable is straight

14. Ensure that the torch is not touching anything, and squeeze the Trigger (2). The machine should drive the wire through to the torch

15. If the wire is not driven through, disconnect from the mains power supply, open the access cover, and tighten the drive roller clamp knob. The drive rollers should be just tight enough to drive the wire through to the torch, but not so tight as to prevent the drive roller from slipping if the wire becomes blocked

16. When the wire is propelled out of the end of the torch, switch off and disconnect from the mains power supply

17. Reﬁt the tip and the shroud, and trim the wire so that approx 5mm projects from the tip

www.silverlinetools.com

Before Use

• Always wear appropriate personal protective equipment for the job that you are to do. Use of this machine requires a welding mask, gloves, heat resistant clothing, and if appropriate a respirator

• Always ensure that you have an appropriate ﬁre extinguisher near to the work area

• Always inspect your machine for damage or wear. Pay particular attention to leads and cables. If any damage is found DO NOT USE

• Check that all casings or covers are properly closed and secured

• Position the welder in such a way that it will not move or tip in use. Ensure

that there is at least 500mm of clear space around the welder to allow proper ventilation

Operating Instructions

WARNING: Always unplug the welding machine from the mains supply and allow to cool fully before attempting to ﬁt or replace any part.

Setting the machine

• To achieve a good quality weld, the Wire Speed Dial (3), and Voltage Control Switches (5) must be set correctly

• The two voltage control switches can be used to obtain 4 current settings:

- Lo + 1 = very low voltage suitable for thin sheet metal

- Lo + 2 = low voltage suitable for most sheet metal

- Hi + 1 = high voltage suitable for thick sheet metal

- Hi + 2 = very high voltage suitable for metal up to 5mm thick

• The wire speed should be adjusted to provide a steady arc. The correct setting will depend on distance, current, torch speed, and other factors. Experiment with wire speeds until you ﬁnd an optimum setting

Duty Cycle

• This machine is not designed to weld constantly. Excessive continuous welding would cause overheating and damage to internal components

• The duty cycle deﬁnes the number of minutes, in every ten minutes, that the machine can weld

• For a duty cycle of 10%, the machine may be used for 1 minute, and then must be allowed 9 minutes to cool

• If the duty cycle is exceeded, the machine will automatically cut-out

• Using the machine at reduced current settings, and maintaining good ventilation

will maximise the duty cycle

Thermal cut-out

• This machine is equipped with a thermal cut-out. If the machine is overloaded, or used beyond its duty cycle, it will automatically shut down

• Allow the machine to cool. The cut-out will automatically reset once the machine is ready to be used

Preparing to weld

• Ensure that parts to be joined are clean, and free from rust, paint, or other ﬁnishes

• All parts should be well supported, so that there is a gap of approximately 1mm where you intend to form the welded joint

• Check that there are no ﬂammable materials in the vicinity of the work area

• Attach the Earthing Clamp (7) to a cleaned area of one of the parts, as near as

practical to where the joint will be

• Ensure that there is both a responsible person and an operable ﬁre extinguisher at hand

• Connect the machine to the mains power supply

Welding

WARNING: Using a welder correctly is a technical skill. A welder used incorrectly

can be highly dangerous. The information presented below is general guidance only. If you are not entirely conﬁdent in your ability to use this tool safely DO NOT USE.

1. Move the Power Switch (6) to the ‘ON’ position

2. Hold the torch in one hand and the face mask in the other

3. Position the torch so that the tip is approx 10mm away from the metal, at an

angle of approx 75˚

4. Hold the mask over your face, and squeeze the Trigger (2)

5. An arc should strike between the metal, and the tip. Hold the trigger for 1-2

seconds and release

6. Allow the weld to cool slightly, and move the mask away from your face. If

the settings were correct, a round 'spot' weld should have formed

7. If the weld has not fully penetrated the metal, increase the voltage setting. If

a hole has been made in the metal, reduce the voltage setting

• Practice making 'spot' welds until you are conﬁdent using the machine, and selecting settings

• To form a 'seam' weld, hold the trigger for longer, and slowly move the torch forward at the same time

• If the machine settings are correct, the arc should be steady, and produce a crackling sound

• If you hear a popping sound, or struggle to maintain the arc, adjust the wire speed. If you feel the torch trying to 'push back', reduce the wire speed

• Creating neat, high quality, welds is a skill that takes time to master. Practice and good preparation should result in satisfactory welds

Maintenance

WARNING: Always unplug the welding machine from the mains supply and allow to cool fully before attempting to ﬁt or replace any part.

