STL-300 STOPLITE® TacTIcaL LIghT & LaSEr
Tactical Gear Redefined
TM
STL-300 STOPLITE® TACTICAL LIGHT & LASER
The STL-300 STOPLITE is a versatile and powerful
flashlight and strobe packing approximately 450
lumens* of blinding light. Handheld or easily
mounted to an accessory rail, the STOPLITE also
features an adjustable laser aiming module and a
remote momentary On/Off pressure switch. The grip
provides extra stability when mounted on a rifle.
OWNER’S MANUAL
FEATURES
n
450 Lumen* CREE LED
n
3 function modes – steady light, strobe light, laser (with light or independent)
n
Steady On/Off and momentary On/Off operation
n
Remote momentary On/Off pressure switch
n
Quick release rail attachment
n
Ergonomic rubber overmolded grip
CONTENTS
n
STL-300 STOPLITE Tactical Light & Laser
n
Owner’s Manual
n
(4) AA Lithium Batteries
n
Velcro Accessory Pouch
SPECIFICATIONS:
Interface
Retention type
Dimensions
Weight empty
Weight w/batteries
Light type
Power
Light switching
Light modes
Strobe frequency
Visible Laser
Laser switching
Laser modes
Battery
Power management
Run time
*Lumens based on LED manufacturers specifications
Laser Information
Laser Type: Class IIIa visible laser diode
Peak Power: < 5mW
Wavelength: 635nm
Beam Color: Red
This product conforms with 21 CFR 1040.10.
WARNING: Do not point the laser beam at eyes. Permanent eye damage can result. See attached warning label -
M1913 and compatible
Quick release mode/fixed mount mode
6”H x 4.3”L x 2.5”W
12 oz
14 oz
Hi Output LED
450 Lumens peak*
Steady on/off; momentary on/off
Constant; Strobe
18-20 cycles per second
Hi Visibility (635nm), Class IIIa, Red
Independent on/off
Stand-alone; with white light (constant & strobe)
Four AA Lithium batteries
Digital integrated circuit
4 hours peak (continuous operation)
<5mW
WARNINGS
Before handling any firearm with the PRODUCT attached, read and understand the entire contents of
your firearms manual (especially the safety precautions and procedures for safe firearms handling)
and the PRODUCT manual. Failure to follow safety precautions when handling a firearm with the
PRODUCT attached can result in damage to property, serious injury, or death. Once the PRODUCT is
attached to the firearm, the firearm will be pointed at anything the PRODUCT is directed at. Do not
point the PRODUCT at anything or anyone that you do not intend to shoot.
The ON / OFF switch on the PRODUCT allows operation of the laser without placing your finger inside
the firearm trigger guard. Always keep your fingers off the trigger and outside the trigger guard until
you are ready to fire the weapon. Always verify the weapon is free of ammunition and the chamber
clear per the weapon’s operators manual before attempting to mount or dismount the PRODUCT
on the weapon. Always dismount the PRODUCT from the weapon when performing maintenance,
cleaning the PRODUCT, and when replacing batteries. Never place your hand in front of the weapon
muzzle when adjusting the PRODUCT.
Do not operate the PRODUCT around cleaning solvents or flammable/combustible materials,
in environments involving gasses or a flammable atmosphere, or in areas where gasoline, paints,
solvents, or other flammable liquids are stored.
When the laser dims or fails to illuminate, change batteries. Follow battery manufacturers’
instructions for the proper handling, storage, and disposal of batteries. Do not store the PRODUCT with
batteries installed.
BATTERY HAZARD WARNING
Battery manufacturers warn against mixing new and used batteries or different brand batteries
together as this may increase the risk of leakage, fire or explosion. Do not, puncture, short-circuit,
disassemble or heat batteries above 212°F (100°C). Do not recharge the batteries unless they are
specifically designed as rechargeable batteries and then only in accordance with manufacturer’s
directions.