Replacing wire

This welder requires 0.9mm ﬂux cored wire

1. Use a pair of pliers to draw the last of the old wire out through the tip of the torch (if the old wire spool is not empty, cut the wire at the spool and release the drive roller clamp knob)

2. To access the welding wire, open the Access Cover (4) on the top of the machine

3. Remove the spool locking knob, spring and washer and the old wire spool; slide a fresh spool of welding wire onto the spool spindle

4. Replace the washer, spring and spool locking knob, and tighten. Tighten so that the reel of wire doesn’t unravel under its own spring tension and resistance is felt when the spool is rotated

5. Loosen and raise the drive roller clamp knob so that the guide roller can be swung clear

6. Carefully release the end of the wire from the spool, take care not to let the wire unravel. Ensure that the wire tip is straight, and is cut off cleanly

7. Slowly feed the wire into the torch liner

8. Lower the drive roller clamp knob so that the guide roller is secured, and tighten gently

9. Close the Access Cover (4)

Then proceed as per instructions for ‘Installing wire’ above

Replacing tips

• As the welder is used, the tip may become worn. This will make the arc difﬁcult to control

1. To replace the tip, pull the Shroud (1) from the torch, and unscrew the old tip

2. Check that the new tip is the correct size for the wire to be used

3. Thread the new tip over the end of the wire, and screw into the torch.

Replace the Shroud (1)

Cleaning

Disconnect the machine from the mains supply before cleaning

• Keep your machine clean. Always clean dust or particles away and never allow ventilation holes to become blocked

• Use a soft brush or dry cloth to clean the machine. If available, blow through the ventilation holes with clean, dry, compressed air

Silverline Tools Guarantee

This Silverline product comes with a 3 year guarantee

Register this product at silverlinetools.com within 30 days of purchase in order to qualify for the 3 year guarantee. Guarantee period begins according to the date of purchase on your sales receipt.

Terms & Conditions

Guarantee period becomes effective from the date of retail purchase as detailed on your sales receipt.

PLEASE KEEP YOUR SALES RECEIPT

If this product develops a fault within 30 days of purchase, return it to the stockiest where it was purchased, with your receipt, stating details of the fault. You will receive a replacement or refund.

If this product develops a fault after the 30 day period, return it to:

Silverline Tools Service Centre PO Box 2988 Yeovil BA21 1WU, UK

The guarantee claim must be submitted during the guarantee period. You must provide the original sales receipt indicating the purchase date,

your name, address and place of purchase before any work can be carried out.

You must provide precise details of the fault requiring correction. Claims made within the guarantee period will be veriﬁed by Silverline Tools

to establish if the deﬁciencies are related to material or manufacturing of the product.

Carriage will not be refunded. Items for return must be in a suitably clean and safe state for repair, and should be packaged carefully to prevent damage or injury during transportation. We may reject unsuitable or unsafe deliveries.

All work will be carried out by Silverline Tools or its authorized repair agents.

The repair or replacement of the product will not extend the period of guarantee

Defects recognised by us as being covered by the guarantee shall be corrected by means of repair of the tool, free of charge (excluding carriage charges) or by replacement with a tool in perfect working order.

Retained tools, or parts, for which a replacement has been issued, will become the property of Silverline Tools.

EC Declaration of Conformity

The undersigned: Mr Darrell Morris as authorised by: Silverline Tools

Declares that the

Product Code: 282562 Description: Gasless Turbo Mig

Conforms to the following Directives:

• Low Voltage Directive 2006/95/EC

• EMC Directive 2004/108/EC

• ROHS Directive 2002/95/EC

• EN 60974-10:2007

• EN 60974-10:2008

• EN 61000-3:2006+A2:2009

• EN 61000-3-11:2000

• EN 50445:2008

• EN 175:1997

Gasless Turbo Mig282562

Registering your purchase

Registration is made at silverlinetools.com by selecting the Guarantee Registration button. You will need to enter:-

• Your personal details

• Details of the product and purchase information

Once this information is entered your guarantee certiﬁcate will be created in PDF format for you to print out and keep with your purchase.

The repair or replacement of your product under guarantee provides beneﬁts which are additional to and do not affect your statutory rights as a consumer.

What is covered:

The repair of the product, if it can be veriﬁed to the satisfaction of Silverline Tools that the deﬁciencies were due to faulty materials or workmanship within the guarantee period.

If any part is no longer available or out of manufacture, Silverline Tools will replace it with a functional replacement part.

Use of this product in the EU.

What is not covered:

Silverline Tools does not guarantee repairs required as a result of: Normal wear and tear caused by use in accordance with the operating

instructions eg blades, brushes, belts, bulbs, batteries etc. The replacement of any provided accessories drill bits, blades, sanding

sheets, cutting discs and other related items. Accidental damage, faults caused by negligent use or care, misuse,

neglect, careless operation or handling of the product. Use of the product for anything other than normal domestic purposes. Change or modiﬁcation of the product in any way. Use of parts and accessories which are not genuine Silverline Tools

components. Faulty installation (except installed by Silverline Tools). Repairs or alterations carried out by parties other than Silverline Tools or its

authorized repair agents. Claims other than the right to correction of faults on the tool named in

these guarantee conditions are not covered by the guarantee.

The technical documentation is kept by: Silverline Tools

Notiﬁed body: TUV Rheinland

Place of declaration: Shanghai, China

Date: 17/09/12

Signed by:

Director

Name and address of Manufacturer or Authorised representative:

Silverline Tools, Boundary Way, Lufton Trading Estate, Yeovil, Somerset,

BA22 8HZ United Kingdom

www.silverlinetools.com

Description des symboles

La plaque signalétique ﬁgurant sur votre outil peut présenter des symboles. Ces symboles constituent des informations importantes relatives au produit ou des instructions concernant son utilisation.

Port de protection auditive Port de lunettes de sécurité Port de masque respiratoire Port du casque

Lire le manuel d’instructions

Construction de classe I (mise à la terre).

Conforme à la réglementation et aux normes de sécurité en vigueur

Protection de l’environnement Les produits électriques usagés ne doivent pas être jetés avec les ordures ménagères. Veuillez les recycler dans les centres prévus à cet effet. Pour de plus amples informations, veuillez contacter votre municipalité ou point de vente La plaque de valeur nominale sur votre outil peut afﬁcher des symboles.

Port de gants

Caractéristiques techniques

Tension : ...............................................230 V

Fréquence : ..........................................50 Hz

Cycle d’utilisation nominal : ..................10 % sous 90 A, 60 % sous 50 A

Intensité de soudage : ..........................50-90 A

Tension à vide : ....................................26-30 V

Classe d’isolation : ...............................H

Fil : .....................................................Fil fourré 0,9 mm

Épaisseur de soudage maximale : ........6,5 mm

Calibre du fusible : ...............................13 A

Classe de protection (Mise à la terre) : .

L’intensité sonore peut dépasser 85 dB(A) et il est recommandé que

l’opérateur prenne des mesures de protection sonore.

Du fait de l’évolution constante de notre développement produits, les caractéristiques des produits Silverline peuvent changer sans

Lisez attentivement ce manuel ainsi que toute étiquette apposée sur l’outil et assurez-vous d’en comprendre le sens avant utilisation. Rangez ces consignes avec l’outil, pour référence ultérieure. Assurez-vous que toute personne venant à utiliser cet outil ait attentivement pris connaissance de ce manuel.

Sachez qu’utiliser un outil conformément aux prescriptions ne garantit pas l’élimination de tous les facteurs de risque. Procédez avec prudence. N’utilisez pas cet outil si vous avez des doutes quant à la manière sûre et correcte de procéder.

notiﬁcation préalable.

Consignes générales de sécurité relatives aux appareils électriques

AVERTISSEMENT Veuillez lire l’intégralité des consignes de sécurité et des instructions. Le non-respect de ces consignes et instructions peut entraîner un

risque de choc électrique, d’incendie et/ou se traduire par des blessures graves

Veuillez conserver ces instructions et consignes de sécurité pour référence ultérieure.

L’expression « appareil électrique » employée dans les présentes consignes recouvre aussi bien les appareils ﬁlaires à brancher sur le secteur que les appareils sans ﬁls fonctionnant sous batterie.

Sécurité sur la zone de travail

a) Maintenir une zone de travail propre et bien éclairée. Des zones

encombrées et mal éclairées sont sources d’accidents.

b) Ne pas utiliser d’outils électriques dans des environnements explosifs,

tels qu’à proximité de liquides, de gaz ou de poussières inﬂammables.

Les appareils électriques produisent des étincelles susceptibles d’enﬂammer la poussière ou les vapeurs présentes.

c) Eloigner les enfants et les passants pendant l’utilisation d’un appareil

électrique. Ceux-ci peuvent provoquer une perte d’attention et faire perdre

la maîtrise de l’appareil.

Sécurité électrique

a) Consulter la rubrique « Branchement sur le secteur » ci-dessous

relativement aux informations de sécurité importantes concernant le branchement de cet appareil sur le secteur. Le non-respect de ces

instructions peut entrainer un risque d’accident fatal.

b) Eviter le contact corporel avec les surfaces mises à la terre telles que

tuyaux, radiateurs, cuisinières et réfrigérateurs. Le risque de décharge

électrique est plus important si le corps est mis à la terre.

c) Ne pas exposer l’appareil électrique à la pluie ou à l’humidité.