Lithium Batteries: Industry wide there have been reported incidents of off-brand Lithium
batteries exploding or catching fire creating serious consequences. SIGTac includes batteries from
Duracell® and other well-known battery manufacturers with its products, and strongly urges you to
only purchase replacement batteries from Duracell®, or other well-known battery manufacturers like
Panasonic® and Rayovac®. These batteries are designed for use in high performance, high-drain
devices, and their designs incorporate fault and heat protection for added safety. Use of inferior
batteries may cause an explosion or fire, creating risk of damage to your device that will void the
SIGTac warranty, cause damage to other property, and potentially serious injury or death.
STL-300 STOPLITE® TacTIcaL LIghT & LaSEr
Quick release
bar and rail
attachment
450 Lumen*
CREE LED
Laser
aiming
module
Ergonomic
grip contour
Remote momentary
on/off pressure switch
Accessory rail
mounting point
Laser aiming
adjustments
Luminous
momentary
mode light
button
Independent laser
On/Off button
Locking retention
screw
Steady on/off
button
Light and
laser modes
INSTRUCTIONS
Install battery:
n
Open door at bottom of grip using coin or screwdriver
n
Position batteries as shown in picture
n
Close battery door and secure using coin or screwdriver
Getting Started:
n
Turn on light by pressing light power button on side. Select steady or
strobe modes using 2 smaller side buttons.
n
Light must be ON to select or change modes.
n
Last selected mode is retained until changed.
n
n
back. For steady operation, press and release side power button.
n
Steady light mode
For Momentary Operation – depress and hold the large button on
n
Laser light mode
Laser functions independently of either light mode.
Press red button on back of laser aiming module to turn on/off.
For Remote Operation (optional):
n
Install remote momentary on/off pressure switch into remote
switch port.
n
Squeeze remote switch pad at end of cord and hold for momentary
operation. Last selected mode (steady or strobe) is retained
until changed.
Note: This product features digital power management. When battery power drops below
a preset level, the unit shuts down to protect the internal circuitry and prevent a battery
overheating condition. If this occurs, the battery needs replacement.
n
Strobe light mode
Mounting on Firearm:
n
Depress quick release bar and hold
n
Slide STL-300 STOPLITE onto rifle accessory rail
n
Release quick release bar and move STL-300 STOPLITE into place.
n
Secure STL-300 STOPLITE firmly on rail by hand tightening locking
both retention screws.
Laser Aiming Module Adjustment
n
Use screwdriver or coin to make necessary adjustments.
n
Rotate TOP adjustment screw clockwise to move laser UP.
n
Rotate SIDE adjustment screw clockwise to move laser LEFT.
STATEMENT OF LIABILITY
This device is classified as a FIREARMS ACCESSORY and is sold by us with the specific
understanding that we are not responsible in any manner whatsoever for its safe
handling or resale under local laws and regulations. SIGTAC shall not be responsible
in any manner whatsoever for malfunctioning of the firearm, for physical injury or for
property damage resulting in whole or in part from (1) criminal or negligent discharge, (2)
improper or careless handling, (3) unauthorized modifications, (4) defective, improper,
hand-loaded, or reloaded ammunition, (5) corrosion, (6) neglect, or (7) other influences
beyond our direct and immediate control. This limitation applies regardless of whether
liability is asserted on the basis of contract, negligence or strict liability (including
any failure to warn). Under no circumstances shall SIGTac be liable for incidental or
consequential damages, such as loss of use of property, commercial loss and loss of
earnings or profits.
WARRANTY STATEMENT
SIGTac warrants that our sight and illumination tool products are free from defect in parts and
workmanship for a period of ninety (90) days from original date of purchase. At our discretion,
we will repair, replace, or refund your original purchase price of this product if it is determined
to be defective. Normal wear and tear, including lamps burning out, batteries draining, and
switches wearing out, is not covered, nor is damage resulting from abuse, neglect, battery
leakage, or altering this product from its original state.
CONTACT
18 Industrial Drive, Exeter, NH 03833 • (603) 772-2302 ext. 3 • www.sigtac.com
P/N 8500190 Rev 1