L’inﬁltration d’eau dans un appareil électrique accroît le risque de décharge électrique.

d) Ne pas maltraiter le cordon électrique. Ne jamais utiliser le cordon

électrique pour porter, tirer ou débrancher l’appareil. Protéger le cordon électrique de la chaleur, du contact avec l’essence, des bords tranchants et pièces rotatives. Un cordon électrique endommagé ou

entortillé accroît le risque de décharge électrique.

e) Lors d’une utilisation de l’appareil électrique en extérieur, se servir

d’une rallonge appropriée à une utilisation en extérieur. Cela réduit le

risque de décharge électrique.

f) Si une utilisation de l’appareil électrique dans un environnement

humide ne peut être évitée, utiliser une alimentation protégée par un disjoncteur différentiel. L’utilisation d’un disjoncteur différentiel réduit le

risque de décharge électrique.

Sécurité des personnes

a) Rester vigilent et faire preuve de bon sens lors de la manipulation de

l’appareil. Ne pas utiliser un appareil électrique lorsque l’on se trouve dans un état de fatigue, ou sous l’inﬂuence de drogues, d’alcool ou de médicaments. Un moment d’inattention pendant l’utilisation d’un outil

électrique peut se traduire par des blessures graves.

b) Porter un équipement de protection approprié. Toujours porter une

protection oculaire. Le port de masque à poussières, chaussures de

sécurité antidérapantes, casque de sécurité et protections antibruit adaptés aux différentes conditions de travail réduit le risque de blessures corporelles.

c) Eviter tout démarrage accidentel. S’assurer que l’interrupteur

marche-arrêt soit en position d’arrêt avant de brancher l’appareil sur l’alimentation secteur ou d’installer la batterie, de prendre l’appareil ou de le transporter. Porter un appareil électrique tout en maintenant le doigt

posé sur l’interrupteur ou brancher un appareil électrique dont l’interrupteur est sur la position de marche est source d’accidents.

d) Enlever toute clé et tout instrument de réglage avant de mettre

l’appareil électrique en marche. Une clé ou un instrument de réglage

laissé ﬁxé à un élément en rotation de l’appareil électrique peut entraîner des blessures physiques.

e) Ne pas essayer d’atteindre une zone hors de portée. Se tenir toujours

en position stable permettant de conserver l’équilibre. Cela permet de

mieux contrôler l’appareil électrique dans des situations inattendues.

f) Porter des vêtements appropriés. Ne pas porter de vêtements amples

ou des bijoux pendants. Eloigner cheveux, vêtements et gants des pièces en mouvement. Les vêtements amples, les bijoux pendants et

cheveux longs peuvent être happés par les pièces en rotation.

g) Si l’appareil est pourvu de dispositifs destinés au raccord

d’équipements d’extraction et de récupération de la poussière/sciure, s’assurer qu’ils soient bien ﬁxés et utilisés correctement L’utilisation de

ces dispositifs peut réduire les risques dus à la poussière.

Utilisation et entretien des appareils électriques

a) Ne pas forcer sur l’appareil électrique. Utiliser l’appareil électrique

approprié au travail à effectuer. Un appareil électrique adapté et employé

au rythme pour lequel il a été conçu permettra de réaliser un travail de meilleure qualité et dans de meilleures conditions de sécurité.

b) Ne pas utiliser un appareil électrique dont l’interrupteur marche-arrêt

est hors service. Tout appareil électrique dont la commande ne s’effectue

plus par l’interrupteur marche-arrêt est dangereux et doit être réparé.

c) Débrancher l’appareil électrique ou démonter sa batterie avant

d’effectuer tout réglage ou changement d’accessoire et avant de le ranger. De telles mesures préventives réduiront les risques de démarrage

accidentel.

d) Ranger les appareils électriques inutilisés hors de portée des enfants

et ne pas permettre l’utilisation de cet appareil aux personnes non habituées à son maniement ou n’ayant pas lu les présentes instructions. Les appareils électriques sont dangereux dans les mains

d’utilisateurs inexpérimentés.

e) Veiller à l’entretien des appareils électriques. Vériﬁer que les éléments

rotatifs soient bien alignés et non grippés. S’assurer de l’absence de pièces cassées ou endommagées susceptibles de nuire au bon fonctionnement de l'appareil. Si l’appareil électrique est endommagé, le faire réparer avant toute utilisation. De nombreux accidents sont dus à

l’utilisation d’appareils électriques mal entretenus.

f) Veiller à ce que les outils de coupe soient tenus affûtés et propres. Des

outils de coupe bien entretenus, aux tranchants bien affûtés, sont moins susceptibles de se gripper et sont plus faciles à contrôler.

8F8

+ 19 hidden pages

Silverline Gasless Turbo Mig User Manual [en, de, es, fr, it]

Specifications and Main Features

Frequently Asked Questions

User Manual